Customization of Furniture for Hi Tech Breeding Laboratory by Way of High End Counters With Fume Hood Along with Allied Works at COTS Mirgund, SKUAST-K.

Providing in place of main table with overall size of table equal to 1200 x 600 x750mm. The table is made of 25 mm thick Prelaminated Twin Board of E1-P2 grade edge banded with matching 2mm thick PVC lipping. Grommet provided on work surface for wire manaement. The modesty panel is made of 25 mm thick Prelaminated Twin Board of E1-P2 grade. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. The HInge door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. Handles are provided for ease of opening. Pedestals are provided with lock for security.

Providing and fixing of mid-back revolving chair: The seat assembly shall be made up of 1.2 ± 0.1 cm thick hot-pressed plywood and shall be upholstered with fabric upholstery covers and moulded polyurethane foam. The dimensions of the seat shall be 47.0 cm (W) × 48.0 cm (D). The back assembly shall be made of powder coated (DFT 40-60 microns) tubular frame of diameter 2.54 ± 0.03 cm × 0.2 ± 0.016 cm thick MS ERW tube, designed with contoured lumbar support for extra comfort. The back shall be upholstered using net fabric with high tenacity yarn. The dimensions of the back shall be 46.5 cm (W) × 60.5 cm (H). The HR polyurethane foam shall be moulded with density 45 ± 2 kg/m³ and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The one-piece armrests shall be injection moulded from black co-polymer polypropylene. The mechanism shall be designed with 360° revolving type, 17 ± 2° maximum tilt with pivot at centre, upright position locking, and tilt tension adjustment. The pneumatic height adjustment shall have an adjustment stroke of 11.0 ± 0.3 cm. The bellow shall be 3-piece telescopic type and injection moulded in black polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal shall have a pitch-center diameter of 66.3 ± 0.5 cm (76.3 ± 1.0 cm with castors). The twin wheel castors shall be injection moulded in black nylon. The overall dimensions of the chair shall be seat height minimum 43.3 cm to maximum 54.3 cm, height minimum 93.5 cm to maximum 104.5 cm, width 76.3 cm, and depth 76.3 cm as measured from the pedestal.

Providing, supplying and placing of wall side Table with electrical trunking -12850mmL x 750 mm D x 900 mm H with accessories and fumehood with Exhuast The table and storage should be made of MS CRCA (as per the standards of SEFA 10, which is pre-treated thorugh a 9 Tank cleaning process along with Pure Epoxy Powder Coating,the table must comprise of D-Frames, Horizontal members and all cover panels (back, side, leg) and worktop should be Jet black granite 20+- 2mm, the granite must be placed on a neo-prene mat of 6mm thickness, and the joint must be filled using masking tape and silicon sealant. table should have maximum number of Welded storages of 2 Shutters and One drawer. The table should have continuous electrical trunking with 2 nos of 6/16 A switch sockets in every two feet. Table should have 3-way water faucet 1 Nos & pp sink 1 Nos 4 FEET BENCHTOP ABP FUME HOOD Airflow monitor for Fumehood.Eco Panel (2 Hp) With Tl/ Bl For Fumehood.LED LIGHT FOR 4 TO 6 FT FUMEHOOD.3 Module Plate With Socket & Tiny Trip For Fume Hood.Apparatus Grid For 4 Feet Benchtop Fumehood (Epoxy).Raw Water (Flexible Tubing Service Valves For Benchtop Fumehood) (RHS).Compressed Air (Flexible Tubing Service Valves For Benchtop Fumehood) (RHS) Nitrogen (Flexible Tubing Service Valves For Benchtop Fumehood) (RHS).Ceiling Front Cover Panel For 4 Feet Fumehood.Ceiling LH/ RH Side Cover Panel For Fumehood"MOBILE APPARATUS STORAGE CABINET FOR BENCH TOP FUME HOOD WITH FRAME BASED UNDERSTRUCTURE.540W".FRAME BASED UNDERSTRUCTURE FOR 4 FEET BENCH TOP FUMEHOOD WITH NO CUT-OUT ON TRUNKING Back Panel Set For Frame Based Understructure For 4 Feet Benchtop Fumehood SIDE PANEL SET FOR FRAME BASED UNDERSTRUCTURE BENCHTOP FUMEHOOD."CENTRIFUGAL BLOWER & ACCESSORIES "Centrifugal Fan with Housing in PP Construction & suitable stand in MS Zinc Plating with Powder Coating.Non FLP Motor: 2 HP 1400 RPM Inlet/Outlet Dia: 350mm Impeller Dia: 400mm CFM: 1000 @ 50 WCMM Static Pressure DB level: 75 Motor make : IE2 (Non FLP), Crompton Greaves/Bharat Bijlee make whichever is available. DB Level: 85 Approx Motor Description: IP55, 3 Phase, 440 Volt , 50 Hz. Weather cover for motor of model PP25 For PP25 Model Anti-Vibration Pads & M10x100 pin type Anchor Fasteners" Blower Weather Cowl (FRP Outlet) & MS Stack Support with required Clamps PP35 12” (300mm) 100% Injection Molded PP Damper with Two Side Flange MODEL NO:DD/02 PP/FRP DUCTING & ACCESSORIES FOR FUME HOOD & SPOT EXTRACTOR EXHAUST Design, supply & Installation of PP-FRP ducting of wall thickness 3mm PPGL + 3mm FRP for sizes up to 500mm Dia, Above 501mm Dia 4mm PPGL + 4 mm FRP shall be used unless otherwise specified. Including clamps, hanging support, all hardwares required to complete ducting

Providing and fixing of Lab Stools with adjustable height and high base. The seat shall be made up of 1.2±0.1cm thick flat plywood with moulded Polyurethane foam and are upholstered with replaceable synthetic leather covers. The dimensions of Seat shall be Diameter 40.0 cm and Adjustments are 360° Revolving type. The back foam shall be designed with contoured Lumbar support for extra comfort. The upholstery shall be available in synthetic leather. The dimensions of Back shall be 45.0 cm (W) covered with polyurethane foam. The HR polyurethane Foam shall be moulded with density = 45 +/-2 kg/m3 and Hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The manual height adjustment shall be very easy to operate with a help of a knob. It should be easily locked at the most comfortable position. The five-prong pedestal shall be fabricated from 0.2 ± 0.02 cm thick HR sheet ( IS : DD 1079/HR ), powder coated ( DFT 40-60 microns ) and shall be fitted with an injection moulded black Polypropylene Hub Cap and 5 nos. twin wheel castors. The Pedestal shall be 55.0±0.5cm pitch-circle-diameter(65.0±-1.0cm with castors), Circular-foot-ring of dia 52.0±0.2cm shall be made up of dia 1.9±0.2 x 0.12±0.0096cm thk MS ERW Tube for foot support in High-base stool.The twin wheel castors shall be injection moulded in Black Nylon. Overall dimensions shall be Width- 65.0cm, Depth- 65.0 cm, Height- 88.0 to 99.5 cm, Seat Height- 67.0 to 78.5 cm.

Providing and fixing of main table for Director Room with overall size of table 1800 x 2100 x 750mm. The main table shall be of size 1800 x 900 x 750mm. The side unit shall be 1200 x 500 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

Providing and fixing High back Executive Revolving Chair for Director Room with adjustable armrest of the following specifications. The Cushioned seat inner be made of injection moulded glass filled poly-amide. Upholstered seat sub-assembly should consist of moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m³, and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The Cushioned back be made of PU Foam with Polypropylene Injection molded Plastic Inner. (HIGH BACK) SIZE: 74.0cm (W) X 74.0cm. (D). 112.0-132.5cm (H) X 44.5-58.0cm SH. The armrest should be having range of adjustments, Height Adjustment in the aluminum arm body, Up down adjustment, Arm top swivel adjustment at any position, Arm top to and fro adjsutment any position and armrest top be made up of high dencsity PU moulded over glass filled poly-amide inner. Mechanism the adjustable tilting mechanism be designed having following features 360° revolving type, forward tilt of sesat and back, upright tilt lock, tilt tension adjustment to be operated in seating position and 3 position tilt limiter. Seat depth adjustment be housed below the seat and integrated with the mechanism with help of Polypropene Seat cover. Seat Depth be adjusted in sitting position. Seat depth adjustment range be of 5.0±0.5 cm.. The mechanism be designed with the following features: 360° revolving type. 3 position locking with anti shock mechanism. Tilt tension adjustment. . The pedestal be made of die-cast aluminium with buffing finish with 5 nos. twin wheel castors. Back Assembly be connected to buff polish die cast aluminum Spine with an Up-Down mechanism assembly. Back Height can be adjusted in sitting position. It can be adjusted in the range of 7.5±0.5 cm.

work.Ducting upto 500mm Dia - wall thickness shall be 3 mm for PP and FRP.- 14 Sqmtr. ( the construction of the table and storage should be as per the material specifications mentioned in the tender specification Document)

Providing and Placing of a vertical filing cabinet. Size of 4 Drawer VFC shall be 1320mm(H) X 470mm(W) X 620mm(D). All the components shall be made of CRCA . It should have 1 Point Locking Mechanism and a Rigid Knock Down Construction. The Top, Side & Drawer Front thickness should be 0.7mm. The Frames, Drawer-inside cover and Side Back Side thickness should be 0.6mm. The Back, Bottom and Drawer thickness should be 0.5mm. Easy to grip Full length Recess Handle shall be integrated into Metal Drawer for easy pull out convenience. There shall be a Snap on type plastic label holder on Drawer Fronts. In addition, 28 ‘Ezee’ / ‘Visa’ files (Foolscap) from front to back of thickness 20mm per drawer can be hanged in VFC. The Centralized locking System shall be provided along with Shooting Bolt Mechanism and 10 Lever Cam Lock. The VFC should have anti-tipping arrangement which ensures that when one drawer is opened for use, it does not allow other drawers to be opened. The High Quality Precision Ball Slide shall be provided with Drawer Load capacity of max 40 kg and UDL for 75,000 cycles (BS). Plain Triangular plate pop should be riveted at the bottom corners for rigidity. Optional Accessories like Drawer Partition and Cradle for hanging A4 file folders front to back should also be available. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10).

Providing and fixing of small Almirah with an overall size of 765mm(W)x440mm(D)x1270mm(H) with welded construction. It should have the shelf thickness of 0.7mm, Back thickness of 0.8mm and all other components shall be 0.9mm thick. These components are made of CRCA ‘D’grade high yield strength as per IS:513. The storwel Minor should have a Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting (3 nos.) which shall have a Uniformly Distributed Load capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10).

Supplying and Placing of 3 seater sofa for Director Room. The overall dimensions of the sofa shall be 2060W x 905D x 855H. The seat should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Supplying and placing of corner table for Director Room. The corner table should be of size 59.9W x 49.8H x 59.9D (cm). The primary material should be particle board. The finish color should be brown.

Providing and placing a 22-seater modular conference table, which should include one head module (1800mm x 850mm x 740mm), eight 2-seater shared modules (1350mm x 600mm x 740mm), and two 1-seater shared modules (675mm x 600mm x 740mm). The eight 2-seater modules would be arranged with four placed side by side on each side of the head module, while the two 1-seater modules would be positioned opposite each other, integrated alongside the 2-seater modules. The table should be provided with all necessary components for assembly, and the installation team would ensure that it is securely placed according to the specified layout in the conference room. The design should feature high-quality materials, such as engineered wood or laminate for the tabletop and powder-coated metal or sturdy wood for the frame, providing durability and a professional aesthetic. An integrated cable management system would be included to maintain a clean and organized workspace. Worktop shall be Made of 36mm thick MDF one side prelaminate board with 0.4mm PVC membrane pressed on to top and having chamfered edge. Plastic ABS access flap is provided for easy access to wires and cables. Work top is available as per layout. The Under-structure consists of mixture of 25mm and 18mm Pre-laminated twin board of E1-P2 grade and approved shade Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile is used for connecting panels together. Modesty panel shall be made of 18mm Thick Pre-laminated twin board of E1-P2 grade Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip provided below work surface to enhance aesthetics. It is made of 0.8mm CRCA as per IS 513,epoxy polyester powder coated. An array of panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60 microns) is used for flow of wires and cables. Provision to mount Anchor Roma 6 module plate is provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component is fitted to pullout audio,video cables onto worktop and connect devices charger to power socket below worktop.

SEAT/BACK ASSEMBLY: The back should be made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat should be made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back foam should be designed with contoured foam lumbar support. The seat should have an extra thick foam on front edge to give comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair. The chair seat & back size should be: HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H) SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density = 45±2 kg/m3 and hardness l

oad 14 ± 2 kgf as per IS:7888 for 25% compression. ARMRESTS : The 3-way adjustable armrest should be made of die-cast aluminium with buffing finish designed with the following features : · Up-Down adjustment–7 steps (7.0 ± 0.5cm range) · It has to & fro movement along with Swivel adjustment. CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism should be designed with the following features: · 360° revolving type. · 3 position locking with anti shock mechanism. · Tilt tension adjustment PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment should an adjustment stroke of 9.5 ± 0.3 cm. PEDESTAL ASSEMBLY : The pedestal should be made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel castor. The pedestal should be 67.0 ± 0.5cm pitch-center dia. (77.0 ± 1.0cm with castors). TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon. WIDTH (W): 77.0 CM. DEPTH (D): 77.0 CM. HEIGHT (H): 110.5-120.5 CM. SEAT HEIGHT (SH): 44.5-54.5 CM

Providing and fixing of revolving chair with headrest: The contractor shall provide and fix revolving chairs with headrests as per the specified design and technical requirements. The seat shall be made of hot-pressed plywood with a thickness of 1.2 ± 0.1 cm and shall be upholstered using net fabric with high tenacity yarn. The seat size shall be 47 cm (W) × 51.5 cm (D). The backrest shall be constructed from injection-moulded glass-filled nylon and upholstered with net fabric with high tenacity yarn. The seat shall include HR polyurethane foam with a density of 55 ± 2 kg/m³ and a hardness of 16 ± 2 kgf as per IS:7888 for 25% compression. The armrest shall be made from plastic injection-moulded nylon with a textured top and an integrated layer of thermoplastic elastomer. The armrest structure shall allow an up/down adjustment of 8.5 ± 0.5 cm. The chair shall feature a front pivot synchro mechanism with 360-degree revolving, single-point control, front pivot tilt, tilt tension adjustment, 4-position locking with anti-shock feature, and a seat/back tilting ratio of 1:2. The lumbar support shall consist of a polypropylene pad with moulded polyurethane foam, covered with polyester fabric, and shall be adjustable in height by 8.0 ± 0.5 cm using two projecting knobs on the rear side. The chair must be Greenguard Certified for low chemical emissions and SCS IAQ Certified for Indoor Air Quality. Additionally, a headrest from the same family shall be provided. All work shall be carried out according to the guidance and instructions from the Engineer In-Charge.

Providing and placing a 65-inch Smart LED TV, which should feature a 4K Ultra HD resolution of 3840 x 2160 pixels and would be equipped with a Smart TV platform such as Android TV or a proprietary operating system to support smart functionalities. The display should be LED, LCD, OLED, or QLED type, offering high-definition viewing quality. The TV should include a minimum of 3 to 4 HDMI ports and 2 to 3 USB ports to ensure adequate connectivity. Built-in Wi-Fi should be provided along with at least one Ethernet port for network access. The unit would also feature inbuilt speakers with a minimum audio output of 20W (e.g., 10W x 2) to deliver clear sound. The TV should be BIS registered and have at least a 1-star BEE energy rating for efficiency. A minimum two-year on-site comprehensive warranty should be included. Additional features such as screen mirroring, Bluetooth connectivity, and accessories like wall mount kits and necessary cables would also be part of the supply, depending on the specific tender requirements.

Providingin place of main table with overall size of table 1650 x 1650 x 750mm. The main table shall be of size 1650 x 750 x 750mm. The side unit shall be 900 x 500 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

Providing and fixing of visitor chair: The seat assembly shall be made up of 1.2 ± 0.1 cm thick hot-pressed plywood, upholstered with fabric upholstery covers and moulded polyurethane foam. The dimensions of the seat shall be 47.0 cm (W) × 48.0 cm (D). The back assembly shall be made of powder coated (DFT 40-60 microns) tubular frame of diameter 2.54 ± 0.03 cm and thickness 0.2 ± 0.016 cm MS ERW tube, designed with contoured lumbar support for extra comfort. The back shall be upholstered using net fabric with high tenacity yarn. The dimensions of the back shall be 46.5 cm (W) × 60.5 cm (H). The HR polyurethane foam shall be moulded with density 45 ± 2 kg/m³ and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The one-piece armrests shall be injection moulded from black co-polymer polypropylene. Th

e powder coated (DFT 40-60 microns) tubular frame shall be cantilever type and made of diameter 2.54 ± 0.03 cm × 0.2 ± 0.016 cm thick MS ERW tube. The overall dimensions of the chair shall be seat height 46.5 cm, height 93.5 cm, width 61.0 cm, and depth 64.5 cm as measured from the pedestal.

Providing and Placing Visitors Chair for Director Room with overall size of 60.9 W m x 64.2 D cm x 98.2 H cm x 44.8 Seat Height cm. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The tubular frame is cantilever type and made of Ø2.54±0.03cm x 0.2±0.016 cm thick SS 202 tube. The back connected to frame through chrome plated high pressure die casted connector pipe.