Construction of CC Road at Bedla Badgon 40ft. Link Road.1004

Item Code [2025 11.4]:Item Type [road] ::Sub Item Code [2025 11.4 + I(i)]: Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and MoRTH specifications Clause 1702, 1703, 2102 & 2104 P.C.C grade M 10 Nominal mix 1:3:6

Item Code [2025 5.8 type A (ii)]:Item Type [road] :: Mix Seal Surfacing Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using Viscosity grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per MoRTH Specification Clause 508 By Mechanical Means Type A Bitumen (VG-30)

Item Code [Rd-2025 BM 5.3.2]:Item Type [road] :: Providing and laying bituminous macadam with hot mix plant using crushed aggregates of grading as perTable500-7 premixed with bituminous binder, transported to site with all lead laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per MoRTH Specification Clause 504 Bitumen (VG-30

Item Code [Rd-2025 prime coat 5.1.1]:Item Type [road] :: Providing and applying primer coat with bitumen emulsion (SS-1)on prepared surface of granular base (WBM/WMM) including cleaning of road surface and spraying primer at the rate of 0.70-1.0kg/sqmusing mechanical means as per MoRTH Specification Clause 502

Item Code [road 2025 4.6]:Item Type [road] :: Providing ,laying , spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (PugMill), carriage of mixed material by tipper to site ,laying in uniform layers in sub-base/base course on a well prepared sub- base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting ,barricading and maintenance of diversion ,etc as per Tables 400-12&400-13 and MoRTH Specification Clause 406. By Mechanical Means with all lead

Item Code [UR2026 3.8(iii)]:Item Type [road] :: Excavation in Ordinary Rock using Hydraulic Excavator and Tippers with disposal upto 1000 m :Excavation for roadway in ordinary rock with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, transporting to embankment site with a lift upto 1.5 m and lead upto 1000 m, trimming bottom and side slopes in accordance with requirements of lines, grades and cross-sections as per MoRTH Specification Clause 301.3.5

Item Code [UR2026 6.1]:Item Type [road] :: Cement Concrete Pavement :Construction of un-reinforced , plain cement concrete pavement M30 (Grade), thickness as per design, over a prepared sub base, with 43/53 grade cement as per Clause 602.2.2 , coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a in fully automatic Batching Plant and transported to site in transit mixer for having continous agitated mixer, manufactured as per approved mix design including pumping of R.M.C. from transit mixer to site of laying , with all lead and lift including cost of admixtures in recommended portion as per IS 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer in charge laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using Fixed Form Paver and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days using water finishing to lines and grade as per drawing and MoRTH Specification Clause 602 including vaccum dewatering process with all required equipments (Dowel Bars will be paid seprately).