Renovation of Conference Room No. 508 and 114 for National Human Rights Commission NHRC, Manav Adhikar Bhawan, GPO Complex, New Delhi

ABSTRACT OF COST

Name of Work : Renovation work comprising of civil work, Electrical work, low voltage

Sub Head No. work Description Total

1 Amount for renovation of conference room 6,189,685.12

(114) at National Human right commission

2 Amount for renovation of conference room 13,027,315.08

(508) at National Human right commission

Total Cost 19,217,000.00

Digitally signed by AMIT

GERNAL ABSTRACT OF COST

Name of Work : ESTIMATE FOR RENOVATION OF CONFERENCE ROOM (114) AT NATIONAL HUMAN RIGHTS COMMISSION

Sub Head No. Description DSR NDSR/MR Total

CHAPTER-1 CIVIL CONSTRUCTION

SH.1 Carriage Of Materials 7,017.00 0.00 7,017.00

Total Cost of Civil, Electrical, HVAC Works 892,188.00 589,348.30 1,481,536.30

SH.8 Total Cost of AV Work 0.00 4,708,148.82 4,708,148.82

Total Cost A 6,189,685.12

Digitally signed by AMIT

ABSTRACT OF COST

Name of Work : ESTIMATE FOR RENOVATION OF CONFERENCE ROOM (114) AT NATIONAL HUMAN RIGHTS COMMISSION

I.NO DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT CODE

SH CARRIAGE OF MATERIALS 1.00

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste

material by mechanical transport including loading, transporting, unloading to approved

municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of

Engineer-in-charge.

Note - item to be applicable in urban areas having directions for restricted hours for

movement/ plying of load carrying motor vehicle of 3.5 cum or more.

Total Carried Over to Abstract for Sub Head: 1.00 Carriage Of Materials : ₹ 7,017.00 ₹ 0.00

SH WOOD AND P.V.C. WORK 2.00

Poviding and fixing partition upto ceiling height consisting of G.I. frame and required

board, including providing and fixing of frame work made of special section power

pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive),

consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and

0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with

MR dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal

screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other

flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel

and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts,

including fixing of studs along both ends of partition fixed flush to wall with suitable anchor

fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre,

and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs,

floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to

be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing

channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided AOR -1

at the horizontal joints of two boards, fixed to the studs using metal to metal flat head sqm 100.00 ₹ 1,465.15 ₹ 146,515.00 Based on

screws, including jointing and finishing to a flush finish with recommended jointing 9.105.2

compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher

and two coats of primer suitable for board as per manufacture's specification and

direction of engineer in charge all complete.

SH ROOFING WORKS 4.00

PLAIN GYPSUM BOARD CEILING

Digitally signed by AMIT

Providing and fixing false ceiling at all height including providing and fixing of frame work

made of special sections, power pressed from M.S. sheets and galvanized with zinc

coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats

of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to

centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with

6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of

required length with nuts & bolts of required size and other end of angle hanger fixed with

intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to

centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in

a direction perpendicular to G.I. intermediate channel with connecting clips made out of

2.64 mm dia x 230 mm long G.I. wire at every junction,

including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and

30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at

450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the help of dry wall screws of

size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered

and square edges of the board with recommended jointing compound , jointing tapes ,

finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint

and two coats of primer suitable for board, all as per manufacturer's specification and also

including the cost of making openings for light fittings, grills, diffusers, cutouts made with

frame of perimeter channels suitably fixed, all complete as per drawings, specification

and direction of the Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011

(Board with BIS certification marks)

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of

approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of

99%, Light Reflectance ? 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire

Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-

Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120

4.2 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm 26.27

of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm

to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel

item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm

diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of

size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’.

Digitally signed by AMIT

The system should rest on periphery walls /partitions with the help of GI perimeter wall

angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with

help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The

exposed bottom portion of all T-sections used in false ceiling support system shall be pre-

painted with polyester baked paint, for all heights. The work shall be carried out as per

specifications, drawings and as per directions of the engineer-in-charge.

A With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7) sqm 22.00 ₹ 2,362.10 ₹ 51,966.00 26.27.2

Total Carried Over to Abstract for Sub Head: 4.00 Roofing Works : ₹ 90,928.00 ₹ 0.00

SH FINISHING 5.00

INTERIOR FINISHING

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to

prepare the surface even and smooth complete.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as

per manufacturers specifications :

Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of

Special primer applied @ 0.75 ltr /10 sqm

LIGHTWEIGHT GYPSUM PLASTER

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum

lightweight plaster having additives and light weight aggregates as vermiculite/ perlite

5.3 respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven sqm 10.00 ₹ 363.45 ₹ 3,635.00 13.78

background such as bare brick/ block/ RCC work on walls & ceiling at all floors and

locations, finished in smooth line and level etc. complete.

MELAMINE CLEAR POLISH

Polishing in high gloss/matt finish melamine clear polish on wood work in required

color/wooden shade texture with following process in the sequence as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand

paper of 160/180 nos.

2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st

coat and 2nd coat is allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample

water to remove excess sealer layer and make the surface further smooth after this wet

rubbing, then surface is applied with special grade melamine fillers to fill all the small and

big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light

wet rubbing is done this surface is further allowed to dry for 12 hrs.

Digitally signed by AMIT

4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear

polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs

then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12

hrs. The final melamine polish is applied with compressor pressure spray gun using

melamine clear polish and melamine thinner mixed in required proportion complete as

per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of

5.6 6 MM THICK LACQURED FACING

Providing & fixing 6 mm thick annealed SCG Planilaque Evolution (premium GRIHA rated

lacquered glass i.e. textured from saint gobin) with flat polished edge fixed to 5.5 mm thick

. plain MDF board backing with neutral silicone and/or double-sided adhesive pads etc.

,including polishing/MTG all complete as per the drawing & directions of engineer-in-

5.7 BLACKOUT ROLLER BLINDS

Supplying and fixing of Blackout blinds to the following specs.

Black-out material fibre-glass coated fabric, 12 mils thick, 62 threads per sq in., 0.750 lbs per

sq in. (441g per sq mt.)

Operation: - Manual. Offset side-mounted metal chain operated

Mounting: Closure Box in metal

Shade Orientation: Regular roll, shade cloth falls at window side of roller

Configuration: Single band

The Fabric to be as per approved sample (Fabric should be Fire Retardent Certified).

Cellular Semi Opaque 100% Polyester Hardware SpecificationHeadRail: Head rail is 17 mm

high and 47 mm wide, Thickness 1.00 mm. It is made up of powder coated high strength

aluminum alloy covered by two end caps made up of PVC.Drum & Cradle: They are

molded ABS components with high strength metalic drum which are meant for controlling

the lifting cord.Bottom Rail: This is Aluminum Extruded Rail Made up of High Strength

Aluminum alloy, Which is powder coated in white.Installation Bracket: It is made up of mild

steel with zinc plate.Bottom Rail End Cap: It made up of high strength ABS.White Cord: It is

made of Nylon braided non stretchable thread of 1.2 mm thickness.PVC Slip : It is made up

of high strength PVC of width 25 mm.Fabric: 100% spun bonded non-woven polyester

translucent fabric Pleat dimension 3⁄4” hexagonal cell with a distinct air pockets Sanitized,

Weight : 145 + 5% GSM, Thickness : 0.14 -0.17, colour fastness of light – 4-5 Grade ( DIN EN

Supplying and fixing of Room Signages in imp.aluminum profile with 3 mm acrylic

5.8 Gents/Ladies pictograph printed on canvas (Room Names/Exit Signage) - Include braile Nos 3.00 ₹ 816.00 ₹ 2,448.00 MR-22

letterings Size is 6"x10".

5.9 Refurbishment of existing Table at Conference RooM, Windows, Doors etc. LS 1.00 ₹ 150,000.00 ₹ 150,000.00

Digitally signed by AMIT

Total Carried Over to Abstract for Sub Head: .00 Interior Finishing : ₹ 50,897.00 ₹ 294,992.00

Digitally signed by AMIT

NHRC :- HVAC WORK

I.NO DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT CODE

SH OUTDOOR UNIT 1.00

Supply Installation, Testing & Commissioning of modular type Variable

Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units

suitable for cooling and heating, having all hermetically sealed

inverter type Scroll Compressor(s), minimum two compressors for above

14 HP modules, microprocessor based Controller, top discharge type

condensing unit(s), with R 410 A Refrigerant, vibration isolators, with

suitable foundation etc. complete as required. The unit shall deliver the

rated capacity at AHRI Conditions and work even at 50°C ambient Per HP 10 ₹ 16,415 ₹ 164,150 1

temperature without tripping. The unit shall be suitable to work on 400V

+/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first

charge of the refrigerant and ready for use as required. The COP at

AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .

Total Carried Over to Abstract for Sub Head: 1.00 Outdoor Unit :

SH INDOOR UNIT-CASSETTE TYPE 2.00

Supply, installation, testing and commissioning of following

minimum capacity 4-way flow VRV/VRF Cassette Type Indoor

ceiling mounted unit equipped with synthetic washable media

pre-filter, fan section with low noise fan/dynamically balanced

blower, multispeed motor, coil section with DX Copper coil,

electronic expansion valve, outer cabinet, drain pump, grill,

necessary supports, vibration isolation, cord less remote control

etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC 2

supply, complete, as required. The unit shall have automatic

force shut down provision in case of fire on receiving signal from

BMS System. The cooling capacity of indoor unit will be at air

inlet conditions of 27 Degree C DB and 19 Degree C WB

2.3 1.6 TR capacity Cassette Unit Each 0 ₹ 30,204 ₹ - 2.4

2.4 2.4 TR capacity Cassette Unit Each 2 ₹ 31,453 ₹ 62,906 2.6

Total Carried Over to Abstract for Sub Head: 2.00 Indoor Unit-

Cassette Type :

SH Fresh Air Unit with inline fans 3.00

Supplying, Installing, Testing and Commissioning of Inline fans

complete with motor, supporting frame, gravity louvres, ducting,

Flexible duct, diffusers etc. as per drawings and specifications.

SH COPEER REFRIGERANT PIPING 4.00

Supply, Installation, testing and commissioning including

vaccumiazation and Nitrogen testing of following nominal sizes

of soft/hard drawn copper refrigerant piping for VRV/VRF system,

complete with fittings, with suitable adjustable ring type hanger

supports, jointing/brazing including accessories, insulated with

Class-O tubular insulation/with Class-O closed cell elastometric

nitrile rubber tubular sleeves sections of specified thickness as

given below for Suction and Liquid lines, all accessories as per

4.1 specifications etc. as required :

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

4.1.1 mm thick insulation

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

4.1.2 mm thick insulation

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with

4.1.3 19 mm thick insulation

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with

4.1.4 19 mm thick insulation

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with

4.1.5 19 mm thick insulation

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with

4.1.6 19 mm thick insulation

25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with

4.1.7 19 mm thick insulation

Total Carried Over to Abstract for Sub Head: 4.00 Copeer

Refrigerant Piping :

SH Drain Piping 5.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, having thermal stability for hot & cold water supply,

including all CPVC plain & brass threaded fittings, including

fixing the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent cement

and testing of joints complete as per direction of Engineer in

5.1 Charge. Digitally signed by AMIT

I.NO DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT CODE

5.1.125 mm nominal dia Pipes RM 50 ₹ 150 ₹ 7,500 MR-2

6.1.2 19mm insulation RM 40 ₹ 120 ₹ 4,800 MR-3

Total Carried Over to Abstract for Sub Head: 5.00 Drain Piping : ₹ 0.00 ₹ 18,600.00

Digitally signed by AMIT

(C1: Internal Electrical Installation)

Description Rate Unit Amount Remarks

1) Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable in

surface / recessed steel conduit, with modular switch, modular plate,

suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable etc. complete as required.

2) Wiring for group controlled (looped) light point/fan point/exhaust fan

point/ call bell point (without independent switch etc.) with 1.5 sq. mm

FRLS PVC insulated copper conductor single core cable in surface/

recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS

PVC insulated copper conductor single core cable etc. complete as

3) Supplying and fixing suitable size GI box with modular plate and cover in 15 ₹ 477.00 Each ₹ 7,155.00 DSR 1.31

front on surface or in recess, including providing and fixing 3 pin 5/6 A

modular socket outlet and 5/6 A modular switch, connections etc.

complete as required.

4) Supplying and fixing suitable size GI box with modular plate and cover in 12 ₹ 586.00 Each ₹ 7,032.00 DSR 1.32

front on surface or in recess, including providing and fixing 6 pin 5/6 &

15/16 A modular socket outlet and 15/16 A modular switch, connections

etc. complete as required.

5) Wiring for circuit/ submain wiring & DB controlled Light Point along with

earth wire with the following sizes of FRLS PVC insulated copper

conductor, single core cable in surface/ recessed steel conduit complete

a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 250 ₹ 327.00 Metre ₹ 81,750.00 DSR 1.7.1

6 Supplying and fixing of following sizes of steel conduit along with

accessories in surface/recess including painting in case of surface

conduit, or cutting the wall and making good the same in case of

recessed conduit complete as required.

7) Supplying and drawing following sizes of FRLS PVC insulated opper

conductor, single core cable in the existing surface/ recessed steel/ PVC

conduit complete as required. (For UPS Power Workstation)

8) Supplying and fixing following modular switch/ socket on the existing

modular plate & switch box including connections but excluding modular 1.24

plate etc. as required.

3 pin 5/6 amp socket outlet 6 122.00 Each ₹ 732.00 1.24.4

6 pin 15/16 amp socket outlet 5 197.00 Each ₹ 985.00 1.24.5

9.0) Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in

the existing MCB DB complete with connections, testing and

commissioning etc. as required.

10) Supplying and fixing following way, vertical type three pole and neutral,

sheet steel, MCB distribution board, 415 volts, on surface/ recess,

complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, 2.5

interconnections, powder painted including earthing etc. as required.

(But without MCB/RCCB/Isolator)

Digitally signed by AMIT

11) Supplying and fixing following rating, double pole, (single phase and

neutral), 240 volts, residual current circuit breaker (RCCB), having a

sensitivity current upto 300 milliamperes in the existing MCB DB 2.14

complete with connections, testing and commissioning etc. as required.

12) Wiring for circuit/ submain wiring alongwith earth wire with the following

sizes of FR PVC insulated copper conductor, single core cable in 1.14

surface/ recessed steel conduit as required

2 X 4 sq. mm + 1 X 4 sq. mm earth wire 50 334.00 Metre ₹ 16,700.00 1.14.3

2 X 6 sq. mm + 1 X 6 sq. mm earth wire 439.00 1.14.4

4 X 10 sq. mm + 2 X 6 sq. mm earth wire 0 1005.00 Metre ₹ 0.00 1.14.10

13) Supplying and fixing of following sizes of steel conduit along with

accessories in surface/recess including painting in case of surface

conduit, or cutting the wall and making good the same in case of

recessed conduit as required.

SH-VI LIGHTING FIXTURES & OCCUPANCY SENSOR

14) Supply, installation, testing and commissioning of the following fixtures

with all accessories including drivers, LED Lamps complete etc. as

required. Including Dimmable ballasts (DALI)

a. LED indoor surface downlighter having pressure die-cast Al housing 10 ₹ 1,889.03 Each ₹ 18,890.30 MR-20

with diffused optics. The luminaire should have CRI > 80 and CCT of

4000K. The luminaire shall be compliant with IP20, IK02

classification.The fixture should have a minimum system efficacy of 110

lumen/Watt and a minimum system lumen output of 1200 lumens and

maximum system wattage of 11 Watts.. The electronic driver used shall

have a power factor >0.95 , THD <10%.The Luminaire shall be with

LM79 and LM 80 certifications given by NABL/UL accredited lab, Fixture

and Driver to have separate BIS approval.Including Dimmable ballasts

c. Recessed mounted 2X2 LED panel ,made of CRCA housing with high 10 ₹ 7,293.00 Each ₹ 72,930.00 MR-21

efficiency PS Diffuser. LED Used shall be SMD type and fixture should

have minimum efficacy at System level >=120 lumens/watt with

Minimum system Lumens 3000 & Max System wattage of 25W, CCT of

4000K (SDCM<=5), CRI Ra >=80, THD<10%, PF >0.95, an operating

Voltage Range of 140 - 270 VAC.Minimum Internal Surge Protection

4.0KV & IP20/IK02 protection,The Luminaire shall be with LM79 and LM

80 certifications given by NABL/UL accredited lab, Fixture and Driver to

have separate BIS approval.Including Dimmable ballasts (DALI)

i. 600mm dia Pendent Mounted Ring LED. Fixture to be made of extrusion 4 ₹ 30,984.00 Each ₹ 123,936.00 MR-22

Aluminum housing in black finish RAL9005 with high efficiency

polycarbonate/PS diffuser. LED Used shall be SMD type with Minimum

system Lumens 3000 @30W & efficacy 100lm/W,Life of fixture : 50000

burning Hrs. @ L70B50 Lumen maintenance, CCT of 4000K/6500K

(SDCM<=5), CRI Ra >=80, PF >0.95, operating Voltage Range of 140-

270 V AC. Minimum Internal Surge Protection 4.0KV. Manufacturer shall

have inhouse lab approved by NABL or ministry of science of govt of

India. LM 79 and LM80 reports need to be submitted from a NABL/UL

accredited lab to verify above parameters. Both the fixture and Driver

should have separate BIS approval. Fixture dimensions are Ø 600 X

W100mm X H 60 mm. Make Havells Model Torus

15) Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along 45 ₹ 53.00 Metre ₹ 2,385.00 DSR 17.5.4

with all ancillaries and accessories like coupler etc. as required.

16) Supply of the following LED light fixtures with all accessories, such as,

Dimmable ballasts (DALI), complete.

OCCUPANCY SENSOR

Digitally signed by AMIT

1) Supplying,installation,testing and commissioning of Passive Infrared 2 ₹ 4,602.00 Each ₹ 9,204.00 DSR 15.1

(PIR) technology based occupancy sensor having high prefoMetreance,

non regulating programmable type, suitable for connected load upto

10Amp , for mounting height up to 2.8 mtr and for 5 m diameter

coverage area along with necessary fixing arrangements i/c

programming at site etc. complete as required

2) Supplying,installation,testing and commissioning of Passive 2 ₹ 9,171.00 Each ₹ 18,342.00 DSR 15.2

Infrared(PIR) technology based occupancy sensor with day light

dimming(lighting level shall be regulated as per availability of natural day

light in an area along with occupancy detection.) having high

prefoMetreance, regulating programmable type, suitable for connected

load upto 10Amp, for mounting height up to 2.8 mtr and for 5 m diameter

coverage area along with necessary fixing arrangements i/c

programming at site etc. complete as required.

SH-VII LIGHTNING PROTECTION.

Total of C1: Rs. ₹ 553,440.30

Digitally signed by AMIT

S.No. Item Specifications Unit Qty Price Amount

Supply, Installation, testing and commissioning of 98"

smart 4K LED Display,Audio Built in Speaker(10W +

10W),HDMI 2.0 X 2, USB 2.0 x 1 , Audio Input X 1,

OUTPUT Type Stereo Mini Jack, HDMI X 1, Duty Cycle 24

1 98" Screen x 7, Speacial features, File support Direct vieweing of PPT, Nos 1 ₹ 1,250,000.00 ₹ 1,250,000.00

Word ,PDF, Images and video from pen drive, EXTERNAL

CONTROL RS232C(in) thru stereo jack, RJ45, Brightness

TYP300, Accessories=wall stand/ Table stand, Remote and

standard cables

Supply, Installation, testing and commissioning of Ceiling

Microphone tile with 15 or more no. of built-in

microphone, coverage area : 39sq mtr or more, should be

Powered over Ethernet, Should have Dante and control

over single CATx cable (qty of microphone will vary as per

2 the mentioned coverage area and built in micorphone), Nos 2 ₹ 418,900.00 ₹ 837,800.00

should come with lighting indicator, It should work on

open control protocol software and compitable to

monitor with a single sofware for all the microphone in

the campus etc complete required as per

the specifications.

Suppy Installation Testing and Commissioning of digital

signal processor with minimum 14no. Or more Mic / line

input with phantom power and AEC and 8 or more line

level output, 1no. Or more GPIO at least 2 channel of USB

input and output for software Video Conferencing, should

Digital Signal have 64x64 channel of digital dante input output, Should

Processor have sampline rate of 48kHz or better, Should be

expandable for port expansion, should support Control

with App via iOS and Android devices, or any third-party

control system, Shall have Built-in filters, feedback

suppression, AGC etc complete as required as per

Supply, Installation, testing and commissioning of Quad

channel energy star rated digital power amplifier,Quad

channel 4 Ohm or 8 ohm energy-efficient amplifier - 4 x

30W or more 70/100V Technology : Class-D,Input linking

4 Amplifier through miniature switches, Switching mode power Nos 1 ₹ 176,832.44 ₹ 176,832.44

supply, Protection : DC Short circuit & Over heating &

Over load & Signal limiting, Frequency Response 120 Hz -

20 kHz or better, Silent passive cooling etc complete

required as per specifications.

Supply, Installation, testing and commissioning of 6.5"

two-way coaxial thin edge ceiling loudspeaker, 100V

transformer power taps : 24,12,6, watts, Conical

5 Speaker dispersion : 145° or more, impedance : 8, low impedance Nos 6 ₹ 13,557.02 ₹ 81,342.12

RMS continous power : 30watts, frequency range : 50 Hz -

20 kHz or better, frequency response : 60Hz - 20KHz or

better etc complete required as per specifications.

Supply Installation Testing and Commissioning of surface-

mount USB-to-Dante endpoint, two-way volume and

mute sync for Microsoft Teams,compliant with CE and

FCC, device shouold have Power-over-Ethernet (PoE) to

IEEE 802.3af Class 0 standard and support Dante

USB to Dante networking using standard CatX cable, device should

converter support the Speakerphone profile with and without echo

cancellation, enable two-way volume and mute

syncronization with both PC and Mac platforms, Dante

with AES67 compliance,Sampling Rate(s) 48 kHz,should be

from same OEM as DSP etc complete required as per

specifications.

Touch Panel Suppy Installation Testing and Commissioning of control

control system with touch panel/Ipad

Digitally signed by AMIT

Supply, Installation, testing and commissioning of Four

HDMI inputs matrixed to Four HDMI outputs with HDMI

4*4 HDMI 2.0a specification and 18Gbps (600MHz) 4K UHD support,

switcher HD resolutions up to 3840×2160@60Hz (4:4:4, 8-bit) &

4096×2160@60Hz (4:4:4, 8-bit), 16-bit Deep Color up to

Supply, Installation, testing and commissioning of HDMI

RX extender with complies with the advanced HDCP 2.2

and HDMI 2.0 standards, uncompressed HD audio and

video as well as control via a single run of Cat.5e/6/7

cable over distances of up to 70 meters and upto 40mat

4K, HDBaseT feature support: HD Video and Audio, and

Control (IR/RS-232 pass-through) and CEC bypass,

Supports pass-through of many audio formats including

LPCM (up to 8 channels), Bitstream and HD Bitstream

Supply, Installation, testing and commissioning of HDMI

TX extender complies with the advanced HDCP 2.2 and

HDMI 2.0 standards, uncompressed HD audio and video

as well as control via a single run of Cat.5e/6/7 cable over

distances of up to 70 meters and upto 40mat 4K,

10 Transmitter HDBaseT feature support: HD Video and Audio, and Nos 3 ₹ 29,500.00 ₹ 88,500.00

Control (IR/RS-232 pass-through) and CEC bypass,

Supports pass-through of many audio formats including

LPCM (up to 8 channels), Bitstream and HD Bitstream

Supply Installation Testing and Commissioning of HDMI

Audio Extractor should extract up to 2 channels of LPCM

audio or 5.1 channels of Bitstream audio from an HDMI

source, allowing the user to convert high quality HDMI

audio into more convenient analog (LPCM 2.0 sources

only) or optical signals for use with powered speakers or

non-HDMI AV receivers. Both the input and output HDMI

ports should support 4K UHD resolutions up to 4K@60Hz

(4:4:4, 8-bit) and should capable of providing high quality

HDMI audio and video performance. The unit should supports

Deembedder passthrough of HD and standard Bitstream formats as well

as LPCM 7.1 with audio sampling rates up to 192kHz. Built-

in EDID management support allows the user select from

multiple EDIDs and, with the use of optional PC software,

to upload, download, or edit EDID files etc and complete

Supply of Recording, Streaming & Webcasting Hardware

simultaneously, Built-in HDMI, 3G-SDI, IP & USB 3.0 Video

Inputs with 1x Line In and 1x XLR Input, 2x HDMI Outputs,

Can record upto any two inputs simultaneously in a single

frame and as well as individual sources simultaneously.

Live Streaming Should have minimum 1TB inbuilt storage and can be

/ Recording connected to local NAS storage. The system should be

able to support minimum 3 unicast streams.The recorded

files should have the option of time and date stamp. OEM

should be CE, FCC & RoHS Certified

wireless Supply, Installation, testing and commissioning of wireless

presentation presentation device

Network Supply, Installation, testing and commissioning of 16 port

Supply, Installation, testing and commissioning of Cable

cubby (1 HDMI, 1LAN,1 Charging socket)

16 Network Rack 24U AV equipment rack Nos 1 ₹ 14,750.00 ₹ 14,750.00

17 Cables Cables & connectors Lot 1 ₹ 100,000.00 ₹ 100,000.00

Total Cost of AV Work 1 ₹ 4,708,148.82

Note: We have considered existing VC installed at 508 for room no. 114.

Digitally signed by AMIT

GERNAL ABSTRACT OF COST

Name of Work : ESTIMATE FOR RENOVATION OF CONFERENCE ROOM (508) AT NATIONAL HUMAN RIGHTS COMMISSION

Sub Head No. Description DSR NDSR/MR Total

SH.1 Carriage Of Materials 7,017.00 0.00 7,017.00

SH.3 Cladding Work 8,995.00 0.00 8,995.00

SH.5 Flooring Works 366,424.00 0.00 366,424.00

SH.10 Dismantling And Demolishing 20,000.00 0.00 20,000.00

SH.11 Sanitary Installations 3,303.00 9,048.65 12,351.65

SH.13 Water Proofing 3,616.00 0.00 3,616.00

Total Cost of Civil, Electrical, Furniture and HVAC Works 2,805,995.30

Total Cost A 13,027,315.08

Digitally signed by AMIT

ABSTRACT OF COST

Name of Work : ESTIMATE FOR RENOVATION OF CONFERENCE ROOM (508) AT NATIONAL HUMAN RIGHTS COMMISSION

I.NO DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT CODE

SH CARRIAGE OF MATERIALS 1.00

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste

material by mechanical transport including loading, transporting, unloading to

approved municipal dumping ground for lead upto 10 km for all lifts, complete as per

directions of Engineer-in-charge.

Note - item to be applicable in urban areas having directions for restricted hours for

movement/ plying of load carrying motor vehicle of 3.5 cum or more.

Total Carried Over to Abstract for Sub Head: 1.00 Carriage Of Materials : ₹ 7,017.00 ₹ 0.00

SH MASONRY WORK 2.00

AUTOCLAVED AERATED CEMENT BLOCKS-AAC

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick

AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4

(1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6

mm dia M.S. bars at every third course of masonry work.

Total Carried Over to Abstract for Sub Head: 2.00 Masonry Work : ₹ 18,671.00 ₹ 0.00

SH CLADDING WORK 3.00

Providing and fixing 12 mm thick gang saw cut, mirror polished, premoulded and

prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and

similar locations of required size, approved shade, colour and texture laid over 18 mm

thick thick BWP ply board, joints treated with white cement, mixed with matching

pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges

to give high gloss finish etc. complete at all levels.

A Granite stone slab colour black, Cherry/Ruby red 8.2.2

Extra for providing opening of required size & shape for wash basin/ kitchen sink in

kitchen platform, vanity counter and similar location in marble/ Granite/ stone work,

including necessary holes for pillar taps etc. including moulding, rubbing and polishing of

cut edges etc. complete.

Total Carried Over to Abstract for Sub Head: 3.00 Cladding Work : ₹ 8,995.00 ₹ 0.00

SH WOOD AND P.V.C. WORK 4.00

Digitally signed by AMIT

Poviding and fixing partition upto ceiling height consisting of G.I. frame and required

board, including providing and fixing of frame work made of special section power

pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive),

consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and

0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre

with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or

metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm

and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and

ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts

and nuts, including fixing of studs along both ends of partition fixed flush to wall with

suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to

and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs,

floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to

be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing

channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be AOR -1

provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat sqm 26.40 ₹ 1,465.15 ₹ 38,680.00 Based on

head screws, including jointing and finishing to a flush finish with recommended jointing 9.105.2

compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint

finisher and two coats of primer suitable for board as per manufacture's specification

and direction of engineer in charge all complete.

COMMERCIAL PLY PLAIN LINING

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a

coat of approved primer on one face, and fixed on wooden /steel frame work,

complete as per direction of Engineer-incharge (Frame work shall be paid for

A 12 mm thick commercial ply conforming to IS : 1328 BWR type sqm 17.30 ₹ 1,084.60 ₹ 18,764.00 9.140.1

B 5 mm thick commercial ply conforming to IS : 1328 BWR type sqm 5.75 ₹ 784.35 ₹ 4,510.00 MR-1(AOR)

HARD WOOD BACKFRAMING

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position

with necessary stainless steel screws etc.

FLUSH DOOR SHUTTER

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board construction with frame of 1st class hard wood and

well matched commercial 3 ply veneering with vertical grains or cross bands and face

veneers on both faces of shutters:

A 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws sqm 9.50 ₹ 2,015.75 ₹ 19,150.00 9.21.1

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on

all edges of flush door shutters (over all area of door shutter to be measured).

Digitally signed by AMIT

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of

glass excluded) (overall area of door shutter to be measured):

A Rectangular or square 9.24.1

Providing and fixing cupboard shutter with 19mm thick one side decorative and other

side balancing lamination factory pressed BWP grade marine ply as per IS 710 of

approved brand including 2mm thick PVC edge banding tape with hot glue by edge

bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc.

complete as per direction of Engineerin-charge.(Payment of providing and fixing auto

closing hinges shall be paid separately)

Providing and fixing 19mm thick both side balancing lamination factory pressed BWP

grade marine ply as per IS 710 of approved brand boxes, shelves, racks, almirah,

cupboard and drawer etc. including necessary nails,screws etc. complete as per

direction of Engineer-in-charge.

Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic

type) of approved make/brand to cupboard shutters with full threaded steel screws

including making necessary recess in board and finished etc. complete as per direction

of Engineer-in-charge

NARROW STILE MORTISE LOCK WITH EPC

Providing and fixing Assa Abloy/ Geze/ Dorma 917 Narrow stile mortise dead lock having

35 mm Backset including Euro Profile Cylinders with Both Side Key - 70 mm (best make of

approved quality) for glazed aluminium auoustic doors including necessary cutting and

making good etc. complete.

SLIDE CHANNEL DOOR CLOSER

Providing and fixing Assa Abloy/ Geze/ Dorma TS 71 aluminium extruded section body

slide channel door closer, closing force adjustable size EN 3–4(door weight upto 36 kg to

80 kg and door width from 701 mm to 1100 mm), tested according to EN 1154 with

necessary accessories and screws etc. complete.

Providing and fixing stainless steel Grade 304 Assa Abloy/ Geze/ Dorma TDLH 8100 Lever

Handle with 6501 Roses,6612 Escutcheons,8mm Spindle with Fixing Screws for door

thickness 35-55 mm, Back to back fixing with suitable fixing accessories etc .complete as

per direction of Engineer-in-Charge

SS BALL BEARING HINGES

Extra for providing SS ball bearing hinges instead of ISI marked Stainless Steel butt hinges

bright finished of required size with necessary screws. (Shutter area to be measured).

Digitally signed by AMIT

Providing & fixing acoustic panels any size and shape in approved color and code no.

with Standard size & 9mm thickness. acoustic Panels should have Sound Absorption

coefficient (NRC) 0.94. Formaldehyde emission standards of GB18580-2001 class E1, it is a

green material with asbestos-free, non-toxic and tasteless gas under extreme

4.14 temperature, protecting the ozone layer, non-irritant and recyclable. acoustic panels sqm 25.00 ₹ 6,115.70 ₹ 152,892.50 MR-6

have to be Fire-resistant . Good insulation properties, to prevent transmitting the heat

from outdoor to indoor directly as partition or and ceiling, saving 35% of energy,

extending the life of air conditioning. acoustic panels are Light weight and allow free

cutting with paper knife.

Total Carried Over to Abstract for Sub Head: 4.00 Wood And P.V.C. Work : ₹ 245,255.00 ₹ 222,895.05

SH FLOORING WORKS 5.00

VITRIFIED FLOOR TILES

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of

5.1 approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 11.41

cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including

grouting the joints with white cement and matching pigments etc., complete.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of

0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin

per kg), including filling / grouting and finishing complete as per direction of Engineer-in-

WOODEN FLOORING

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron

screws complete with :

a Second class teak wood sqm 80.00 ₹ 4,187.95 ₹ 335,036.00 11.33.1

CARPET TILE FLOORING

Digitally signed by AMIT

Providing & fixing of Tufted / Textured / Graphic Loop Pile Carpet Tile flooring of

approved make & shade for Medium- Heavy duty Commercial applications, having pile

height of 9mm, tufted Weight of 24-26 oz/yd2, average density >7,000 oz/yd3 , 100%

Solution Dyed, 8.0 Stitches per Inch, 0.112 in Finished Pile Thickness, Primary Backing of

non-woven Environment friendly, Recyclable, PVC Free, with high recycled content

material. Fiberglass Reinforced Thermoplastic Composite Secondary Backing containing

not less than 39% post consumer and/or post industrial material content, Soil Protection,

Class I Radiant Panel confirming to ASTM E 648, NBS Smoke < 450 confirming to ASTM E

662, Must pass both Part 2 and Part 3 of AATCC 174 with a minimum of 90% reduction

both gram negative and gram positive bacteria and no macroscopic growth against

the fungi., Built-in Permanent Conductive Fiber Electrostatic Propensity of Less Than 3.5

kV, including covering of the laid carpet with 1mm. Thk plastic sheets, with proper taping

of the joints and shampooing of the carpet prior to handover all complete as per the

approved manufacturers specification and as per the direction of Engineer-in-charge.

Total Carried Over to Abstract for Sub Head: 5.00 Flooring Works : ₹ 366,424.00 ₹ 0.00

SH ROOFING WORKS 6.00

PLAIN GYPSUM BOARD CEILING

Providing and fixing false ceiling at all height including providing and fixing of frame

work made of special sections, power pressed from M.S. sheets and galvanized with zinc

coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle

cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm

centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm

long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50

mm of required length with nuts & bolts of required size and other end of angle hanger

fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm

centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with

tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall

be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips

made out of 2.64 mm dia x 230 mm long G.I. wire at every junction,

Digitally signed by AMIT

including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm

and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl

plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including

fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall

screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish

of tapered and square edges of the board with recommended jointing compound ,

jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on

both sides of joint and two coats of primer suitable for board, all as per manufacturer's

specification and also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as

per drawings, specification and direction of the Engineer in Charge but excluding the

cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011

(Board with BIS certification marks)

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of

approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of

99%, Light Reflectance ? 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire

Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-

Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120

gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size

15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of

length 600 mm to form grid module of size 600x600 mm suspended from ceiling using

galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6

dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-

shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along

The system should rest on periphery walls /partitions with the help of GI perimeter wall

angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with

help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws.

The exposed bottom portion of all T-sections used in false ceiling support system shall be

pre-painted with polyester baked paint, for all heights. The work shall be carried out as

per specifications, drawings and as per directions of the engineer-in-charge.

A With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7) sqm 34.00 ₹ 2,362.10 ₹ 80,311.00 26.27.2

Total Carried Over to Abstract for Sub Head: 6.00 Roofing Works : ₹ 134,056.00 ₹ 0.00

SH FINISHING 7.00

INTERIOR FINISHING

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to

prepare the surface even and smooth complete.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as

per manufacturers specifications :

Digitally signed by AMIT

Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of

Special primer applied @ 0.75 ltr /10 sqm

LIGHTWEIGHT GYPSUM PLASTER

Providing and applying 12 mm thick (average) premixed formulated one coat gypsum

lightweight plaster having additives and light weight aggregates as vermiculite/ perlite

7.3 respectively conforming to IS: 2547 (Part - 1 & II) 1976, applied on hacked / uneven sqm 10.00 ₹ 363.45 ₹ 3,635.00 13.78

background such as bare brick/ block/ RCC work on walls & ceiling at all floors and

locations, finished in smooth line and level etc. complete.

MELAMINE CLEAR POLISH

Polishing in high gloss/matt finish melamine clear polish on wood work in required

color/wooden shade texture with following process in the sequence as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand

paper of 160/180 nos.

2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st

coat and 2nd coat is allowed to dry for 8 to 12 hrs.

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample

water to remove excess sealer layer and make the surface further smooth after this wet

rubbing, then surface is applied with special grade melamine fillers to fill all the small and

big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a

light wet rubbing is done this surface is further allowed to dry for 12 hrs.

4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear

polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24

hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry

for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using

melamine clear polish and melamine thinner mixed in required proportion complete as

per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of

7.6 6 MM THICK LACQURED FACING

Providing & fixing 6 mm thick annealed SCG Planilaque Evolution (premium GRIHA rated

lacquered glass i.e. textured from saint gobin) with flat polished edge fixed to 5.5 mm

. thick plain MDF board backing with neutral silicone and/or double-sided adhesive pads

etc. ,including polishing/MTG all complete as per the drawing & directions of engineer-in-

7.7 BLACKOUT ROLLER BLINDS

#REF! Supplying and fixing of Blackout blinds to the following specs.

Black-out material fibre-glass coated fabric, 12 mils thick, 62 threads per sq in., 0.750 lbs

per sq in. (441g per sq mt.)

Operation: - Manual. Offset side-mounted metal chain operated

Mounting: Closure Box in metal

Digitally signed by AMIT

Shade Orientation: Regular roll, shade cloth falls at window side of roller

Configuration: Single band

The Fabric to be as per approved sample (Fabric should be Fire Retardent Certified).

Cellular Semi Opaque 100% Polyester Hardware SpecificationHeadRail: Head rail is 17

mm high and 47 mm wide, Thickness 1.00 mm. It is made up of powder coated high

strength aluminum alloy covered by two end caps made up of PVC.Drum & Cradle: They

are molded ABS components with high strength metalic drum which are meant for

controlling the lifting cord.Bottom Rail: This is Aluminum Extruded Rail Made up of High

Strength Aluminum alloy, Which is powder coated in white.Installation Bracket: It is made

up of mild steel with zinc plate.Bottom Rail End Cap: It made up of high strength

ABS.White Cord: It is made of Nylon braided non stretchable thread of 1.2 mm

thickness.PVC Slip : It is made up of high strength PVC of width 25 mm.Fabric: 100% spun

bonded non-woven polyester translucent fabric Pleat dimension 3⁄4” hexagonal cell with

a distinct air pockets Sanitized, Weight : 145 + 5% GSM, Thickness : 0.14 -0.17, colour

fastness of light – 4-5 Grade ( DIN EN ISO105-B02).

7.8 Providing & fixing Motor Mechanism nos 0.00 31019.00 0.00 MR-20

7.9 Providing & fixing Motor Remote 16 channel nos 0.00 26748.00 0.00 MR-21

Supplying and fixing of Room Signages in imp.aluminum profile with 3 mm acrylic

7.10 Gents/Ladies pictograph printed on canvas (Room Names/Exit Signage) - Include braile Nos 3.00 ₹ 816.00 ₹ 2,448.00 MR-22

letterings Size is 6"x10".

Total Carried Over to Abstract for Sub Head: .00 Interior Finishing : ₹ 49,457.00 ₹ 144,992.00

SH DISMANTLING AND DEMOLISHING 10.00

Demolishing existing stucture as actual & making site good for construction brick work

10.1 manually/ by mechanical means including stacking of serviceable material and disposal

of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

A In cement mortar LS 1.00 ₹ 20,000.00 ₹ 20,000.00

Total Carried Over to Abstract for Sub Head: 10.00 Dismantling And Demolishing : ₹ 20,000.00 ₹ 0.00

SH SANITARY INSTALLATIONS 11.00

11.1 Providing and fixing 6kg upvc pipe including all fittings

SANITARY INSTALLATIONS

Providing and fixing CP Brass Single Lever Sink Mixer with Swinging Spout (Table Mounted

11.2 Model) with 450mm Long Braided Hoses of quality & make as approved by Engineer in

A 15 mm nominal dia each 1.00 ₹ 6,008.65 ₹ 6,008.65 MR-24

Digitally signed by AMIT

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40

mm C.P. brass waste complete, including painting the fittings and brackets, cutting and

making good the walls wherever required

White glazed fire clay kitchen sink of size 600x450x 250 mm each 1.00 ₹ 3,302.95 ₹ 3,303.00 17.9.1

Total Carried Over to Abstract for Sub Head: 11.00 Sanitary Installations : ₹ 3,303.00 ₹ 9,048.65

SH WATER SUPPLY 12.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability

for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing

the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one

step CPVC solvent cement and the cost of cutting chases and making good the same

including testing of joints complete as per direction of Engineer in Charge. Concealed

work, including cutting chases and making good the walls etc.

A (a) 20 mm nominal outer dia Pipes Metre 50.00 ₹ 513.75 ₹ 25,688.00 18.8.2

B (b) 25 mm nominal outer dia Pipes Metre 20.00 ₹ 626.05 ₹ 12,521.00 18.8.3

12.2 Providing and fixing uplasticised PVC connection pipe with brass unions 18.21

A (i) 45 cm length 18.21.2

Total Carried Over to Abstract for Sub Head: 12.00 Water Supply : ₹ 38,414.00 ₹ 0.00

SH WATER PROOFING 13.00

INTEGRAL CEMENT BASED TREATMENT

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc.,

13.1 by applying cement slurry mixed with water proofing cement compound consisting of

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement

compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement

compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with

water curing for 48 hours.

The rate includes preparation of surface, treatment and sealing of all joints, corners,

junctions of pipes and masonry with polymer mixed slurry.

Total Carried Over to Abstract for Sub Head: 13.00 Water Proofing : ₹ 3,616.00 ₹ 0.00

Digitally signed by AMIT

Name of Work : ESTIMATE FOR RENOVATION OF CONFERENCE ROOM (508) AT NATIONAL HUMAN RIGHTS COMMISSION

I.NO DESCRIPTION UNIT QTY RATE AMOUNT CODE

SH FURNITURE 15.00

15.1 Providing and Placing of U-Shape 22 Seater Conference Table of Size 6900*2900*800(H). Nos 1.00 ₹ 298,318.00 ₹ 298,318.00 MR-27 1

Worksurface : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade

conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.

Understructure : Knock-down construction type made of 18mm Thick Pre-laminated OF EXTERIOR MAKE twin

board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded with matching 2 mm

thick PVC lipping. Aluminium alloy 63400 - WP profile connecting panels together, Plastic ABS access flap for

access to wires and cables.

Modesty Panel : Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade

conforming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent

metal strip provided below work surface, made of 0.8mm CRCA (cold rolled close annealed) as per IS

513,epoxy polyester powder coated (DFT 40-60 microns)

Wire Management : Panels made of 0.8mm CRCA MS IS:513, epoxy polyester powder coated (DFT 40-60

microns) . Provision to mount 6 module plate below worktop & Cutout on top with two piece injection

moulded plastic part polymer component onto worktop.

Providing and Placing of Revolving High Back Pure Leather Chair. Overall Dimensions of Chair Seat Height - 2

15.2 40.0 to 55.0 cm. Height -110-135.0 cm. Width & Depth of Chair as measured from base - min. Width-75.0 cm Each 0.00 ₹ 18,398.75 ₹ 0.00 MR-28

and min Depth-65 cm.

Elite High Back Chair .or equivalent model from approved make list .

SEAT ASSEMBLY: the injection molded plastic cushioned seat upholstered with pure leather and moulded

high resilience (hr) polyurethane foam of density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25

BACK ASSEMBLY: the cushioned seat size : 47.6 cm. (w) x 49.2 cm. (d)back size : 47.5 cm. (w) x 77 cm. (d) &

back made of pu foam with insitu molded ms e.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm,

upholstered with pure leather.

ARMRESTS: the armrest top moulded from polyurethane(pu), upholstered in pure leather and mounted on to

a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk m.s e.r.w tube

having chrome plated finish.the armrest height adjustable up to 6.5±0.5cm in 5 stepsactive bio-synchro

FRONT PIVOT SYNCHRO MECHANISM: the 360° revolving type adjustable tilting mechanism with front-pivot for

tilt with feet resting on ground, 5-position tilt limiter of seat/back tilting ratio of 1: 2, the mechanism housing

made up of high density powder coated, 4 seat depth adjustment integrated in the seat through a sliding

mechanism. seat depth adjustment range of 6.0±0.5 cm

BACK HEIGHT ADJUSTABILITY: back frame connected to the up/dn mechanism housed in plastic t spine,

adjusted in the range of 7.42±0.5 cm

SLIDING SEAT MECHANISM : Seat slide horizontaly having Stroke of seat slide is 5 cm.

PNEUMATIC HEIGHT ADJUSTMENT: The pneumatic height adjustment has an adjustment stroke of 10.0 ± 0.3

PEDESTAL ASSEMBLY WITH CASTORS: The High Pressure Die cast polished Aluminium pedestal, fitted with 5

nos. injection moulded in black PP twin wheel castors. The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ±

15. Providing and Placing of modular workstation size 2000x600 Each 1.00 ₹ 28,000.00 ₹ 28,000.00 MR-30

Digitally signed by AMIT

NHRC :- HVAC WORK

I.NO DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT CODE

SH OUTDOOR UNIT 1.00

Supply Installation, Testing & Commissioning of modular type Variable

Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units

suitable for cooling and heating, having all hermetically sealed

inverter type Scroll Compressor(s), minimum two compressors for

above 14 HP modules, microprocessor based Controller, top

discharge type condensing unit(s), with R 410 A Refrigerant, vibration

isolators, with suitable foundation etc. complete as required. The unit

shall deliver the rated capacity at AHRI Conditions and work even at Per HP 20 ₹ 16,415 ₹ 328,300 1

50°C ambient temperature without tripping. The unit shall be suitable

to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall

be filled with first charge of the refrigerant and ready for use as

required. The COP at AHRI conditions shall not be less than 3.1 and

IEER not less than 6.5 .

Total Carried Over to Abstract for Sub Head: 1.00 Outdoor Unit :

SH INDOOR UNIT-CASSETTE TYPE 2.00

Supply, installation, testing and commissioning of following

minimum capacity 4-way flow VRV/VRF Cassette Type Indoor

ceiling mounted unit equipped with synthetic washable media

pre-filter, fan section with low noise fan/dynamically balanced

blower, multispeed motor, coil section with DX Copper coil,

electronic expansion valve, outer cabinet, drain pump, grill,

necessary supports, vibration isolation, cord less remote control

etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC 2

supply, complete, as required. The unit shall have automatic

force shut down provision in case of fire on receiving signal from

BMS System. The cooling capacity of indoor unit will be at air inlet

conditions of 27 Degree C DB and 19 Degree C WB temperature.

2.4 2.4 TR capacity Cassette Unit Each 4 ₹ 31,453 ₹ 125,812 2.6

Total Carried Over to Abstract for Sub Head: 2.00 Indoor Unit-

Cassette Type :

SH INDOOR UNIT-HIGH WALL TYPE 3.00

Supply, installation, testing and commissioning of following

minimum capacity VRV/VRF Highwall type Indoor unit equipped

with washable synthetic media pre-filter, fan section with low

noise fan/dynamically balanced blower, multispeed motor, coil

section with DX copper coil, electronic expansion valve, outer

cabinet,cord less remote control, drain pan, necessary

accessories etc., suitable for operation on 230 V ± 10%, 50Hz,

single phase AC supply, complete as required. The unit shall

have automatic force shut down provision in case of fire on

receiving signal from BMS System.The cooling capacity of indoor

unit will be at air inlet conditions of 27 Degree C DB and 19

Degree C WB temperature.

Total Carried Over to Abstract for Sub Head: 3.00 Indoor Unit-

High Wall Type :

SH Inline Fans 4.00

Supplying, Installing, Testing and Commissioning of Inline fans

complete with motor, supporting frame, gravity louvres,etc. as

4.1 per drawings and specifications.

Total Carried Over to Abstract for Sub Head: 4.00 Inline Fans :

SH COPEER REFRIGERANT PIPING 5.00

Supply, Installation, testing and commissioning including

vaccumiazation and Nitrogen testing of following nominal sizes

of soft/hard drawn copper refrigerant piping for VRV/VRF system,

complete with fittings, with suitable adjustable ring type hanger

supports, jointing/brazing including accessories, insulated with

Class-O tubular insulation/with Class-O closed cell elastometric

nitrile rubber tubular sleeves sections of specified thickness as

given below for Suction and Liquid lines, all accessories as per

5.1 specifications etc. as required :

6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

5.1.1 mm thick insulation

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19

5.1.2 mm thick insulation

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with

5.1.3 19 mm thick insulation Digitally signed by AMIT

I.NO DESCRIPTION UNIT QTY RATE DSR AMOUNT NDSR AMOUNT CODE

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with

5.1.4 19 mm thick insulation

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19

5.1.5 mm thick insulation

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with

5.1.6 19 mm thick insulation

25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with

5.1.7 19 mm thick insulation

Total Carried Over to Abstract for Sub Head: 5.00 Copeer

Refrigerant Piping :

SH Drain Piping 6.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings, including fixing the pipe

with clamps at 1.00 m spacing. This includes jointing of pipes &

fittings with one step CPVC solvent cement and testing of joints

complete as per direction of Engineer in Charge.

6.1.1 25 mm nominal dia Pipes RM 28 ₹ 150 ₹ 4,200 MR-2

6.1.2 19mm insulation RM 35 ₹ 120 ₹ 4,200 MR-3

Total Carried Over to Abstract for Sub Head: 6.00 Drain Piping : ₹ 0.00 ₹ 8,400.00

SH DUCTING, GRILLS, DIFFUSER AND INSULATION 7.00

Supply, installation, balancing and commissioning of factory

fabricated GSS sheet metal rectangular/round ducting

complete with neoprene rubber gaskets, elbows, splitter

dampers, vanes, hangers, supports etc. as per approved 16.12.1

drawings and specifications of following sheet thickness

7.1 complete as required.

Supplying & fixing of powder coated extruded aluminium Return

Air Grills with louvers but without volume control dampers Sqm 1 ₹ 5,507 ₹ 5,507 16.16

7.2 complete as required.

Supplying, fixing testing commissioning of Return air diffusers of

powder coated aluminium without volume control dampers with Sqm 1 ₹ 7,559 ₹ 7,559 16.18

7.3 anti smudge ring & removable core.

Total Carried Over to Abstract for Sub Head: 7.00 Ducting, Grills,

Diffuser And Insulation :

Total HVAC Value ₹ 606,093.00 ₹ 39,457.00

Digitally signed by AMIT

(C1: Internal Electrical Installation)

S. No. Description Rate Unit Amount Remarks

1) Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable in

surface / recessed steel conduit, with modular switch, modular plate,

suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable etc. complete as required.

2) Wiring for group controlled (looped) light point/fan point/exhaust fan

point/ call bell point (without independent switch etc.) with 1.5 sq. mm

FRLS PVC insulated copper conductor single core cable in surface/

recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS

PVC insulated copper conductor single core cable etc. complete as

3) Supplying and fixing suitable size GI box with modular plate and cover in 10 ₹ 477.00 Each ₹ 4,770.00 DSR 1.31

front on surface or in recess, including providing and fixing 3 pin 5/6 A

modular socket outlet and 5/6 A modular switch, connections etc.

complete as required.

4) Supplying and fixing suitable size GI box with modular plate and cover in 8 ₹ 586.00 Each ₹ 4,688.00 DSR 1.32

front on surface or in recess, including providing and fixing 6 pin 5/6 &

15/16 A modular socket outlet and 15/16 A modular switch, connections

etc. complete as required.

5) Supplying and fixing following modular switch/ socket on the existing

modular plate & switch box including connections but excluding modular 1.24

plate etc. as required.

3 pin 5/6 amp socket outlet 20 122.00 Each ₹ 2,440.00 1.24.4

6 pin 15/16 amp socket outlet 5 197.00 Each ₹ 985.00 1.24.5

6.0) Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in

the existing MCB DB complete with connections, testing and

commissioning etc. as required.

7.0) Supplying and fixing following way, vertical type three pole and neutral,

sheet steel, MCB distribution board, 415 volts, on surface/ recess,

complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, 2.5

interconnections, powder painted including earthing etc. as required.

(But without MCB/RCCB/Isolator)

8.0) Supplying and fixing following rating, double pole, (single phase and

neutral), 240 volts, residual current circuit breaker (RCCB), having a

sensitivity current upto 300 milliamperes in the existing MCB DB 2.14

complete with connections, testing and commissioning etc. as required.

9 Supplying and fixing of following sizes of steel conduit along with

accessories in surface/recess including painting in case of surface

conduit, or cutting the wall and making good the same in case of

recessed conduit complete as required.

10) Wiring for circuit/ submain wiring alongwith earth wire with the following

sizes of FR PVC insulated copper conductor, single core cable in 1.14

surface/ recessed steel conduit as required

2 X 4 sq. mm + 1 X 4 sq. mm earth wire 100 334.00 Metre ₹ 33,400.00 1.14.3

4 X 10 sq. mm + 2 X 6 sq. mm earth wire 0 1005.00 Metre ₹ 0.00 1.14.10

Digitally signed by AMIT

11) Supplying and fixing of following sizes of steel conduit along with

accessories in surface/recess including painting in case of surface

conduit, or cutting the wall and making good the same in case of

recessed conduit as required.

SH-VI LIGHTING FIXTURES & OCCUPANCY SENSOR

12.0) Supply, installation, testing and commissioning of the following fixtures

with all accessories including drivers, LED Lamps complete etc. as

required. Including Dimmable ballasts (DALI)

a. LED indoor surface downlighter having pressure die-cast Al housing 20 ₹ 1,889.03 Each ₹ 37,780.60 MR-20

with diffused optics. The luminaire should have CRI > 80 and CCT of

4000K. The luminaire shall be compliant with IP20, IK02

classification.The fixture should have a minimum system efficacy of 110

lumen/Watt and a minimum system lumen output of 1200 lumens and

maximum system wattage of 11 Watts.. The electronic driver used shall

have a power factor >0.95 , THD <10%.The Luminaire shall be with

LM79 and LM 80 certifications given by NABL/UL accredited lab, Fixture

and Driver to have separate BIS approval.Including Dimmable ballasts

c. Recessed mounted 2X2 LED panel ,made of CRCA housing with high 12 ₹ 7,293.00 Each ₹ 87,516.00 MR-21

efficiency PS Diffuser. LED Used shall be SMD type and fixture should

have minimum efficacy at System level >=120 lumens/watt with

Minimum system Lumens 3000 & Max System wattage of 25W, CCT of

4000K (SDCM<=5), CRI Ra >=80, THD<10%, PF >0.95, an operating

Voltage Range of 140 - 270 VAC.Minimum Internal Surge Protection

4.0KV & IP20/IK02 protection,The Luminaire shall be with LM79 and LM

80 certifications given by NABL/UL accredited lab, Fixture and Driver to

have separate BIS approval.Including Dimmable ballasts (DALI)

13.0) DIMMIMG SYSTEM

Supply of the following LED light fixtures with all accessories, such as,

Dimmable ballasts (DALI), complete.

OCCUPANCY SENSOR

1) Supplying,installation,testing and commissioning of Passive Infrared 4 ₹ 4,602.00 Each ₹ 18,408.00 DSR 15.1

(PIR) technology based occupancy sensor having high prefoMetreance,

non regulating programmable type, suitable for connected load upto

10Amp , for mounting height up to 2.8 mtr and for 5 m diameter

coverage area along with necessary fixing arrangements i/c

programming at site etc. complete as required

2) Supplying,installation,testing and commissioning of Passive 4 ₹ 9,171.00 Each ₹ 36,684.00 DSR 15.2

Infrared(PIR) technology based occupancy sensor with day light

dimming(lighting level shall be regulated as per availability of natural day

light in an area along with occupancy detection.) having high

prefoMetreance, regulating programmable type, suitable for connected

load upto 10Amp, for mounting height up to 2.8 mtr and for 5 m diameter

coverage area along with necessary fixing arrangements i/c

programming at site etc. complete as required.

Total of C1: Rs. ₹ 561,983.60

Digitally signed by AMIT

S.No. Item Specifications Unit Qty Price Amount

Supplying, Installation, testing & commissioning of Fine Pitch LED Video

Wall Screen with size (Approx) 3064 (W) x 1832 (H) x 31 (D)), having

pixel pitch 1.588 mm or better with Magnalium cabinet in 16:9 aspect

1 ratio , brightness calibrated (max) 800 Nits complete with video wall Nos 1 ₹ 2,560,000.00 ₹ 2,560,000.00

controller , refresh rate 3840 Hz or more BIS certified compatible for

connection to wireless presentation device complete as per direction of

Engineer-in-charge. LED cabinet should be BIS certified.

Supply, Installation, testing and commissioning of 43 inch UHD

Display|250 Nits Brightness |20000:1 Contrast Ratio | Operation:

2 24x7|1xVGA; 2xUSB 2.0 , 4x HDMI 2.0 In, Secure USB 2.0, 1xHDMI 2.0 Nos 2 ₹ 55,000.00 ₹ 110,000.00

out, USB-Autoplay, , HDMI-Wakeup, Auto-switch on Failover, Panel

Lock, OSD Rotation, NoSignalPowerOff, Screen Saver, Etc.

Supply, Installation, testing and commissioning VC End Point with 20X

Camera, Mic, remote, NTSC/PAL; Cables: 2 HDMI 1.8m, 1 CAT 5E LAN

3.6m, 1 CAT 5E SHLD 25ft, 1 HDCI 6ft, 1 HDCI Mini 3m, Power: India BIS.

Maintenance Contract Required.

Supply, Installation, testing and commissioning of Gooseneck

Microphone, it should be pre-polarised condenser microphone having

Cardioid or better polar pattern, shall have frequency response of 50Hz

Wired to 20kHz, length of the gooseneck shall be more than 420mm, Should

4 Goosenec have Max SPL Level of 128dB or more, it should support phantom Nos 23 ₹ 75,000.00 ₹ 1,725,000.00

k Mic power from 12v to 48v, Should come with base having programmable

mute/unmute button, Should be RF interference free from other

wireless devices, should have muted/unmuted status LED Indication etc

complete required as per the specifications.

Supply, Installation, testing and commissioning of wireless digital

Handheld Handheld Microphone with 18 or more channel, RF output 100mW or

more, super cardiod pickup pattern, Frequency range : 1880 to 1930

Micropho MHz, Connectivity : RJ-45, 256-bit AES Encryption (specifications

ne includes single microphone set of transmitter and receiver) etc and

complete as required.

Supply, Installation, testing and commissioning of wireless digital

microphone charger, charging capacity : 2 or more simultaneously with

lighting indication, Should be from same OEM as of wireless mic etc

and complet required as per specifications.

Suppy Installation Testing and Commissioning of digital signal processor

with minimum 14no. Or more Mic / line input with phantom power and

AEC and 8 or more line level output, 1no. Or more GPIO at least 2

channel of USB input and output for software Video Conferencing,

should have 64x64 channel of digital dante input output, Should have

sampline rate of 48kHz or better, Should be expandable for port

expansion, should support Control with App via iOS and Android

devices, or any third-party control system, Shall have Built-in filters,

feedback suppression, AGC etc complete as required as per

Supply, Installation, testing and commissioning of Quad channel energy

star rated digital power amplifier,Quad channel 4 Ohm or 8 ohm

energy-efficient amplifier - 4 x 30W or more 70/100V Technology :

8 Amplifier Class-D,Input linking through miniature switches, Switching mode Nos 1 ₹ 176,832.44 ₹ 176,832.44

power supply, Protection : DC Short circuit & Over heating & Over load

& Signal limiting, Frequency Response 120 Hz - 20 kHz or better, Silent

passive cooling etc complete required as per specifications.

Supply, Installation, testing and commissioning of 6.5" two-way coaxial

thin edge ceiling loudspeaker, 100V transformer power taps : 24,12,6,

watts, Conical dispersion : 145° or more, impedance : 8, low impedance

RMS continous power : 30watts, frequency range : 50 Hz - 20 kHz or

better, frequency response : 60Hz - 20KHz or better etc complete

required as per specifications.

Digitally signed by AMIT

Supply Installation Testing and Commissioning of surface-mount USB-

to-Dante endpoint, two-way volume and mute sync for Microsoft

Teams,compliant with CE and FCC, device shouold have Power-over-

USB to Ethernet (PoE) to IEEE 802.3af Class 0 standard and support Dante

10 Dante networking using standard CatX cable, device should support the Nos 1 ₹ 136,500.04 ₹ 136,500.04

converter Speakerphone profile with and without echo cancellation, enable two-

way volume and mute syncronization with both PC and Mac platforms,

Dante with AES67 compliance,Sampling Rate(s) 48 kHz,should be from

same OEM as DSP etc complete required as per specifications.

Suppy Installation Testing and Commissioning of control system with

touch panel/Ipad

Supply, Installation, testing and commissioning of Eight HDMI inputs

matrixed to Eight HDMI outputs with HDMI 2.0a specification and

12 18Gbps (600MHz) 4K UHD support, HD resolutions up to Nos 1 ₹ 420,000.00 ₹ 420,000.00

bit Deep Color up to 1080p@60Hz.

Supply, Installation, testing and commissioning of HDMI RX extender

with complies with the advanced HDCP 2.2 and HDMI 2.0 standards,

uncompressed HD audio and video as well as control via a single run of

Cat.5e/6/7 cable over distances of up to 70 meters and upto 40mat 4K,

HDBaseT feature support: HD Video and Audio, and Control (IR/RS-232

pass-through) and CEC bypass, Supports pass-through of many audio

formats including LPCM (up to 8 channels), Bitstream and HD Bitstream

Supply, Installation, testing and commissioning of HDMI TX extender

complies with the advanced HDCP 2.2 and HDMI 2.0 standards,

uncompressed HD audio and video as well as control via a single run of

Cat.5e/6/7 cable over distances of up to 70 meters and upto 40mat 4K,

HDBaseT feature support: HD Video and Audio, and Control (IR/RS-232

Transmitt pass-through) and CEC bypass, Supports pass-through of many audio

er formats including LPCM (up to 8 channels), Bitstream and HD Bitstream

Supply Installation Testing and Commissioning of HDMI Audio Extractor

should extract up to 2 channels of LPCM audio or 5.1 channels of

Bitstream audio from an HDMI source, allowing the user to convert high

quality HDMI audio into more convenient analog (LPCM 2.0 sources

only) or optical signals for use with powered speakers or non-HDMI AV

receivers. Both the input and output HDMI ports should support 4K

HDMI UHD resolutions up to 4K@60Hz (4:4:4, 8-bit) and should capable of

15 Deembed providing high quality audio and video performance. The unit should Nos 1 ₹ 53,100.00 ₹ 53,100.00

der supports passthrough of HD and standard Bitstream formats as well as

LPCM 7.1 with audio sampling rates up to 192kHz. Built-in EDID

management support allows the user select from multiple EDIDs and,

with the use of optional PC software, to upload, download, or edit EDID

files etc and complete as required

Supply of Recording, Streaming & Webcasting Hardware

simultaneously, Built-in HDMI, 3G-SDI, IP & USB 3.0 Video Inputs with

1x Line In and 1x XLR Input, 2x HDMI Outputs, Can record upto any two

inputs simultaneously in a single frame and as well as individual sources

16 simultaneously. Should have minimum 1TB inbuilt storage and can be Nos 1 ₹ 351,000.00 ₹ 351,000.00

connected to local NAS storage. The system should be able to support

minimum 3 unicast streams.The recorded files should have the option

of time and date stamp. OEM should be CE, FCC & RoHS Certified

Supply, Installation, testing and commissioning of wireless presentation

18 Supply, Installation, testing and commissioning of 16 port switch Nos 1 ₹ 53,100.00 ₹ 53,100.00

Cable Supply, Installation, testing and commissioning of Cable cubby (1

cubby HDMI, 1LAN,1 Charging socket)

20 24U AV equipment rack Nos 1 ₹ 14,750.00 ₹ 14,750.00

21 Cables Cables & connectors Lot 1 ₹ 150,000.00 ₹ 150,000.00

CCTV Device With 4mp Cam

(To feed the conference room live streem to control room)

Total Cost of AV Work 1 ₹ 10,221,319.78

Digitally signed by AMIT