Construction of Balance civil work at 400/132/33 KV GIS S/s Sector-123 Noida (Energized 400 KV GIS Building, 132 KV GIS Building, 33 KV GIS Building, CRB, Pump House, Store Room, Guard Room, Energized Switch Yard, 02 No Type-IV, 04 No Type-III, 08 No

Amount

Excavation in foundation in ordinary soil (Loam Clay or Sand) including lift upto 1.5m and lead upto 30m and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of the foundation work. (CSI No. 4.01)

Earth work in cutting or in embankment in ordinary soil, excavation to be in the form of regular pits, not exceeding 0.5M in depth and earthwork in embankment to be in 20cm layers, including ramming & dressing the surface to reqd. levels and slopes. (CSI No. 4.03)

Add to Earth work item (SI No. 4.01 & 4.03) for every additional 30m lead or part thereof or for every additional 1.5M lift or part thereof. (CSI No. 4.04)

River Bed Fine Sand filling in plinth including supply of necessary quantity of fine sand from outside the UPPCL premises including watering, dressing etc. Rate to include cost of all materials, labour and T&P etc. required for proper completion of work.(CSI No. 4.05)

Clearing jungle including uprooting of rank vegetations,grass, bush, wood, trees and saplings of girth upto 30cm measured at a height of 1.0m above ground level and removal of rubbish upto a distance of 50m outside the periphery of UPPCL area cleared. (CSI No. 4.08)

Cleaning of grass and removal of rubbish upto a distance of 50 M outside the UPPCL area cleaned. (CSI No.4.09)

Earth filling under floors and/or corporation area including cost of earth obtained with in 8 km distance outside corporation area and carriage including watering, ramming in 20 cm layers and dressing of earth etc. all complete. (CSI No. 4.10)

Levelling and dressing and making proper slopes including cutting and filling of earth upto a depth 100mm if so required including all labour T&P etc. required for proper completion of the work . (CSI No. 4.11)

Concrete with 4cm gauge stone ballast, coarse sand & cement in proportion of 12:6:1 in foundations &under floors including supply of all materials, labour and tools and plants etc. required for proper completion. (CSI No. 5.02)

Concrete with 4cm gauge stone ballast, coarse sand and cement in proportion of 8:4:1 in foundation & under floors including supply of all materials, labour & T&P etc. complete. (CSI no. 5.04a)

Cement concrete with 2cm gauge approved hard stone ballast, coarse sand and cement in proportion of 4:2:1 including supply of all materials, labour,side shuttering if required and T&P etc. required for proper completion of work. (CSI No. 5.06)

S/F 40 mm thick precast RCC jali (approx 0.5 Sq.M. Size) of approved design with 1:3 cement, coarse sand mortar and 1.6 mm dia M.S.reinforcement with cost of all materials labour and T&P complete including cutting required grooves in walls and grouting. (CSI No. 5.17)

Concreting of 40 mm thick RCC trench covers in mild steel frame work with RCC 1:1.5:3 in Cement, coarse sand and 2cm gauge graded hard stone ballast with 3mm thick floating coat of neat cement finish on top of cover complete with all labour, materials and placing the same in proper position at required location of cable trench within the substation area. (CSI No. 5.18)

Add to CSI no. 5.18 for every extra 5mm or part thickness of trench covers. (CSI No. 5.19)

Cement concrete with 2cm gauge approved hard stone ballast, coarse sand and cement in proportion of 3:1.5:1 including supply of all materials, labour,side shuttering if required and T&P etc. required for proper completion of work (CSI No. 5.21)

Precast cement concrete door sills, chaukhats boundary posts, shelves and similar small work with cement, approved coarse sand and 2 cm gauge graded approved hard stone ballast in the proportion 1:1.5:3, excluding reinforcement but including fixig the same in position including cost of all other material, labor and T&P . (CSI No. 5.22)

RCC work with cement, approved coarse sand and 2 cm gauge graded approved hard stone ballast like granite, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3 in lintels of doors and windows, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P. . (CSI No. 5.23)

RCC work with cement, approved coarse sand and 2 cm gauge graded approved hard stone ballast like granite, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3 in slab, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P (CSI No. 5.24)

RCC work with cement, approved coarse sand and 2 cm gauge graded approved hard stone ballast like granite, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3 in lighter beams i.e. having span upto 6m, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P . (CSI No. 5.25)

RCC work with cement, approved coarse sand and 2 cm gauge graded approved hard stone ballast like granitet, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3 in heavier beams i.e. having span above 6m, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P . (CSI No. 5.26)

RCC work with cement, approved coarse sand and 2 cm gauge graded approved hard stone ballast like granite quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3 Raft & foundations excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P. (CSI No. 5.28)

RCC work with cement, approved coarse sand and 2 cm gauge graded approved hard stone ballast like granite quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3 RCC pile caping, gantry walls/column foundations and RCC pedestals , excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P. (CSI No. 5.28)

RCC work with cement, approved coarse sand and 2 cm gauge graded approved hard stone ballast like granite, quartzite etc from Dalla, Jhansi or other quarries in proportion 1:1.5:3 in RCC T beam-slab and column, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P . (CSI No. 5.29)

Supplying and filling 75 mm to 115 mm size bolders in chilling tank complete including supply of all materials, labour and tools and plants etc. required for proper completion.(Voides 30 % shall be deducted during measurement). (CSI No. 5.30)

Arranging and spreding 75 mm thick broken grit 20 mm (Granite stone) uniform for turfing over 100mm thick base course of C.C. In 1:4:8 (1cement:4coarse sand: 8, 40mm stone ballast) top finish by brooming of cement mortar 1:4(1cement: 4 Coarse sand) including supply of all materials, labour and tools and plants etc. required for proper completion. (CSI No. 5.31)

First class brick work in 1:4 cement and coarse sand mortar in foundation and plinth including supply of all materials, labour & T&P etc. required for proper completion of work (CSI No. 6.03)

First class brick work in 1:6 cement and coarse sand mortar in 230mm thick wall in superstructure including supply of all materials, labour & T&P etc. required for proper completion of work (CSI No. 6.01+6.07+6.08)

First class brick work in 1:4 cement and coarse sand mortar in 115mm thick wall in superstructure including supply of all materials, labour & T&P etc. required for proper completion of work (CSI No. 6.03+6.07+6.09)

Brick work in foundation & plinth with old dismantled bricks (supplied by department free of cost) and coarse sand mortar in 1:6 including supply of all other materials, labour, removing mortar & cleaning of old & used bricks,T&P etc complete. (CSI No. 6.18)

Supply and filling brick bat in soak pit including all labour,material and T&P etc complete. (for 01 soak pit) (CSI No. 6.23)

2.5 cm. thick damp proof course of cement concrete consisting of 1 part cement 1.5 parts approved coarse sand (F.M.1.8 to 2.5), and 3 parts approved 12 mm. graded stone grit and also including liquid water proofing material as approved by the Engineer-Incharge in the proportions specified by the manufacturer. (CSI No. 7.02)

Supply and fixing of 32 mm. thick Shisham wood part panelled and part glazed door and window shutter including supply and fixing of wooden cleats and stoppers and including fixing and adjustment of hinges bolts, locks, handles, springs and/or other fittings but excluding their supply and including fixing the glass panes with putty and necessary screws (Glass panes to be 4 mm thick.)(CSI No. 8.25)

S/F Galvanized Mosquitos proof heavy quality iron wire gauge (14x24) over window frames and including supply ofShishum wood battens 8cm x 1cm. and including supply and fixing of necessary screws, all materials,labour and T&P etc. required for proper complete. (CSI No. 8.44)

S/Fixing of double action floor springs including cutting in floors / RCC slabs and grouting the same with C.C. & finishing the surface properly as and where required under aluminium doors as per direction of Engineer-in-charge. including cost of all other material, labour, tools & plants etc. complete. (CSI No. 8.52)

S/Fixing of single action floor springs including cutting in floors / RCC slabs and grouting the same with C.C. & finishing the surface properly as and where required under aluminium doors as per direction of Engineer-in-charge. including cost of all other material, labour, tools & plants etc. complete.(CSI No. 8.53)

Supply and fixing of 32 mm thick single leaf flush door shutter ( boiled water resistance, phenol maldehide resin bonded, hot pressed factory made) commercial quality to I.S.2202 part-1 (1983) ISI marked including fixing of wooden cleats and stoppers and including fixing and adjustment of hinges,bolts.locks,handles, springs and other fittings but excluding their supply including all materials, labour & T&P etc. required for proper completion of work. (CSI No. 8.54)

Supply and fixing brass polished hydraulic door closure of approved make & quality its fixing and adjustment with the help of screws, nuts and bolts including supply of all labour, T & P etc. required for proper completion of the work. (CSI No. 8.57)

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement ,Door handle, lock and stopper etc and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge(CSI No. 8.66)

Mild Steel or Iron work in heavy sizes such as trusses built up gates, door frames, record, racks roof work gates etc. wrought to required form including holes rivetting or welding where necessary and also fixing in proper position and alignment including cost of all materials supplied by contractor. (CSI No. 9.01)

TMT/Tor steel in plain work such as reinforced concrete or reinforced brick work (when not included in an over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage, bend, hooks and authorized overlapping shall be measured. (Steel shall be arranged by the contractor) (CSI No. 9.03)

Supplying and fixing rolling shutters of approved make made of 80x1.25 mm. Gauge cold rolled M.S. lathes inter locked through out their inner length and joined together at the end by end lock guides & arrangements for inside and outside locking with push &pull operation complete but excluding the cost of top cover and springs. CSI No. 9.08)

P/F 27.5cm. long wire spring grades 2 for rolling shutters. (CSI No. 9.09)

Providing and fixing top cover rolling shutters. (CSI No. 9.10)

Providing & fixing ball bearing for rolling shutters. (CSI No. 9.11)

Supply of 28 mm. dia M.S. Anchor bolts (conforming to IS 266) 900 mm. long with base plate (75x75x6mm) welded with anchor bolts including its threading upto a length of 10cm. and also supply of a pair of galvanized standard nuts with threading including supply of 5 mm thick washer and cost of labour, material & T&P for proper completion of work(CSI No. 9.12)

Fixing and grouting 28 mm and above dia bolts in proper alignment level and setout with help of a template complete including supply of all labour & T&P etc. required for proper completion of the work.(labour rates only) . (CSI No. 9.13)

Supply of 25 mm dia.M.S. Anchor bolts (conforming to IS-226) 500 mm long with base plate(50x50x6 mm)welded with anchor bolts,including its threading upto a length of 10cm. and galvanizing upto 15cm from top, also supply of a pair of galvanized standard nuts with threading including supply of 5mm thick washer and cost of labour material and T&P etc. required for proper completion of the work. (CSI No. 9.14)

Fixing and grouting 25 mm and below dia M.S. Anchor bolt in proper alignment level and setout with the help of a template including supply of all labour T&P etc. reqd. for proper completion of the work. (labour rates only) . (CSI No. 9.15)

Supply and fixing galvanised mosquito proof jali (16x24 gauge) with M.S. flat of 20 x 3 mm. size, on both sides screwed or welded to window or door frame. (CSI No. 9.18)

Providing M.S. Frames work, rack etc for R.C.C. Trench covers and edging with M.S. angles and M.S reinforcement including cutting, bending and welding as per approved drawing. The rate is including cost of all labour, materials etc. as required for proper completion of the work. (CSI No. 9.20)

S/F welded wire mesh size 75x25mm and rectangular made out of 10 SWG over M.S. angle frame with M.S. flat welded as required including cost of drilling holes, washer welding etc as required including cost of all material, labour and T&P etc. required for proper completion of work . except cost of M.S angle and flat. (CSI No. 9.22)

S/F 50x50mm, 8 gauge G.I. chain link fencing 1.8 M high including fixing to vertical posts, horizontal runners with 10mm dia. 40mm long bolts, nuts and washers complete with all material, labour and T&P etc. required for proper completion of work. Chain link of 8 gauge shall be galvanized by hot dipped method as per relevant IS Code. (Excluding cost of vertical posts and horizontal runners) (CSI No. 9.23)

Grouting of vertical or inclined post of pale/chain/security fencing in true level, alignment and in plumb or inclination as required, including cost of all labour, materials and T&P required for proper completion of work. ( Post and concrete for grouting shall be measured separately) (CSI No. 9.28)

Fixing and grouting of trench edging in proper level and alignment including cost of all labour, and T&P etc. required for proper completion of the work but excluding cost of C.C. (labour rates only) . (CSI No. 9.30)

Fixing of template in position, level and alignment for grouting of anchor bolt for auxiliary structure. (labour rate only). (CSI No. 9.32)

Fixing of cable trench racks in proper position and alignment including cost of all labour, material and T&Petc. required for proper completion of the work (Labour rate only). (CSI No. 9.33)

Providing & fixing 1 mm.thick M.S. sheet garrage door with frame of 40x40x6mm angle iron, diagonal bracings with 50x5 mm flat and 5 mm thick M.S. gusset plates at the junctions and corners including supply and fixing of necessary fitting, 2 no lock rail of 16 dia,375 mm long and including pintel hooks at the top and bottom, applying a priming coat of red oxide paint on all sides complete . (CSI No. 9.34)

P/F Concertina coilfencing with required dia. 600 mm upto 3 M height of wall between existing angle iron ‘Y’ shaped placed 2.4 M or 3.0 M apart and with 6 horizontal R.B.T. stud tied with G.I. staples and G.I. clips to retain horizontal including necessary bolts or G.I. barbed wire tied to angle iron all complete ( No. of rounds will be 7 to 8 in one Meter length) as per direction of Engineer I/C with reinforced barbed tape (R.B.T.)/ Spring core (2.5mm thick ) wire of high tensile strength of 165 kg/Sqmm with tape ( 0.52 mm thick ) of supreme make or equivalent and weight 43.478 gm/meter ( cost of MS angle, C.C. blocks shall be paid separately).(CSI No. 9.37)

Supply and fixing 24 B.W.G , G.C. Iron Sheet roofing .fixed in position with J or U bolts 10 mm. dia with G.I. Limpet & bitumen washers including supply of all materials, labour,wastage. and T&P etc. required for proper completion of the work. (CSI No. 10.01)

Supply and painting of 85/25 grade bitumen paint over roof @ 1.7 Kg/ sq.m.and spreading 6 mm.size grit over it @ 1 cft /100 Sq.Ft. including sweeping, cleaning the roof with brush, heating the paint to required temterature and supply of all materials, labour and T&P etc. required for proper completion of the work. (CSI No. 10.12)

12 mm thick plaster with cement mortar consisting of one part of cement & four part of coarse sand (1:4), minimum thickness not to be less then 10 mm including supply of all material, labour and T&P etc for proper completion of work. (CSI No. 11.07)

Rough cast finish to plasters of different mortars,add extra to plaster items. (CSI No. 11.11)

Add for extra labour and materials for plaster over rough face of one brick thick wall. (CSI No. 11.12)

2 cm. thick cement plaster in dado or skirting in 1:2 consisting of one part of cement and two parts of approved coarse sand laid in panels finished with 3mm.floating coat of neat cement or cement and marble dust in ratio of 5:1 including supply of all materials, labour & T&P etc. required for proper completion of the work. (CSI No.11.13)

S/mixing approved water proofing compound (CICO,DR FIXIT etc) in cement mortar in plaster or concrete work in the proportion as recommended by the manufacturer. (CSI No. 11.15)

Providing (12x15) mm section groove in plaster including all material, labour and T&P etc. required for proper completion of the work. (CSI No. 11.16)

6 mm. thick plaster with 1:3 cement & coarse sand including labour, materials & T&P etc. required for proper completion of the work. (CSI No. 11.17)

Champering the edge of concrete in auxiliary structure, of size 25 mm wide in triangular section including all materials, labour & T&P etc complete. (CSI No.11.18)

Making drip coarse (25x12) mm in 1:2 cement and coarse sand including supply of all materials, labour and T&P etc required for proper completion of work. (CSI No. 11.19)

3 mm thick floating coat of neat cement finish including supply of all materials,labour and T&P etc. required for proper completion of the work.( cement consumption 0.044 bag/Sq.m.) (CSI No. 11.20)

4.0 cm thick 1:2:4 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and T&P etc, required for proper completion of the work. without base CC (CSI No. 12.04)

First class bricks on edge floor laid dry, joints sand filled, including preparation of base to proper slope and its ramming including supply of all material labour & T&P etc. required for proper completion of the work. (CSI No. 12.07)

Supply and Laying 8 mm thick glazed floor tiles of Somany, Johnson or equivalent make, , laid with 1:3 cement and approved coarse sand mortar finished with white cement slurry, jointing and polishing complete, including supply of all materials, labour and T&P etc. required for proper completion of the work. (CSI No. 12.11)

Providing and fixing glass strips of 3.15 mm thickness & 40mm depth in joints of floor and skirting at the time of laying floors, flush with floor level including supply of all materials, labour& T&P etc. required for proper completion of work. (CSI No. 12.14)

Providing and laying 18 mm. thick Kota stone in flooring or skirting over base cement mortar 1:4 mix and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete and including supply of all materials labour and T&P etc required for proper completion of the work. (CSI No. 12.17)

Providing and laying floor of 8 mm thick vitrified tiles in flooring or skirting of approved brand (Bell, Johnson or equi. make) size of 600x600 mm of approved shade, colour and pattern , laid over base cement mortar 1:4 mix including finishing the joints with white cement mixed with pigment to match the shade of tile including cost of all material, labour and T&P required for proper completion of the work. (CSI No. 12.18)

Providing and laying of 16 mm thick granite ( black/ brown) in flooring or skirting ,of approved shade, colour,size and pattern , laid over base cement mortar 1:4 mix including finishing the joints with white cement mixed with pigment to match the shade of granite floor including cost of all material, labour and T&P required for proper completion of the work, as per direction of Engineer incharge. (CSI No.12.20)

S/F 10mm thick Group 25 acid resisting tiles of “Somany” or equivalent approved make in flooring or skirting (confirming to I.S. 4457 - 1967) in ordinary Portland cement and coarse sand in ratio 1:3 with the joints filled with acid resistant cement “Accocide” of A.C.C. or equivalent make acid resistant cement and liquid supplied with cement, mixed in 1:3 ratio to make a workable paste in G.I. Tray. The joints should be kept as 5mm and to be cured for 7 days with dilute HCL (One part acid and three parts of water). Rate should be including the cost of all materials, labour and T&P etc. required for proper completion of the work. (CSI No. 12.22)

Supply and laying of 80 mm thick I shaped mechanically compressed inter locking cement concrete paver block manufactured by high pressure & controlled vibration machine having plan dimension 200X(160+120 mm) with minimum 5 mm thick toping of O.P.Cement mixed with 25% marble powder. The compressive strength of concrete pavers blocks shall not be less than 30 MPa & 4.5 Kg/No. including cost of all material, labour, T&P etc. required for proper completion of work as directed by Engineer-in-charge but excluding G.S.T. which shall be paid extra as per rules. (CSI No.12.23)

Providing and laying of 16 mm thick baroda green stone in flooring or skirting,of approved shade, colour,size and pattern , laid over base cement mortar 1:4 mix including finishing the joints with white cement mixed with pigment to match the shade of granite floor including cost of all material, labour and T&P required for proper completion of the work, as per direction of Engineer incharge. (CSI No.12.30)

Painting or varnishing new iron work in small areas or new wood work with one coat of ready mixed priming paint and one coat of approved superior quality ready mix paint "Luxol" or equivalent brand or varnish including supply of all materials, labour and T&P etc. required for proper completion of the work. Paint to be used should conform to the I.S. 103-1950. (CSI No. 13.01)

As in item 13.01 above but for every coat after first coat. (CSI No. 13.02)

As in item 13.01 above but for every coat on previously painted old wood or iron work including its sand papering,rubbing and cleaning as required, for proper completion of work. (CSI No. 13.03)

Removing paint or varnish with paint remover or with caustic soda including supply of all materials,labour and T&P etc. required for proper completion of the work. (CSI No. 13.07)

One priming coat and one coat oil bound distemper on new work including supply of all materials,labour and T&P etc. required for proper completion of the work. (CSI No. 13.08)

As in item 13.08 but for every coat after the first coat. (CSI No. 13.09)

As in item 13.08 but for every coat on previously old oil bound distemper surface. (CSI No. 13.10)

Applying Birla or equivalent putty on new interior or exterior surface over one coat of water based cement primer of ICI or equivalent brand for smoothening and levelling of the surface as per requirement and direction of Engineer I/C including cost of all material, labour, T & P etc required for proper completion of work. (CSI No. 13.20)

Applying BIRLA PUTTY or equivalent putty on previousaly bila putty smoothen surface over one cost of water base cement primer of ICI or equivalent brand for smoothining and leveling of the surface as per requirement and direction of E/I including cost of all material , labour and T&P required for proper completion of work.(CSI No.13.21)

Painting one coat with APEX or equivalent brand weather coat paint on new wall surfaces (well prepared with Birla putty and one coat of primer ICI or equivalent which shall be paid separately) including through washing with water including cost of all materials, labour, T&P required for proper completion of work. (CSI No. 13.22)

Same as in item no 13.22 above but for every coat of additional APEX or equivalent brand weather coat paint . (CSI No. 13.23)

Same as in item 13.22 but for each coat of APEX or equivalent brand weather coat paint .on previously treated surface. (CSI No. 13.24)

Dismantling brick work or stone work in lime or cement mortar and including stacking of materials as directed by the Engineer-in-charge within a distance of 60 metres. (CSI No. 15.01)

Dismantling reinforced cement concrete or reinforced brick work, including stacking of dismantled materials as directed by the Engineer-Incharge within a distance of 60 metres. (CSI No. 15.03)

Dismantling cement concrete or brick or granolithic floors including base concrete and including stacking of dismantled materials as directed by the Engineer In-charge within a distance of 60 metres. (CSI No. 15.05)

Dismantling existing plaster including disposal of refuse as directed by the Engineer-I/C within a distance of 60 M. (CSI No. 15.11)

Dismantling of existing R.C.C. Gantry/ Auxiliary foundation with the help of mechanical means in switchyard including disposal of refuse/ debris as per direction of Engineer - in - charge. Including all labour and T&P etc. required for proper completion of the work. (CSI No. 15.15)

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber & consolidating with road roller including making good the undulations etc.& re-rolling the sub grade & disposal of surplus earth with lead upto 50 metres. (CSI No. 18.01)

Scraping old painted surface including disposal of scraped material to a distance of 30 m. (100') as directed by Engineer - in - charge. (CSI No. 18.10)

Laying cement concrete road slab consisting of 1 part cement 2part approved coarse sand and 4 part approved 20mm down graded stone aggregate over prepared sub grade after its rectification and bringing it to proper camber and shape,finishing with TRIMIX machine ,concrete hardner and making good to the satisfaction of E/I inclduing cost of all materials, labour and T&P etc. required for proper completion of the work. (CSI No. 18.12)

Providing and laying non-pressure NP3 class RCC pipes with collars with stiff mixture of cement mortar in the proportion 1:2 (1-Cement, 2-Coarse sand) including testing of joints including cost of all material, labour, T&P etc. required for proper completion of the work. (CSI No. 18.16)b- 300 mm dia RCC pipe

Supply and stacking of compost manure at site including carriage upto 3 km ( Manure measured in stacks will be reduced by 8% for payment). (CSI No. 23.04)

Supply and stacking of local sand at site including charges of royalty and carriage of the same at site including all leads after 8 kms. (CSI No. 23.05)

Mixing earth sand and manure in proportion specified or directed by the engineer I/C. (CSI No. 23.06)

Spreading of manure sand and good earth mixed in required proportion ( cost of manure, good earth & sand to be paid separately ) (CSI No. 23.07)

Supply and plantation of approved 2 years old plants duly planted in earthen Gamla of approximate size 300x 300 mm nominal size, filled with compost manure and sand mixed in approved proportion including cost of approved quality earthen gamla, compost manure, sand all other materials, labour and T&P etc reqd. for proper completion of work. (CSI No. 23.08)

As in item no 23.08 above but in mosaic gamla. (CSI No. 23.09)

Supply and planting seasonal flower plants such as Genda, Rose, Ostar, Flox, Guldawadi,Gulmehndi, Cochia etc. including digging hole of proper size, manure and treatment with proper chemical etc., including cost of fertilizer, manure, all materials, labour and T&P etc complete in allrespects. (CSI No. 23.10)

Supply and planting permanent ornamental plant like Croten, Varil pristal, Glodulus, Lily, Fern, Bogenbelia etc. including cost of plants, manure, pesticides, fertilizer, labour and T&P etc complete also including preparation of flower bed. (CSI No. 23.11)

Supply and planting Ashoka, Pendula, Mango, Neem,Peepal,Sheesham etc in pits including cost of all materials, labour and T&p etc complete in all respects.(CSI No. 23.12)

Supply and planting Desi Doob grass in lawn including cost of Doob, fertilizer, manure,labour, T&P and preparation of bed complete in all respects. (CSI No. 23.13)

Supply and planting of Garden Grass (Australian). including cost of plants, manure, pesticides,fertilizer, labour and T&P etc complete also including preparation of bed. (CSI No. 23.14)

Hedge plantation in a row distance between two hedge 15 to 25 cm including digging hole 6” to 12” ,manure and treatment with proper chemical etc., including cost of all materials,labour and T&P etc complete in all respects. (CSI No. 23.16)

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work (CSI No. 28.19)

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. (CSI No. 28.20)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). (CSI No. 28.21)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.5 mm thickness (CSI No. 28.23)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever requiredincluding cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) (CSI No. 28.24)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever requiredincluding cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Polyester Powder coated aluminium (minimum thickness of powder coating 50 micron) (CSI No. 28.25)

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm. (CSI No. 28.28)

Providing and fixing false ceiling at all heights with integral densifiedr Armstrong false ceiling tiles of Size 595x595 x12 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as perBS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6 SUB HEAD : 26- NEW TECHNOLOGIES AND MATERIALS 1632 mm reveal profile white/black),comprising of main-T runners of size 15x42 mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross-T of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in- Charge. 26.23.1 With 12 mm thick Armstrong Miniral Fobre Sound Absorbing Sheet (CSI No. 28.30)

Providing and fixing ACP in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With ACP of 4.0 mm thickness (CSI No. 28.31)

Providing & laying of 2 mm thick epoxy flooring with chemcical (conpro EP 2P,conpro EP 36,conpro EPSL1) including all materials, labour & T&P etc. required for proper completion of work. (CSI No.28.32)

Supply and Fixing of 5 blade Exhaust fan ventile air dx 225 mm of Havells or equivalent make including all material, T&P etc required for proper completion of work as approved by engineer in charge.(CSI No. 28.38)

Supply and Fixing of 3 blade ceiling fan 1200 mm of Havells or equivalent including all material, T&P etc required for proper completion of work as approved by engineer in charge.(CSI No. 28.39)

Developing the tubewell by the air compressor having a capacity of 8.5 CuM or by the borehole pumping set having the capacity of 0.7 CuM/sec as per direction of Engineer I/C. (CSI No. 19.01)

Arranging Chemical and bacteriological test of water from reputed lab and submission of report to E/I. (CSI No. 19.02)

Cleaning and dressing of site for tube well boring including cost of all labour, materials and T&P required for proper completion of work. (CSI No. 19.03)

Drilling bore from G.L. to 180 M B.G.L., work to be completed as per direction of Engineer I/C . (CSI No. 19.04) F) As per 19.04 above but for 250 mm dia. boring. (1) from 0 M BGL to 90 M BGL.

Providing 160mm dia Plain PVC CASING PIPES (Aroma /Supreme) (Pressure10 Kg./ Sqcm.) for making tubewell assembly and cartage to boring site, including cost of all labour, materials and T&P required for assembly making and proper completion of work.(CSI No. 19.09)

Supply and fixing of PVC top plug of heavy quality including all labour material & T&P. (CSI No. 19.20) a)160 mm dia.

Supply and fixing of 1.20m long holding support clamps for 300 to 100mm dia tube well pipes. made out of MS flats, pairs of bolt-nuts etc complete with all material, labour, T&P. (CSI No. 19.21)

Supply and fixing of G.I. ("B" class ) column pipes JTC/ JINDAL make with column coupling socket as required for proper completion of work including all labour material & T&P.(CSI No. 19.22) a)80 mm dia.

Supply and fixing C.I. non-return valve ISI marked and approved make with nuts, bolts, packing etc complete including all labour material & T&P. (CSI No. 19.23) A)80 mm dia.

Supply and fixing support clamps for column pipes made out of MS flats, pairs of bolt-nuts etc complete with all material, labour, T&P. (CSI No. 19.24(A))80 mm dia

Supply and stacking pee gravel properly at levelled ground for measurement as directed by Engineer I/C, including all labour, T&P required for proper completion of work. (CSI No. 19.25)

Lowering of M.S. column pipe in tubewell including supply of nuts, and bolts, packing and also carriage of pipe from workshop to site including all labour, T&P etc. required for proper completion of the work. (CSI No. 19.27) a)80/65 mm dia.

Transportation and installation of tube well drilling Rig m/c, compressure for development and other required equipments and accessories at site of work and dismentlling & taking them back after successful completion of the work including cleaning, levelling - dressing the site properly, also disposing off the surplus earth, silt, sand etc. (CSI No. 19.28)

Supply and installation of 5H.P. Kirloskar or equivalent make single stage, horizontal, self priming,three phase dewatering pumpset of specification Head 14/16 M, Discharge 13.6/10 LPS, solid handle size 15.5 mm, suction 80 mm, delivery 80 mm, RPM 1500 including cost of 80 mm dia G.I. pipe for suction (3M) and delivery (4.5 M). (CSI No. 19.29)

Supply & installation of electrical control panel of L&T / Havells or equivalent make for submersible pump / pumpset containing contractor relay condenser. (CSI No. 19.31) d) for 5 H.P pump set three phase

Supply & Installation of submersible pump of K.S.B/ CALAMA. or eqt. make including cost of labour, T&P and material required for completion of work. (CSI No. 19.32) e) three phase 5 HP outlet 50 mm dia. or more, Head 60/24, Discharge 9000/24000 LPH

Supply and fixing of submersible cable Havels or equivalent make, for submersible pump complete in all respect. (CSI No. 19.33) c) 4.0 mm2 for pump above 3 HP and up to 7.5 H.P.

Supply & fixing of steel wire rope for submersible pump including cost of labour, T&P and material required for completion of work. (CSI No. 19.34)

Providing and fixing 50 mm dia Jindal, JTC, ISI marked G.I. pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes external GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.02)

Making water connection of GI pipe line with GI Mains ( 25 mm to 100 mm ) dia. by providing and fixing Ferrule (25 mm dia) GI union and nipple including cutting and threading the pipe, inspection, testing, cutting and making good the road, executing bond with Nagar maha palika, fixing of pipe line upto the points near the building complete work including supply of all materials, labour and T&P etc. required for proper completion of work. (CSI No. 26.03)

Providing & fixing half turn 15mm dia gate valve, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.05a)

Providing & fixing half turn 20mm dia gate valve, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.05b)

Providing & fixing half turn 25mm dia gate valve, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.05c)

Providing & fixing half turn 32mm dia gate valve, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.05d)

Providing & fixing half turn 40mm dia gate valve, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.05e)

Providing & fixing half turn 50mm dia gate valve, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.05f)

Providing and fixing full way 50mm dia G.M. gate valve with wheel, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.04f)

Providing and fixing full way 80mm dia G.M. gate valve with wheel, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.04h)

Providing and fixing NON RETURN REFLEX VALVE, 50 mm dia ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.07f)

P/F GI UNIONS NOMINAL BORE 50 mm, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.10f)

P/F GI UNIONS NOMINAL BORE 80 mm, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.10h)

Maintenance of terraced roof including filling up cracks before rain with approved bituminous filler and stopping leaks during rain including supply of all materials, labour and T&P etc. required for proper completion of the work. (CSI No. 20.01)

Applying two coat of Dr. Fixit pidicrete URP with cement slurry of one parts of Dr. Fixit pidicrete URP (covering area of urp - 2.00 to 2.2 Sqm/Kg) and 1.5 parts of cement on Horizontal and vertical damp surface. Before application clean the surface with wire brush or scrubber to remove hidden dirt, loose particles, laintance and dust, degrease the surface by using suitable solvent thoroughly saturated the surface with portable water but at the time of application water should not be accumulated at any place as per direction of E/I including supply of all materials , labour and T&P etc required for proper completion of work. (NSI)

Renewing panes of 4.8 to 5.7 mm glass including supply of glass with putty and brads including supply of all materials, labour and t&P etc. required for proper completion of the work.(a) glass of 5 mm thick. (CSI No. 20.04)

Easing door and windows. (CSI No. 20.05)

Cleaning panes of glass with spirit of caustic soda including supply of all materials,labour and T&P etc.required for proper completion of the work. (CSI No. 20.09)

Placing of trench cover of all size in proper position including transportation from different places within the S/S area including all labour, T&P etc. required for proper completion of the work as per direction of Engineer - in - charge. (CSI No. 20.11)

Cleaning of septic tank including disposal of waste out side the UPPCL area as per direction of the Engineer-in-charge including cost of all labour,T&P etc.required for proper completion of the work.(CSI No. 20.12)

Cleaning of inspection chamber including disposal of waste out side the UPPCL area as per direction of the Engineer-in-charge including cost of all labour,T&P etc.required for proper completion of the work.(CSI No. 20.13)

Disposal of rubbish / debris out side the UPPCL area as per direction of Er/in- charge including cartage, labour and materials, T&P etc. required for proper completion of the work. (No. deduction for voids shall be made). (CSI No. 20.16)

Cleaning and opening of chocked W.C./ bath / kithchen pipe line including opening and refixing of chamber cover including washing etc. complete.(Analysis based on NBO - 11 25.020.(CSI No. 20.19)

Opening, cleaning, overhauling, oiling and greasing of defective rolling shutter and also re setting of its springs for its smooth functioning including cost of all materials, labour and T&P etc.( Approx. size of shutter 2x2.5) (CSI No. 20.20)

S/laying chicken mesh of (20 mm.)hexagonal heavy quality over roofs of joints of roof as per direction of the Engineer - in - charge.(CSI No. 20.21)

Removal of old and damaged sunfilm from the glass panes of door and window shutters,including removal of Glue completely and carefully by scraping or by any means including cost of all materials, labour T&P etc. required for proper completion of the work.

Providing and fixing sun-film of Gareware or equivalent make on glass panes of door and window shutters including cost of all materials,labour and T&P etc. required for proper completion of the work.

Attending to petty maintenance service like plumbing service,welder service, mansion service and carpenter service required as below. Job attending by one no. Plumber/welder/mason/carpenter with one no. helper per hour or part of an hour.

Providing and fixing PVC CONNECTION PIPE,450X15 with 2 brass units ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.09b)

Supply and fixing of Syntex or equivalent make water storage tank including all materials, labours, T&P etc required for proper completion of work. (CSI No. 26.12)

Providing and fixing CP BRASS BIB COCK15 mm dia. HEAVY QUALITY ( 400gm) ( L & K and equi.) fittings, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work. (CSI No. 26.16A)

Providing and fixing CP BRASS SHOWER HEAVY QUALITY ( > 225 gms )

Providing and fixing CP BRASS wash basin mixer HEAVY QUALITY ( L & K and equi.)

Providing and fixing CP BRASS wall mixer HEAVY QUALITY( L & K and equi.)

Providing and fixing CP BRASS Angle Valve HEAVY QUALITY ( L&K or equi. )

Providing and fixing CP BRASS Piller cock HEAVY QUALITY ( L&K or equi. )

Providing and fixing of 110 mm dia PVC pipe 6 Kg/ Sq.cm for with special such as Tee, bend, socket, elbow etc including supply of all labour,material,T & P etc complete required for proper completion of work. (CSI No. 26.17)

Providing and fixing 20 mm dia ISI Approved CPVC pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.20)

Providing and fixing 25 mm dia ISI Approved CPVC pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.21)

Providing and fixing 32 mm dia ISI Approved CPVC pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.22)

Providing and fixing 40 mm dia ISI Approved CPVC pipes complete with special such as bend, tee, socket, cross, clamp etc earth work including filling the trenches etc required for proper completion of the work. the rate also includes concealed GI fitting where required, cutting and making good the walls etc and all materials, labour and T&P complete. (CSI No. 26.23)

Providing and fixing of 150 mm dia PVC pipe of 6 Kg/sqcm with special such as Tee, bend, socket, elbow etc including supply of all labour,material,T & P etc complete required for proper completion of work. (CSI No. 26.25)

S/F of 16 mm thick Armstrong Miniral metal Sound Absorbing Sheet rate include cost of labour material T&P for completion of work.. (CSI No. 26.40)

Providing and fixing first quality white glazed "Orissa" pattern W.C.Pan Hindustan, Cera make. size 580 mm.(Hindustan,Cera Make) with out "P" trap including supply of all materials,labour and T&P etc.complete. (CSI No. 27.01)

Providing and fixing first quality white glazed " European type." pattern W.C.Pan Hindustan, Cera make. size 580 mm.(Hindustan,Cera Make) with out "P" trap including supply of all materials,labour and T&P etc.complete. (CSI No. 27.02)

Providing and fixing PLASTIC SEAT COVER COMPLETE WITH PLASTIC LID FOR EUROPEAN TYPE WC ISI MARKED including supply of all materials,labour and T&P etc.complete. (CSI No. 27.04)

Providing and fixing flat back 465 mm.x 355 mm x 265 mm. size lipped front urinal basin of white glazed earthern ware first quality (Hindutan, Neycer make) I.S.I. marked including supply of all materials,labour and T&P etc. required for proper completion of the work. (CSI No. 27.05)

Providing and fixing DIVISION PLATE 600X300 mm WHITE GLAZED FOR URINALS I.S.I. marked including supply of all materials,labour and T&P etc. required for proper completion of the work. (CSI No. 27.07)

Providing and fixing 550X400 mm wash hand basin of white glazed earthern ware first quality I.S.I. marked (Hindustan,Neycer / Cera make) including supply of all materials, labour and T&P etc. required for proper completion of the work. (CSI No. 27.08)

Providing and fixing 10 litres low level PVC flushing cistern, COMPLETE WITH ALL FITTINGS including supply of all materials, labour and T&P etc. required for proper completion of the work. (CSI No. 27.12)

Providing and fixing in position 32 mm. dia P.V.C. flush pipe. for W.C. with unions, bends etc. including supply of all materials,labour and T&P etc.required for proper completion of the work. (CSI No. 27.13)

Providing and fixing in position 32 mm. dia P.V.C. WASTE PIPE FOR WASH BASIN. including supply of all materials,labour and T&P etc.required for proper completion of the work. (CSI No. 27.14)

Providing and fixing 600 mm x 450 mm beveled edge mirror of Atul,Kiran makeglass with Indian polish 6.50 mm thick complete with back of 600 mm x 450 mm x 6 mm hard board sheet fixed to wooden cieats with C.P. brass screws and washers including supply of all materials, labour and T&P etc.required for proper completion of the work. (CSI No. 27.15)

Providing and fixing 750 mm x 20 mm size C.P. brass towel rail of approved quality including brackets including supply of all materials,labour and T&P etc. required for proper completion of the work and cutting and making good the wall plaster etc. required for work. (CSI No. 27.16)

Providing and fixing soap dish chromium plated with brackets fixed to wooden cleats with brass screws including supply of all materials,labour and T&P etc.required for proper completion of the work. (CSI No. 27.19)

Providing and fixing 100 mm dia PVC "P" or "S" trap including cement concrete and all materials, labour cartage T&P etc.required for proper completion of the work.(For W.C.) (CSI No. 27.24)

Providing and fixing CI GRATING 100 mm dia including all materials, labour cartage T&P etc.required for proper completion of the work. (CSI No. 27.25)

Providing and fixing Stainless Steel sink 610x450x200 mm Heavy Quality( ISI MARKED ) including all materials, labour cartage T&P etc.required for proper completion of the work. (CSI No. 27.26)

Providing and fixing CI COVER WITH FRAME COMPLETE 450 mm INTERNAL Dia. including all materials, labour cartage T&P etc.required for proper completion of the work. (CSI No. 27.27)

Providing and laying SWR, PVC ( Finolex or equivalent ) pipe including cost of excavation, C.C etc including its jointing and connection, all materials, labour and T&P etc. required for proper completion of the work. (CSI No. 27.29) b) 90 mm Dia.

Providing and laying SWR, PVC ( Finolex or equivalent ) pipe including cost of excavation, C.C etc including its jointing and connection, all materials, labour and T&P etc. required for proper completion of the work. (CSI No. 27.29) c )110 mm Dia.

Providing and fixing SWR, PVC ( Finolex or equivalent ) Bends including cost of all materials, labour and T&P etc required for proper completion of the work. (CSI No. 27.30) b) 90 mm dia.

Providing and fixing SWR, PVC ( Finolex or equivalent ) Bends including cost of all materials, labour and T&P etc required for proper completion of the work. (CSI No. 27.30) c)110 mm dia.

Providing and fixing SWR, PVC ( Finolex or equivalent )Trap including cost of all materials, labour and T&P etc required for proper completion of the work. (CSI No. 27.31) b) 90 mm dia.

Providing and fixing SWR, PVC ( Finolex or equivalent )Trap including cost of all materials, labour and T&P etc required for proper completion of the work. (CSI No. 27.31) c)110 mm dia.

Providing and fixing SWR, PVC ( Finolex or equivalent ) Socket including cost of all materials, labour and T&P etc required for proper completion of the work. (CSI No. 27.32) b) 90 mm dia.

Providing and fixing SWR, PVC ( Finolex or equivalent ) Socket including cost of all materials, labour and T&P etc required for proper completion of the work. (CSI No. 27.32) c) 110 mm dia.

Providing and fixing SWR, PVC ( Finolex or equivalent ) plain Tee including cost of all materials, labour and T&P etc required for proper completion of the work. (CSI No. 27.34) b) 90 mm dia.

Providing and fixing SWR, PVC ( Finolex or equivalent ) plain Tee including cost of all materials, labour and T&P etc required for proper completion of the work. (CSI No. 27.34) c) 110 mm dia.

Supply & wiring of submain with two number 2.5 Sq.mm FRLSH PVC insulated 110 V grade multistrand single core copper cable in 20mm dia heavy duty (2mm thick) PVC conduit concealed in wall with one No. 1.5 Sqmm FRLSH PVC insulated multistrand copper conductor cable as earth contuiity wire drawn in conduit.

Supply & wiring of submain with two number 4 Sq.mm FRLSH PVC insulated 110 V grade multistrand single core copper cable in 20mm dia heavy duty (2mm thick) PVC conduit concealed in wall with one No. 2.5 Sqmm FRLSH PVC insulated multistrand copper conductor cable as earth contuiity wire drawn in conduit.

Wiring Point For light with 1.5 Sq.mm FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit with 1.5Sqmm FRLSH PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit.

Wiring point for for two ways with 1.5 Sqmm FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit pipe concealed in the wall with 1.5 Sq. mm FRLSH OVC insulatyed multistrand copper cponductor cable as earthwire drawn inside the conduit.

Wiring point for fan/fesh air fan (light duty exhaust fan) with 1.5 Sqmm FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit pipe concealed in the wall with 1.5 Sq. mm FRLSH OVC insulatyed multistrand copper cponductor cable as earthwire drawn inside the conduit.

Wiring Point for call bell with 1.5 sq.mm FRLSH PVC insulated multistrand single core copper conductor cable in PVC conduit pipe concealed in the wall with 1.5 Sq. mm FRLSH OVC insulatyed multistrand copper cponductor cable as earthwire drawn inside the conduit.

Add for light/fan points with modular type switch in place of piano type switch.

Add for 2 Way light point with modular switches in place of piano type switches.

Add for plug point with modular switch & socket in place of piano type switch & socket.

Supply & burying of 40mm dia X 4.5m long G.I. pipe vertically for earthing having 12mm dia holes spaced 75mm apart drilled upto 2metre from the bottom complete with earthing lead of No. 6 to 8 SWG GI wire in GI Pipe upto appron (and from appron to switch board the cost of G.I. wire and pipe will be extra) upto switch board , 30cm Square C.I. box with hinged cover masonary enclosure,funnel at top,alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per direction of E/I complete in all respects as per drwaings.

S&F of 6Amp to 32 Amp. SPMCB (10 KA) C Curve CAT A

S&F of 63Amp. 4 pole Isolator CAT A

S&F surface/flush mounting 12ways SPN distribution board with additional metal door without MCB complete in all respect,as Direct by E/I CAT A

Supply & Fixing of power plug with 20 Amp./250volt Flush type modular switch and 5 Pin 20A/250volt Flush type universal modular socket switch on concealed M.S box including supply of all material,labour T&P etc. required for proper completion of work.

Supply & Fixing of G.P. Modular switch box for 1 / 2 module of approved make made up of 1.0mm thick ISI marked G.P. sheet including adjestable nakka and holes plugged with PVC nylon caps. Two or more holes for pipe entry of 25.4mm on upper & lower sides of the box. Holes should be semi-shuttered type and fitted with heavy brass earth piller duly screwed & brand name should be embossed. Box fklushed in wall including cutting of brick work,fixing it to the level with cement sand mortar,including matching colour wash with s/o all materials,labour and T&P required for proper completion of work as directed ast the site By E/I.

Same As in PWD item no. 1152(A) but for 4 Module.

Same As in PWD item no. 1152(A) but for 6 Module.

Same As in PWD item no. 1152(A) but for 8 Module.

K G CONSTRUCTION

M/S A.G. ENTERPRISES