REPAIRS TO AC SHEET, ROOFING, FALSE CEILING, JOINERY, FLOORING AND CONNECTED WORKS AT HATTIGOR MILITARY STATION UNDER GE RANGIA

Amount

Dismantling Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings, complete all as specified and as directed by Engineer-in-charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation,etc) or insulation board/Slabs/blankets of any thickness including cover fillets, complete all as specified and as directed by Engineer-in-charge.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing, complete all as specified and as directed by Engineer-in-charge.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc., complete all as specified and as directed by Engineer-in-charge.

Demolition of unreinforced cement concrete in ground floors and pavings nexc 15 cm thickness (below or above ground level) complete all as specified and as directed by Engineer-in-charge.

Dismantling Unframed timber scantlings 40 Sqcm and over in section and in any position, complete all as specified and as directed by Engineer-in-charge.

Dismantling of unframed fillets, rails, posts, rafters, purlins etc., under 40 Sqcm in section, complete all as specified and as directed by Engineer-in-charge.

Dismantling boarding, any description fixed in any position with nails, complete all as specified and as directed by Engineer-in-charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as per specified and as directed by Engineer-in-charge.

Taking down shutters of any description not exc. 1 sqm each, complete all as specified and as directed by Engineer-in-charge.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each, complete all as per specified and as directed by Engineer-in-charge.

Taking down chowkat or frame not exceeding 1.5 Sqm each (without taking off shutter from the frame), complete all as specified and as directed by Engineer-in-charge.

Taking down chowkat or frame exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutter from the frame), complete all as specified and as directed by Engineer-in-charge.

Demolition of brick work built in any cement mortar complete all as specified and as directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated or semi-corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as specified and as directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws or J hooks, complete all as specified and as directed by Engineer-in-charge.

M&L 6 mm thick Asbestos Cement sheet, corrugated, or semi corrugated sheets in roofs, walls etc. and fixed with fixed with L-type or J-type or cranked hook bolts, complete all as specified and as directed by Engineer-in-charge.

M&L for 6 mm thick asbestos cement two pieces adjustable serrated ridge for corrugated, or semi corrugated sheets fixed with L-type or J-type or cranked hook bolts, complete all as per specified and as directed by Engineer-in-charge.

Fixing only Asbestos Cement sheet, corrugated, or semi corrugated sheets in roofs, walls etc. and fixed with L hook or Cranked bolts (except sheets), complete all as specified and as directed by Engineer-in-charge.

S&F solid PVC wall paneling consisting of 5 mm thick PVC wood grain printed PVC sheet inclusive of solvent cement and fixing at site as per specification and directed in any position with screws, complete all as per specified and as directed by Engineer-in-charge.

S&F 5mm thick PVC sheet fillets of width 35mm for wall paneling inclusive of fixing on wall to make frame as per specifications and drawing, complete all as per specified and as directed by Engineer-in-charge.

M&L for 4mm thick asbestos cement plain building boards, fixed to timber frame work with screws as in walls complete all as specified and as directed by Engineer-in-charge.

M&L for 4mm thick Non asbestos fibre cement building boards fixed or laid/inserted to timber/GI/Aluminium framework with screws as in ceiling and applying on one coat of distemper oil emulsion, complete all as per specified and as directed by Engineer-in-charge.

M&L second class hard wood plain fillets, square or rectangular or triangular in section, clean sawn, secured with nails or brads having sectional area not exceeding 03 sqcm complete all as specified and as directed by Engineer-in-charge.

M&L second class hard wood plain fillets, square or rectangular or triangular in section, clean sawn, secured with nails or brads having sectional area exceeding 6 sqcm but not exceeding 13 sqcm complete all as specified and as directed by Engineer-in-charge.

M&L second class hard wood plain fillets, square or rectangular or triangular in section, clean sawn, secured with screws or brads having sectional area exceeding 13 sqcm but not exceeding 25 sqcm complete all as specified and as directed by Engineer-in-charge.

M&L for 15 mm thick rendering on fair faces of brick work or one side of lathing in cement mortar (1:4) and surface to be finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

M&L rendering 10mm thick on other than fair faces of brick work or on other side of lathing in cement mortar 1:6, surface to be finished fair & even without using extra cement, complete all as specified and as directed by Engineer-in-charge.

M&L for G.I. wire netting 0.9 mm dia and 12 mm mesh lathing to wood or metal studding, joists, etc., in walls, ceilings, stanchions, beams, etc., including all laps, cutting and waste, complete all as specified and as directed by Engineer-in-charge.

M&L 40 mm thick cement concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) as in floors, finished even and smooth without using extra cement, complete all as per specified and as directed by Engineer-in-charge.

M&L 75 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) in flooring/ hard standing/pavings/plinth protections, finished even and smooth without using extra cement complete all as per specified and as directed by Engineer-in-charge.

M&L for Glass dividing strips, 38 x 3 mm thick and inserted in position to confirm to design, complete all as per specified and as directed by Engineer-in-charge.

M&L 2nd class hard wood in scantling wrought timber unframed and fixed, complete all as specified and as directed by Engineer-in-charge.

M&L 20 mm thick second class hard wood boarding with butt joints fixed with nails in any situation (except flooring and skirting), complete all as specified and as directed by Engineer-in-charge.

S&F coloured non-skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shades of tiles over 15 mm thick screed bed or bedding layers in CM 1:4 complete all as per specified and as directed by Engineer-in-charge.

M&L for Coloured Glazed ceramic tiles 300 x 200 x 6 or 7 mm thick on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick screed in CM (1:4) complete all as per specified and as directed by Engineer-in-charge.

M&L for vitrified ceramic tiles 8 to 9 mm thick of light shade (square/rectangular) polished area of each tile not exceeding 0.36 sqm in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shades of tiles over 15 mm thick screed bed or bedding layers in CM 1:4 complete all as per specified and as directed by Engineer-in-charge.

M&L precast coloured cement concrete chequered tiles 300x300x25mm thick set jointed and pointed in with grey cement and pigment laid over and including 20mm thick screed bed in CM 1:6 in floorings, complete all as per specified and as directed by Engineer-in-charge.

S&F 35 mm thick plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkats complete all as per specified and as directed by Engineer-in-charge.

S&F 35 mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides, complete all as per specified and as directed by Engineer-in-charge.

M&L 35 mm thick second class hardwood glazed and skeleton shutter open rebated and prepared to receive glass, gauge etc (without sash bar) edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) complete all as specified and as directed by Engineer-in-charge.

S&F second class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as per specified and as directed by Engineer-in-charge.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet rainforced with MS square tube in opening including taking down old unserviceable frame along with shutter, complete all as per specified and as directed by Engineer-in-charge.

Supply and fixing factory made solid panel factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as per specified and as directed by Engineer-in-charge.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc. 6m mean radius in cement mortar 1:6, complete all as per specified and as directed by Engineer-in-charge.

M&L for brick work with sub-class `B' old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and as directed by Engineer-in-charge.

S&F powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. including taking down old unserviceable Al frame with shutter complete all as specified and as directed by Engineer-in-charge.

S&F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading, screws, etc. complete all as specified and as directed by Engineer-in-charge.

S&F powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.), hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and as directed by Engineer-in-charge.

S&F 3 mm thick sheet glass, ordinary quality in squares not exceeding 0.5 Sqm in each pane fixed with cut & mitred beads, complete all as specified and as directed by Engineer-in-charge.

S&F Stainless steel wire cloth, 0.56 mm dia of wire and average width of aperture 1.18 mm and fixed with tinned tacles or galvanised wire staples, complete all as specified and as directed by Engineer-in-charge.

S&F in repair stainless steel wire cloth, 0.56 mm dia of wire and average width of aperture 1.18 mm and fixed with tinned tacles or galvanised wire staples, complete all as specified and as directed by Engineer-in-charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads, complete all as specified and as directed by Engineer-in-charge.

S&F 125mm long aluminium anodised barrel tower bolts of extruded section, complete all as specified and as directed by Engineer-in-charge.

S&F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section, complete all as per specified and as directed by Engineer-in-charge.

S&F 100 mm long stainless steel butt hinges medium weight cold rolled, complete all as per specified and as directed by Engineer-in-charge.

S&F 75 mm long stainless steel butt hinges medium weight cold rolled, complete all as per specified and as directed by Engineer-in-charge.

S&F 150 mm long extruded Aluminium alloy handles, fabricated type, anodised, complete all as per specified and as directed by Engineer-in-charge.

S&F 75 mm long extruded Aluminium alloy handles, fabricated type, anodised, complete all as per specified and as directed by Engineer-in-charge.

S&F aluminium alloy 300 mm anodised sliding door bolts with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast - aluminium alloy, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously untreated wood or wood based surfaces of any description, exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new or previously untreated wood or wood based surfaces of any description, not exceeding 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed by Engineer-in-charge.

M&L for preparing new plastered surfaces and applying two coats of cement base paint on walls, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing new plastered surfaces and applying two coats of oil bound distemper on walls including one coat of chalk whiting primer, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing AC wall board & applying two coats of white wash, complete all as per specified and as directed by Engineer-in-charge.

M&L for preparing AC ceiling board & applying two coats of white wash, complete all as per specified and as directed by Engineer-in-charge. Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ.

M/S SITAL BUILDERS