Repair and Maintenance Work Arrangements at Rajaji Park Division Office in Ward No 31 Zone II Madurai Corporation

Amount

Picking the Existing damaged Clean removal of cement plaster from walls and racking out joints 20mm deep

Dismantling, clearing away and carefully stacking materials useful for reuse for any thickness of walls Asbestos cement sheets roofing without roof timbers

Dismantling, clearing away and carefully stacking materials useful for reuse for any thickness of walls Brick / stone masonry in Cement mortar walls,add for every additional 3 m or part thereof over the initial height of 3 metre

Dismantling Floor finish and dadooing walls in Cement Mortar with mosaic tiles/ glazed tiles/ cuddapah slabs etc Complete

Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel, stoney earth and earth mixed with small size boulders SS.20B and Sand, silt or other loose soil, wet sand, silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering and baling out water wherever necessary refilling the sides of foundation with excavated soil other than sand in layers of 15cm thick well rammed and completed, cleaning and levelling the site etc.,complete - Open Earth Work excavation

Supplying and filling in foundation and basement with filling sand in layers of not more than 15cm thick well rammed watered and compacted - etc., complete complying with standard specification.

Plain Cement concrete 1:4:8 (one cement, four sand, eight aggregate) using 40mm gauge hand broken granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15cm thick and compacted, etc., complete complying with standard specfication.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation - Plinth Beam

Centering for soffits of RCC slabs of plane surface like lintels, beams ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X 3mm laid over silver Oak (C.W) joists of size 10cm X 6.5cm (spaced at about 90cm c/c )and supported dy casurina props of 10cm to 13cm dia (spaced of 75cm C/C) complying with standard specification and directed - For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. - For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

Reinforced Cement concrete 1:1.5:3 (one cement, one and half sand & three course aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc., complete and also including fixing fan clamps and fixtures in rcc works wherever necessary as directed by departmental officer etc., complete (Foundation & Basement)

Reinforced Cement concrete 1:1.5:3 (one cement, one and half sand & three course aggregate) using 20mm gauge hand broken/ and broken granite stone for all RCC items of works excluding centering shuttering and cost of reinforcement but including curing etc., complete and also including fixing fan clamps and fixtures in rcc works wherever necessary as directed by departmental officer etc., complete- Ground Floor

Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors as per standard specification.

Brick work in CM 1:5 (one cement & Five sand) using II class ground moulded bricks of size 9"X43/8"X 23/4" standard specification including finishing, curing, etc., complete complying with standard specification (Masonry projections wherever necessary for obtaining required elevation shall be done without extra cost) - Ground Floor

Brick Partition walls in CM 1:3 (one cement & three sand) using II class ground moulded bricks of size 9"X43/8"X23/4" using hoop iron reinforcement 2 Nos of 6mm dia M.S.rod at every three alternate layers and the cost shall inclusive of iron reinforcement, Brick work etc, complete as per standard specification - Ground Floor

Supplying, fabricating and fixing inposition of Alumi. Anod. natural colour matt finish door half glazedand half PLB board using 12mm thick PLB board and 5.5mm thick glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al.Clips, Best double action floor springs, Aluminium Handles on both sides, floor stopper, Tower bolt ,Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi. surface must be anodised with matt finishund erelectrically controlled condition inaccordance with IS specification 1868/1962 of Anodic fil thickness of not less than 15Microns (Fifteen) for all sections.

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from unplasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 sqm 8313.00 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug

Specification: Supplying and fixing UPVC (Un-PlasticizedPolyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with G1/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energyloss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Plastering with cement mortar 1:5 (One cement and five sand) 12mm thick in all floors including cost and conveyance of all materials to site etc,complete as per standard specifications

Paving the floor with Vitrified Marbonite tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3(one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305mm x 305mm x 6mm in all floors over a base layer of cement mortar1:3 (one cement and three sand) 20 mm thick laid in-situ and pointed with same coloured cement Colour

Plastering with cement mortar 1:3, 20mm, thick in all floors mixed with red oxide including cost and conveyance of all materil as to site and labour charges etc, complete as per standard specifications (S.I.306)

White washing One coats using freshly burnt shell lime, in all floors, including cost of White cement and other materials such as brushes, kanjee, scafolding charges etc. Complete.

Painting two coats of newly plastered wall surface with ready mixed exterior emulsion paint of first quality and of approved colour over a priming coat including preparing the surface, clean removal of dirt and including necessary plaster of paris putty wherever required etc., complete complying with standard specification.

Providing two coats of damp proof putty over the wall surface to levelling the undulation in the walls of approved make. The rate including cost of putty, sand paper and labour

Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC concealed light point / Fan point (For Electronic regulator). etc, complete as per standard specifications. SD 23

Supply and fixing of AC Ceiling fan complete 1400mm 56" Ceiling Fan High Speed (Without regulator) etc Complete

Supplying and Fixing for 18W 4 Feet LED fitting with LED including Labour Charges Etc Complete

Supplying and Fixing for LED OUTDOOR FITTINGS (LIGHT EMITTING DIODE) 48W LED Street Light Fitting with LED

Supplying, fabricating, erecting and fixing Hilux (or) Equivalent Board false ceiling upto a ceiling height of 4.5m from floor level

Supplying and Fixing for 18W LED 3000K Round Type Recessed Fitting with LED etc Completed

Supptying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm "P" or "S" trap connecting with Cl pipe of 100mm dia / PVC pipe of 11omm dia, double flapped rigid PVC black seat and seat cover wilh CP brass hinges including cost of while cement, @ment for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 liters capacity PVC I 12.5 lilets capacity porcelin low level flushing tank with a pair of Cl brackets, etc., complete with all fittings such as 'lsmm brass ball valve with polythene float wilh brass handle, union, coupling connected by means of 40mm white PVC flush hand using lndian adopter joint including all internal

Supply and delivery and Iixing of HDPE tank as per lS 12701 / 1996including loading,unloading, transportation and labour charges for fixingof the Gl pipes and specials for pipe connection works including cutting, lhreadino and flxino charoes elc.. (1000 Litre Capacity)

Supply of PVC Pipe and Specials etc Complete 32mm CPVC Pipe

32mm CPVC Coupler

32mm CPVC Bend

32mm CPVC Elbow

32mm CPVC End Cap

32mm CPVC Tee

32mm Non Return Valve

75mm PVC Pipe

75mm PVC Coupler

75mm PVC Bend

75mm PVC Elbow

75mm PVC End Cap

75mm PVC Tee

110mm PVC Pipe

110mm PVC Coupler

110mm PVC Bend

110mm PVC Elbow

110mm PVC End Cap

110mm PVC Tee

PVC Adhesive (Solution) - 100Gram

40mm GI Pipe

25mm GI Pipe

Supply and Fixing for Roofing with Galvanised Coruugated Iron Sheet of 0.8mm thickness - 10 m2

Add GST 18%

C SATHIYASEELAN (BID ID -1221704)