REPAIR AND REPLACEMENT OF CERTAIN UNSV PARTS OF WOODEN AND STEEL FURNITURE INCLUDING PAINTING AND POLISHING AT GE (S) JAIPUR

Amount

PART A WOODEN FURNITURE

Bed Ply top (FD 246/247)

S&F in repair 12mm thick plywood top BWR Grade ISI Mark approved quality in single piece as per drawing without any joint to the bed frame with sutable screw wood/steel with cup washer including removal of damaged ply wood all as specified on drawing or as directed by Engr-in-Charge

S&F in repairs to Ist quality 2 CHW hard wood long rail 35mm x 90 mm in section as per existing size of Bed including removal of damaged long rail all as specified on drawing or as directred by Engr-in-Charge

S&F in repairs to Ist quality 2 CHW hard wood short rail 35mm x 90 mm in section as per existing size of Bed including removal of damaged short rail all as specified on drawing or as directred by Engr-in-Charge (each short rail will be measured as single unit)

S&F in repairs to Ist quality 2 CHW hard wood support rail in section as per existing size of Bed including removal of damaged support rail all as specified on drawing or as directred by Engr-in-Charge (each support rail will be measured as single unit)

S&F in repairs to head board duly finished with teak face ply consisting of 60x30x260mm vertical size and 30x60x400mm horizontal including legs of size 60x60mm in section at top and legnth 400mm from bottom of leg and 30x30mm in section at bottom complete including removal of damaged head board comlete all as specifed on drawing or as directed by Engr-in-Charge.

S&F in repaires to foot board duly finished with teak face ply consisting of 22x75mm in section hard wood battens 3 nos at eaqual sapce joining top and bottom horizontal rails of foot board. The top and bottom horizontal rails of size 30x60mm shall be Ist quality of 2 CHW hard wood. The vertical legs above horizontal rails shall be 30x60mm complete all as specified on drawing or directed by Engr-in-Charge

M&L tightening of bed ply top with 'L' Bracket made out of MS Steel as to make functional and stable of bed ply top as specified and directed

M&L preparation of wooden surfaces by cleaning scrapping by grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Bed Ply wooden complete all as specified on drawing or as directed by Engr-in-Charge

Bin Multipurpose (FD/E6/MAP/09) Supply and fix after removing following old and unserviceable Part/ Components of Bin Soiled Linen and new parts/ Components of same shape and size, as per existing pattern with glue, bamboo, pins ,screw etc, including tightening of joints. as shown in drawing complete all as specified and directed. Prelaminated particle board shall be 19mm thick, ISI marked, in shade & texture as approved by Engr-in-Charge. Exposed sides of the board to be covered with matching PVC lipping. Teak wood shall be well seasoned, free from pits & knots as per standard drg.Ply wood shall be ISI marked as per standard drg

Side made out of prelaminated partical board

Shelves made out of prelaminated partical board

Drawers made out of prelaminated partical board and bottom of drawing made out of plywood 6mm BWR grade.

Door made out of prelaminated partical board

Top made out of prelaminated partical board

Bottom frame made out of prelaminated partical board

Knobs/Handles as approved

M&L tightening of bin multipurpose as to make functional and stable as specified and directed

S&F teakwood beading duly polished in colour matching the prelaminated board with melamine for glossy finish

M&L preparation of wooden surfaces by cleaining scrapping by grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Bin Multipurpose and as specified and directed by Engr-in-Charge

Chair dining long back (FD-E6/MAP/10, FD-357, TP)

Removing of unserviceable rear leg of chair dinging long back, tighting of loose components S&F new leg made out of Ist class hard wood (SAL/Teak) duly shaped size as per existing and fix with other members carefully by means of Fevicol & Bamboos pins as per shown in the drg

All as per item No 3.01 above but front leg 30mmx40mmx460mm as per drg

All as per item No 3.01 above but verticle back strip as per drg

All as per item No 3 .01 above but front/back/side rail 25mmx65mmx450mm as per drg

All as per item No 3.01 above but stiffeners 20mmx25mmx450mm as per drg.

All as per item No 3.01 above but replacement of suitable PVC shoe duly fixed with 20mm screw

All as per item No 3.01 above but repalcement of unserviceable cushion sheets and S&F foam cushion of 40 density sheet duly covered with long cloth and tapestry cloth on 12mm ply wood BWR as shown in the drg. colour of tapestry cloth as approved by GE of costing not less than Rs 350.00 RM(Approx).

M&L tightening of chair dining long back with 'L' Bracket made out of hard wood as to make functional and stable as specified and directed

M&L preparation of wooden surfaces by cleaining scrapping by grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Chair dining long back and as specified and directed by Engr-in-Charge

Chair Writing (FD-280)

Removing of unserviceable rear leg of chair writing, tighting of lolose components S&F new leg made out of Ist class hard wood (SAL/Teak) duly shaped & size existing and fix with other members carefully by means of synthetic adhesive Fevicol & Bamboos pins as per shown in the drg

All as per item No 4.01 above but front leg as per shown in the drg

All as per item No 4.01 above but for chair writing of back rest as per shown in the drg

All as per item No 4.01 above but stiffener as per shown in the drg

All as per item No 4.01 above but for chair writing of rear rail as per shown in the drg

All as per item No 4.01 above but for chair writing of front rail as shown in the drg

All as per item No 4.01 above but for chair writing of side rail as shown in the drg

All as per item No 4.01 above but removing of exiting unserviceable PVC shoe and S&F new PVC shoe with suitable screw

M&L tightening of chair writiing with 'L' Bracket made out of hard wood as to make functional and stable as specified and directed

M&L Re-canning of Chair writing wooden with plastic cane of 1/2 round 2.0mm wide & 0.40mm thick woven border round and back in Godrej pattern with 4mm side of approved quality (white/cream in colour including removing of old canning compete as as specified and directed

M&L preparation of wooden surfaces by cleaining scrapping by grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces

Chair dining (FD-279)

Removing of unserviceable rear leg of chair dining, tighting of loose components S&F new leg made out of Ist class hard wood (SAL/Teak) duly shaped & size as per existing and fix with other members carefully by means of Synthetic adhesive Fevicol & Bamboos pins as per shown in the drg

All as per item No 5.01above but for front leg as shown in the drg

All as per item No 5.01 above but for front and back rail as per shown in the drg

All as per item No 5.01 above but for side rail as per shown in the drg

All as per item No 5.01 above but for back rest as per shown in the drg

All as per item No 5.01 above but for stiffener as per shown in the drg

All as per item No 5.01 above but replacement of PVC shoe duly fixed with suitable screw

M&L tightening of chair dining with 'L' Bracket made out of hard wood as to make functional and stable as specified and directed

M&L Re-canning of Chair dining wooden with plastic cane of 1/2 round 2.0mm wide & 0.40mm thick woven border round and back Godrej pattern with 4mm side of approved quality (white/cream in colour including removing of old canning compete as specified and directed

M&L preparation of wooden surfaces by cleaining scrapping by grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Chair dining as specified and directed

Chair Easy (FD-229)

Removing of following unserviceable part of Chair Easy, tighting of loose components and supply and fixing new part as mentioned in respective following items made out of Ist class hard wood (SAL/Teak) duly shaped & size as per existing drawing and fixing with other member by synthetic adhesive Fevicol and bamboo pins including french polishing to replaced part of wooden to match with existing part to make serviceable complete all as specified and directed

Front leg of chair easy as per drg

Hand rest of chair easy as per drg

Rear leg of chair easy as per drg

Front/back rail of of chair easy as per drg

Side rail of of chair easy as per drg

Replacement of PVC shoe duly fixed with suitable screw

M&L tightening of chair easy with 'L' Bracket made out of hard wood as to make functional and stable as specified and directed

M&L Re-canning of Chair Easy with plastic cane of 1/2 round 2.0mm wide & 0.40mm thick, woven border round and back Godrej with 4mm wide of approved quality (white/cream in colour) including removing of old canning.

M&L preparation of wooden surfaces by cleaning scrapping by grinder and smoothing of surfaces with sand paper and applying one coat of French poolish on the wooden surfaces of Chair easy wooden.

Hat stand with mirror : (FD-233)

Removing of unserviceable hanging hooks of Hat stand and S&F new hanging MS hooks as per drawing

Replacement of teak ply wood 3/4mm thick WBR grade as per drawing and directed by Engineer Incharge

Replacement of commercial ply wood ISI Mark 6mm thick as per drawing and directed by Engineer Incharge

Replacement of stainless steel Pegs as per drawing and directed

Replacement of Teak wood beading all as per drawing

M&L preparation of wooden surfaces by cleaning scrapping and smoothing of surfaces with sand paper and applying one coat of French poolish on the wooden surfaces of Hat stand with mirror Drg No FD-233

Mirror Dressing (Gents) (FD/E6/MAP/16)

Removing of UNSV mirror and S&F new mirror 5.5mm thick overall size of mirror 600x1200mm (Make : Modiguard), backed by 12mm thick BWR gde plywood covered by decorative mould and supported on 50x28mm hard wood frame all around & as per shown in the drg

Removal of UNSV back ply and S&F new 12mm thick BWR grade ISI Mark ply wood

Removal of UNSV sides and S&F 18mm thick pre-laminted particle board & shown in the drg

Removal of UNSV shelves and S&F new shelves 8mm thick glass shelves supported on glass holder

Removal of UNSV hinges and S&F new hinges continious piano hinges to open the mirror frame in horizontal circle.

Removal of UNSV magnet catch and S&F new magnet catch 02 Nos each at top

M&L preparation of wooden surfaces by cleaning scrapping and smoothing of surfaces with sand paper and applying one coat of French poolish on the wooden surfaces of Mirror Dressing (Gents) Drg No FD/E6/MAP/16

Peg Table (FD-277/384) Removing of unserviceable part of Peg Table S&F new part made out of 1st class hard wood duly shaped as shown in the drg and fixing with other member by means of Fevicol and bamboo pins to make serviceable the item of Peg Table of size as per drg and as directed

All as per item No 9.00 above but for side rail size as shown in the drg and as directed

All as per item No 9.00 above but for legs size as shown in the drg and as directed

All as per item No 9.00 above but for stiffners size as shown in the drg and as directed

All as per item No 9.00 above but for replacement of unserviceable table top with 18mm thick pre-laminated particle board ISI marked with teak wood edging all around.

All as per item No 9.00 above but S&F PVC shoe with suitable screw

M&L tightening of peg table with 'L' Bracket made out of hard wood as to make functional and stable as specified and directed

M&L preparation of wooden surfaces by cleaining scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Peg table and as specified and directed by Engr-in-Charge

Sofa sets 5 seater (3+1+1) (FD-373/FD/MAP-II/02)

Taking down unserviceable leg of sofa set and S&F new leg made of Ist class hard wood duly size and fixed in position as shown in drg.

All as per item No 10.01 replacement of unserviceable front long rail of sofa set (3 seater) and S&F new front long rail of Ist class hard wood all as specified and shown in drg.

All as per item No 10.01 replacement of unserviceable front rail of sofa set (single seater) and S&F new front long rail of Ist class hard wood all as specified and shown in drg.

All as per item No 10.01 replacement of unserviceable rear long rail of sofa set (3 seater) and S&F new rear long rail of Ist class hard wood all as specified and shown in drg.

All as per item No 10.01 replacement of unserviceable rear rail of sofa set (single seater) and S&F new rear long rail of Ist class hard wood all as specified and shown in drg.

All as per item No 10.01 above but for replacement unserciveable side rail and S&F new side rail as specified and shown in drg

All as per item No 10.01 above but replacement unserviceable handrest and S&F new handrest as specified and shown in drg

All as per item No 10.01 above but replacement unserviceable wooden strips of seat & back and S&F new handrest as specified and shown in drg

M&L tightening of sofa set 5 seater (3+1+1) with 'L' Bracket made out of hard wood as to make functional and stable as specified and directed

M&L preparation of wooden surfaces by cleaining scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Sofa set 5 seater and as specified and directed by Engr-in-Charge

Sofa sets 4 seater (FD-281/373)

Taking down unserviceable leg of sofa set 4 seater (single seater x 4) and S&F new leg made of Ist class hard wood duly size and fixed in position as shown in drg.

All as per item No 11.01 replacement of unserviceable front rail of sofa set (single seater x 4) and S&F new front long rail of Ist class hard wood all as specified and shown in drg.

All as per item No 11.01 replacement of unserviceable rear rail of sofa set (single seater x 4) and S&F new rear long rail of Ist class hard wood all as specified and shown in drg.

All as per item No 11.01 above but for replacement unserciveable side rail and S&F new side rail as specified and shown in drg

All as per item No 11.01 above but replacement unserviceable handrest and S&F new handrest as specified and shown in drg

All as per item No 11.01 above but replacement unserviceable wooden strips of seat & back and S&F new handrest as specified and shown in drg

M&L tightening of sofa set 4 seater (single seater x 4) with 'L' Bracket made out of hard wood as to make functional and stable as specified and directed

M&L preparation of wooden surfaces by cleaining scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Sofa set 4 seater and as specified and directed by Engr-in-Charge

Side board (FD-372/341)

Removing of unserviceable top of side board and S&F new top of pre-laminated baord 18mm thick, Teak face, ISI marked as shown in the drg duly polished

All as per item No 12.01 above but bottom of side board as shown in the drg

All as per item No 12.01 above but replacement of unserviceable back of side board

All as per item No 12.01 above but for replacement of Shutter of the side board and supply and fix new shutter with both side pre laminated particle board 18mm thick ISI marked fixed with piano type hinges continuous 20mm.

All as per item No 12.01 above but for replacement of Knobs of chromium plated of approved coloured and standard quality.

M&L preparation of wooden surfaces by cleaining scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Side board and as specified and directed by Engr-in-Charge

Table bed side (FD-276)

M&L Replacement of unserviceable top of table bed side and S&F top of table bed side made out of 18mm pre-laminated particle board ISI marked with 6mm teak wood edging as per drg.

All as per item No 13.01 above but replacement of unserviceable both side of table bed side of 18mm pre-laminated particle board ISI marked with 6mm teak wood edging as per drg.

All as per item No 13.01 above but replacement of unserviceable shelf of table bed side of 12mm pre-laminated particle board ISI marked with 6mm teak wood edging as per drg.

All as per item No 13.01 above but replacement of unserviceable back side of table bed side of 6mm ply wood with 6mm teak wood edging as per drg.

Table Dressing Ladies/Gents/Ladies (MAP) (FD-251, 379, FD/E6/MAP/16)

Removing of existing U/S mirror with ply and both side long rail fitted with the bottom shelf of table dressing ladies and S/F new mirror 5.5mm thick of clear vision with 6mm thick ply fixed at back and both side long rail fitted with the bottom shelf duly polished. (FD-251)

Removing of unserviceable complete bottom shelf (incl legs) of Table dressing ladies and S&F new complete bottom shelf (incl legs made of Ist class hard wood) of pre laminated particle board 18mm thick, Teak face, ISI marked as shown in the drg (FD-251)

Removing of unserviceable Knobs and S&F new Knobs of chromium plated of approved coloured and standard quality. (FD 251, 379, FD/E6/MAP/16)

Repalcement of unserviceable cushion sheets of table dressing ladies stool and S&F new foam cushion of 40 dinsity sheet duly covered with long cloth and tapestry cloth on 12mm ply wood BWR as shown in the drg. colour as approved by GE (FD/E6/MAP/16)

Replacement of swivel type nylon castors and S&F new swivel type nylon castors all as per drg and as directed. (FD/E6/MAP/16)

Removing existing U/S mirror with ply and wooden frame from table dressing gents and S/F new mirror 5.5 mm thick of clear vision (Make : Modi Guard) with 6mm ply on back and wooden frame .(FD-379)

Removal of UNSV shelf of table dressing Gents and S&F new shelf with knobs duly polished. All complete as per drawing and directed (FD-379)

M&L preparation of wooden surfaces by cleaining scrapping and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Table Dressing Ladies/Gents/Ladies (MAP) and as specified and directed by Engr-in-Charge

Table 3' x 2' with / without drawer (FD-283, 284)

Removing of unserviceable part of Table 3' x 2' with/ without drawer, tighting of loose components and S&F new part made out of 1st class hard wood duly shaped as shown in the drg and fixing with other member by means of Fevicol and bamboo pins to make serviceable the item of Table 3'x2' with/without drawer leg of size 760 mm x 60mm x 30mm.

All as per item No 15.01 above but for replacement of Table top of size 3’x2’ with 18mm thick pre-laminated particle board ISI marked with teak wood edging around.

All as per item No 15.01 above but for repalcement of long rail shown as per drg

All as per item No 15.01 above but for replacement of short rail shown as per drg

All as per item No 15.01 above but for repalcement of Middle stiffeners of size 760mm x 40mm x 25mm.

All as per item No 15.01 above but for replacement of Side stiffeners of size 600mm x 40mm x 25mm.

All as per item No 15.01 above but for repalcement of Bottom ply of drawers (commercial ply woods of size 550mm x 310mm x 6mm).

All as per item No 15.01 above but for replacememt of side members of drawer as shown in the drg

All as per item No 15.01 above but for repalcement of ‘L’ type bracket of hard wood 75mm x 75mm x 20mm in table to support rail and leg fixed with screws.

M&L preparation of wooden surfaces by cleaining scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Table 3'x'2 with/without drawer and as specified and directed by Engr-in-Charge

Table dining 6 pers (FD-239, 273, 376 & FD/E6/MAP-II/03)

Removing of unserviceable part of table dining 6 pers S&F new part made out of 1st class hard wood duly shaped as shown in the drg and fixing with other member by means of Fevicol and bamboo pins to make serviceable the item of dining table 6 pers leg of size as per drg and as directed

All as per item No 16.01 above but for replacement of long rail of size 1500mm x 100mm x 25mm.

All as per item No 16.01 above but for replacement of short rail of size 900mm x 100mm x 25mm.

All as per item No 16.01 above but for replacement of Hard wood ‘L’ type bracket made out of hard wood 100mm x 100mm x 25mm fixed with screws

All as per item No 16.01 bove but for replacement of unserviceable table top with 18mm thick pre-laminated particle board ISI marked with teak wood edging all around.

M&L preparation of wooden surfaces by cleaining scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Table dining 6 pers and as specified and directed by Engr-in-Charge

Table dining 4'x3' (FD/E6/MAP/09)

Removing of unserviceable part of table dining 4'x3' S&F new part made out of 1st class hard wood duly shaped as shown in the drg and fixing with other member by means of Fevicol and bamboo pins to make serviceable the item of dining table 4'x3' leg of size as per drg and as directed (FD-273)

All as per item No 17.01 above but for replacement of long rail of size 1200mm x 100mm x 25mm.

All as per item No 17.01 above but for replacement of short rail of size 900mm x 100mm x 25mm.

All as per item No 17.01 4bove but for repalcement of Hard wood ‘L’ type bracket made out of hard wood 100mm x 100mm x 25mm fixed with screws

All as per item No 17.01 above but for replacement of unserviceable table top with 18mm thick pre-laminated particle board ISI marked with teak wood edging all around.

All as per item No 17.01 above, S&F PVC shoe with suitable screw

M&L preparation of wooden surfaces by cleaining scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Table dining 4'x3' and as specified and directed by Engr-in-Charge

Table dining 8 pers

Removing of unserviceable part of table dining 8 pers S&F new part made out of 1st class hard wood duly shaped as shown in the drg and fixing with other member by means of Fevicol and bamboo pins to make serviceable the item of dining table 8 pers leg of size as per drg and as directed

All as per item No 18.01 above but for replacement of long rail of size 1800mm x 100mm x 25mm

All as per item No 18.01 above but for replacement of short rail of size 900mm x 100mm x 25mm.

All as per item No 18.01 above but for replacement of hard wood ‘L’ type bracket made out of hard wood 100mm x 100mm x 25mm fixed with screws.

All as per item No 18.01 above but for replacement of Table top with 18mm thick pre-laminated particle board ISI marked with teak wood edging all around as shown in the drg and as directed.

M&L preparation of wooden surfaces by cleaining scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Table dining 8 pers and as specified and directed by Engr-in-Charge

Table Writing (FD- 275)

Removing of unserviceable part of table writing, tighting of loose components S&F new part made out of 1st class hard wood duly shaped as shown in the drg and fixing with other member by means of Fevicol and bamboo pins to make serviceable the item of Table writing leg of size as per drg and as directed

All as per item No 19.01 above but long rail as shown in the drg as and directed

All as per item No 19.01 abovebut short rail as shown in the drg as and directed

All as per item No 19.01 above but for bottom base of box 18mm thick commercial particle board (ISI marked) as shown in the drg as and directed

All as per item No 19.01 above but side of box 18mm thick commercial particle board ISI marked as shown in the drg as and directed

All as per item No 19.01 above but top with pre-laminated particle board ISI marked 18mm thick with teak wood beading all around as shown in the drg as and directed.

All as per item No 19.01 above but for back ply box 6mm thick commercial ply (ISI marked) as shown in the drg as and directed

All as per item No 19.01 above but for door 18mm pre-laminated particle board of size 380mm x 450mm including knob and hinges piano type scale hinges as specified and directed

All as per item No 19.01 above but for side of drawer hard wood size 450mm x 75mm x 20mm.

All as per item No 19.01 above but for bottom of drawer 6mm thick commercial ply (ISI marked) of size 600mm x 450mm .

All as per item No 19.01 above but for replacement of hard wood ‘L’ type bracket made out of hard wood fixed with screws.

All as per item No 19.01 above, S&F PVC shoe with suitable screw

M&L preparation of wooden surfaces by cleaining scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Table writing and as specified and directed by Engr-in-Charge

Table Centre (FD-274, FD/E6/MAP/09)

Removing of unserviceable part of Table Centre S&F new part made out of 1st class hard wood (SAL/Teak) duly shaped as shown in the drg and fixing with other member by means of synthetic adhesive Fevicol and bamboo pins to make serviceable the item of TableCentre for leg of size as per drg and as directed

All as per item No 20.01 above but long rail size as shown in the drg and as directed

All as per item No 20.01 above but short rail size as shown in the drg and as directed

All as per item No 20.01 above but for replacement of table top made out of 19 mm thick pre-laminated particle board ISI marked with teak wood edging all around as shown in the drg and as directed.

All as per item No 20.01 above but for hard wood bracket ‘L’ type of size 75mm x 75mm x 20mm fixed with screws.

All as per item No 20.01 above, S&F PVC shoe with suitable screw

M&L preparation of wooden surfaces by cleaining scrapping by electric grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Table Centre and as specified and directed by Engr-in-Charge

Teapoy wooden (FD-278, 382)

Removing of unserviceable part of teapoy wooden and S&F new part made out of 1st class hard wood (SAL/Teak) duly shaped & size as existing as shown in the drg and fixing with other member by means of synthetic adhesive Fevicol and bamboo pins to make serviceable the item of teapoy wooden leg of size 540mm x 60mm x 30mm.

All as per item No 21.01 above but side short rail of size 450mm x 50mm x 20mm

All as per item No 21.01 above but long side rail of size 600mm x 50mm x 20mm

All as per item No 21.01 above but ‘L’ type bracket of hard wood of size 75mm x 75mm x 20mm fixed with screws.

All as per item No 21.01 above but Top of teapoy wooden of size 450mm x 600mm x 18mm thick with one side pre-laminated particle board ISI marked with teak wood beading alround all as per drg.

All as per item No 21.01 above but replacement of PVC shoe duly fixed with suitable screw

M&L preparation of wooden surfaces by cleaining scrapping by grinder and smoothing of surfaces with sand paper and applying one coat of French polish on the wooden surfaces of Tepoy wooden and as specified and directed by Engr-in-Charge

TV Trolly (FD/E6/MAP/04)

Replacement of 5.5mm thick plain glass openable glass shutters with magnetic catch and stainless steel pad fitting for glass. All as per drg as directed.

All as per item No 22.01 above but replacement of top of TV trolly with 18mm thick pre-laminated particle board ISI marked of approved shade with 50 x 50mm moulded teak wood beading on 3 sides to shape to be provided all as per drg and as directed.

All as per item No 22.01 above but replacement of swivel type nylon castors wheel all as per drg and as directed.

All as per item No 22.01 above but replacement of both sides of TV trolly with 18mm thick pre-laminated particle board ISI marked of approved to size shape as per existing to be provided all as per drg and as directed.

All as pe item No 22.01 aobve but replacement of decorative handles as per drawing

PART B STEEL FURNITURE

Almirah Large steel (FD-1031)

Taking out old unserviceable existing handle and S&F chromium plated handles including necessary nut, bolts, washer etc for almirah large steel.

Taking out existing shelves and making the same in functioning condition including necessary nuts, bolts, clips and washer etc of almirah large steel all as directed.

Removing existing locking device with MS plate rod and S&F new mild steel body locking device with plate rod complete in almirah large steel as directed.

Taking out old unserviceable lock of Almirah large steel and S&F mild steel body lock with six levers locks and hole cover with duplicate keys.

Taking out old unserviceable leg of almirah large steel and S&F new legs made out of 20 gauge MS sheet made to shape and sizes shown on drawing all as directed.

Taking out of unserviceable door of almirah large steel and S&F new door made out of 1.00mm thick MS Sheet

M&L preparation old painted steel surfaces by cleaning and applying one coat of synthetic enamel paint olive green/grey with spray gun or by manual brush with roller as per requirement in appropriate shade complete all as specified and directed but Almirah large steel with shelves both side (out side and in side)

Almirah steel 1/2 hanging 1/2 shelves (FD/E6/MAP/18)

Taking out old unserviceable existing handle and S&F chromium plated handles including necessary nut, bolts, washer etc for almirah steel 1/2 hanging 1/2 shelves

Taking out existing shelves and making the same in functioning condition including necessary nuts, bolts, clips and washer etc of almirah steel 1/2 hanging 1/2 shelves all as directed.

Removing existing locking device with MS plate rod and S&F new mild steel body locking device with plate rod complete in almirah steel 1/2 hanging 1/2 shelves as directed.

Taking out old unserviceable lock of almirah steel 1/2 hanging 1/2 shelves and S&F mild steel body lock with six levers locks and hole cover with duplicate keys.

Taking out old unserviceable leg of almirah steel 1/2 hanging 1/2 shelves and S&F new legs made out of 20 gauge MS sheet made to shape and sizes shown on drawing all as directed.

Taking out of unserviceable door of almirah steel 1/2 hanging 1/2 shelves and S&F new door made out of 1.00mm thick MS Sheet

M&L preparation old painted steel surfaces by cleaning and applying one coat of synthetic enamel paint olive green/grey with spray gun or by manual brush with roller as per requirement in appropriate shade complete all as specified and directed but almirah steel 1/2 hanging 1/2 shelves with shelves both side (out side and in side)

Almirah medium steel (FD-1032)

Taking out old unserviceable existing handle and S&F chromium plated handles including necessary nut, bolts, washer etc for almirah medium steel.

Taking out existing shelves and making the same in functioning condition including necessary nuts, bolts, clips and washer etc of almirah medium steel all as directed.

Removing existing locking device with MS plate rod and S&F new mild steel body locking device with plate rod complete in almirah medium steel as directed.

Taking out old unserviceable lock of Almirah Medium steel and S&F mild steel body lock with six levers locks and hole cover with duplicate keys.

Taking out old unserviceable leg of almirah medium/steel and S&F new legs made out of 20 gauge MS sheet made to shape and sizes shown on drawing all as directed.

Taking out of unserviceable door of almirah med steel and S&F new door made out of 1.00mm thick MS Sheet

M&L preparation old painted steel surfaces by cleaning and applying one coat of synthetic enamel paint olive green/grey with spray gun or by manual brush with roller as per requirement in appropriate shade complete all as specified and directed but Almirah med steel with shelves both side (out side and in side)

Bed Hard Steel (FD/E6/MAP/08)

Removing of existing unserviceable ply wood 12mm from bed hard steel and S&F new plywood BWR Phenol bounded commercial plywood with edging 1950mm x 900mm ISI Mark all as per Drg and directed.

Supply and fixing and replacing of unserviceable Head rest (with leg and particle board complete) and S&F new Head rest (with leg and particle board 19mm complete) as per drg

Supply and fixing and replacing of unserviceable foot rest (with leg and particle board complete) and S&F new foot rest (with leg and particle board 19mm complete) as per drg

Removing U/S old long rails and supply and fix new long rail MS tubular pipe size 1920x 65 x 25mm ISI marked required as per drg

Removing U/S middle stiffnere and supply and fix new middle stiffnere duly ISI marked required as per drg and directed

M&L elect welding to Bed Hard Steel where required and filling properly at places of welding point. Elect welding shall be done all round the MS pipe and all welding and filling at one broken point shall be measured as one point ie one unit.

Painting with Synthetic enamel black paint inside & out side after scrapping of rusted paint complete as per drg all as specified and directed

Removing U/S PVC Shoes of Bed Hard Steel and supply and fix new PVC Shoes of Bed Hard Steel required as per drg and directed

Chair Writing steel with Arm (FD/E6/MAP/12)

S&F seat and back 12mm, teak ply with poly urethane foam 50mm thick moulded with density 40 with Raxine of approved colour and shade including taking out old unserviceable seat and back complete all as specified & directed . Note :- Seat and/or back shall be measured seperately as each uint.

Replacement leg as specified in the drawing and as directed by Engr-in-Charge

Replacement of arm rest as specified in the drawing and as directed by Engr-in-Charge

M&L dry cleaning of existing seat and back of chair writing steel with arm as directed by Engr-in-Charge

Painting with black paint after scrapping of rusted paint complete by spray gun as per drg all as specified and directed

Chair Writing steel w/o arm (FD/E6MAP/12)

S&F seat and back 12mm, teak ply with poly urethane foam 50mm thick moulded with density 40 with Raxine of approved colour and shade including taking out old unserviceable seat and back complete all as specified & directed. Note :- Seat and/or back shall be measured seperately as each uint.

Replacement leg as specified in the drawing and as directed by Engr-in-Charge

M&L dry cleaning of existing seat and back of chair writing steel as directed by Engr-in-Charge

Painting with black paint after scrapping of rusted paint complete by spray gun as per drg all as specified and directed

Chair School with Hand Board (FD/E6/MAP/05)

S&F seat with back PVC of chair school with hand board with suitable nut & bolt and washer as per drawing and directed, including taking out old unserviceable seat and back of chair school with hand board all as specified & directed. Note :- Seat & back both will be measured as each uint for each chair.

S&F Hand Board of chair school with hand board with suitable nut & bolt and washer as per drawing and directed, including taking out old unserviceable Hand Board of chair school with hand board. Hand board will be made out of prelaminated particle board 19mm thick ISI Mark, size as per drawing and directed.

S&F Wire mesh of chair school with hand board with Gas welding as per drawing and directed, including taking out old unserviceable wire mesh of chair school with hand board all as specified & directed .

M&L Gas welding where required and filling properly at places of welding point and as per directed by Engr-in-Charge

S&F front/rear legs of chair school with hand board with Gas welding as per drawing and directed, including taking out old unserviceable front/rear legs of chair school with hand board all as specified & directed .

Painting with black paint after scrapping of rusted paint complete by spray gun as per drg all as specified and directed

Chair Verandah (FD-256/359M,FD/MAP/11/06)

M&L gas welding to chair verandah where required and filling properly at places of welding point. Gas welding shall be done all round the conduct pipe and all welding and filling at one broken point shall be measured as one point ie one unit.

M&L hard rubber shoe in legs of chair including removal of broken rubber show.

M&L scrapping of surface of chair verandah frame with emery paper making smooth surface and applying one coat of white synthetic enameled paint all as directed.

Removing of old unserviceable Nylong /Cane and recaning of Verandah Chair seat & back with 2.00mm wide and 0.4mm thick plastic cane half round superior quality white or cream colour as approved by Engr-in-Charge

Removing of old unserviceble side leg with arm frame and S&F new side leg with arm frame made 20mm MS cunduct pipe existing gauge 1.60 mm thick as per drg fixing with gas welding

Removing of old unserviceable seat & back combined frame and S&F new seat & back frame made 20mm MS cunduct pipe existing gauge as per drg and fixing with gas welding

Removing of old unservieable front leg stiffener and S&F new front leg stiffener made with 12mm round plain MS Bar as per drg and fixing with gas welding

Chair Computer/Chair Revolving Adj (FD/E6/MAP/01 & TP, PCH-7001(TP))

M&L for removing unserviceable seat and back and S&F new seat & back alongwith the fabric & PVC lipping wherever applicable & replacing the same with new 12mm thick hot pressed phywood upholstered with fabric & moulded polyurethane foam. The back foam shall be designed with contour lumber support with PVC lipping all around. The cushions shall be of 40 density 75mm thick for seat & 50mm thick for back alongwith the fabric of approved quality & colour. All as directed by Engr-in-Charge. Note :- Seat & back will measured each uint in chair.

M& L for removing unserviceable caster wheel and S&F new castor wheels of Chair Computer/Chair Revolving adjustable

M& L for removing unserviceable hand rest of Chair Computer/Chair Revolving adjustable and S&F new handrest of the chairs with new handrest matching the previous all in shape, size, material & quality

M&L for removing unserviceable and S&F pedestal assembly of revolving chairs with new complete pedestal assembly all matching the sape, size & quality of the existing.

M&L for removing unserviceablehydraulic assembly and S&F for servicing the unserviceable hydraulic assembly & making the seat adjustment functional all as directed by Engr-in-Charge

M&L dry cleaning of existing seat and back of chair Computer /Chair Revolving as directed by Engr-in-Charge

Locker steel (FD-1029)

Taking out existing shelves and making in position including necessary elect welding of bed side mild steel body locker steel as directed by Engr-in-Charge

Replacement of old U/S chromium plated handles including necessary nuts and bolts washer etc for bed side mild steel body locker steel

Replacement of old U/S legs of bed side locker by new legs made out of 18 guage MS sheet made to sape and sizes shown on drawing all as directed by Engr-in-Charge

Taking out of unserviceable door of Bed side locker steel and S&F new door made out of 1.00mm thick MS Sheet

M&L preparation old painted steel surfaces by cleaning and applying one coat of synthetic enamel paint olive green/black/grey with spray gun or by manual brush with roller as per requirement in appropriate shade complete all as specified and directed but Bed side locker steel with shelves both side (out side and in side)

Shoe Rack steel (FD/E6/MAP/02/R)

M&L Gas welding where required and filling properly at places of welding point and as per directed by Engr-in-Charge

M&L for painting the frame of the Shoe Rack steel with two coats of synthetic enamel black paint over a coat of primer with the help of spray gun after smoothning the surface with electric ginder complete all as specified & directed

M&L for removing unserviceable and S&F PVC shoes to the legs as applicable complete all as specified & directed

S&F Wire mesh of Shoe Rack Steel as per drawing and directed, including taking out old unserviceable wire mesh of Shoe rack all as specified & directed .

Table Computer (FD/E6/MAP/03)

M& L for removing unserviceable and S&F prelaminated top with new top of prelaminated particle board ISI marked and exposed sides of the board to be covered with matching PVC strip as per drg

M&L for removing unserviceable and S&F prelaminated sides with new side of prelaminated board both side laminated of ISI marked and exposed sides of the board to be covered with matching PVC strip as per drg

M&L for removing unserviceable and S&F prelaminated pullout tray with new tray of prelaminated both side laminated of ISI marked and exposed sides of the board to be covered with matching PVC strip.

M&L for removing userviceable and S&F prelaminated bottom shelf with new shelf of prelaminated board both side laminated of ISI marked & pattern as approved by Engr-in-Charge. Exposed sides of the board to be covered with matching PVC lipping

M&L for removing unserviceable and S&F drawer channels MS suitable size as per existing /Drg with new telescopic channels with smooth run

M&L for painting to all the steel surfaces with spray gun in black color after scrapping off the surface with electric grinder.

M&L for romoving unserviceable and S&F knobs for drawer with new decorative knobs as approved by Engr-in-Charge

M&L for removing unserviceable and S&F PVC shoes to the legs as applicable complete all as specified & directed

Table Bed Side Steel (FD/E6/MAP/15)

M&L for removing unserviceable and S&F back with new back of 18mm thick prelaminated board one side teak face & one side white as approved by Engr-in-Charge ISI marked. Exposed sides of the board to be covered with matching PVC lipping

M&L for removing unserviceable and S&F side with new side of 18mm thick prelaminated particle board both side teak face ISI marked as approved by Engr-in-Charge

M&L for removing unserviceable and S&F top drawer with new drawer of 18mm thick prelaminated particle board one side teak face & one side white ISI marked as approved by Engr-in-Charge. Exposed sides of the board to be covered with matching PVC lipping.

M&L for removing unserviceable and S&F top with new top of 18mm thick prelaminated particle board one side teak face & one side white ISI marked as approved by Engr-in-Charge

M&L for removing unserviceable and S&F bottom drawer with new drawer of 18mm thick prelaminated particle board one side teak face & one side white irrespective of what is shown on drg ISI marked exterior grade as approved by Engr-in-Charge. Exposed sides of the board to be covered with matching PVC liping

M&L for removing unserviceable and S&F knobs for drawer with new decorative knobs as approved by Engr-in-Charge

M&L for removing unserviceable and S&F PVC rubber shoe black color

Removing of unserviceable MS frame of Table Bed side steel and S&F of new MS tubular pipe frame as per drg fixing with elect welding/screw as reqd

M&L preparation old painted steel surfaces by cleaning and applying one coat of synthetic enamel paint black with spray gun or by manual brush as per requirement in appropriate shade complete all as specified and directed by Engr In Charge.

Table office officer/clk (FD-1004,FD-1003)

Taking out old unserviceable lock of drawers of table officer office/ clerk/typist steel and S&F mild steel body lock with four levers locks with duplicate keys.

Taking out existing drawers of table office clerk /officers steel and re-fixing same after necessary setting of drawers for free movement all as directed.

Replacement of Top of table office officers steel with 12 mm thick prelaminated particle board ISI mark with teak wood beadings.

Replacement of Top of table office clk steel with 12 mm thick prelaminated particle board ISI mark with teak wood beadings.

Taking out of unserviceable door shutter of Table office officer steel and S&F new door shutter made out of 1.00mm thick MS Sheet and as per drg

Taking out old unserviceable leg of table office officer/clk steel and M&L legs made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drg.

Taking out old unserviceable front & back long rail of table office officer/clk steel and M&L front rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drg.

Taking out old unserviceable side rail of table office officer/clk steel and M&L front rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drg.

M&L Gas welding where required and filling properly at places of welding point and as per directed by Engr-in-Charge

M&L preparation old painted steel surfaces by cleaning and applying one coat of synthetic enamel paint olive green/grey with spray gun or by manual brush as per requirement in appropriate shade complete all as specified and directed

M&L for removing unserviceable and S&F PVC rubber shoe black color

Table 3' x 3' steel (FD-1009)

Replacement of Top of table 3'x3' steel with 12 mm thick prelaminated particle board ISI mark with teak wood beadings.

Taking out old unserviceable leg of table 3'x3' steel and M&L legs made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drg.

Taking out old unserviceable front & back l rail of table 3' x3' steel and M&L front rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drg.

Taking out old unserviceable side rail of table 3'x3' steel and M&L front rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drg.

M&L Gas welding where required and filling properly at places of welding point and as per directed by Engr-in-Charge

M&L preparation old painted steel surfaces by cleaning and applying one coat of synthetic enamel paint olive green/black/grey with spray gun or by manual brush as per requirement in appropriate shade complete all as specified and directed

M&L for removing unserviceable and S&F PVC rubber shoe black color

Table 3'x2' W/O drawer steel (FD-1007)

Replacement of Top of table 3'x2' W/o drawer steel with 12 mm thick prelaminated particle board ISI mark with teak wood beadings.

Taking out old unserviceable leg of table 3'x2' W/o drawer steel and M&L legs made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drg.

Taking out old unserviceable front & back long rail of table 3' x2' W/o drawer steel and M&L front rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drg.

Taking out old unserviceable side rail of table 3'x2' W/o drawer steel and M&L front rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drg.

M&L Gas welding where required and filling properly at places of welding point and as per directed by Engr-in-Charge

M&L preparation old painted steel surfaces by cleaning and applying one coat of synthetic enamel paint olive green/black/grey with spray gun or by manual brush as per requirement in appropriate shade complete all as specified and directed

M&L for removing unserviceable and S&F PVC rubber shoe black color

Table 3'x2' With drawer steel (FD-1008)

Replacement of Top of table 3'x2' with drawer steel with 12 mm thick prelaminated particle board ISI mark with teak wood beadings.

Taking out old unserviceable leg of table 3'x2' steel with drawer and M&L legs made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drg.

Taking out old unserviceable front & back long rail of table 3' x2' with drawer steel and M&L front rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drg.

Taking out old unserviceable side rail of table 3'x2' with drawer steel and M&L front rail made of square MS tubular pipe 25mm, 1.6mm wall thickness fixing neatly all as directed and as per drg.

Taking out old unserviceable lock of drawers of table 3'x2' with drawer steel and S&F mild steel body lock with four levers locks with duplicate keys.

Taking out existing drawers of table 3'x2' with drawer steel and re-fixing same after necessary setting of drawers for movement and as per drg and directed .

M&L Gas welding where required and filling properly at places of welding point and as per directed by Engr-in-Charge

M&L preparation old painted steel surfaces by cleaning and applying one coat of synthetic enamel paint olive green/black/grey with spray gun or by manual brush as per requirement in appropriate shade complete all as specified and directed

M&L for removing unserviceable and S&F PVC rubber shoe black color

Table dining OR (FD-165)

Taking out unserviceable top of table dining OR and S&F new Top of table shall be of size 72” x 24” excluding beading. 19mm thick prelaminated particle board ISI Mark with teak wood beadings.

Taking out old unserviceable leg of table dining OR and M&L legs made of square MS pipe 25mm, 1.6mm wall thickness fixing neatly all as directed.

Taking out old unserviceable existing centre stiffeners/long rail of table dining OR and supplying and fixing new one made out of 25mm x 25mm square MS pipe of 1.6mm wall thickness as shown on drawing and directed.

Taking out old unserviceable side stiffener, short rail of table dining OR supply and fixing new one made of 25mm square conduit MS, 1.6mm wall thickness as shown on drawing and directed.

M&L Gas welding where required and filling properly at places of welding point and as per directed by Engr-in-Charge

M&L preparation old painted steel surfaces by cleaning and applying one coat of synthetic enamel paint olive green/black/grey with spray gun or by manual brush as per requirement in appropriate shade complete all as specified and directed

M&L for removing unserviceable and S&F PVC rubber shoe black color

Teapoy Verandah (FD-255)

S&F Top made out of 18/19mm pre-laminated particle board ISI marked incl teak wood beading around as per drawing and directed

Removing of old unserviceble leg and S&F new leg made out of 20mm MS cunduct pipe as per drg fixing with gas welding

M&L spot welding by gas welding throughout in broken joints of frame of teapoy verandah complete all as specified & directed. .

Painting of Teapoy Verandah with white paint after scrapping of rusted paint complete by spray gun as per drg all as specified and directed

M&L for removing unserviceable and S&F PVC rubber shoe black color

Teapoy Verandah steel (FD/E6/MAP/17)

S&F Top made out of 18/19mm pre-laminated particle board ISI marked incl teak wood beading around as per drawing and directed

Removing of old unserviceble leg and S&F new leg made out of 20mm MS cunduit pipe as per drg fixing with gas welding

M&L spot welding by gas welding throughout in broken joints of frame of teapoy verandah steel complete all as specified & directed.

Removing of old unserviceble base tray frame and S&F new base tray frame made out of 5mm MS bar as per drg fixing with gas welding

Painting of Teapoy Verandah steel with black paint after scrapping of rusted paint complete by spray gun as per drg all as specified and directed

M&L for removing unserviceable and S&F PVC rubber shoe black color

SK INDUSTRIES

M/S Shri Balaji Enterprises