Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Status |
|---|---|---|
| 1 | Admitted-Finance | Admitted-Finance |
Tender Value
₹48.2 L
EMD Value
₹96,466
Closing Date
11 Sept 2023, 5:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Chief Executive Officer, Danapur Cantt
Office of the Cantonment Board Danapur Cantt
Construction of Shops at vacant B-4 land near Baldeva Inter School, Sadar Bazar, Danapur Cantt
2023_DGDE_615270_1
CBD/JE/Shops_BHE/2023-24/
Open Tender
Civil Works
Works
240 days
Office of the Cantonment Board Danapur Cantt
As per tender documents
8 documents required · 8 mandatory
₹5,000
Chief Executive Officer, Danapur Cantt
₹96,466
15 Sept 2023
23 Aug 2023
13 Sept 2023
24 Aug 2023
11 Sept 2023
24 Aug 2023
Amount
FOR FOUNDATION & SITE PREPRATION : CHAPTER : 1 EARTH WORK
SSR II-03011: Surface dressing n exc 15 cm deepSoft and loose soil
DSR-20.3: Boring with hydraulic piling rigs with power units, providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) :300 mm
DSR-20.6: Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing. Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge: DSR-20.6.3Group of two or more piles upto 50 tonne Safe capacity
DSR-20.6.3.1: Initial test (Test Load 2.5 times the Safe capacity)
DSR-20.6.3.1: Initial test (Test Load 2.5 times the Safe capacity)
SSR II-03019: Sand filling under floors or in foundations including watering and consolidation
SSR II-03047: Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area
SSR II-03049: Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface
SSR II-03050: Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area
SSR II-03051: Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall
SSR II-03052: Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete
CHAPTER : 2 CONCRETE WORK
SSR II-05040: Damp proof course to horizontal or vertical surfaces including necessary formwork
SSR II-05041: Applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m
DSR-4.17: Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.
SSR-11- 04008 :Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, upto plinth M-15
CHAPTER : 3 REINFORCEMENT WORK
SSR II-10034: Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clipsThermo Mechanically Treated bars.
SSR II-04053: Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete M25
CHAPTER : 3 FORMWORK TO CONCRETE
SSR II-07004: Formwork to sides of concretefoundations, footings, bases ofcolumns, raft and raft beams,sides and soffits (if any) offoundation and plinth beams;and similar work; vertical or tobatter
FOR SUPERSTRUCTURE CHAPTER : 3 REINFORCEMENT WORK
SSR II-10034: Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clipsThermo Mechanically Treated bars.
SSR II-04058: Columns, pillars, piers, posts and struts M25
SSR II-04057: Beams, cantilevers, bressummers, lintels over 1.5m span M25
CHAPTER : 3 FORMWORK TO CONCRETE
SSR II-7014: Formwork to sides of pillars,posts, struts,piers,columnsand stanchions
SSR II-07021: Formwork to edges of concreteflats, treads, breaks in floors,window cills, concrete rail ings, openings in concretewalls, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls, horizon tal or sloping and similarwork exc 10cm but n exc 20cmwide
CHAPTER : 4 BRICK WORK
SSR II-05019: Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in Modular bricks in cement mortar 1:6
SSR II-05020: Brickwork with flyash bricks, straight or curved on plan to any radius i n half brick thick walls, built inModular bricks in cement mortar 1:4
CHAPTER : 5 STEEL WORK
SSR II-10065: Steel rolling shutters, with out ball bearing, as specified including top cover, an choring rod, hasp and staple and one shop coat of primer; erected in position as indi cated, complete: gear operated type with bevel gear box and crank handle
SSR II-10068: Providing and fixing ball bearing for rolling shutters.
SSR II-10046: Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc
CHAPTER : 6 FLOORING
SSR II-13122B: Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;
CHAPTER : 7 ROOFING
DSR-21(12.1.3)Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required0.63 mm thick with zinc coating not less than 275 gm/ m²
CHAPTER : 8 FINISHING
SSR II-14001: Rendering 10mm thick on fair faces of brick work or concrete sur faces. SSR II -14007: All as in item 14001 but 12mm thick-1:6
SSR II-14001: Rendering 15mm thick on fair faces of brick work or concrete surfaces. SSR II -14004: 15mm 1:4 (1 cement: 4 coarse sand)
SSR II-15014D: Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work
SSR II-15014F: Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
SSR II-17029: Synthetic Enamel Paint for two or more coat on surfaces of any description, over 10cm in width or girth,not otherwise described including preparation on new surface On steel work
stage.html
html • 0.02 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .