SPECIAL REPAIRS TO BLDG No. T-143 (OR LIVING) OF DIV CAMP, SPECIAL REPAIRS TO BLDG No. T-69 (RATION STORE, WASHERMAN AND BARBER SHOP) OF SUP PL ASC AND PROVN OF CERTAIN REVENUE WORKS AT DIFFERENT LOCATION OF LIKABALI MIL STN UNDER GE 872 EWS

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Work or Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Dismantling Timber Scantlings 40 Sq Cm and Over in Section in Unframed Work, Seggregating Serviceable Timber Scantlings and keep in Safe Custody for Refixing, complete all as specified and as directed.

Dismantling Timber Fillets, Rails, Posts, Rafters, Purlins, etc. Under 40 Sq Cm in Section in Unframed Work, complete all as specified and as directed. NOTE : Taking down/ out of Forking Pieces fixed with Scantlings, etc. will not be Measured separately for Payment.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) of any description, exc. 1.50 Square Metre but not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, Segregating the Serviceable Steel Sheeting, stacking properly at Sites and keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Demolition of Reed, Lathing, Single or Double including Battens and Plaster or Chicken Wire Lathing (One Side only measured in cases where both Sides are Plastered) and removing Debris, etc. etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Hacking/Taking out Broken Glass of any description from Wooden or Metal Frames, or Stone, Concrete or Brick surrounds of any thickness or size; Hacking out Old Putty or Removing Beads, etc., complete all as specified and as directed,

Taking up or down Steel Tubing 15mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Taking up or down Steel Tubing 20mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Surface Dressing not exc. 15 Cm deep and getting out in Soft/Loose soil, complete all as specified and as directed.

Surface Excavation not exc. 30 Cm deep and ave. 15 Cm deep and getting out in Soft/Loose soil, complete all as specified and as directed.

Excavation in Trenches not exc. 1.50 Metre wide and not exc. 1.50 Metre in depth for Foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in depth and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering and Well Ramming in layers not exc. 25 Cm, in Soft/Loose Soil, complete all as specified and as directed.

Removing Excavated Materials (Soils) not exc. 50.00 Metre and depositing where directed at a level not exc 1.50 Metre above the Starting Point, complete all as specified and as directed.

Excavating in Post Holes (or Similar Holes) in Soft/Loose Soil, each not exc. 0.50 CUM, getting out and removing surplus Soil to a distance not exc. 50.00 Metre and Making Good Surfaces, complete all as specified and as directed.

M&L Sand Filling under Floors or in Foundations in layers not exc. 15 Cm thick including Watering and Consolidation, complete all as specified and as directed.

M&L Hardcore broken Stone or Boulders, gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 Cm thick, watered and well rammed to a True surface, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded aggregate) in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork shall deem to be included in the Quoted Unit Rate.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) in Coping, Bed Plates, Benching, Bed Block, Kerb Stones, etc. including necessary Formwork and Weathering, slightly Rounded or Chamfered Angles and Throating, complete all as specified and as directed. NOTE : Cost of Formwork shall deem to be included in the Quoted Unit Rate.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Foundation including Rafts, Footing, Foundation Beams for Column Basement Slab, under Reamed Piles, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Beams, Cantilevers, Bressumers, Lintels over 1.50 Metre Span, etc., complete all as specified and as directed. NOTE : Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Formwork to Sides of Concrete Foundations, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of Foundation and Plinth Beams; and Similar Work; Vertical or to Batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunchings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Pre-cast Cement Concrete 1:3:6 (20mm graded stone aggregate) Block Masonry with Solid Blocks, exc. 10 Cm in Width, Setting in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work Half Brick thick with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan to any Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Cutting Holes in Brick Walls, not exc. Half Brick thick, built in Cement Mortar for inserting of Holdfasts, Lugs, etc. and Making Good to dismantled portion with Cement Concrete 1:3:6 (20mm graded stone aggregate) or Cement Mortar 1:3 (as required) and adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) in Scantling, Cleansawn, Timber fixed (Unframed work), fixing with Nails, complete all as specified and as directed.

M&L Refixing only Second Class Hardwood (well seasoned) in Scantling (except Scantlings, Serviceable Timber Scantling obtained from Item No. 1.003 here-in-before), Timber fixed (Unframed work), fixing with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Fillets, Plain on One Side, Square, Rectangular or Triangular in Section, exc. 13 Sq Cm but not exc, 25 Sq Cm (Studs of size 50x50mm), fixed with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain, Solid, Straight, Chowkats and Frame, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue pinned at Joints, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Factory Made Panelled Shutter 35mm thick (any number Panels) Plain, Framed with Lock Rails, having Panels of 12mm thick Veneered Particle Board medium density, Wood Particle Board with Commercial Face Veneers and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 35mm thick, Open rebated and prepared to receive Glass, Gauze, etc. (without Sash Bars), Edges of Framing plain, chamfered or rounded. fitted with cut and mitred Beads for securing glass, etc.; sizes of Members of Shutters as specified in SSR Part I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed and Skeleton Shutter 30mm thick, Open rebated and prepared to receive Glass, Gauze, etc. (without Sash Bars), Edges of Framing plain, chamfered or rounded. fitted with cut and mitred Beads for securing glass, etc.; sizes of Members of Shutters as specified in SSR Part I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

M&L Taking down Shutter of any description, not exc. 1.0 Square Metre Each and Refixing in the Same Opeing including necessary Resecuring, or Easing & Adjusting, etc., complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt of size 125mm long (as approved), Extruded Section, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt of size 150mm long (as approved), Extruded Section, complete all as specified and as directed.

S&F Aluminium alloy, anodised, Sliding Door Bolt 300mm long (as approved) with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of size 75mm (as approved), complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of size 100mm (as approved), complete all as specified and as directed.

S&F Aluminium Handle of size 125mm (as approved), anodised, Fabricated type, complete all as specified and as directed.

S&F Aluminium Handle of size 150mm (as approved), anodised, Fabricated type, complete all as specified and as directed.

S&F Floor Door Stopper with Overall length of Cover Plate 150mm of Aluminium Alloy Body and Tongue (as approved) anodised, with Hard Drawn Steel Spring, fixed in Floor, complete all as specified and as directed.

S&F Mild Steel 300mm, Ordinary Rat Tail Rod pattern Springs including Roller and Roller Plate and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Curtain/Harrison Rails or Drapery Road having 24mm Outer dia and thickness 0.8mm (mimimum), fixing with and including Brackets, Stops, Rollers, Side Holders, etc. and Fixed-in-repairs, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples and Fixing-in-repairs, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

S&F Steel Windows with Side Hung Shutters including Projecting type Hinges with Steel Handle and Steel Peg Stay, complete with Glazing Bars, dovetailed or welded, complete all as specified and as directed.

S&F Steel Windows with Side Hung Shutters including Projecting type Hinges with Steel Handle and Steel Peg Stay, complete without Glazing Bars, dovetailed or welded, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes including Bolts, Hooks (Stay) for large Gates; Hook and Pintle Hinges: large Hasps and Staples; Hand Made Sliding Bolts; Clamps; Holdfasts; Wall Ties and similar small Articles conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

M&L Rolled Mild Steel in Joist, Channel, Angle, or Tee Sections in Vertical Post, conforming to Fe-410-W (Gde E-250) Quality 'B', fixed independently, without Connecting Plates, etc. (cut to ordinary lengths i.e. within 20mm of the Length indicated), complete all as specified and as directed.

M&L Rolled Mild Steel Sections in Main and Cross Beams, Hip & Jack Rafters, Purlins where connected to Common Rafters, Running Rails and Guides for Sliding Doors, conforming to Fe-410-W (Gde E-250), Quality 'B', fixed with Angle Cleats or other Connecting Plates, complete all as specified and as directed

M&L Rolled Mild Steel Sections in Roof Trusses (Framed), Trusses, Purlines, Crane Gantries, Rails and Fastening and Heavy Bracket Framing (Beam, Tee, Angle, Channel or Flat Sections) including Distance Pieces, Cleats, etc, welding or riveted, conforming to Fe-410-W (Gde E-250), Quality B, complete all as specified and as directed.

M&L Plates (Plain or Chequered) Channels, Square cut or notched (Ordinary and Counter Sunk) forming Holes, without any attachment, conforming to Gde Fe-410-W (Gde E-250) Quality 'B', complete all as specified and as directed.

S&F Corrugated Mild Steel Sheeting 0.63mm thick, Galvanised @120 Gram Per Sqm, with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

M&L Refixing Galvanised Corrugated Mild Steel Sheeting 0.63mm thick (Serviceable Steel Sheets obtained from Item No. 1.007 here-in-before) with Two Corrugation Side Lap, fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Plain Mild Steel Sheeting 0.80mm thick, Galvanised @ 120 Gram Per Sqm, in Ridges, Hips, Valley Gutters, etc., fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Exposed Suspended False Ceiling System having Snap Grid/ Frame Work of size 605x605mm with and including Hangers 4.0mm dia GI (upto 1200mm length) for adjusting Level, fixed to Roof Slabs by means of Ceilling Cleats made out of GI Flat 40x3.0mm in size, 60mm long and Expansion Hold Fasteners 12.5mm dia, 40mm long, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 4.0mm thick, Pre-primed, Self Embossed, Textured Designer Boards, Water Resistant, Termite Resistant, Fire Resistant for insulation, fixed or laid/ inserted to Snap Grid Frame Work with Screws, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 75mm thick in Sub-base to Floors, etc., complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) 40mm thick in Flooring, etc., laid in Alternate Panels, finished Concrete Surfaces Even and Smooth with using Extra Cement, complete all as specified and as directed.

M&L Plastic Dividing Strips 38x1.5mm thick and inserted in Position, conform to Design, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 25mm thick in Sub-base for laying of Tiles, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick, Joint Free (Square/ Rectangular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick, Joint Free (Square/ Rectangular), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality) in Vertical Surfaces i.e. Dado, Skirting, etc., set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick, Joint Free (Square/ Rectangular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm (1st quality) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-Skid Ceramic Coloured Tiles 7.0mm to 8.0mm thick, Joint Free (Square/ Rectangular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm (1st quality) in Vertical Surfaces i.e. Dado, Skirting, etc., set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Glazed Ceramic Coloured Tiles 350x250x7.0mm or 450x350x7.0mm thick (1st quality) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) 75mm thick in Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without using Extra Cement, complete all as specified and as directed.

M&L Machine Pressed Rubber moulded Pre-cast Concrete Coloured Glossy Finished, Interlocking Polished Paver Block 60mm thick of M-35 Grade, with Grey Cement and Pigment of any shape and size (as ordered), conforming IS-15658-2006, ISI Marked, laid Dry over and including Sand Cushioning of 40mm thick and grouted with Clean dry Sand as in Floors, complete all as specified and as directed. NOTE : Cost of Sand will deemed to be included in the Quoted UNIT RATE.

M&L Rendering (Internal) 15mm thick in Cement Mortar 1:6 on Brick Works/ Pre-cast Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (External) 15mm thick in Cement Mortar 1:4 on Brick Works/ Pre-cast Blocks or Concrete Works, mixing with WPC (if ordered), finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid saperately under appropriate Item.

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion (as approved Tint) over a Coat of Chalk Whitening (Priming Coat), complete all as specified and as directed.

M&L Preparing Old Treated Plastered Surfaces of Walls and applying One Coat of Distemper Oil Emulsion (as approved Tint), complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (as approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Old Treated Surfaces on Walls and applying One Coat of Cement Based Paint (as approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint), complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, not exc. 10 Cm in Width or Girth when unconnected with other Painting or when Painted in different Tint and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of as approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, over exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing Old Treated Steel and Iron Surfaces of any descriptions, over exc. 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade), complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of Wood and Wood Based Materials, of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Backs of Chowkats, etc. Area tarred exc. 0.10 Sqm but not exc. 0.50 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Holdfast or similar Small Items, Area tarred not exc. 0.10 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

Supply & laying Steel Water Tubing 15mm bore (dia), Galvanised, ‘medium grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other situation, complete as all specified and as directed.

Refixing old Steel Tubing 15mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from Item No. 1.013 here-in-before) in New or Old Position (Walls, Ceiling, Floors, etc.) including Cleaning both Inner and Outer Surfaces of Pipes by using Wire Brush including provision of New GI Fittings/ Connections (as required ordered at Sites), complete all as specified and as directed.

Supply & laying Steel Water Tubing 20mm bore (dia), Galvanised, ‘medium grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other situation, complete as all specified and as directed.

Refixing old Steel Tubing 20mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from Item No. 1.014 here-in-before) in New or Old Position (Walls, Ceiling, Floors, etc.) including Cleaning both Inner and Outer Surfaces of Pipes by using Wire Brush including provision of New GI Fittings/ Connections (as required ordered at Sites), complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia) Cast Copper alloy, Chromium Plated, with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and Fixed-in-repairs, complete all as specified and as directed.

S&F Stop Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down carefully Copper/Aluminium Point Wiring (Light, Fan, Socket or Power) complete from in any Position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets but excluding Light Fittings of any description, Making Good Disturbed Surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/ Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down unserviceable Sub-main Wiring from Batten/ Conduit/ PVC Casing Capping of any description, Making Good disturbed surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including providing Surface Treatment (White/Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN/ BELL POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire for ONE 3/5 PIN SOCKET 6 AMP POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded single core Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Sub-main Wiring with 2-Runs of 4.0 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable and 1-Run of 2.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuty Conductor drawn through and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc., complete all as specified and as directed. NOTE :- (a) Cost of 3-Runs of Cables & 1-Run of PVC Casing Capping shall deem to be include in the Quoted Unit Rate and the same will be Mesured as ONE UNIT (b) Sub-main Wiring will be measured PVC Conduit only. Wires required for looping, etc. as ordered will deem to be include in the Quoted Unit Rate.

S&F PVC Rectangular Block/ Board Closed Recessed of size 100x100x50mm deep with 3.0mm thick Plastic Laminated Sheet Cover including Taking down/ out unserviceable Block/ Board of any description, complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Socket Outlet 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 6/16 Amp, 3 Pin, 2-in-1, Multi Plug, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Lamp Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and connecting up, complete all as specified and as directed.

S&F Ceiling Fan Regulator, Dimmer Switch type, 230 Volt AC, Rotary Stepped Electronic, 120/280 Volt including necessary Connection and connecting up, complete all as specified and as directed.

S&F LED Adore 10 Watt, B22 Ball Lamp Decorative Wall Light Fixture made of Polycarbonate, 6500K, suitable for 10 Watt LED Bulb including Taking down Unserviceable Lamp of any description, complete all as specified and as directed. MAKE : HAVELLS, CAT No.: LHLDEUEEML8R010 or equivalent in Make : BAJAJ/ CG/ PHILIPS (as approved by GE).

S&F Decorative Ultra Slim Squre Profile LED Lighting Fixture with Extruded Polycarbonate, Enviromental Friendly, Energy Efficient Ready 18 Watt LED 6500K, connecting up with and including suitable size Twisted Flexible Copper Conductor Cable from Ceiling Rose to Light Fitting including Taking down /out Unserviceable Light Fitting of any description, complete all as specified and as directed. MAKE : HAVELLS, CAT No. LHEXBTP7IN1W018 or equivalent in Make : BAJAJ/ CG/ C&S/ PHILIPS (as approved by GE).

M&L Taking down Ceiling Fan of any Make/Model/Sweep from any Height after disconnecting Electric Connection and Keep in Safe Custody for Re-hanging/ Re-fixing, complete all as specified and as directed.

M&L Hanging/Fixing only Ceiling Fan and connecting with and including suitable size Copper Conductor Cable from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB, complete all as specified and as directed.

S&F Isolator TPN, 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB, complete all as specified and as directed.

S&F Factory Made MCB Distribution Board Sheet Metal Enclosure 4-way, TPN, 240 Volt, Single Door, Front Openable, fixed Flush with Wall inside the Nitches or Outside on Wall Surface suitable for mounting Isolators & MCBs, suitable for Bus-bar 200 Amp rated capacity and connecting up including Taking down/out unserviceable MCB DB, complete all as specified and as directed. MAKE : HAVELLS/ LEGRAND/ L&T/ SCHNEIDER (as approved by GE)

S&F Factory Made MCB Distribution Board Sheet Metal Enclosure 8-way, TPN, 240 Volt, Single Door, Front Openable, fixed Flush with Wall inside the Nitches or Outside on Wall Surface suitable for mounting Isolators & MCBs, suitable for Bus-bar 200 Amp rated capacity and connecting up including Taking down/out unserviceable MCB DB, complete all as specified and as directed. MAKE : HAVELLS/ LEGRAND/ L&T/ SCHNEIDER (as approved by GE)

Supply & Laying or Passing through Pipe 1100 Volt grade heavy duty, Cross-sectional area 10 Sqmm, 2 Core, Flat or Circular Cable with PVC insulated Aluminium Conductor served with an inner sheathing of PVC Tape armoured with Galvanised Steel Wire or Tape and Overall PVC sheathed in Service Connection suspended by insulating Hangers not more than 1.0 Metre apart including 4.0mm Suspension Wire including Taking down/ out Unserviceable Service Connection, complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) Light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing including Taking down/out unserviceable Earthing of any description, complete all as specified and as directed.

M H KHAN

M/S. NOBIN RAJKHOWA

M/S Raju prasad

D. D. Construction

FREEZCON