Beautification and illumination around Shree Sateri Devasthan at Colsoi Kirlapal Dabal Dharbandoda Goa

Amount

CIVIL WORKS

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sq.m on plan) including disposal of excavated earth lead upto 50 m and lift upto 1.5m disposed earth to be leveled and neatly dressed including providing barricading, danger lighting guarding as directed in : a) All kinds of soil

Earthwork in excavation by mechanical means (hydraulic excavator)/manual means in foundation pipeline trenches drain (not exceeding 1.5 m in width or 10 sq.m. on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed within a lead of 50 m. b) All types of Ordinary rock including all types of laterite rock, blasting prohibited

Refilling the pipeline/foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth as directed by Engineer .

Brick work using common burnt building bricks in cement mortar 1:3 (1 cement : 3 coarse sand) with bricks of class designation 40 kg / cm2 (wire cut bricks) In superstructure upto floor five level.

Rubble packing with hard laterite stone under floors including watering ramming and consolidating etc. in pipeline trenches and other foundations complete.

Laterite masonry in neatly dressed stones of size as specified in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and superstructure

Extra for laterite masonry in all sizes in superstructure from floor I level upto floor V level.

Half brick masonry usign fly ash bricks in cement mortar 1:3 (1 cement : 3 coarse sand ) with bricks of class designation 40 kgs / cm2.b) Above plinth upto floor V level

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: a) All work up to Plinth level

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: In retaining walls , return walls(any thk) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping bed blocks, anchor blocks, plain window sills, fillets etc, upto floor five level.

Providing and laying upto floor five level cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm nominal size) including smooth finishing to exposed surfaces, with cement mortar 1:3 (1 cement: 3 fine sand) including centering and shuttering etc. b) String courses, copings, bedplates, anchor blocks, plain window sills and the like.

Providing and laying upto floor five level cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm nominal size) including smooth finishing to exposed surfaces, with cement mortar 1:3 (1 cement: 3 fine sand) including centering and shuttering etc d) Moulding as in cornices, window sills etc. exceeding 15 cm in girth.

Providing and laying in position ready mixed concrete (RMC) with usage of Ordinary Portland Cement manufactured in fully automatic batching plant and transported to site of work in transit mixer for a lead upto 10kms having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work including pumping of R.M.C., from the transit mixer to the site of laying, excluding the cost of centering, shuttering, finishing and reinforcement including the cost of admixtures in recommended porportions as per IS : 9103 to accelerate/retard setting of concrete, improve workability without imparing strength and durability as per the directions of the engineerin-charge. All works upto floor V level a) M-25grade of concrete

Centering and shuttering including strutting, propping, & removal of form for a) Foundation, footings, bases of columns

Vertical surfaces such as retaing walls, return walls, Partitions, walls (any thickness) including attached Pilasters, Buttresses, Plinth and string courses, Fillets and the like

Centering and shuttering including strutting, propping, & removal of form for b) Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders, Bressumers and Lintels plinth beams not exceeding 1m in depth

Centering and shuttering including strutting, propping, & removal of form for c) Columns, Piers, Pillars, Aburments, Posts and struts (square rectangle polygon in plan)

Centering and shuttering including strutting, propping, & removal of form for d) Suspended floors, roofs, landings, shelves & their supports

Centering & shuttering including Strutting, Propping & removal of forms for sloping or battering surface (slabs, beams, louvers, etc) including folded plates Cornices & Mouldings

Extra to be added for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de- shuttering and de-centering at all levels, over a height of 3.5m, for every additional height of 1m or part thereof. (Plan area to be measured) Suspended floors, roofs, landings, beams and balconies (plan area to be measured)

Providing TMT steel reinforcement bars of SAIL, TATA, VIZAG made only (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member. Minimum Grade of Steel - Fe 500

Steel work welded (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only)in built up sections trusses and framed work including cutting, hoisting, fixing in position and applying priming coat of red lead paint. b) In tees, angles, flats and channels

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of approved make (Min Yeild Stress 310 Mpa)) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Providing and fixing M.S. Fan clamp type I or II of 16 mm dia M.S. Bar bent to shape with hook ends in RCC slabs during laying including painting the exposed portion of loop, all as per standard design complete.

Providing and and laying antiskid floor tiles 12 x 12 upto 16 x 16 in of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete a) Dark Shades

Providing and fixing 1st quality ceramic glazed wall tiles (Johnson, Somany, Kajaria )conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @3.3kg per sq.m including pointing in white cement mixed with pigment of matching shade complete. a) Wall Ceramic Glazed Tiles : 300 x 600

Providing & fixing 18 mm thk Flame Finish Granite Tread Tiles in single piece in Jet Black with rounded off nosing, antiskid groove laid on 20 mm (average) thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) with neat cement slurry including pointing with pigmented cement slurry to match the shade of slab, cleaning etc. complete. ( Price range 2000 to 2100 Rs per Sq Mtr.)

Kotah stone slab flooring over 20 mm (average) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) 20 mm thick.

Providing and fixing Granite stone slabs (mirror polished) 18mm thick in risers of steps, skirting, dado and pillars laid on cement paste and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. Jet Black

Providing and laying Polished Granite stone flooring, coping in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. ( Price range 1550 to 1600 Rs per Sq Mtr.)

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design / shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc. shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001: 2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm. c) 80 mm thick in all colours except grey (M40 grade)

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design / shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc. shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001: 2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm.d) 80 mm thick in grey colour (M40 grade)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm a) Jet Black

Providing 25mm thick cuddapah slabs machine cut and polished on either side in partitions including making necessary grooves in the wall and fixing with cement mortar, complete as directed by the engineer.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/Cuddapah stone work, including necessary holes for pillar taps etc.including moulding, rubbing and polishing of cut edges etc. complete.

Supplying and fixing Pre-cast cement concrete kerb-stones(factory made,the factory should be ISO certified and registered under Dirctorate of Industries, Govt. of India) of M-20 with 20 mm nominal size granitic/basaltic aggregate properly consolidated by mechanical plat-form and vibrators with smooth finish including fixing at site complete as per specification. Size 60 cm L x45 cm H x 15 cm T

Providing and laying 300x350x160 mm thick decorative laterite stone flooring (Patradevi stone) laid on 20 mm thick base of cement mortar 1:4 ( 1cement :4 coarse sand ) including maintaining 75 mm gap between two stone for grassing.Gaps to be filled with good earth for grassing. all work completed as per directed by Engineer-in-charge.

Providing water proofing treatment over the new R.C.C. roofs terrace by spreading cement slurry over the R.C.C. slab and laying of 10cms. Average laterite stone ballast coba with the necessary gradient for easy flow of rain water and the coba in covered with damp proof of Hindustan water proofing co. Or equivalent jointless water proofing plaster of mix 1:3 (1 cement: 3 find sand), finished smooth with wooden trowel with false marking of 30 cms square. The vertical surface of the adjoining walls are to be treated upto a height of 30cms including rounding of junction (the rate includes for complete items including labour and materials and including cost of initial treatment of roof slab as follows. The injunction of damp proof or equivalent compound with cement solution will be given as and when found necessary for filling honey comb, cracks etc. in the R.C.C. slabs). NOTE: cement consumption 25 kg/sq.m.

Providing and fixing waterproofing treatment to sanitary blocks consisting of layers of Laterite stone coba of 75 mm thick in cement mortar 1:2 sand witched between two layers of cement mortar 1:4 (20 mm thick ) mixed with water proofing compound, top finishing coat of cement slurry 6 to 12 mm thick with water proofing compound etc. complete with 32 mm dia PVC pressure relief pipe of adequate length including waterproofing treatment to 750 mm height (maximum) of side wall, and bottom surface in cement mortar 1:4 with waterproofing compound and covering 10 years guarantee on court fee stamp of Rs. 100 with ponding test including all lead, lift etc. complete as directed by Engineer.

Providing & Fixing in position Double Skin roof with Zincalume/ Galvalume colour coated & bare profile sheet with subtle square fluting factory cut at all heights for roof, side & Gable cladding complete in all respect. TOP SHEET-The end rib shall be designed for anti-capillary action. The feed material should be manufactured out of nominal 0.45 mm Base Metal Thickness (BMT), Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 43.5% Zinc &1.5% Si) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides) with quality paint coat as per AS/NZS 2728 type 3-4. The paint shall have a total coating thickness of nominal 35 μm, comprising of nominal 20 μm exterior SMP coat on top surface and nominal 5 μm reverse backer coat on back surface over nominal 5 μm primer coat on both surfaces of approved colour shade. Total Coated Thickness (TCT) should be 0.50mm. Total Painted Thickness (TPT) should be in addition to 0.50mm. The steel sheet shall be fastened with nominal 40 μm zinc coated or nominal 25 μm zinc-tin alloy coated, Hex head, self-drilling screw as per AS 3566-2002 Class 3 fasteners of approved make with EPDM washer as per the requirement considering the profile shape and design load. The fastener size shall be calculated as per the design or manufacturers recommendations. The profile sheet, fastener size etc. shall be approved by the Engineer. The sheeting should be with minimum 200mm lap & waterproof with Silicon sealant non-hardening neutral cure type shall be applied at all end laps, complete as directed Z-Sub Girt - roll formed section 50x50x50x1.50 TCT, 120GSM Galvanised, High Strength (345 MPa), approximate Wt. 1.85 kg/r.m. fixed with self tapping screws Glass Wool Insulation with FSK facing 50mm with 24 kg/m3 density in between 2 sheets. LINER SHEET-bare galvalume/zincalume roofing sheet of same profile as top sheet. The feed material is of manufactured out of nominal 0.45 mm Base Metal Thickness (BMT) (0.47 mm TCT), Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 45% Zinc) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides), passivated & resin coated. The feed material should have coil manufacturer’s product details marked at regular interval for confirming genuinity of the material. complete as per the directions of the engineer. The steel manufacturer's test certificate for the chemical & mechanical properties of steel must be submitted for approval prior to installation.

Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including all the accessories (TATA make) but excluding the cost of purlins, rafters, trusses, flashings etc. complete as per the directions of the Engineer in charge.

Add for providing & fixing Flashings -[Corners, Ridges, valleys, gable end & Trims] (Girth upto 610mm) including all the accessories complete as per the directions of the Engineer in charge.

Providing and laying 1st class mangalore tile roof covering with 25 x 50mm (1” x 2”) jamba wood or similar batten including nails etc. but excluding rafters.

Providing and laying ridge tiles laid dry & pointed with lime mortar 1: 2 (1 lime: 2 surkhi)

Providing and fixing Prince or equivalent make PVC SWR half round eaves gutter with bolts, nuts and flat iron brackets 40 x 3 mm size complete. A) 140 mm nominal size

Extra for providing flat iron bracket 50 x 3 mm size instead of 40 x 3 mm size with necessary bolts nuts, washers etc. for fixing A.C. gutters to purlins.

Extra for providing and fixing prince or equivalent make PVC SWR short stop ends for socketed half round eaves gutters. A) 140 mm nominal size

12 mm thick cement plaster 1:4 (1 cement:4 fine sand)

6mm thick cement plaster to ceiling with 1:3 (1 cement : 3 fine sand)

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge.

Extra for providing and mixing water proofing material proportion recommended by the manufacturers. (a)12mm cement plaster 1: 3 (1 cement : 3 sand)

Extra for plastering done on mouldings, cornices, or arch it raves including neat finish to line and level.

Forming & Finishing the 20 mm groove in plastered surface & repair the edges as per specifications and directions of the Engineer In Charge.

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Painting three or more coats with acryllic exterior paint of approved brand and manufacture (such as weather shield,APEX) including applying one coat of cement primer and one coat of surface treatment etc. complete.

Painting (two or more coats) with synthetic enamel paint of approved brand and manufacture in all shade or new work over and under coat of suitable shade with ordinary paint of approved brand and manufacture to give an even shade

Single Colour Foam Core FRP (Fiber Reinforced Polymer) Door Shutter Manufacture, Supply and Installation (including accessories as mentioned below) of EPEE or equivalent Goan make FRP (Fiber Reinforced Polymer) door shutter of specified thickness as per options below by using tray system with seasoned hard wood, moisture less than 17%, wood styles for Top rail and lock rails. FRP (Fiber Reinforced Polymer) laminate made up of 450 grams per sq.mts (gsm) chop strand matt and unsaturated polyester resin with viscosity range of 400/450 centipoises per second (cps) . The core of shutter will be filled as specified (Expanded Polystyrene Foam / Polyurethane Foam (EPS/PU) Foam). The shutter to be of single colour & water proof as well as mild acid / alkali resistant manufactured using RV TIFAC (R V Engineering College, Bangalore & Technology Information Forecasting & Assessment Council) technology in line with IS 13034 1990 test Standard in an ISO 9001 – 2015 certified factory.Accessories:i) S. S. Hinges 4” - 3 Nos ii) S. S. Latch - 1 No iii) Tower Bolt iv) Handle 5” - 2 Nos 5” - 2 Nos Shutter Thickness : b) 35mm

Providing and fixing bright finished brass door latch with necessary screws etc complete. 300x 16 x 5 mm

Providing and fixing chromium plated brass butt hinges with necessary screws etc. complete Size 125 x 70 x 4.0mm

Provided and fixing 150 mm chromium plated brass floor door stopper with rubber cushion screws etc. to suit shutters thickness complete.

Providing and fixing bright finished brass tower bolts (barrel type) with screws etc. complete a) 250 x 10 mm

Providing and fixing bright finished brass tower bolts (barrel type) with screws etc. complete b) 200 x 10 mm

Providing FRP door shutters 35mm thick with frame size in clear opening of 0.75x2.10m hinges and screws complete.,

Demolishing cement concrete 1:4:8 or leaner mix including disposal of material within 50 m lead

Extra for cutting reinforcement bars in R.C.C. or R.B. work

Demolishing laterite stone masonry in cement mortar including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead.

Dismantling G.I. sheets roofing including ridges, hips valleys and gutters etc. and stacking the material within 50 meters lead.

Providing and fixing anodized aluminum ventilators (including frame and shutter ) with three partitions with 5 mm thick approved clear float glass in one partition, Exhaust opening in one partition & 6 mm thk glass louvers in one partition with using weight and size of section not less then as specified or as shown in drawing ,locking arrangement,silicon sealant ,EPDM gaskets, including all aluminum fixture and fittings etc. complete . All gaps between civil work and aluminium frames shall be sealed and made watertight by applying silicone sealant.Rectangular tube @0.478kg/m

Carting away unwanted excavated material such as soil, lime, moorum, building rubbish, laterite stone, Excavated earth, ordinary rock etc. from site lead of 5 km including all loading & unloading charges ( A ) ( by mechnaical Automative Transport ) Contractor should arrange land for dispose up these material at his own cost Lead upto 5 km.

Constructing soak pit 1.20m x 1.20m x1.20m filled with laterite stone aggregate 125 to 180 mm including S.W. drain pipe 100 mm diameter and 1.2m. Long complete as per standard design

Supply, fabrication and installing in position MS gates of required width and height of including wicket gate and Rolling Gate(if necessary) of approved size made of channels joists, angles, plates, pipes and MS sheets including stiffeners, bracing, fabricated hinges, MS aldrops locking arrangement, tempered steel pivots, guide track of MS tee, ball bearing arrangement, casters wheels etc. all complete as per drawing, specification and as directed by Engineering in charge all complete. The main entrance gate shall be fabricated out of Mild steel sections completed with applying a priming coat of approved steel primer and two coats of synthetic enamel painting. The structural steel works for gates shall include supply, fabrication, transportation, erection of structural steel gates complete with placing in position embedded parts in concrete / brickwork and in road surface including cutting, grinding, drilling of holes, welding and painting etc complete

Providing & fixing Below Mentioned Items made in fiber (FRP/GRP/ ANY OTHER MATERIAL SPECIFIED BY VENDOR) alongwith fabricating a rigid skeletal frame work by welding steel bars/weld mesh as per the desired size, shape and profile of the finished structure .Finish should be simillar to the photofeatures approved by the Architect. Rate should be inclusive of Scaffolding , reinforcement welding, framework as per structural design. Work should be as per detail design & drawing and satisfactory of the Architects. a) Theming work for main entrance gate in FRP as per tender drawing

Providing & fixing Below Mentioned Items made in fiber (FRP/GRP/ ANY OTHER MATERIAL SPECIFIED BY VENDOR) alongwith fabricating a rigid skeletal frame work by welding steel bars/weld mesh as per the desired size, shape and profile of the finished structure .Finish should be simillar to the photofeatures approved by the Architect. Rate should be inclusive of Scaffolding , reinforcement welding, framework as per structural design. Work should be as per detail design & drawing and satisfactory of the Architects. b) Theming work for Kalash in FRP as per tender drawing

Construction of Deepstambh of RCC pillar with exposed laterite masonary of octagonal shape (1500mm length of each side and total height of 5500mm) with openings for placing diya lamps and foundation platform of size (1800mm length of each side and height of 1500mm) including molding,etc. as per the detail drawings and as directed by Engineer in charge.

Supplying and stacking of good earth ( Garden Soil) at site including royalty and carriage upto 1 km. (earth measured in stacks will be reduced by 20% for payment).

Rough dressing the trenched ground including breaking clods.

Fine dressing the trenched ground.

Spreading of sludge, dung manure or/and good earth (Garden Soil) in required thickness (cost of sludge, dung manure or/and good earth to be paid separately).

Supply at site of work/store deoiled Neem cake duly packed in used gunny bags as per MoRT & H Specification 308.2

Supplying of sludge duly stacked at site/store as per MoRT & H Specification 308.2

Providing and fixing M.S. flat iron tree guard 60cm dia & 2 m high above ground level, formed of 4 nos. 25 x 6mm and 8 nos. 25 x 3mm vertical M.S. flat iron rings in two halves, bolted together with 8mm dia and 30 mm long bolts including painting two coats with paint of approved brand and manufacture over a coat of priming, complete in all respects.

Filling mixture of earth & sludge or manure in the desired proportion in trenches flooding with water and leveling (cost of supplying earth and sludge of manure and mixing excluded).

Proving and fixing white vitreous china water closet squatting pan (Indian type w.c. pan) size 580 mm with 100 mm sand cast iron P. or S trap 10 litres high level P.V.C. flushing cister (of approved make) with fittings, rack bolts 32 mm diameter P.V.C telescopic flush pipe with fit tings and clamps 25mm P.V.C. over flow pipe with specials & mosquito proof coupling of approved municipal design and nylon pull complete cutting and making good the walls and floors where required. Long pan pattern W. C. Pan

Proving and fixing white vitreous china Wall Hung type (European Type) water closet with seat and lid with C.I. brass hinges and rubber fittings with flush valve nelson/ similar fully chromium plated with stop cock, wall flanges, flush pipe or elbow and vaccum breaker coupling etc. including chair bracket/rag bolts, cutting & making good the walls and floors where required and concealed seat support - W.C. Pan with white plastic seat and lid

Providing and fixing Hand Shower (Health Faucet) with 8mm dia, ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainles steel flexible hose) and wall hook of approved quality confirming to IS standards.

Providing and fixing NICKEL chrome plated copper alloy Fancy Two Way Bib Cock with single knob and wall flange conforming to IS 8931:1993 15mm nominal bore.

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing vitreous china wash basin with RS or C.I. brackets painted white, 15 mm C.P. brass pillar taps C.P. brass chain with rubber plug 32 mm C.P. brass waste of pattern, 32 mm diameter M.I. or C.P. brass trap and union complete, including cutting and making good the walls where required. b) Flat back wash basin size 630x 450mm with a single 15 mm C.P. brass pillar taps.

Providing and fixing NICKEL chrome plated copper alloy Fancy BOTTLE TRAP ECONOMY TYPE 32MM Jaquar make or equivalent. Confirming to IS 8931;1993

Providing and fixing white vitreous china flat back Large lipped front urinal basin of 590x375x390mm size with Urinal Valve Auto closing system with built in control cock & wall flange with fittings, spreader, R.S. or C.I. brackets, standard size C.P. Brassl flush pipe and spreaders with C. P. brass unions & C. P. Brass clamps with waste fitting as per IS 2556, PVC trap with outlet grating and other couplings in CP Brass complete, including painting, fittings, cutting and making good the walls and floors where required. - Range of one urinal basin

Providing and fixing approved make circular below / under counter Wash hand basin - white vitreous china of size 440 x 440 mm including C.P.Piller Tap, 32 mm C.P.Waste coupling, PVC flexible pipe inlet connection and C.P.Wall Flange complete with necessary bolts, bents, tees, brass screws including cutting of granite, making holes in the wall if required and making the surface good to the satisfaction of Engineer.

Providing & fixing liquid soap container with C. P. brass lid and brackets fixed to wooden cleats with C. P. brass screws Plastic container

Providing and fixing brass bib cock (heavy) of approved quality : 15 mm nominal bore

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 including cutting of stone and making good the walls wherever required. Kitchen sink without drain board. with coupling & all accessories complete with choke stop strainer, Plain type having flat borders for correct sandwithing between the plaform top and bottom slabs complete. Overall size 610mmx510mm (24"x20") bowl size 545mmx445mmx200mm (211/2"x 17 1/2"x 8") depth 200 mm. Glossy. 1.0mm thk,

Providing and fixing NICKEL chrome plated copper alloy Fancy Pillar Cock with extended lever handle and wall flange Confirming to IS 8931; 1993 15mm nominal bore

Providing and fixing L Shaped grab bar S.S. 304 L SHAPED DISABLED GRAB BAR of IZE-600MM (H) X 600MM(D)and 32MM DIA. and thickness1.5 mm of the approved brand and make.

Providing and fixing Straight grab bar S.S. 304, Straight SHAPED DISABLED GRAB BAR of IZE-300MM (L) and 32MM DIA. and thickness1.5 mm of the approved brand and make.

Providing & fixing Stainless steel with perforated/plan grating over Nahani trap for wash basins, shower, sinks, etc, with all necessary cutting, filling, fixing & making good the services, etc,complete. perforated/plan cover for wash basins, shower, sinks,etc. - Top grating Size in mm - 100 x 100 (110 mm)

Providing & fixing Stainless steel with perforated/plan grating over Nahani trap for wash basins, shower, sinks, etc, with all necessary cutting, filling, fixing & making good the services, etc,complete. perforated/plan cover for wash basins, shower, sinks,etc. - Top grating Size in mm - 100 x 100 (75 mm)

Providing and fixing nahani trap of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, without door : 110mm

Providing and fixing nahani trap of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, without door : 75mm

Providing and fixing Angular Stop Cock with wall Flangue - Jaquar make. (a)Florentine (FLR-5053N) 15mm of approved quality.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. 15 mm outer dia CPVC pipe

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. 20 mm outer dia CPVC pipe

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. 25 mm outer dia CPVC pipe

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer-in-charge. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. 32 mm outer dia CPVC pipe

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer. Internal work - Exposed on wall. SCH-40(blue)/(white) 25mm outer dia.

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer. Internal work - Exposed on wall. SCH-40(blue)/(white) 32mm outer dia.

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer. Internal work - Exposed on wall. SCH-40(blue)/(white) 40mm outer dia.

Providing and fixing ball valve ( brass ) of approved quality (Low pressure with copper floats) Low pressure with copper floats 25 mm nominal bore

Providing and fixing non-return valve of approved quality : b) 32 mm nominal bore

Supplying at store or site of work including railway freight, carting, loading, unloading, stacking etc. C. I. single large orifice air valve(fig S2confirming to IS 14848/2000 with suitable connections as directed by Engineer -In- Charge for working pressure of 10kg/sq.cm. (Class B) Dia in mm 25 mm

Fixing C.I. Single large orifice air valve of similar make with bronze ferrule at inlet screwed suitable to working pressure of 15kg/sq. cm for 12 mm to 20mm and 10kg/sq. cm for 25mm to 50mm, complete, as directed by the Engineer in-charge, of following sizes. 25 mm

Providing and fixing C.I. Strainers for Water Meters including cost of all materials and labour.C.I. Strainer 'Y' type with screwed ends. 40 MM dia

Providing and fixing R.P.V.C. vent cowl: 110mm

Providing and fixing R.P.V.C. vent cowl: 75mm

Providing at store or site work non-pressure RCC pipes of with collar joints conforming to IS:458-2003 revised as per amendment No.11 , including freight, carting, loading, unloading, stacking etc. complete. I)NP2 Class 150 mm

Providing at store or site work non-pressure RCC pipes of with collar joints conforming to IS:458-2003 revised as per amendment No.11 , including freight, carting, loading, unloading, stacking etc. complete. I)NP2 Class 250 mm

Providing at store or site work non-pressure RCC pipes of with collar joints conforming to IS:458-2003 revised as per amendment No.11 , including freight, carting, loading, unloading, stacking etc. complete. I)NP2 Class 300 MM

Conveying carefully from stack at site, 250m from both sides rolling and lowering into trenches, laying and jointing true to line and level, RCC spun pressure and non-pressure pipes of various classes, specials including collar and perfect linking of joint with jack to correct position including cost of jointing material in cement mortar 1:2, necessary hydraulic testing, curing of cement mortar etc. complete. 150 mm

Conveying carefully from stack at site, 250m from both sides rolling and lowering into trenches, laying and jointing true to line and level, RCC spun pressure and non-pressure pipes of various classes, specials including collar and perfect linking of joint with jack to correct position including cost of jointing material in cement mortar 1:2, necessary hydraulic testing, curing of cement mortar etc. complete. 250 mm

Conveying carefully from stack at site, 250m from both sides rolling and lowering into trenches, laying and jointing true to line and level, RCC spun pressure and non-pressure pipes of various classes, specials including collar and perfect linking of joint with jack to correct position including cost of jointing material in cement mortar 1:2, necessary hydraulic testing, curing of cement mortar etc. complete. 300 MM

Providing and fixing square-mouth S.W. gully trap grade ‘A’ complete with c.i. grating brick masonry chamber and water tight C.I. cover with frame of 300 x 300 mm size (inside the weight of cover to be not less than 4.53 kg). And frame to be not less than 2.72 kg as per standard design : 150 mmx 100mm P or S.type

Constructing brick masonry manhole or inspection chamber with second class bricks in cement mortar 1:5 (1 cement :5 fine sand) R.C.C. top slab with 1:2:4 mix (1 cement: 2 coarse sand ;4 graded stone aggregate 20mm nominal size foundation concrete 1:2:4 mix (1 cement ;2 coarse sand :4 graded stone agrregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cemetn and making channels in cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) neatly finished complete as per standard design. Inside size 60 x 60cm and 60cm deep including C.I. cover with frame (light duty) 455x610mm internal diameter total weight of cover and frame to be not less than 38 kg. (weight of cover 23 kg).

Construction of manhole rectangular in shape including cement concrete 1:3:6 (1 cement:3 coarse sand:6 graded stone aggregate 20mm nominal size) foundation thickness of concrete 20cms and offset 10cms on both sides and first class brick work with bricks class designation 100kg/sq.cm (wire cut bricks) cement mortar 1:3 (1 cement : 3 coarse sand) 23cms thick including providing & fixing CI footrests confirming to IS 5445/69 or revised and whose weight shall not be less than 5.30kgs including fixing in man-hole at 30cm c / c in 20x 20x10cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) and 12mm thick plaster inside and outside with cement mortar 1:3 (1 cement : 3 coarse sand) including adding waterproofing compound of approved brand in cement mortar with a floating coat of neat cement and making channel in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20m nominal size) neatly finished complete as per standard design.Inside size 0.60x0.60m and 0.60m deep (with medium duty DI manhole cover & frame of size 0.60x 0.60m weighing 90kgs ) including fixing with cement concrete 1:2:4 ( 1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size and applying the frame & cover with coal tar.

Providing & fixing c.p. brass towel rail complete with C.P. brass brackets fixed to wooden cleats with C. P. brass screws a) 750 x 20 mm size

Providing and placing on terrace roof of floor two (1st flor roof single piece rotational moulded polythene water storage tank having I S I mark and conforming to I S 12701; 1996. 1000 lit. capacity

Supplying and erecting minimum Three & above star rated 1 phase, 230 V, 50 Hz, submersible pump set of 1.5 KW/2HP suitable for erection on open well, pump having delivery head from 29 to 7 m and discharge from 30 to 600 litres. . per minute & pipe of Suction 50 mm/Delivery 50 mm diameter erected with necessary H type clamps as per specification No. WP-OSP (Domestic/Irrigation water pump)

Supplying and erecting D. O. L. Starter suitable for 250V. single phase, 50 cycles with overload element with necessary materials and connected to supply upto 3 H.P.

Providing and fixing 75 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete

Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete

Providing, laying and fixing P.V.C. pipe of 40mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete

Providing, laying and fixing P.V.C. pipe of 50mm dia. with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete

ELECTRICAL WORKS

Supply ,Installation,Testing & Commisioning of 6 M High Hot Dip Galvanised Octagonal pole with arrangement for erection of Two to Four flood Light fitting along with pole cap of 300 mm length 75-100 mm dia .(Suitable to pole top) duly welded and with foundation bolts having bottom dia. from 135 to 160 mm, top dia. from 65 to 75 mm including foundation, with all required accessories like Junction box with 15A Input output connectors ,provision for 0.5 - 6 A C curve SP MCB for suitable for each light fittings and its termination of cables should be made using with proper lugs ,Pole will Be Painted with P U Paint as per GTDC color choice etc.Complete with all required accessories.Similar to Wipro /Bajaj /PhillipsBajaj/Havells /Suncity /RRISPAT Or equivallent model of specified brand.

Supplying and erecting integrated LED flood light fitting Max. 100W IP65 & IK07 class having pressure die-cast aluminium housing, having system lumens output of Min. 10000 Lumens, min. efficacy of 100 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50, including driver with U shaped bracket & other related accessories .Complete with all required accessories Similar to Wipro/ Baja /PhillipsBajaj /Havells /Jaquar /Suncity /Legero of specified brand.

Supply ,Installation,Testing & Commisioning of 6 M High Galvanised Decorative Conical pole with Decorative Street light bracket for erection of Single fitting made from 40 mm. dia ‘B’ class G.I. pipe 1 m in length along with pole cap of 300 mm length 100 mm dia .(Suitable to pole top) duly welded and with foundation bolts having bottom dia. from 135 to 160 mm, top dia. from 65 to 75 mm on provided foundation, with all required accessories like Junction box with 15A Input output connectors , 0.5 - 6 A C curve SP MCB for suitable for each light fittings 3 Core 2.5 Sq. mm Cu Flex. cable for light fitting from Junction box to Light fittings and its termination of cables should be made using with proper lugs ,Pole will Be Painted with P U Paint as per GTDC color choice etc.Complete with all required accessories.Similar to Wipro /Bajaj /PhillipsBajaj/Havells /Suncity /RRISPAT Or equivallent model of specified brand.

Supply ,Installation,Testing & Commisioning of 6 M High Galvanised Decorative Conical pole with Double Arm Decorative Street light bracket for erection of Double fitting made from 40 mm. dia ‘B’ class G.I. pipe 1 m in length along with pole cap of 300 mm length 100 mm dia .(Suitable to pole top) duly welded and with foundation bolts having bottom dia. from 135 to 160 mm, top dia. from 65 to 75 mm on provided foundation, with all required accessories like Junction box with 15A Input output connectors , 0.5 - 6 A C curve SP MCB for suitable for each light fittings 3 Core 2.5 Sq. mm Cu Flex. cable for light fitting from Junction box to Light fittings and its termination of cables should be made using with proper lugs ,Pole will Be Painted with P U Paint as per GTDC color choice etc.Complete with all required accessories.Similar to Wipro /Bajaj /PhillipsBajaj/Havells /Suncity /RRISPAT Or equivallent model of specified brand.

Supply ,Installation,Testing & Commisioning of LED decorative Street light fitting of 60-80W,including lamp, with PF > 0.95,class IP 65 and above Housing of pressure die cast aluminium alloy and heat sink extruded aluminium Complete with all required accessories .Efficacy =>100lm/W.Complete with all required accessories Similar to Wipro/ Baja /PhillipsBajaj /Havells /Jaquar /Suncity /Legero of specified brand.

Supply ,Installation,Testing & Commisioning of 4.5 M High Galvanised Decorative Conical pole with Decorative Street light bracket for erection of Single fitting made from 40 mm. dia ‘B’ class G.I. pipe 0.6 m in length along with pole cap of 300 mm length 100 mm dia .(Suitable to pole top) duly welded and with foundation bolts having bottom dia. from 125 to 145 mm, top dia. from 65 to 75 mm on provided foundation, with all required accessories like Junction box with 15A Input output connectors , 0.5 - 6 A C curve SP MCB for suitable for each light fittings 3 Core 2.5 Sq. mm Cu Flex. cable for light fitting from Junction box to Light fittings and its termination of cables should be made using with proper lugs ,Pole will Be Painted with P U Paint as per GTDC color choice etc.Complete with all required accessories.Similar to Wipro /Bajaj /PhillipsBajaj/Havells /Suncity /RRISPAT Or equivallent model of specified brand.

Supply ,Installation,Testing & Commisioning of LED decorative Street light fitting of 45W,including lamp, with PF > 0.95,class IP 65 and above Housing of pressure die cast aluminium alloy and heat sink extruded aluminium Complete with all required accessories .Efficacy =>100lm/W.Complete with all required accessories Similar to Wipro/ Baja /PhillipsBajaj /Havells /Jaquar /Suncity /Legero specified brand.

Supplying and erecting 12 W wall mounted LED downlight IP 65 having Extruded and Die cast aluminium housing with high corrosion resistance surface finish with Integral control gear and beam angles - narrow, medium, wide ,Complete with all required accessories .Complete with all required accessories Similar to Wipro/ Baja /PhillipsBajaj /Havells /Jaquar /Suncity /Legero specified brand.

Supplying and erecting 20(10+10) W wall mounted LED UP downlight IP 65 having Extruded and Die cast aluminium housing with high corrosion resistance surface finish with Integral control gear and beam angles - narrow, medium, wide ,Complete with all required accessories .Complete with all required accessories Similar to Wipro/ Baja /PhillipsBajaj /Havells /Jaquar /Suncity /Legero of specified brand.

Supplying,installation,testing,commisioning of LED decorative circular / trapezoidal 18-25 W hanging focus light from surface or ceiling equivalent type Light having provision of hanging and accesories with inbuilt driver, accesories complete as required. Accessories required for hanging shall be part of the fitting (suspension height from ceiling 1.5 meter).Complete with all required accessories Similar to Wipro/ Baja /PhillipsBajaj /Havells /Jaquar /Suncity /Legero of specified brand.

Supply ,Installation of Tree Uplighter with 9W LED lamp complete with Spike, IP65, 24VDC, Suitable watts driver / power supply (if any), connecting wire,.Complete with all accessories and Coated with epoxy zinc phosphate primer and finished using environmentally stable polyurethane based paint .Complete with all required accessories Similar to Wipro/ Baja /PhillipsBajaj /Havells /Jaquar /Suncity /Legero of specified brand.

Supply,Installation,Testing & Commissioning of exterior-rated architectural RGBNW (Red, Green, Blue, Neutral White) LED linear luminaire of 1000/ 1200 mm length having maximum wattage of 15W. Luminaire should Controlled through DMX/Ethernet protocol using Controller, Controller can achieve 16.7M colors or above. Rated input supply of Input Voltage 24V DC. LED Make : CREE / LUMINOUS / OSRAM / Lumen Maintenance 50,000 hrs L50 at 35°C.Luminaire luminous flux of minimum 700 Lm (with all channels on). Luminaire Housing - Extruded aluminum with die-cast aluminum end caps , Finish - Electrostatically applied polyester powder coating , Color - Dark Grey (RAL7012) , Bracket - Cold-rolled steel , Adjustability -Tilting angle ±95° , Lenses -Anti-aging and anti-UV high optical efficiency PMMA lenses, Gasket - Silicon , Cover - Clear tempered glass. Luminaire weight should not be more than 1kgs. The Luminaire should be capable of producing dynamic color changing light by DMX/Ethernet.IP67 male/female connectors for through power+signalconnection. IP protection rating : IP66, impact resistance IK 06. The luminaire should have beam angle of 45°(±10% ).CRI>80, White SDCM<4.Approx dimension 1000 mm x 25.4mm x 71 mm (with bracket). The luminaire should have Operating Temperature: -40°C to +50°C, BIS Certified Mandatory. The fixtures proposed must have passed LM79& LM-80 Reports along with sample from NABL laboratory will be submitted post the issuance of LOA to the successful bidder and before the supply of material.

Supply,Installation,Testing & Commissioning of exterior rated IP67 driver of 150W for power supply

Supply, Laying, Testing and Commissioning of 4Pin DMX Leader cable- Data supply to the first luminaire 4P DMX cable 2m length (10 pc set)

Supply, Laying, Testing and Commissioning of 4Pin DMX Jumper cable- Data supply from luminaire to luminaire 4P DMX cable 2m length (10 pc set)

Supply, Laying, Testing and Commissioning of 5Pin DC/ DMX Leader cable- Power and data supply to the first luminaire 5P DC/DMX cable 2m length (10 pc set)

Supply, Laying, Testing and Commissioning of 5Pin DC/ DMX Jumper cable- Power and data supply from luminaire to Luminaire 5P DC/DMX cable 2m length (10 pc set)

Supply,Installation,Testing & Commissioning of exterior-rated architectural RGBNW (Red, Green, Blue, Neutral White) LED floodlight in rectangular form factor having maximum wattage of 60W. Luminaire should Controlled through DMX/Ethernet protocol using Controller, Controller can achieve 16.7M colors or above. Rated input supply of Input Voltage 220-240 VAC, 50/60Hz ., LED Make : CREE / LUMINOUS / OSRAM / Lumen Maintenance 50,000 hrs L50 at 35°C.Luminaire luminous flux of minimum 3100 Lm (with all channels on). Luminaire Housing - Extruded aluminum with die-cast aluminum end caps , Finish - Electrostatically applied polyester powder coating , Color - Dark Grey (RAL7012) , Bracket - Cold-rolled steel , Adjustability -Tilting angle ±90° , Lenses -Anti-aging and anti-UV high optical efficiency PMMA lenses, Gasket - Silicon , Cover - Clear tempered glass. Luminaire weight should not be more than 4kgs. The Luminaire should be capable of producing dynamic color changing light by DMX/Ethernet.,IP67 male/female connectors for DMX through wiring (DMX versions only) control. IP protection rating : IP66, impact resistance IK 06. The luminaire should have beam angle of 15°(±10% ).CRI>80, White SDCM<4.Approx dimension 293mm x 140mm x 149mm (with bracket). The luminaire should provided with Electrical safety class I, Operating Temperature: -40°C to +50°C, BIS Certified Mandatory. The fixtures proposed must have passed LM79& LM-80 Reports along with sample from NABL laboratory will be submitted post the issuance of LOA to the successful bidder and before the supply of material.

Supply,Installation,Testing & Commissioning of exterior-rated architectural RGBNW (Red, Green, Blue, Neutral White) LED floodlight in rectangular form factor having maximum wattage of 60W. Luminaire should Controlled through DMX/Ethernet protocol using Controller, Controller can achieve 16.7M colors or above. Rated input supply of Input Voltage 220-240 VAC, 50/60Hz ., LED Make : CREE / LUMINOUS / OSRAM / Lumen Maintenance 50,000 hrs L50 at 35°C.Luminaire luminous flux of minimum 2900 Lm (with all channels on). Luminaire Housing - Extruded aluminum with die-cast aluminum end caps , Finish - Electrostatically applied polyester powder coating , Color - Dark Grey (RAL7012) , Bracket - Cold-rolled steel , Adjustability -Tilting angle ±90° , Lenses -Anti-aging and anti-UV high optical efficiency PMMA lenses, Gasket - Silicon , Cover - Clear tempered glass. Luminaire weight should not be more than 4kgs. The Luminaire should be capable of producing dynamic color changing light by DMX/Ethernet.,IP67 male/female connectors for DMX through wiring (DMX versions only) control. IP protection rating : IP66, impact resistance IK 06. The luminaire should have beam angle of 10°(±10% ).CRI>80, White SDCM<4.Approx dimension 293mm x 140mm x 149mm (with bracket). The luminaire should provided with Electrical safety class I, Operating Temperature: -40°C to +50°C, BIS Certified Mandatory. The fixtures proposed must have passed LM79& LM-80 Reports along with sample from NABL laboratory will be submitted post the issuance of LOA to the successful bidder and before the supply of material.

Supply,Installation,Testing & Commissioning of exterior-rated architectural RGBNW (Red, Green, Blue, Neutral White) LED floodlight in rectangular form factor having maximum wattage of 24W. Luminaire should Controlled through DMX/Ethernet protocol using Controller, Controller can achieve 16.7M colors or above. Rated input supply of Input Voltage 220-240 VAC, 50/60Hz ., LED Make : CREE / LUMINOUS / OSRAM / Lumen Maintenance 50,000 hrs L50 at 35°C.Luminaire luminous flux of minimum 1300 Lm (with all channels on). Luminaire Housing - Extruded aluminum with die-cast aluminum end caps , Finish - Electrostatically applied polyester powder coating , Color - Dark Grey (RAL7012) , Bracket - Cold-rolled steel , Adjustability -Tilting angle ±90° , Lenses -Anti-aging and anti-UV high optical efficiency PMMA lenses, Gasket - Silicon , Cover - Clear tempered glass. Luminaire weight should not be more than 2.5kgs. The Luminaire should be capable of producing dynamic color changing light by DMX/Ethernet.,IP67 male/female connectors for DMX through wiring (DMX versions only) control. IP protection rating : IP66, impact resistance IK 06. The luminaire should have beam angle of 30°(±10% ).CRI>80, White SDCM<4.Approx dimension 155mm x 140mm x 149mm (with bracket). The luminaire should provided with Electrical safety class I, Operating Temperature: -40°C to +50°C, BIS Certified Mandatory. The fixtures proposed must have passed LM79& LM-80 Reports along with sample from NABL laboratory will be submitted post the issuance of LOA to the successful bidder and before the supply of material.

Supply,Installation,Testing & Commissioning of exterior-rated architectural RGBNW (Red, Green, Blue, Neutral White) LED floodlight in rectangular form factor having maximum wattage of 24W. Luminaire should Controlled through DMX/Ethernet protocol using Controller, Controller can achieve 16.7M colors or above. Rated input supply of Input Voltage 220-240 VAC, 50/60Hz ., LED Make : CREE / LUMINOUS / OSRAM / Lumen Maintenance 50,000 hrs L50 at 35°C.Luminaire luminous flux of minimum 1250 Lm (with all channels on). Luminaire Housing - Extruded aluminum with die-cast aluminum end caps , Finish - Electrostatically applied polyester powder coating , Color - Dark Grey (RAL7012) , Bracket - Cold-rolled steel , Adjustability -Tilting angle ±90° , Lenses -Anti-aging and anti-UV high optical efficiency PMMA lenses, Gasket - Silicon , Cover - Clear tempered glass. Luminaire weight should not be more than 2.5kgs. The Luminaire should be capable of producing dynamic color changing light by DMX/Ethernet.,IP67 male/female connectors for DMX through wiring (DMX versions only) control. IP protection rating : IP66, impact resistance IK 06. The luminaire should have beam angle of 45°(±10% ).CRI>80, White SDCM<4.Approx dimension 155mm x 140mm x 149mm (with bracket). The luminaire should provided with Electrical safety class I, Operating Temperature: -40°C to +50°C, BIS Certified Mandatory. The fixtures proposed must have passed LM79& LM-80 Reports along with sample from NABL laboratory will be submitted post the issuance of LOA to the successful bidder and before the supply of material.

Supply,Installation,Testing & Commissioning of exterior-rated architectural 3000K LED floodlight in rectangular form factor having maximum wattage of 35W. Rated input supply of Input Voltage 220-240 VAC, 50/60Hz ., LED Make : CREE / LUMINOUS / OSRAM / Lumen Maintenance 50,000 hrs L70 at 35°C. Luminaire luminous flux of minimum 4000 Lm (in 3000K). Luminaire Housing - Pressure die-cast housing, with clear tempered glass, CRI>70, White SDCM<5.Approx dimension 330mm x 210mm x 77mm (with bracket). The luminaire should provided with Electrical safety class I, IP66, IK07,Operating Temperature: -40°C to +50°C, BIS Certified Mandatory. The fixtures proposed must have passed LM79& LM-80 Reports along with sample from NABL laboratory will be submitted post the issuance of LOA to the successful bidder and before the supply of material. Luminaire and driver must be of same make.

Supply,fixing, Testing and Commissioning of end cap male connector (20 pc set)

Supply,fixing, Testing and Commissioning of end cap female connector (20 pc set)

Supply,Installation,Testing & Commissioning of IP20 DMX addressing device for fast and convenient address writing and testing tool for DMX512 luminaires. The device supports internal test animation for DMX512 addresses verification . The device can automatically write address to a whole group of interconnecting luminaires within minutes.Miniature industrial design, compact size and touch screen. It can be powered by a power bank with a Micro-B type USB port for on-site programming and testing after installation.Compact size, Compatible with multiple types DMX512 chips , Built-in test animation effects , SD card slot to store animation and scenes , Supports standard RDM protocol, Supports searching for RDM luminaires and static detection, Color-pick functions ,Can be powered by Micro-B type USB power supply.Input Voltage 6-24V DC , Output Port - 5Ports terminal , Supported Luminaires Types DMX512/RDM.

Supply ,Installation,testing & Commissioning of 4P-DMX Amplifier based on the standard DMX512/RDM protocol and is designed for signal shaping and amplification for long distance transmission for AC luminaires. Signal amplifier supports magnetic isolation protection, protects the controllers and ensures that the DMX signal can be normally transmitted to various luminaires, improving the reliability and stability of the entire control system.Compact design , Low power consumption (1- 2Watt) , Magnetic isolation for signal input and output , DMX512/RDM versions , Rated IP66 for outdoor installation , amplify the signal for up to maximum 100m or Maximum 64 DMX512 luminaires.; Suitable for item no 1. Amplifiers must be supplied along with powersupplies (if required)

Supply ,Installation,testing & Commissioning of 5P-DMX Amplifier based on the standard DMX512/RDM protocol and is designed for signal shaping and amplification for long distance transmission for DC luminaires.Signal amplifier supports magnetic isolation protection, protects the controllers and ensures that the DMX signal can be normally transmitted to various luminaires, improving the reliability and stability of the entire control system.Compact design , Low power consumption (1- 2Watt) , Magnetic isolation for signal input and output , DMX512/RDM versions , Rated IP66 for outdoor installation , amplify the signal for up to maximum 100m or Maximum 64 DMX512 luminaires. Amplifiers must be supplied along with powersupplies (if required)

Supply of 3 core unarmoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 Core 2.5 sq.mm

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 4 Core 4 sq.mm

Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 1/2 Core 35 sq.mm

Supply of 3 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 3 Core 16 sq.mm

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. 4 Core 16 sq.mm

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm in the existing RCC/HUME/STONEWARE Metal pipe, etc. complete as required

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. a) In soily strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. (a) In soily strata

Laying of one number additional PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground in the same trench in one tier horizontal formation including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. a) In soily strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm on surface, etc. complete as required

Construction of manhole rectangular in shape including cement concrete 1:3:6 (1 cement:3 coarse sand:6 graded stone aggregate 20mm nominal size) foundation thickness of concrete 20cms and offset 10cms on both sides and first class brick work with bricks class designation 100kg/sq.cm (wire cut bricks) cement mortar 1:3 (1 cement : 3 coarse sand) 23cms thick including providing & fixing CI footrests confirming to IS 5445/69 or revised and whose weight shall not be less than 5.30kgs including fixing in man-hole at 30cm c / c in 20x 20x10cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) and 12mm thick plaster inside and outside with cement mortar 1:3 (1 cement : 3 coarse sand) including adding waterproofing compound of approved brand in cement mortar with a floating coat of neat cement and making channel in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 graded stone aggregate 20m nominal size) neatly finished complete as per standard design. III) Inside size 0.60x0.60m and 0.60m deep (with medium duty DI manhole cover & frame of size 0.60x 0.60m weighing 90kgs ) including fixing with cement concrete 1:2:4 ( 1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size and applying the frame & cover with coal tar.(Refer Quantity in drawings)

Providing at store or site work non-pressure RCC pipes of with collar joints conforming to IS:458-2003 revised as per amendment No.11 , including freight, carting, loading, unloading, stacking etc. complete. c) 150 mm Dia.NP2 Class

Supplying and laying of 40 mm outside dia. double wall corrugated pipes (DWC-450 N) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Supplying and Installation of couplers without ring for jointing & related all accessories.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 3 x 1.5/2.5 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 4 x 4 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 3 1/2 x 35 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 3 x 16 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. 4 x 16 Sq. mm.

Supply, installation, testing and commissioning of electronic type three phase energy meter (KWh), 4 wire, ISI marked, in polycarbonate or sgheet steel body ( base mounting type) with counter display/LCD display, with ELT, in Class 1.0, 50 Hz, 240 V. AC duly tested by MRT along with Test Certificates, complete as required of following capacity of make L & T only. (b) 10 to 40 A

Supply & ITC of 3 to 6 KVA 3 Phase Unbalanced fan air cooled Static voltage stabilizer with technology of DSP Based IGBT PWM Switching,Input voltage range (V L-L) =320-480 ,Output voltage (V L-L) =400 V ,Output Voltage Regulation = 1% of nominal output voltage,Automatics High & low Voltage cut off input and out put voltage Circuit protections, single phasing preventer/Phase reversal protection,over load & Short circuit protection(Use MCB),Independent Phase Control,LCD /LED Display for regulations mode ,Bypass mode & fault conditions,Automatic bypass: A Fault conditions,Protection Class : IP 20 ,Ambient Temperature : 0 to 45 Degree Celsius ,Wave form Distortion:pure sine wave.

Supplying and fixing following way SPN sheet steel MCB distribution board Consumer Unit 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar hinged front acrylic cover for the MCB knobs detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) (a) 2 + 4 way Cat A

Supplying and fixing following way SPN sheet steel MCB distribution board Consumer Unit 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar hinged front acrylic cover for the MCB knobs detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) (b) 2 + 8 way Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. a) SP, Cat A

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. b) DP, Cat A

Supplying and fixing following rating double pole (single pole and neutral) 240 V RCCB having a sensitivity current upto 300mA in the existing MCB DB complete with connections testing and commissioning etc as required (a) 25 A, Cat A

Supplying and fixing SP blanking plate in the existing MCB DB complete as required.

SITC of Cable Junction Boxes IP 66/67 “weather proof”(Size -155 x 210 x 92 (LXBXH)mm + Cable termination upto 16 Sqmm size.), for outdoor installation(with knockouts for cable entry) with all accessories.

Earthing with GI earth pipe 2 mts long 40 mm dia medium class with ISI mark, of approved brands including accessories and providing masonry enclosure with CI/RCC cover having locking /Lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size not less than 1.0x1.0x 2.0 mtrs(min) and disposal of excavated soil. b) Class B GI pipe, 40mm diameter as per specifications. c) Charcoal/salt as per specs ( paid seperately). d) Refilling the pit of size not less than 1.0x1.0x 2.0 mtrs(min) with soft black soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe . g)watering arrangement(plumbing will be paid seperately). (b) In rocky strata

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/Lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. c)Watering GI pipe, 20mm, Class B, with funnel as per specs. d) Charcoal/salt as per specs ( paid seperately). e) Refilling the pit of size 1.0x1.0x 3.0 mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe.g)watering arrangement(plumbing will be paid seperately). b)In rocky strata

Extra for using salt and charcoal for pipe earth electrode as required( 65 Kgs of Charcoal and 5 Kgs of Salt).

Extra for using salt and charcoal for GI or copper plate earth electrode as required( 96 Kgs of Charcoal and 5 Kgs of Salt)

Supplying and laying 25 mm x 6 mm GI strip at 0.5 m below ground as strip earth electrode including soldering etc. as required

Providing and fixing 25 mm x 5 mm GI strip on surface or in recess for coneections etc. as required

Supplying and laying 6 SWG GI wire at 0.5 m below ground level for conductor earth electrode including soldering etc. as required

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. a) Group B -- with Cat A Modular Accessories

Wiring for group controlled light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable (with)in recessed PVC conduit(heavy) and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the (with) independent recessed PVC conduit(heavy) of appropriate size as required. b) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the (with) independent recessed PVC conduit(heavy) of appropriate size as required. (c) 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit)

Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required. b) 25 mm

Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required. (c) 32 mm(Ground to DB)

Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required (a) 5/6 A switch Cat A

Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required (d) 3 pin 5/6 A socket outlet Cat A

Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required b) 15/16 A switch Cat A

Supplying and fixing following modular switch/ socket on the existing modular plate and switch box including connections but excluding modular plate etc. as required d) 6 pin 15/16 A socket outlet Cat A

Supplying and fixing modular blanking plate on the existing modular plate switch box excluding modular plate etc. as required a) Cat A

Supplying and fixing following size modular GI box alongwith modular base and cover plate for modulator switches in recess etc. as required b) 4 Module ( 125 mm x 7 mm) Cat A

Supplying and fixing following size modular GI box alongwith modular base and cover plate for modulator switches in recess etc. as required (c) 6 Module (200mm x 75 mm) Cat A

Supplying & erecting of LED 9 to 10W tube light fitting (2 feet) with aluminium housing, heat sink, integrated HF electronic driver Complete with all required accessories Similar to Wipro/ Baja /PhillipsBajaj /Havells /Jaquar /Suncity /Legero of specified brand.

Supplying & erecting of LED 20W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver Complete with all required accessories Similar to Wipro/ Baja /PhillipsBajaj /Havells /Jaquar /Suncity /Legero of specified brand.

Supply and erecting of 12 inch (300 mm sweep) exhaust fan with double ball bearings, 1400 rpm, complete with all accessories. (a) Cat A

Supply and erecting of 48 inch ( 1200mm sweep) ceiling fan, double ball bearing type, , complete with all accessories. (b) Cat B

Supply and erecting fan hook box ( 100 mm diameter or equivalent square size, 75mm deep) fabricated out of 16 SWG sheet steel with 10 m round bar hook bounded to RCC steel upto 50 mm length protruding on each side of the box, including painting with 2 coats of red oxide, complete as required.

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required (a) Cat A

One time commissioning and programming. Programing should be provided during execution.

SAIBINI CONSTRUCTION