Construction of Office building and staff quarters Agriculture Department at Chambaghat Distt Solan HP Sub Head Civil work/ WSandSI and EI work

Amount

Cutting in earth work in all kinds of soil such as pick, jumper, blasting/chiselling/wedging out hard/soft rock and disposal of excavated earth in all leads and lifts through manually means and as per the direction of Engineer-in-Charge and stacking of useful stones in specified dimension.

Clearing Jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30cm measure at hight 1m above ground and removal of rubbish upto a distance of all lead and lift outside the periphery of area cleared.

Excavation in foundations, trenches etc., in earth work, in all kinds of soil such as pick work, jumper work, blasting/chiseling/wedging out of soft/hard rock in all depths including pumping and bailing out water and stacking the excavated in specified manner clear from the edge of the excavation and then returning the stacked soil in 15 cm. layers, foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer-in-Charge

Excavation in earth work and feeling in 15 cm layers in foundation and plinths including raimming, and watering and consolidating within all lead and lift.

Filling in plinth with sand under floors including watering, ramming consolidating and dressing complete including carriage of material in all leads and lifts.

Disposal of earth by mechanical trasport with loading & unloading and drassing complete. (upto 10 Km)

Providing form work with steel plates 3.15 mm thick welded with angle iron in frame 30x30x5 mm so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies for all height of propping and centering below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work including carriage of materials in all leads and lifts. a) Foundation, footings, basis of columns and mass concrete.

b) Flat surfaces such as soffits and suspended floor, roofs landing and like plain upto 200 mm in thickness.

c) Columns, pillars, posts and struts square, rectangular in plain.

d) Stair cases ( except spiral stair case) excluding landing but including preparing of the surface and finishing of nosing upto floor two level.

e) Beams, cantilever, girders and lintel:- Side of soffits of beam, beams haunching cantilevers bressumers and not exceeding 1 meter in depth in all heights from floor.

g) Vertical surface such as wall (any thickness partitions and the like including attached pilasters, plinth and string course of the like.

f) Edges of slab & breaks in floor upto 200 mm width

Providing and laying cement concrete 1:4:8 (1cement:4sand:8graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in foundation and plinths including carriage of materials in all leads and lifts.

Providing and laying cement concrete 1:6:12 (1cement:6sand:12graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in foundation and plinths including carriage of materials in all leads and lifts.

Providing and laying cement concrete 1:2:4 (1cement:2sand:4graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work including carriage of materials in all lead, lift

Providing and laying cement concrete 1:1.5:3 (1cement: 1.5 sand: 3 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of materials in all leads, lifts and upto all heights. a) Foundation, footings, basis of columns and mass concrete.

b) Staircase (except spiral stair cases) excluding landing but including preparing of the surfaces and finishing of nosing.

c) Suspended floors, roofs, landings, shelves and their supports balconies beams, girders bressumers and cantilevers.

d) columns, pillars, posts and struts circular or rectangular in plan.

c) Wall any thickness but not exceeding 0.10 meter thickness) including attached buttresses pilasters and their caps string courses etc. from top of foundation level upto floor two level and above.

Providing mild steel/tor steel reinforcement for RCC work including bending, binding also cost of binding wire and placing in position complete upto all floor level including carriage of materials in all lead and lifts. a) Tor steel (TATA steel)

Providing and fixing reinforced concrete (GRC) Jaali in approved shade size patten, design, thickness and color by spraying method using specialized equipment (power spray machines to attain the optimum strength) allowing simittaneous deposition of kinown quantities of cementitions slurry and chopped glass fiber. The screens should be made from grade white portland cement quartz fine silica sand, alkali resistant glass fiber manufectured by saint Gobain or equinalent super plasticizers mmanufecture by BASF or polymers manufecture by Bayefox-(Germany) or equivalent. The meterials casting should take place in synthetic rubble/FRP mould manufectured byrecki or equivalent. The fixing should be dry type i.e. to be done with SS-304 Grade l Shaped clamps, desh fasteerners and pins/ anchors as per the direction of the architect/ engineer in charge. The work to be carried out all height depts " The casted screen moulds must be stored under controlled tempratures ranging in between 5 degree celsius -45 degree celsius moulds must be stacked on a level surface in such a manner that they do not now twist. The GRC componant must not be demoulded until it has gained sufficient strainth to be removed from mould. The time required is temparature dependant. It rainges between -36 hours GRC should be loosely covered over night and should be dry cured after be demoulding that moist curing can be done for a period for a period of days using the curing pound available at the manufactured facility. Design and size as per including carriage of materials in all leads, lifts

Brick work 2nd class using common burnt clay building bricks in foundation and plinth 1:6 (1cement:6sand) including carriage of materials in all leads, lifts and upto all heights.

Brick work 2nd class using common burnt clay building bricks in superstructure above plinths level in cement mortar 1:6 (1cement:6sand) including carriage of materials in all leads, lifts and upto all heights.

Half brick masonry in common burnt clay building bricks 2nd class in rerstructure in cement mortar 1:4 (1cement:4sand) including carriage of materials in all leads, lifts and upto all heights.

Extra for providing and placing in position 2 Nos. 6 mm dia MS bars at every third course of half brick masonary (with FPS bricks)

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (1cement:6sand:12 graded stone aggregate 20 mm nominal size) at plinth level in cement mortar 1:6 (1 cement:6sand) including carriage of materials in all leads, lifts and upto all height in breast and retaining walls.

Stone soling under floor dry hand packed properly filling interstices with consolidating i/c ramming manually including carriage of materials in all lead & lifts.

Stone filling behind retaining wall including carriage of materials in all lead & lifts and height.

Square rubble masonary coursed with hard stone of approved quality in superstructure in retaining wall/breast walls including raking out joints, including carriage of materials in all lead & lifts. In cement morter 1:6 (1Cement : 6 sand).

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line level and curvature jointed with cement morter 1:3 (1 cement :3 coarse sand) including making joints with or without grooves (thickness of joints except to sharp curve shall not to more than 5mm) including making drainage opening wherever required complete etc ( Precast C.C. kerb stone shall be approved by Engineer In Charge) including carriage of materials in all lead & lifts and height.

Providing wood work in frames of doors, windows and other frames wrought framed and fixed in position in Ist class Sal wood including carriage of materials in all lead, lifts and upto all heights.

Providing and fixing panelled glazed or paneled and glazed shutters for doors windows and clerestory windows including black enameled iron butt hinges with necessary screws including carriage of materials in all leads, lifts and upto all height 40 mm thick, Ist class deodar wood.

Providing and fixing flish door shutters core of black board construction with frame of first class hard wood and well matched first class indian teak ply veneering the vertical grains of cross bend and face vaneers on one face and commericail ply veneering with vertical grains of cross bend on other face of shutters 40mm thick including black enamelled MS butt hinges including carriage of materials in all leads, lifts. Merino make, green century or equivelent.

Extra on above for providing and fixing 1.00mm thick coloured matt finished laminated sheet (sunmica) fixed with adhesive and necessary nails complete in all respect including carriage of materials in all lead and lifts. Merino make, green century or equivelent.

Providing and fixing plain square edged cover fillets (beading) 40mm x 12 mm section with wood screw in ceiling and lining including mitring at junctions 1st class teak wood including carriage of materials in all lead, lifts ad height.

Providing and fixing 40x3 mm flat iron hold fast 40 Cm. long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm 1:3:6 (1cement:3sand:6graded stone aggregate of 20 mm nominal size including carriage of materials in all lead, lift and height.

Providing and fixing anodised aluminum powder coated coloured sliding door bolts with nuts and screws etc. complete including carriage of materials in all leads and lifts Pargon/Flora make or equivalent as approved by Engineer-in-Charge. 250x16 mm.

Providing and fixing anodised aluminum powder coated coloured tower bolts with nuts and screws etc. complete including carriage of materials in all leads and lifts Pargon/Flora make or equivalent as approved by Engineer-in-Charge. 250x10 mm.

Providing and fixing anodised aluminum powder coated coloured handles with nuts and screws etc. complete including carriage of materials in all leads and lifts Pargon/Flora make or equivalent as approved by Engineer-in-Charge.125mm.

Providing and fixing bright finished brass 100mm ACME/ Godrej mortice latch with pair of levers and handles with necessary screws etc. Indian make of approved quality including carriage of materials in all lead and lift.

Providing and fixing bright finish hard drawn hook and eyes, 300 mm size (I.S.I. make) Heavy duty including carriage of materials.

Providing and fixing oxidised MS single action spring hinges bright finished with screws complete isi mark heavy duty as per approved by the Engineer In Charge including carriage of materials in all lead and lift.125mm

Providing and fixing aluminum powder coated hanging door stopper heavy duty ISI as per approved by the Engineer-In Charge including carriage of materials in all lead and lift.

Providing and fixing anodised powder coated aluminium work door window, verntilators and partitions with extruded built up standred tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868. (Minimum anodic coating of grade AC 15) fixed with rewplugs and screws or with fixing clips, necessary filling up of gaps at junctions at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically where ever required including cleast angle, aluminum, snap beading for glazinge/panelling C.P. brass/stainless steel screws. All complete as per architecture drawings and the directions of Engineer In Charges. For door windows and ventilatiors and glazed partitions frames including carriage of materials in all lead and lift.

Powder coated aluminium for shutters of doors, windows and ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings whenever required including the PVC/neoprene gasket required (fittings shall be paid for seperately including carriage of materials in all lead and lift.

Providing and fixing in aluminium door, window, ventilator shutters etc with PVC/neoprene gasket etc complete as per the architecture drawings and the directions of Engineer In Charge as per the architecture drawings and the directions of Engineer-In-Charge (cost of aluminium beading shall be paid in basic item) including carriage of materials in all lead and lift with flaot glass panes of 5.5mm thickness

Providing and fixing double glazed hermetically sealed glazing in aluminium windows, ventilators and partions etc with 6 mm thick clear float double layer toughened insulated glass both side having 12mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (Both priming and secondary sealant) etc as per specificationds, drawings and direction of Engineer-In-Charge complete including carriage of materials in all lead and lift.

Filling the gap in between aluminium frame & adjacent RCC/Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-In-Charge complete. Upto 5mm depth and 5 mm width.

Providing wood work in trusses, purlins, refters, posts, post plates, wall plates and the like wrought framed, hoisted and fixed in positon including carriage of materials in all lead and lift. Sal wood.

Providing and fixing Calcium Silicate (Fine fissured M/Look Aluminium powder coated Silhouetrte Grid sections, with GI hanging bytterfly clips etc Complete False Ceiling of size 600x600 at all levels from FFLas showan in the drg. Rtae shall be inclusive of providing the total system along with installtion etc. As per directions Engineer-In-Charge including carriage of materials in all lead and lift.

Cement concrete flooring 1:2:4 (1cement: 2sand: 4graded stone aggregate 20 mm nominal size) laid in one layer finished with a floating coat of neat cement, 40 mm thick including carriage of materials in all leads and lifts.

Extra for providng and fixing glass strips in joints of terrazzo floor 40mm wide and 4 mm thick including carriage of materials in all lead and lift.

Cement plaster skirting (upto 30 cm height) with cement mortar 1:3 (1 cement : 3 Sand) finfished with floating coat of neat cement including carriage of materials in all lead and lift. 15 mm thick

25 mm thick kota stone slab flooring over 20 mm (average) thick base of cement mortar 1:4 (1cemet:4sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with granite polish etc. complete also carriage of materials in all lead, lifts and heights.

25 mm thick kota stone slab in risers of steps, skirting dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1cement:3sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs including rubbing and polishing and carriage of materials in all lead, lifts and heights

Providing and fixing coloured ceramic tiles 10 to 12 mm thickness in flooring of minimum size of 600x600 mm laid on a bed of 12 mm thick cement mortar 1:3 jointing with cement mixed with pigment to match the shade of tiles including carriage of materials in all leads and lifts of Nitco, Rak/ Kajaria (basic rate not less than Rs.70/- Per Sq.ft.).

Providing and fixing coloured/ printed ceramc tiles of 6 to 8 mm thickness in skirting, risers of steps and dado laid over 12 mm thick cement mortar 1:3 (1cement:3sand) and jointed with cement slurry including carriage of materials in all lead and lifts and heights, Nitco/ Kajaria/ Rak of minimum size 600x300 mm (basic rate not less than Rs.55/- per Sqft.

Providing and fixing coloured ceramic tiles 10 to 12 mm thickness in flooring of minimum size of 300x300 mm laid on a bed of 12 mm thick cement mortar 1:3 jointing with cement mixed with pigment to match the shade of tiles including carriage of materials in all leads and lifts of Nitco, Rak/ Kajaria (basic rate not less than Rs.60/- Per Sq.ft.).

Providing and laying granite stone flooring 20 mm average thickness over a base of 20 mm thick cement mortar 1:3 (1cement:3sand) laid over and jointed with grey cement slurry mixed with pigment to match shade of the granite stone including rubbing and polishing with granite polish finish grey/red including carriage of materials in all lead, lifts and heights..(basic rate not less than Rs.260/- per Sft).

Providing and laying garsa stone 12 mm clading on RCC surface side as on faces of arch masonary wall etc on 12mm thick cement plaster 1:3 (1cement:3sand) and jointed with cement slurry including scaffolding etc comlete including carriage of materials in all lead, lifts and heights..

Providing and laying heavy duty precast cement concrete inter locking paver blocks vibro compacted upto M-30 grade including border of curv block gray or colour over sub base of concrete with 25 mm thick average thickness of cement morter 1:4 (I cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of block including curring rubbing and polishing complete (sub base concrete floor to be paid for seprataly) including carriage of materials in all lead, lifts. NTC make 40mm thick.

NTC make 60mm thick

Providing edge mording in marble/graynite stone/Kota stone including carriage of materials in all lead, lifts

Providing and fixing 0.60 mm thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coated including fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia metre with prepainted limpet and rubber washers complete with all accessories as required as per the direction of Engineer-in-Charges. (Tata/Century wells make) including carriage of materials in all lead, lift and height.

Providing and fixing ridges or hips 60 cm overall with 0.60 mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts & nuts 6 mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charges including carriage of materials in all lead, lift and height (Tata/Century wells make).

Providing and fixing valley 60 cm overall 0.60 mm thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials in all lead, lift and height (Tata/Century wells make).

Providing and fixing flashing 38 cm overall with 0.60 mm thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia meter & prepainted G.I. limpet & bitumen washer completed with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials in all lead, lift and height (Tata/Century wells make).

Providing and fixing 0.60 mm prepainted sheet gutter 15 cm wide 45 cm over all forming box with nut and bolts and washers etc. including making necessary connection and all lead, lifts and carriage of materials. (Tata/Century wells make).

Providing and fixing on wall face PVC finolex rain water pipes including fitting the joints with adhesive and cement mortar 1:2 (1cement:2sand) 100 mm dia pipe including carriage of materials in all lead and lifts.

Providing and fixing wall face PVC finolex rain water pipes including filling the joints with spun yard soaked in neat cement slurry and cement mortar 1:2 (1cement : 2 sand) including carriage of materials in all lead and lifts. PVC plain bend 110mm

PVC plain shoe 110mm

Providing and fixing 2 mm thick B.P. sheet in facia etc. welded with M.S. steel frame (M.S. steel frame to be measured and paid for separately) including cutting and applying a coat of red lead primer and carriage of materials in all leads, lifts and heights.

Steel work welded in built up section, trusses and framed work, including cutting, hoisting, fixing in position and applying a coat of red lead paint including carriage of materials in all lead lifts and height. In strusses and trussed purline in building.

In gratings framed guard bars ladders, railings brackets and similar works

Steel works using MS hollow sections IS code 4923 welded and including machine bending as required shape built up sections trusses framed & railing etc including cutting hoisting, fixing in position and applying a priming coat of red lead paint, including carriage of materials in all lead lifts and height. under polycarbonate sheets roofing.

Providing and fixing stainless steel(Grade- 304) railing Gates etc made of hollow tubes, channels, plates etc. including welding. Grinding. buffing, polishing and making curvature wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, ie. fixing the railing Gates with necessary accessories&stainless steel dash fasteners, stainless steel bolts Nuts fasteners etc, of required size, on the top of the floor or the side of waist slab with suitable arrangement as per the approval of Engineer-incharge, including carriage of materials in all leads and lifts

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil.grease,dirt and other foreign matter) sand papering and knotting including carriage of materials in all leads and lifts

Painting two coats (excluding priming coat)on new wood and wood based surfaces with ready mixed paint, brushing to give an even shade including cleaning of all dirt,dust and other foreign matter sand papering and stopping including carriage of materials in all leads and lifts

Applying priming coat over new steel and other metal surfaces after and including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wood scraper and sand paper complete. Including carriage of materials in all leads, lifts and heights, in With ready mixed priming paint brushing red lead, red, oxide/zing oxide chrome including carriage of materials in all lead and lifts and heights.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint to give an even shade including cleaning the surface of all dirt, dust and other foreign matter including carriage of materials in all leads, lifts and heights White/other than white enamel paint.

Applying priming coat on new concrete/masonry/ asbestos cement plastered surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required with ready mix premier including carriage of materials in all leads, lifts and heights.

6 mm thick cement plaster to ceiling in cement mortar 13 (1 cement 3 sand) including carriage of materials in all leads and lifts and heights

15mm cement plaster in single coat on rough side of brick/concrete/stone wall for interior plastering in all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 16 (1 cement Sand) including carriage of materials in all leads and line and heights

Applying putty (Birta/JK) on undecorated wall including preparing the surface by thoroughly cleaning grease, dirt dust and other foreign matter including carriage of materials in all leads and liftsand heights

20 mm thick cement plaster In two coats backing coat of 15mm and finishing coat 5 mm thick on rough side of brick/stone masonry wall for interior plastering upto floor two level including arrises internal rounded angles chamfers and or rounded angles notexceeding 80 mm in girth and finished even and smooth in cement mortar 16 (1 cement sand) including carriage of materials in all leads and lifts

Providing and filling cinder in the sunken portion of toilets to the required level of toilet including watering ramming and carriage ofmaterial in all leads and lifts.

Wall Painting ( two coats) with plastic emulsion paint of approved brand and manufacture on decorated wall surface to give an even shade including thoroughly brushing the surface clean of all dirt grease loose pieces of scale and sand paper smooth including applying of putty a required for making the surface including carriage of materials in all lead and lifts

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand paper smooth and carriage of materials inall lead and lifts and heights

Finishing wall with water proofing Apex Exterior paint manufacture and of required shade on undecorated wall surfaces (one coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials including carriage of materials in all leads, lifts and height

Constructing course rubble hammer dressed U shape open surface drain with side wall 15x22 cm in cement mortar 1:6 (1 cement 6 sand) and inside plastering with cement plaster 1:3(1 cement: 3 sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 cement :5 sand: 10 graded stone aggregate) of 40 mm nominal size and 7.5 cm cement concrete 1:2:4 (1 cement 2 and:3 graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design including carriage of materials in all leads and lifts

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement:3 sand:6 graded stone) including carriage of materials in all lead and lifts

Providing under layer for plinth protection of 75 mm thick consolidated (bed dry brick/stone aggregate 40 mm nominal) well rammed and solidated and grouted with fine sane including preparation of ground including carriage of materials in all lead and lifts

Providing and fixing vitreous china water closet one piece EWCS with sheet cover and twine flush fitting ceramake Cat No. S1013101s or equivelent undwere/Jaguar make including carriage of materials in all lead and lifts

Providing and fixing vitreous china water closet one piece EWCS with sheet cover and twine flush fitting ceramake Cat No. S1020102, S1060101, B1510101, B1810101 or equivelent Hundwere/Jaguar make including carriage of materials in all lead and lifts

Providing and fixing Vitreous China water closet squatting pan (earth work, bed concrete and trap to be measured and paid for separately) including carriage of materials in all lead and lifts. Orrissa pan Ceramake Cat No. S1050109, B1510101, B1520102 or equivelent Hundwere/Jaguar make including carriage of materials in all lead and lifts

Providing and fixing vitreous china wash basin with single hole for pillar tap including carriage of materials in all lead and lifts Ceramake Cat No. S2030113 or equivelent Hundwere/Jaguar make including carriage of materials in all lead and lifts

Providing and fixing vitreous china wash basin with pedestal including cutting hole and making good the same including carriage of materials in all lead and lifts Ceramake Cat No. S2040109, S2090101, or equivelent Hundwere/Jaguar make including carriage of materials in all lead and lifts

Providing and fixing vitreous china Urinal Ceramake Cat No. S4020102 or equivelent Hundwere/Jaguar make including carriage of materials in all lead and lifts

Providing and fixing vitreous china division plate for urinal ceramake Cat No. S1019101 or equivelent Hundwere/Jaguar make including carriage of materials in all lead and lifts

Providing and fixing stainless steel sink with drain board ceramake make Cat No. B4622101 or equivelent Hundwere/Jaguar make including carriage of materials in all lead and lifts

Providing and fixing C.P. bib tap with wall flange 15 mm dia capastan head (Long body) Jal make cat No.17362 or equivelent Cera/Jaguar make including carriage of materials in all lead and lifts

Providing and fixing C.P. bib tap 15mm Jal make Cat No. 17360 or equivelent Cera/Jaguar make including carriage of materials in all lead and lifts

Providing and fixing angle valve Jal make Cat No. 17480 or equivelent Cera/Jaguar make including carriage of materials in all lead and lifts

Providing and fixing C.P. connection pipe with brass union wash basin sink 15mm nominal dia including carriage of materials in all lead and lifts

Providing & fixing of C. P. Towel Rail complete fixed to wooden plugs with CP brass screws and washer Jal make Cat No 26522 or equivelent Cera/Jaguar make including carriage of materials in all lead and lifts.

Providing & fixing C.P. grating 100mm dia Chilly make nominal size complete including carriage of materials in all leads & lifts

Providing & fixing C.P. Paper holder Jal make Cat No. 22546 or equivelent Cera/Jaguar make including carriage of materials in all lead and lifts

Providing & Fixing C.P health faucet Jal make Cat No. 488 or equivelent Cera/Jaguar make including carriage of materials in all lead and lifts

Providing & fixing C.P. Towel ring Jal make Cat No 36524 or equivelent Cera/Jaguar make including carriage of materials in all lead and lifts

Providing & Fixing C.P. Soap tray Jal make Cat No. 36540 or equivelent Cera/Jaguar make including carriage of materials in all lead and lifts

Providing & fixing C.P. Robe Hook Jal make Cat No: 22560 or equivelent Cera/Jaguar make including carriage of materials in all lead and lifts

Providing and fixing 1200 mm x 900 (Ornamental type) superior glass, 4 mm with C.P. brass screws and washers including carriage of materials in all lead and lifts. (Modi or sant gobian make with ornamental sal wood frame)..

Providing & fixing C.P. wall mixer set with over head shawer with elvow coupling Jal make CAT No. 17770 or equivelent Cera/Jaguar make including carriage of materials in all lead and lifts.

Providing & fixing C.P. basin Mixer Jal make CAT No.17618 or equivelent Cera/Jaguar make including carriage of materials in all lead and lifts.

Providing & fixing C.P. sink mixer of Jal make CAT No. 17634 or equivelent Cera/Jaguar make including carriage of materials in all lead and lifts

Providing & fixing CP Pillar Tap, complete JALmake cat no 17220 or equivelent Cera/Jaguar make including carriage of materials in all lead and lifts

Providing & Fixing CP bottle trap 32mm dia for wash basin JAL make Cat No. 1861 or equivelent Cera/Jaguar make including carriage of materials in all lead and lifts

Providing and fixing C.P. waste 32mm dia including carriage of materials in all lead and lifts

Providing and fixing PVC pipe Finolex ventilating pipes jointed with standard quality adhesive including carriage of materials in all lead and lifts110 mm dia.

75 mm dia

Providing and fixing PVC finolex fittings and accessories of standard/ approved quality including carriage of materials in all lead and lifts. Door bend 75mm nominal size

b)110mm nominal size

Plain bends 75mm nominal size

b) 110mm nominal size

TEE 75mm dia

b) 110mm dia

Collar 75mm dia

b) 110mm dia

Clamps 110mm dia

Cowal 110mm dia

Providing & Fixing PVC finolex floor trap of self cleansing design complete including cost of cutting & making good the walls & floors Including carriage in all lead and lifts. 75mm nominal size

Providing and laying cement concrete 1:2:4 mix (1 cement: 2 coarse sand : 4 stone osl aggregate 20mm and down gauge) 75mm in bed and around UPVC Pipes (soil and waste pipe). 110mm dia pipes under floor including centering and shuttering wherever required. 110mm dia

b) 75mm dia

Providing & Fixing PVC clean out plug with suitable insert keys for opening in: brass cap 2.06 male threaded joint with threaded PVC socket fixed to UPVC pipe joints as required complete in all respects Including carriage in all lead and lifts. 110 mm dia.

Providing and fixing UPVC rain water pipes of 6kg/cm conforming to IS: 4985 including all fittings with or without access I.e bends, Junctions, cowls, offsets, etc, and jointing with solvent cement including cutting holes in walls and floors, wherever required and making good the same, complete as directed by the Engineer-in-Charge Including carriage in all lead and lifts. 110mm outer dia.

Providing and fixing materials for making rain water khurra of size 450x450mm as specified including 3 mm thick lead flushing from pipe edges with single piece of lead sheet of size 300-150mm set in layer of cold bitumen including Cl. grating 5mm thick circular or square. For 110mm dia outlet with vertical grating Including carriage in all lead and lifts.

Providing and fixing Cl Hooper With Dome. For 110mm dia outlet including setting in floor with cement mortar to match with floor finish complete in all respect Including carriage in all lead and lifts.

Providing & fixing to wall ceiling and floor galvanised mild steel tube (heavy grade) tube fittings and clamps including making good the wall ceiling and floor Including carriage in all lead and lifts.15mm dia

b) 20mm dia

c) 25mm dia

d) 32mm dia

Providing & Fixing brass full way valve with wheel including carriage of materials in all leads and lifts. Jalato/Sant make 15mm nominal bore

b) 20mm nominal bore

Providing and fixing brass ball valve with setting and gland of superior quality having minimum working pressure of 10 kg/cm Jalato/Sant make Including carriage in all lead and lifts.b) 20mm dia

Providing brick pedestal using sand lime bricks of class 75 in pillars with square base (size 9"x9"x9") including joints finish flush/ranked to 12 mm depth, cured etc. in cement mortar 1:4 (1 cement: 4 sand) and finished with 15mm cement plaster using cement mortar 1:4 (1 cement: 4 fine sand), complete in all respect including carriage in all lead and lifts. (For pipe support at terrace)

Providing and fixing C.I. double acting air valve of approved quality with bolts,nuts,rubber insertion, tail pieces, tapers etc. If required as complete. 20 mm dia Including carriage in all lead and lifts.

Providing and fixing gate valve Jalato/sant make 20mm dia Including carriage in all lead and lifts.

Excavating trenches all kind of soil of required with for pipes, cables etc including excavation for socket and dressing of sides ramming of bottoms depth upto 1.50 m including timbering shuttering centering etc. as required getting out the excavated soil and then returning the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering etc. and disposal of surplus excavated soil outside Pipes cables etc exceeding 80 mm dia but not exceeding 300 mm dia.

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement: 1 fine sand) including testing of joints etc. complete Including carriage in all lead and lifts.150 mm dia

Providing and laying cement concrete 1:5:10 ( 1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) allround SW pipes including in bed concrete as per standard design Including carriage in all lead and lifts. 150 mm dia

Construction manhole with R.C.C. top slab in 1:2:4 Cement: 2 sand : 4 paved stone Aggregate 20 mm nominal size) foundation concrete 1:4:8 (1 cement:4 sand:graded stone aggregate 40 mm nominal size) inside plastering 15 mm thick with cement mortar 13 (cement:sand) finished with a floating coat of neat cement slurry and making channel in cement concrete 1:2:4 (cement:2 sand: 4 graded stone aggregate 20 mm nominal size) finished smooth complete including curing and testing including carriage of materials in all lead and lift. a) Inside size 800mmx 800mm x 500 mm deep including CI cover with frame light duty single seat pattern) 455 mm x 610 mm internal dimension total weight of cover and frame to be not less than 38 Kg (weight of cover 23 kg and weight of frame 15 Kg ) With 200 mm thick wall of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement: 3 sand).

b) Inside size 800 mm x 800 mm x 1000 mm deep including C.I. cover with frame light duty single seat pattern) 450 mm x 610 mm internal dimension total weight of cover and frame to be not less than 38 Kg (weight of cover 23 kg and weight of frame 15 kg:00) With 200 mm thick wall of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement and 3 sand)

c) Inside size 1200 mm x 900mm x 1500 mm deep including CI. cover with frame medium duty single 500 mm Internal dimension total weight of cover and frame to be not less than 116 Kg (weight of cover 58 Kg and weight of frame 58 kg (0) With 300 mm thick wall of brick masonry using common burnt clay building bricks in cement mortar 1:3 Cement and brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 Cement and 3sand).

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per 15:10910 on 12 mm dia steel bar conforming to IS 1786 having minimum cross section as 23 mm x 25 mm and overall minimum length 263 mm and width as 165 mm with space between protruded legs having 2 mm tread on top surface by ribbing on chequering besides necessary and adequate anchoring projections on tall length on 133 mm as per standard drawing and suitable to withstand the bend test and chemical resistance test as per specifications and having manufacturer's permanent identification mark to be visible even after fixing including fixing in manholes with 30x20x45 cm cement concrete block 1:12:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) complete as per desien Including carriage in all lead and lifts.

Providing and laying non pressure NP2 class (heavy duty) R.C.C. Pipes S&S jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc. complete including carriage of materials all lead and lifts.. 150mm dia

Providing and laying cement concrete 1:4:8 (1 cement :4 coarse sand : 8 graded stone aggregate 40 mm nominal size) alround SW/ RCC pipes including bed concrete as per standard design including carriage of materials all lead and lifts. 150mm dia

Constructing brick masonry road gully chamber 450 x 450 mm with bricks of class designation 75 in cement mortar 1:5 (1 cement: 5 coarse sand), And cement plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse-sand) finished with a floating coat of neat cement, outside plaster 12 mm thick in cement mortar 1:3(1 cement: 3 coarse sandy 10 cm thick foundation concrete 1:4:8 mix (1 cement 4 coarse sand : 80 graded stone aggregate 40mm nominal size) including 500x450 mm RCC horizontal grating wilh frame fixed in 15 cm thick cement concrete 1:2:4 (1 cement:2 coarse sand : 4 grade stone aggregate 20 mm nominal size) Including excavation, refilling and disposal of surplus earth as directed by Project Manager as per standard design including carriage of materials all lead and lifts. 450 x 450 mm to 750mm depth

Construction of grease trap with class 75 designation bricks in cement mortar 1:5 complete with cement concrete baffle wall, foundation concrete (1:4:8) RCC top slab (precast) with 1:2:4 concrete complete with inside plastering 12mm thick cement mortar 1:3 and finished with a floating coat of neat cement etcincluding carriage of materials all lead and lifts. Size 1650 x 750 x 750 mm deep

Providing & fixing PVC water storage tanks syntax or equivalent including fitting cost of connecting/tank nipples, make connections etc including carriage of materials all lead and lifts.

Supplying C.I. cover heavy duty rectangular 455X610mm from weight 38 kg (Single seat) including carriage of materials all lead and lifts.

Providing and filling pit gravel od size 3mm to 6mm in the desilting chamber including carriage of materials all lead and lifts.

wiring for light point / fan point/ exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low amoke single core (flexible ) copper conductor cable in surface /recessed PVC conduit with modular switch ,modular plates,suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required including carriage of material in all leads & lifts. Switches & wires should be Havell's/Plaza/Greatwhite/Legrand/Anchor Panasonic/L&T and PVC pipe Diplast/Polyplast make or as approved by the Engineer-in-Charge a) Group A.

b) Group C.

Wiring for twin control light point with 1.5 Sq mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface /recessed PVC conduit , with 2-way , 5/6 amps piano type switch and earthing the light point with 1.5 Sq. mm. HRFRLS/PVC insulated single core copper conductor cable as required including carriage of material in all leads & lifts. Switches & wires should be Havell's/Plaza/Greatwhite/Legrand/Anchor Panasonic/L&T and PVC pipe Diplast/Polyplast make or as approved by the Engineer-in-Charge. a) Group C.

wiring for circuit /sub- main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible)copper conductor cable in surface/ recessed PVC conduit along with 1 No . HRFRLS/ PVC insulated single core copper conductor cable of same size for earthing as required including carriage of material in all leads & lifts. Havell's/Plaza//L& T/Anchor Panasonic and PVC pipe Diplast/Polyplast make or as approved by the Engineer-in-Charge. a) 2x1.5 Sq.mm

b) 2x2.5 Sq.mm

c) 2x4.0 Sq.mm

d) 2x6.0 Sq.mm

e) 2x10Sq.mm

wiring for circuit /sub- main with 4x10 Sq.mm . PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible)copper conductor cable in surface/ recessed PVC conduit along with 2 No .10 Sq.mm (4x10+2x10) HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required including carriage of material in all leads & lifts. Switches & wires should be Havell's/Plaza/Greatwhite/Havell's/L& T/Anchor Panasonic a and PVC pipe Diplast/Polyplast make or as approved by the Engineer-in-Charge.

wiring for circuit /sub- main with 4x16 Sq.mm . PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible)copper conductor cable in surface/ recessed PVC conduit along with 2 No .16 Sq.mm (4x16+2x16) HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required including carriage of material in all leads & lifts. Switches & wires should be Havell's/Plaza/Greatwhite//L& T/Anchor Panasonic a and PVC pipe Diplast/Polyplast make or as approved by the Engineer-in-Charge.

Supplying and fixing following rating Modular switch /socket in the existing switch box /cover plate including connections etc. as required including carriage of material in all leads & lifts Havell's/Plaza/Greatwhite/Legrand/ Anchor Panasonic/L&T make or as approved by the Engineer-in-Charge. a) Telephone socket outlet, Modular.

b) T.V Socket outlet, modular.

Supplying and fixingDing - dong / Electronic musical bell suitable AC / DC, Single Phase 230 volts complete as required including carriage of material in all leads & lifts Havell's/Greatwhite/Legrand/ Anchor Panasonic/L&T make or as approved by the Engineer-in-Charge.

Supplying & Fixing of G.I modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required including carriage of material in all leads & lifts Havell's/Greatwhite/Legrand/ Anchor Panasonic/L&T make or as approved by the Engineer-in-Charge. 2 Modules ( 78 mm x 78 mm x 50 mm)

Supplying & fixing Modular blanking plate on the existing modular metal bix as required including carriage of material in all leads & lifts Havell's/ Greatwhite/Legrand/ Anchor Panasonic/L&T make or as approved by the Engineer-in-Charge.:-

Supplying and fixing stepped type Modular fan regulator on the existing modular box including making connections etc. as required including carriage of material in all leads & lifts Havell's/Greatwhite/Legrand/ Anchor Panasonic/L&T make or as approved by the Engineer-in-Charge.

Supplying and fixing G.I Modular box of (140mmx78mmx50mm) size with modular plate and cover in rcess including providing and fixing 5 pin 5/6 amps modular socket outlet and 5/6 amps, modular switch, connections etc. as required including carriage of material in all leads & lifts Havell's/Greatwhite/Legrand/ Anchor Panasonic/L&T make or as approved by the Engineer-in-Charge.

Supplying and flixing G.I Modular box of (140x78mmx50mm) size with modular plate and plate cover in recess including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps, modular switch, connections etc. as required including carriage of material in all leads & lifts Havell's/Greatwhite/Legrand/ Anchor Panasonic/L&T make or as approved by the Engineer-in-Charge.

Supplying and flixing ceiling rose on the existing junction box / wooden block including connections. etc. as required including carriage of material in all leads & lifts Havell's/Greatwhite/Legrand/ Anchor Panasonic/L&T make or as approved by the Engineer-in-Charge.

Extra for fixing the louvers / shutters complete with frame for exhaust fans of all sizes as required including carriage of material in all leads & lifts.

Providing & Installation of stationary storage type Electric water heater (Geyser) of various of sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, proving and fixing of Non-return valve, Dead weight safety valve, 2 No. C.P connection rods 18" long, making good the damages, electrical connections, safety valve connections, testing and commissioning ets. as required including carriage of material in all leads & lifts Havell's/Racold/Spherehot/Jaguar/Jal make or as approved by the Engineer-in-Charge. a) 35 ltr. Capacity category B

Supply , fixing ,installation & commissioning of lighting fixtures as per the details given below including necessary hardware such as clamps,nuts, bolts, nails, screws and suspension chains as required for fixing the fixtures in position including carriage of material in all leads & lifts Havell's/ Greatwhite/Anchor Panasonic/L&T/Philips/Syska/Bajaj make or as approved by the Engineer-in-Charge. Surface/Recess type down light 12W LED

Surface/Recess type down light with 9/10 W LED lamp.

Surface mounted tube light with 40W LED lamp.

Decorative type wall bracket with 9/12W with LED lamp.

Surface type bulk head light with 10W LED lamp.

Mirror Light LED 9/12 Watts.

Supplying and fixing of following way, single pole and neutral sheet MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wire- set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and power painted, including earthing etc. as required including carriage of material in all leads & lifts Havell's/Greatwhite/Legrand/ Anchor Panasonic/L&T make or as approved by the Engineer-in-Charge. a) Double door-8 way

b) Double door-12 way

Supplying and fixing of following way triple pole and neutral, sheet steel MCB distribution board, 415 volts, on surface / recess, with provision for 4-pole MCB/Insolator / RCCB / RCBO as incomer and SP MCB's as outgoing, complete with tinned copper bus- bar, wire-set, neutral link, each bar, din-bar, detachable gland plate, cable, identification labels interconnections, phosphatized and power painted, including earthing etc. as required including carriage of material in all leads & lifts Havell's/ Greatwhite/Legrand/ Anchor Panasonic/L&T make or as approved by the Engineer-in-Charge. Double door-4way(8+12),horizontal type

Double door-8 way (8+24),horizontal type

Double door-12 way (8+36), horizontal type

Supplying and erection of 6 amps. To 32 amps. Rating, 10 KA breakiung capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required including carriage of material in all leads & lifts Havell's/Greatwhite/Legrand/ Anchor Panasonic/L&T make or as approved by the Engineer-in-Charge. Single pole. Cat-A

Supplying and fixing following rating, double pole( single phase & neutral) 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required including carriage of material in all leads & lifts Havell's/Greatwhite/Legrand/ Anchor Panasonic/L&T make or as approved by the Engineer-in-Charge.. 40 Amps. Cat-A

Supplying and fixing following rating, four pole (three phase & netural) 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required including carriage of material in all leads & lifts Havell's/Greatwhite/Legrand/ Anchor Panasonic/L&T make or as approved by the Engineer-in-Charge.. ) 63 Amps Cat-A

Earthing with G.I earth pipe 4.5 mtr. Long and 40mm dia, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required including carriage of material in all leads & lifts.

Extra for using salt and cock for G.I or copper Pipe erth electrode complete as required including carriage of material in all leads & lifts.

Extra for using salt and coke for pipe earth electrode complete as required including carriage of material in all leads & lifts.

Supplying and laying 25mmx6mm G.I. strip at 0.05 mtr. Below ground level for earth electrode conductor, including soldring etc. as required including carriage of material in all leads & lifts.

Supplying and laying 6 swg gi wire at 0.50 mtr below ground level for earth electrode conductor, including soldering etc. as required including carriage of material in all leads & lifts

Providing and fixing 8 SWG (4 mm dia.) copper wire on surface or in recess for loop earthing along with existing surface/recessed conduit/sub-main wiring/cable as required including carriage of material in all leads & lifts.

Providing and fixing of lightning conductor finial final, made of 25 mm dia. 300 mm long copper tube, having single prong at top, with 85 mm dia 3 mm thick copper base plate including holes etc. complete as required including carriage of material in all leads & lifts.

Riveting, sweating and soldering of copper.G.I tape ( with another copper/ G.I tape base of the finial or any other metallic object) as required including carriage of material in all leads & lifts.

Supplying and fixing copper tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required (for vertical run) including carriage of material in all leads & lifts

Supplying and fixing copper tape 20mmx3mm thick on parapet or surface of wall for lightning conductor as required (for horizontal run) including carriage of material in all leads & lifts

Supplying and fixing G.I tape 20mmx3mm thick on parapet or surface of wall for lighting conductor as required (for required (for vertical run) including carriage of material in all leads & lifts

Supplying and laying copper tape 32mmx6mm thick from earth electrode directly in grounf as required including carriage of material in all leads & lifts.

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm ) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required including carriage of material in all leads & lifts Havell's/Bajaj/Usha/Khaitan make or as approved by the Engineer-in-Charge a) Ceiling Fan 1200mm sweep, Cattegory-A

b) Ceiling Fan 1400mm sweep, Cattegory-A

Providing and installation of xhaust fan of following sizes in the existing opening, including making the hold to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required including carriage of material in all leads & lifts Havell's/Bajaj/Usha/Khaitan make or as approved by the Engineer-in-Charge. a) Exhaust Fan. Light duty, (Domestic) 225 mm sweep

b) Exhaust Fan. Light duty, (Domestic) 300 mm sweep

Supplying and fixing of following sizes of PVC conduit along with accessories in surface/recess including or cutting the wall and making good the same in case of recessed conduit as required including carriage of material in all leads & liftsDiplast/Polyplast/Polyfit make or as approved by the Engineer-in-Charge.. (Conduiting for TV,Telephone, misc & For external cables. a) 20mm dia

b) 25mm dia

c) 32mm dia

d) 40mm dia

e) 50mm dia

Supplying & drawing of following pair of Fire retardent, PVC insulated 0.5 sqmm (FR-Flexible, cooper conductor, Flat , Unarms, Telephone cable in Existing Surface / recessed, Steel / PVC Conduit as required including carriage of material in all leads & lifts. Havell's/Plaza/Greatwhite/L&T/ L& T/Anchor Panasonic make or as approved by the Engineer-in-Charge.. a) 1 Pair

b) 2 Pair

c) 4 Pair

Supplying & drawing Co-axial TV Cable, RG-6, Grade , 0.7 mm, 75 ohms (Copper conductor, PE insulated, Shielded with fine tinned copper Braid & Protected with PVC Sheath in The existing surface / recessed, steel / PVC conduit as required including carriage of material in all leads & lifts. Havell's/Plaza/Greatwhite/L&T/ L& T/Anchor Panasonic make or as approved by the Engineer-in-Charge..

10 Pair MDF with crone Module for termination of workstation side voice Cable (Krone make) including carriage of material in all leads & lifts.

Supplying & drawing LAN Cable,Cat-5E,Solid copper conductor protected with PVC sheath in the existing surface / recessed, Steel / PVC Conduit as required including carriage of material in all leads & lifts. Havell's/Plaza/Greatwhite/L&T/ L& T/Anchor Panasonic make or as approved by the Engineer-in-Charge..

Earthing with G.I. earth earth pipe 4.5 mtr long and 40 mm dia, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required including carriage of material in all leads & lifts .

Extra for using salt and cock for G.I or copper Pipe erth electrode complete as required including carriage of material in all leads & lifts ..

Supplying and laying 25mmx6mm G.I. strip at 0.05 mtr. Below ground level for earth electrode conductor, including soldring etc. as required including carriage of material in all leads & lifts ..

Supplying and laying 6 swg gi wire at 0.50 mtr below ground level for earth electrode conductor, including soldering etc. as required including carriage of material in all leads & lifts

Providing and fixing 8 SWG (4 mm dia.) copper wire on surface or in recess for loop earthing along with existing surface/recessed conduit/sub-main wiring/cable as required including carriage of material in all leads & lifts ..

Supplying and erection of Galvanized Iron (G.I.) pipe pole 'A' quality of suitable length and dia., 4.47 mm thickness, including fixing up to a given depth below G/L. The hole of excavation about 30 cm dia. and given depth to be filled in up to 15 cm below G/L with 1:3:6 cement concrete and there above plinth with 1:2:4 cement concrete up to a height of 45 cm from G/L. The radial thickness of the plinth above G/L should not be less than 6.35 cm and sufficient to completely flush a 180 mmx100 mmx 45 mm deep, glass filled Nylan F.R. grade box for housing a 16 Amp. MCB, the outer surface of the plinth to be finished with 1:3 cement plaster 6 mm thick, the fuse-box shall have a water tight cover, including painting of pole with two coats of approved color, brand and manufacture of paint over a priming coat complete in all respects as required including carriage of material in all leads & lifts Jindal/Tata make .:- 4 Meter long having nominal bore dia. 65 mm planting deph 80 cm with depth 95 cm.

Supplying and fixing of new generation, Post Top, energy saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape luminaire with high power LED's as light source Havell's make Ruby Clear Cat No. LHEVBGP7PN6K025 complete with all accessories including making connections, testing etc. as required including carriage of material in all leads & lifts Havell's/Syska/ Greatwhite/Bajaj/Philips make or its equivalent as approved by the Engineer-in-Charge

Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade direct in ground; to be laid 1 meter below the ground level including excavation and refilling the trench etc. of the required size Havell's/Plaza/polycab/Phenolix/KEI make or as approved by the Engineer-in-Charge..:- a) Armoured Cable 6 Sq. mm (Twin Core)

Providing, laying and fixing of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade on surface etc. of the required size Havell's/Plaza/polycab/Phenolix/KEI make or as approved by the Engineer-in-Charge. a) Armoured Cable 6 Sq. mm (Twin Core)

FIRE ALARM SYSTEM. Fire Alarm panel Microprocessor based 4Loop expandable to 4loop analoque conventional Fire Alarm Main Panel with Touch Screen Display / 2x40 character LCD display . The loop capacity shall be to take min 20 analogue conventional detector/devices, with battery & battery charger . 240 V AC power supply , automatic battery charger , 24 volts sealed lead acid batteries sufficient for 24 hours normal working and in case of emergence /power failure then the system shall be capable of operation for 2 hours in standby mode & 5 minutes in case of alarm condition including carrige of material in all leads & lifts. Appolo/ Honeywell make or as approved by the Engineer-in-Charge.

Supply, installation, Testing & Commisioning of conventional Smoke detector with base and complete in all respect including carrige of material in all leads & lifts. Appolo/ Honeywell make or as approved by the Engineer-in-Charge.

Supply, installation, Testing & Commisioning of conventional heat detector with base and complete in all respect including carrige of material in all leads & lifts. Appolo/ Honeywell make or as approved by the Engineer-in-Charge.

conventional Manual Call Point (Pull down/ Break Glass Type). The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. UL Listed & FM Approved including carrige of material in all leads & lifts. Appolo/ Honeywell make or as approved by the Engineer-in-Charge.

conventional Sounder cum Strobe (Hooter) rated at 75 dBA @ 3m for Audible annunciation and 75cd flashintg at 1 Hz for visual indication.UL Listed & FM Approved including carrige of material in all leads & lifts. .

Supply, installation, Testing & Commisioning of Response indicator for all detectors located above false ceiling and in closed cabins including carrige of material in all leads & lifts. Appolo/ Honeywell make or as approved by the Engineer-in-Charge.

Exit Signage. Emergency Exit Lights as per model Omniex with laser eatched translucent polyacrylic 8mm thick sheet illuminated with the hidden LED strip in Green Colour. The Unit shall be 230 V A.C. & 12 V DC operable & shall be supplied with inbuilt Battery for 2hours backup, Battery charger complete with hanging/ Mounting arrangements including carrige of material in all leads & lifts. Lifeguard/ Omax make or as approved by the Engineer-in-Charge.

Cables & Conduits. Supply and Fixing of ISI marked 25 mm dia PVC Conduit including carrige of material in all leads & lifts. Diplast/polyplast/polyfit make.

Supply and drawing of 2 C X 1.5 Sq mm multi stranded twisted unshielded FRLS Copper cable including carrige of material in all leads & lifts. Havells/Plaza/Greatwhite/ L&T/Anchor panasonic make.

Vidya Infrastructure and Developers

P K Construction Shimla Pvt Ltd

Kalsi Brothers

HANS CONSTRUCTIONS