Agumentation work at CIPLA Laboratory second floor at IISER Pune

Amount

Please Note that quoted rates are inclusive of all taxex,levies,duties,labour,transportaion etc. nothing extra shall be paid separtely.

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of enamal primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 74 mm overall thickness partition with 12 mm thick double skin tapered edged Calcium Silicate Boards. Quoted rate shall be including material , labour, scaffolding , lead , lift , fees towards sample testing , GST , royalties , wastage etc complete. Nothing extra shall be paid seperatily.One side area of partition fixed at site shall be measured for payments.

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. For Supports above false ceiling upto to supprot structure.

Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with ecommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process. Quoted rates shall be including removal of old damaged false ceiling GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron). Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly. Approved Make JINDAL/BARUKA/Indian Aluminium Co.For fixed portion : Powder coated aluminium (minimum thickness of powder coating 50 micron).Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) .Powder coated aluminium (minimum thickness of powder coating 50 micron). Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly. Approved Make JINDAL/BARUKA/Indian Aluminium Co : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots/Sliding and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly.

Providing and fixing glazing in aluminium Door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly. (Cost of aluminium snap beading shall be paid in basic item): With heat strengthen toughen glass panes of 8 mm thickness.Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness. Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly. APPROVD MAKES HAFLE/HETTICH/DORMA

Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly. Approved Makes Godrej/Dorma/Hafle

Providing and fixing Stainless Steel H handle of 300mm size etc. complete pair of in-out handle as per direction of Engineer-incharge. Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly. Approved Makes Godrej/Dorma/Hafle

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : Old work (one or more coats) Ceiling Painting.Quoted rate shall be including at taxes , duties , royalties , lead, lift , trasportation , insurance , GST , etc. Nothing extra shall be paid seperatly. Approved Makes Nerolac/Dulux/Asian.

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.Quoted rate shall be including at taxes , duties , royalties , lead, lift , trasportation , insurance , GST , etc. Nothing extra shall be paid seperatly. Approved Makes Nerolac/Dulux/Asian.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre.Minimum 2 coats .Quoted rate shall be including at taxes , duties , royalties , lead, lift , trasportation , insurance , GST ,etc. Nothing extra shall be paid seperatly. Approved Makes Nerolac/Dulux/Asian.

Wall painting with synthetic enamel paint of satin finish/ Acrylic emulsion paint approved brand to give an even shade: One or more coats on old work upto even shade. Quoted rate shall be including at taxes , duties , royalties , lead, lift , trasportation , insurance , GST , cost of sample and laboratory fees etc. Nothing extra shall be paid seperatly. Shade and scheme shall be got approved from Engineer In-charge before taking-up work. Application methodology as specifified by Manufactorer. Approved Makes Nerolac/Dulux/Asian.

Painting with synthetic enamel paint of satin finish approved brand and manufacture to give an even shade : Two or more coats on new work. Quoted rate shall be including at taxes , duties , royalties , lead, lift , trasportation , insurance , GST , etc. Nothing extra shall be paid seperatly. Shade and scheme shall be got approved from Engineer In-charge before taking-up work. Application methodology as specifified by Manufactorer. Approved Makes Nerolac/Dulux/Asian.

Removal and refixing of modular false ceiling of size 595X595 along with grid system and stacking grid and tiles polypacks in suitable boxes at location in IISER PUNE campus as directed by Engineer in charge. Rate shall be inclusive of scaffolding etc. complete . Nothing extra shall be paid separately.

Providing and laying modular false ceiling tile of size 595X595 , quoted rate shall be including removal of existing damaged/bent unservisable tle, disposal to dumping ground within campus.

Repairs to Gypsum/Calcium Silicate Partition/ceiling by providing and fixing 8mm calcium silicate board single/double skin on existing G.I. frame/ceiling including jointing and finishing flush to existing finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer , putty and 2 coat painting suitable for board as per manufacture's specification and direction of engineer in charge all complete. Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process with Compressive Strength 225 kg/sq.cm, Bending Strength 100 kg./ sq.cm . Quoted rate shall be including removing of existing damaged ceiling , making proper supporting arrangement , scaffolding upto 5 meter etc complete. Actual area of board shall be measured for payment.

Providing and fixing wall paneling by 8mm tapered edge calcium silicate board made with calcareous & siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with compressive strength 225 kg/ sq.cm, Bending strength 100 kg/sq.cm over frame work of aluminium /GI/MS etc all complete as per the drawing & directions of engineer-in-charge, the joints of the boards are finished with specially formulated jointing compound and 48 mm wide jointing tape to provide seamless finish.Frame works shall be measured in respective items. Quoted rate shall be including removing of existing damaged ceiling , making proper supporting arrangement , scaffolding upto 5 meter etc complete. Actual area of board shall be measured for payment.

Misc plumbing works associated with closing of existing water points , drain points , closing by using vitrified time cut to appropriate size and shape etc commplete. Minimum 5 water points to be closed , relocated within 3 meter length in 12mm CPVC pipe with 1 valve at each point. Quoted rate shall be including cost of plumbing material , valves , MTA, FTA cost towards chasing in tiles and refixing etc complete. Nothing extra shall be paid seperatly. Each relocated water point shall be measured for payments.

Providing and fixing aluminium work for supports, backing, above ceiling , in partitions with extruded built up standard tubular sections/ appropriate with fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sideswith silicon sealant. Aluminium sections shall be issued departmentelly at stores near dining block.Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly.

Providing and fixing glazing in aluminium Door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge . Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly. (Cost of aluminium snap beading shall be paid in basic item): With glass issued departmentelly at one location in campus , quoted rate shall be including safe lead,lead and installtion of glass of any thickness or size in door and windows.Quoted rates shall be including GST , labour, lead , lift , trasportation etc complete. Nothing extra shall be paid seperatly.

Providing and fixing aluminium composite panel in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3.5mm thick FR grade mineral core sandwiched between wo Aluminium sheets (each 0.25mm thick). The aluminium composite panel sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade using tainless steel screws, nuts, bolts, washers, cleats,weather silicone sealant, backer rods etc.

SEALING OF HOLES BY EXTERIOR GRADE SILICON SEALANT OF DOW CORNING FOR STRUCTURAL GLAZING PURPOSE WITH GOOD ADESION BETWEEN METAL AND FRP/GLASS/ACP. DOW 895 / DOW 995 WITH APPLICATION NOZZLE-GUN PUSH MECHANISUM. BOTTLE OF 300MM

Providing and fixing semi-transpernat glass film of approved make on glass surface as per approved shade and pattern.

Lifting , shifting , unscrewing , removal of granite and complete knockdown of laboratory furniture , removal of under bench cabinates and refixing as per new layout of C frames , granite tops , reagent shelves , under bench cabinates etc complete as per layout by deploying suitable manpower and tools without damaging furniture articles etc complete. Actual plan area of table tops to be dismentelled shall be measured for payments.

Misc plumbing works associated with closing of existing water points , drain points , closing by using vitrified time cut to appropriate size and shape etc commplete. Minimum 5 water points to be closed , relocated within 3 meter length in 12mm CPVC pipe with 1 valve at each point. Quoted rate shall be including cost of plumbing material , valves , MTA, FTA cost towards chasing in tiles and refixing etc complete. Nothing extra shall be paid seperatly. Each relocated water point shall be measured for payments.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. above 35 sq. mm and upto 95 sqmm (clamped with 25x3 mm thick saddle)

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Providing and fixing 12 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

MV Cable Jointing & End Termination : Supplying and making indoor end termination with brass compression gland and aluminum / copper lugs, for following size of PVC insulated and PVC /XLPE sheathed , aluminum / copper conductor cables of 1.1kV grade as required. : Size - 4 C X16 sq.mm Copper ,XLPE Armourd Cable

MV Cable Jointing & End Termination : Supplying and making indoor end termination with brass compression gland and aluminum / copper lugs, for following size of PVC insulated and PVC /XLPE sheathed , aluminum / copper conductor cables of 1.1kV grade as required. : Size - 4 C X 6 sq.mm Copper ,XLPE Armourd Cable

MV Cable Jointing & End Termination : Supplying and making indoor end termination with brass compression gland and aluminum / copper lugs, for following size of PVC insulated and PVC /XLPE sheathed , aluminum / copper conductor cables of 1.1kV grade as required. : Size - 4 C X 25 sq.mm Copper ,XLPE Armourd Cable

MV Cable Jointing & End Termination : Supplying and making indoor end termination with brass compression gland and aluminum / copper lugs, for following size of PVC insulated and PVC /XLPE sheathed , aluminum / copper conductor cables of 1.1kV grade as required. : Size - 1 Core x 70 Sq.mm Copper Flexible FLRS Cables ( Green Outersheath )

MV Cable Jointing & End Termination : Supplying and making indoor end termination with PVC compression gland and aluminum / copper lugs, for following size of PVC insulated and PVC /XLPE sheathed , aluminum / copper conductor cables of 1.1kV grade as required. : Size - 1 Core x 25 Sq.mm Copper Flexible FLRS Cables ( Green Outersheath )

MV Cable Jointing & End Termination : Supplying and making indoor end termination with brass compression gland and aluminum / copper lugs, for following size of PVC insulated and PVC /XLPE sheathed , aluminum / copper conductor cables of 1.1kV grade as required. : Size - 3 1/2 C X 70 sq.mm aluminium ,XLPE Armourd Cable

Supply, loading, transportation unloading at site, storages at site ,shifting from storage place to site, of 1100 Volts grade XPLE insulated over all FRLS outersheathed , Aluminium / copper conductor, un armoured / armoured LT power cables as per IS 7098(Part 1) of following sizes.( Note :- Cable shall be considered flat armoured type for armoured cable ) 1 Core x 25 Sq.mm Copper Flexible FLRS Cables ( Green Outersheath )

Supply, loading, transportation unloading at site, storages at site ,shifting from storage place to site, of 1100 Volts grade XPLE insulated over all FRLS outersheathed , Aluminium / copper conductor, un armoured / armoured LT power cables as per IS 7098(Part 1) of following sizes.( Note :- Cable shall be considered flat armoured type for armoured cable ) 4 C X16 sq.mm Copper ,XLPE Armourd Cable

Supply, loading, transportation unloading at site, storages at site ,shifting from storage place to site, of 1100 Volts grade XPLE insulated over all FRLS outersheathed , Aluminium / copper conductor, un armoured / armoured LT power cables as per IS 7098(Part 1) of following sizes.( Note :- Cable shall be considered flat armoured type for armoured cable ) 4 C X 6 sq.mm Copper ,XLPE Armourd Cable

Supply, loading, transportation unloading at site, storages at site ,shifting from storage place to site, of 1100 Volts grade XPLE insulated over all FRLS outersheathed , Aluminium / copper conductor, un armoured / armoured LT power cables as per IS 7098(Part 1) of following sizes.( Note :- Cable shall be considered flat armoured type for armoured cable ) 4 C X 25 sq.mm Copper ,XLPE Armourd Cable

Supply, loading, transportation unloading at site, storages at site ,shifting from storage place to site, of 1100 Volts grade XPLE insulated over all FRLS outersheathed , Aluminium / copper conductor, un armoured / armoured LT power cables as per IS 7098(Part 1) of following sizes.( Note :- Cable shall be considered flat armoured type for armoured cable ) 3 1/2 C X 70 sq.mm aluminium ,XLPE Armourd Cable

Supplying and fixing 30 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required.

Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32 A 415 V "C" curve TP MCB complete with connections, testing and commissioning etc. as required.

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . Suitable for MCCB 4P incomer (Note : Vertical type MCB where 3 phase outlets are required.) 8 way (4 + 24), Double door

MCCB,MCB&DB'S Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 125 A,36KA,FPMCCB

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 63 A,36KA,FPMCCB

MCCB,MCB&DB'S Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

Supply & installation of surface mounted DLP U- PVC adaptable trunking raceways, fabricated out of U-PVC to Off-White or approved shade as per IS 733 of thickness 2.0 mm for the base and sides with removable covers, complete with necessary bends, suitable sized junction boxes, internal angle, external angle, flat 90 degree angle , end caps and tees etc, Complete. (For every 1mtr distance cable tag has to be provided for each circuit in the raceways - as more that 1C FRLS copper wire is required for 1 Circuit) PVC RACEWAYS ( Along the wall), DLP U- PVC adaptable trunking . Size: 105x 50mm PVC Raceways for Power & Data with above specifications

Supplying and fixing following Modular base & cover plate ( Clip on support for mounting switches etc) on existing DLP U PVC trunking etc. as required. 2/3 module

Supplying and fixing following Modular base & cover plate ( Clip on support for mounting switches etc) on existing DLP U PVC trunking etc. as required. 4 module

Supplying and fixing following Modular base & cover plate ( Clip on support for mounting switches etc) on existing DLP U PVC trunking etc. as required. 6 module

Supply and fixing of seperation partition 85/105 mm in existing DLP U PVC trunking as required.

Supply & fixing following modular switch/ Socket on the exisiting modular plate & switch box including connection but excluding modular plate etc. as required 5/6 amps switch (For Power socket)

Supply & fixing following modular switch/ Socket on the exisiting modular plate & switch box including connection but excluding modular plate etc. as required : 15/16 amp switch (For Power socket)

Supply & fixing following modular switch/ Socket on the exisiting modular plate & switch box including connection but excluding modular plate etc. as required : 3 pin 5/6 amp socket outlet (For Power socket)

Supply & fixing following modular switch/ Socket on the exisiting modular plate & switch box including connection but excluding modular plate etc. as required : 6 pin 15/16 amp socket outlet (For Power socket)

Supply and fixing modular blanking plate on the exisitng modular plate & switch box with matching colour including connection but excluding modular plate etc as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed including medium class PVC conduit as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed exsisting medium class PVC conduit/trunking etc as required. 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed including medium class PVC conduit as required. 4 X 4 sq. mm + 2 X 4 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed exsisting medium class PVC conduit/trunking etc as required. 4 X 4 sq. mm + 2 X 4 sq. mm earth wire

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.. as Group C

Supply Testing commissioning of Recessed Mounted Downlight 15 to 18 W, round shape, aluminium dia case housing, LED, Luminaire with Intelligent Inner Edge Light with Single piece molded Polycarbonate diffuser, Lighting and electrical parameters are inline with round Luminaire. Luminaire should give more volumetric light & higher vertical illumination.Luminaire should be available in different Lumen Packs of 1500 lm with different CCT.. LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=100 lumens/watt, Life of fixture 50000hrs@L70% Lumen maintenance, CCT up to 6500, CRI >80, PF >0.95 and SDCM 4 for good light quality, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.5KV The fixture should comply with the parameters as per IS10322. The LED driver should comply to IEC61000-3-2 ed.3.2, 2009 for Harmonics, IEC61347 -2 -13, 2006 in Conjunction with IEC61347-1 ed.2.0, 2007 for Electrical Safety, IEC62384 ed.1.1, 2011 for performance and IEC61547 ed.2.0, 2009, CISPR-15 for EMI. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters Make Philips / Wipro / Syska

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable

Supply and making end termination for UTP 4 pair CAT 6 LAN cable with required IO modules which is suitable for modular type base , cover plates and accessories ( At field side ) as required.

Supply and making end termination for UTP 4 pair CAT 6 LAN cable with required IO modules which is suitable for modular type base , cover plates and accessories ( At rack side ) as required.

Supply & installation of 24 port Jack fully loaded Patch Panel, make D link with required accessories as complete.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 32 mm

EARTHING SYSTEM : Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

MCCB,MCB&DB'S Supplying and fixing 63 A rating, 240/415 V, 10 kA, "C"curve, miniature circuit breaker suitable for inductive load of four pole poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Cutout in existing panel with 10 sqmm copper flex cable = 10 meter and required termination is in scope of agency.

Supply Installation testing and commissioning of ductable Air conditioning unit of capacity 8.5 TR with a minimum airflow of 3400 CFM. The unit should be complete with indoor and outdoor units. outdoor unit mounted with suitable metal stand with R410 or equivalent green refrigerant gas only. The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately. The outdoor unit consists of condensing unit, microprocessor control panel, scroll compressor, condensing fan, liquid reciever & Etc.And theindoor unit consists of blower fan, evaporator coil and a controller connected with corded remote controller for controlling the temperature. The rate shall be inclusive of cost of all the materials, labour for installation, import duty/excise,all taxes & levies, octroi etc. and nothing extra shall be payable. (Make : Toshiba / Carrier/ Mitsubishi / Daikin)

Refrigerant Piping Hot gas line - hard pipe with 13 mm thick insulation Supply, installation, testing and commissioning of refrigerant Suction & liquid piping using eddy current free Copper pipes and fittings like elbows, couplers, tee joints, brass fittings, "U" loops, expansion loops etc. Supports consisting of GI box / "C" sections & female anchor fasteners with full threaded GI rods, insulation of pipes using 13 mm thick elastomeric closed cell Nitrile Rubber insulation material having class "O" for fire properties, structural clamps with hard PVC pipe sleeves under the clamps to protect insulation at supports, tagging to enable tracing connectivity to respective units as per shop drawings to be generated by contractor and approved by consultant. Submission of test reports in approved format forms a part of this item scope. Making up of any leakages occuring during testing / commissioning / first calender year from handing over, including supply, labour, consumables, refrigerant, top up, oil top up and incidental expenses also forms a part of the scope covered under this item.

Refrigerant Piping Liquid line - hard pipe with 13 mm thick insulation Supply, installation, testing and commissioning of refrigerant Suction & liquid piping using eddy current free Copper pipes and fittings like elbows, couplers, tee joints, brass fittings, "U" loops, expansion loops etc. Supports consisting of GI box / "C" sections & female anchor fasteners with full threaded GI rods, insulation of pipes using 13 mm thick elastomeric closed cell Nitrile Rubber insulation material having class "O" for fire properties, structural clamps with hard PVC pipe sleeves under the clamps to protect insulation at supports, tagging to enable tracing connectivity to respective units as per shop drawings to be generated by contractor and approved by consultant. Submission of test reports in approved format forms a part of this item scope. Making up of any leakages occuring during testing / commissioning / first calender year from handing over, including supply, labour, consumables, refrigerant, top up, oil top up and incidental expenses also forms a part of the scope covered under this item.

SHEET METAL WORKS :- 0-750 -------0.63 MM (24G) with flanges Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.

Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.

Duct thermal insulation :- 19 mm thick Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.

Supplying, installing & testing of 9 mm thick acoustic lining Class '1' open cell nitrile rubber within supply and return air ducts as per the specifications. All ducts shown cross hatched on the approved shop drawings shall be provided with acoustic lining of open cell nitrile rubber insulation with density 140-180 Kg/ cum as per technical specifications with all the necessary mounting accessories as required for complete installation. The thermal conductivity of insulation shall not be more than 0.045 W/m°k @ 0°C mean temperature. THe material shall have anti microbial property

UPVC drain pipes:- 25 mm dia. Supply, Installing, testing and commissioning of UPVC pipe for condensate complete with 6mm thick nitrile rubber insulation drain for AHUs/ FCU, cut to required length with necessary, clamps, supports, hangers, fittings such as bends, tees, reducers etc to nearest drain point complete as per technical specifications with all the necessary mounting accessories as required for complete installation.

3C x 4 Sq.mm. ( XLPE Copper Armoured Cables ) Supply, laying and commissioning of following size 1.1KVgrade XLPE PVC insulated armoured copper conductor cable, on cable tray with all installation materials including necessary double compression glands and terminations.

2.0 Tr Dx hiwall units Supply of 2.0 TR Hiwall type with inverter compressor with min 4 star rating of any green gas air condition Unit comprising of Air filter, Two/Three level fan Speed motor, DX - cooling coil, Drain pan, Washable Grill, Auto - swing Louvers,and outdoor stand.The outdor unit should be mounted on the suitable stand. The machine cost should include cost for cordless remote for controlling the temperature and ON/OFF siwtch and panel.The quoted rates shall be inclusive of all taxes and levis, duties, lead, lift,transpotation, placing, scaffolding, core cutting of required diameter in walls, finishing and minor civil works and nothing shall be paid separately.(Make : Toshiba /Mistubishi / Daikin).

Installation testing and commissioning charges of 2.0 tr dx type hiwall units.

Supplying & fixing of copper refrigerant piping for 2 tr split hiwall air condition units with minimum 9 mm insulation complete from indoor unit to outdoor unit with supports Etc.

Supply and installation of M.S. stand for outdoor units

Supplying and laying of 6 x 1.5 sq mm PVC insulated copper conductor flexible cable.

Supplying & fixing 25/32 mm size PVC drainage pipe with insulation i/c cutting the wall, finishing etc. as reqd.

Supply and installation of spot extractor (Elephant Trunk) of 75 mm diameter pipe

PP-FRP DUCTING & ACCESSORIES : - Ducting upto 500mm Dia - wall thickness shall be 3 mm PP and 3 mm FRP. Supply and installation of PP-FRP ducting with glass lined (GL) finish, FRP lining shall be of fire resistant Bisphenol resin. Duct pricing is inclusive of all necessary flanges, bends, entry branches, tapers, inspection door, gaskets for flanges, bolt & nuts, washers, support angle, hanger threaded rods with anchor bolts for fixing. Rate is inclusive of enamel painting for exposed surfaces. Mode of measurement shall be in sqm, measured as circumference x running length, extra will not be paid for accessories such as flanges, bends, elbows, Y piece, branch off, reducers, tapers, entry doors, inspection doors, gaskets etc.

Supply, installation, testing , commissioning of Gas Distribution System for Laboratory Gases in SS 304 seamless tube. All Joints shall be compression fittted ferrule type fittings of approved makes. System shall be tested and handed over at 10 bar pressure test till Manfold. All components up to manifold system of Gas Bank System shall be tested at minimum 150 bar and Leak free , full functional GDS system shall be handed over to IISER PUNE . Quoted rate shall be including all necessary fittings, tools , tackles , bending tool , welding machine , GST , lead , lift etc and all necessary equipment’s required at site. Agency shall submit PN & ID and obtain approval of Engineer In-Charge before taking-up GDS works. Wall marking shall be done showing GDS route actal at site and approval on profile making shall be obtained before fixing of tubes. System shall be guaranteed for 1 year for leakage and fittings , comprehensive guarantee of complete system shall be submitted on Rupees Five hundred bond paper with free replacement of defective components to IISER PUNE. Actual components listed below installed at site shall be measured for payments. Nothing extra shall be paid seperatly.LABORATORY GAS DISTRIBUTION SYSTEMManifold Block with mounting bracket : Fabricated Type for SS 304 1/4" System for single cylinder

Manifold Block with mounting bracket : Fabricated Type for SS 304 1/4" System for single cylinder

1/4 " cylinder Isolation Valve

Cylinder mounted Two Stage Regulator (Inlet pressure 250 bar and outlet pressure 0 to 16 bar)

1/4 " OD Flexible Hose with bullnose connector & safety wire rope (1 meter long)

Cylinder bracket with Chain

Ball valve 1/4" OD

Check valve 1/4 " NPTF x 1/4" NPTM

Supply and installation of flash back arrester for Oxygen gas.

Supply and installation of flash back arrester connectors for Oxygen gas.

Supply and installation of SS 304 , Seamless Tube 1/4" OD

Purification panel for the gases with moisture trap & oxygen trap with pressure regulator, toggle valve inlet & outlet connection of size 1/4".OD

Union 1/4" diameter

PP clamp set 1/4" OD

Alluminium profile

Please Note that quoted rates are inclusive of all taxex,levies,duties,labour,transportaion etc. nothing extra shall be paid separtely.