PROVN OF WINDOW GRILL FOR TRAINING TEAM OFFICE AND SMC, TOILET/BATHROOM BLOCK NEAR BLDG NO T-40 AND SPECIAL REPAIR TO BLDG NO P-02 (TOILET BLOCK) AND INTERNAL WIRING OF BLDG NO T-48 OF SINGLE LIVING ACCN AT OTA GAYA

Amount

Cuttting holes exc 150 sq cm but not exc 400 sq cm into or through brick walls built in CM or cement lime mortar and stone walls built in lime mortar and making good in PCC 1:2:4 type B1 complete.

Taking down chowkhat or frame exc 1.5 sqm but not exc 4.00 sqm (without taking off shutter) from the frame

Taking down chowkhat or frame n.exc 1.5 sqm (without taking off shutter) and refixing in the same opening complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc

M&L PCC 1:2: 4 type B1 (using 20mm graded stone aggaregate) as in 25 mm thick for levelling of surface.

M & L Brick work with subclass 'B' bricks (except bricks) straight or curved on plan exc 6m mean radius built in CM 1:6.

M & L 10 mm thick Rendering in CM 1:4 on brick work or concrete surfaces of wall and finished surfaces fair and even without using extra cement.

M & L 15 mm thick Rendering in CM 1:4 over fair faces of brick work or concrete surfaces of wall and finished surfaces fair and even without using extra cement with WPC. Note : WPC shall be measured and paid separately.

Supply only water proofing compound (Sika latex power)

M & L Two coats of acrylic distemper on wall surfaces including preparation of newly plastered surfaces over coat of 1 mm thick birla/JK wall putty complete.

S & F Aluminium decorative grills for windows, ventilators aperature 50 mm x 50 mm and weight not less than 2.07 Kg/Sqm including channels and joining cleat for fixing, fixing arrangement, complete.

S & F Stainless steel butt hinges, 125 mm long and welded to angle iron frame work complete

S & F Stainless steel tower bolts 200 mm long complete.

M&L 4 mm thick sheet glass ordinary quality and glazing with oil putty or fixing rubber gasket with aluminium frame n. exc 0.5 sqm in each pane complete.

M & L Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers

S & F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

M&L PCC 1:2:4, type B-1 using 20 mm graded stone aggregate as in coping, benching, bed block, lintel band, drains and channels etc and similar work incl form work complete.

M & L Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M & L Extra over framed work for portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc

M & L Applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces

M & L Non skid ceramic coloured tiles of 7 to 8 mm thick (square/ rectangular) polished, area of each tiles exc 0.11 Sqm but n.exc 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15mm thick in cement mortar 1:4 complete.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/dense soil

Excavation in trenches n.exc 1.5m deep & n.exc 1.5m wide on plan in hard/dense soil and getting out complete all as spd and directed by EIC

Excavation in trenches exc 1.5m & n.exc 3.00 mtr in deep and n.exc 1.5m wide on plan in hard/dense soil and getting out complete all as spd and directed by EIC

Excavation in over areas n.exc 1.5m in deep in hard/dense soil and getting out complete all as spd and directed by EIC

Excavation in over areas exc 1.5m & n.exc 3.00 mtr in deep and n.exc 1.5m wide on plan in hard/dense soil and getting out complete all as spd and directed by EIC

M & L Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

Returning filling in including spreading leveling, watering and well ramming in layers not exc 25 cm in soft/loose soil.

Removing excavated material n.exc 50 M and depositing where directed at a level n.exc 1.5 M above from starting point complete.

M & L Plain cement concrete type D-2 (1:4:8) using 40mm graded stone aggregate as in foundation filling and mass concrete complete

M & L Brick work using fly ash bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete

M & L Brick work using fly ash bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete.

M & L Damp proof course 40mm thick in PCC 1:2:4 type B-0 to horizontal or vertical surface incl form work complete all as spd and directed by EIC

M & L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides of foundation and plinth beams and similar work.

M&L RCC 1:2:4 type B1 (20mm graded stone aggregate) in fdn, Plinth beam etc

M & L Formwork to sides of pillars, posts, struts, piers, columns and stanchions all as specified and directed

M&L RCC 1:2:4 type B1 (20mm graded aggregate) in Columns, pillars, piers, posts as per directed by EIC

M & L Form work to soffits of suspended slabs such as roof slab, floor slab not exc 200 mm thick complete.

M & L Reinforced cement concrete (nominal mix) ,type B-1, 1:2:4, (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns, and in shelves and the like complete.

M&L Form work to sides and soffits of beam, lintels, shelves etc complete.

Formwork to chullah hoods, chajjas, troughs and similar items including edges

M&L RCC type B 1, 1:2:4 (20mm graded stone agg) as in beams, cantilevers, lintels over 1.5 m span complete

M&L RCC type B 1, 1:2:4 (20mm graded stone agg) as in chajjas

M&L Mild steel TMT bars 10mm dia and over cut to lengh bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and incl MS wire not less than 0.9mm dia.

M&L Mild steel TMT bars 6 to 8mm dia and over cut to lengh bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and incl MS wire not less than 0.9mm dia.

M&L Mild steel TMT bars 5 to 10 mm dia, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips as in stirrups and spacers.

M & L Cement concrete type D-2, 1:4:8 ( 40 mm graded aggregate ) 75 mm thick as in sub base of floors complete all as spd and directed by EIC

M&L Sand filling under floors, founadation etc. including watering and consolidation complete all as specified and directed by EIC.

M & L Screed bed or bedding layer of mortar 10 mm thick on roof in CM 1:3 with WPC (Note WPC will be measured and paid seperately)

M & L Rendering 5mm thick on concrete surface as in ceiling in cement mortar 1:3 finished even and fair without using extra cement complete.

M&L 1 mm thick of Birla white putty/JK white wall care putty on new plastered surfaces and making the surface uniform & smooth.

M&L Two coats of distempering with oil bound distemper white or tinted on prepared smooth surface incl preparation of new plastered surfaces as in ceiling complete

M & L Two coats of cement base paint white or tinted on walls or fascia of roof or chajjas on new plastered plastered/painted surfaces of bldg complete all specified & directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet & edges will be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing

S&F Solid PVC factory made Door shutter of 30mm (style) consisting of frame made out of MS tubes for top bottom rails MS frame shall be ....PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beeding and jointed together with solvent cement as pere specification and drawing

S&F Aluminium handles, cast type, anodised of size 150mm D Shape

S&F 150mm long aluminium anodised barrel tower bolt complete.

S&F Stainless steel butt hinges, medium weight cold rolled of size 100 mm .

S & F Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete.

S & F Tubular towel ring, 20mm dia, fancy type complete.

S&F Brass chromium plated Shelf glass assembly with CP screws etc complete all as spd (Make-SEIKO/ Plumber/parryware/Essco)

S&F 15 mm dia bore PVC connections with PTMT nuts of length 600 mm long complete.

S&F White vitreous china WHB (1st quality) under counter oval shape of size 550x400mm including 32 mm bore CP waste coupling & 32 mm bore PVC waste pipe complete.

S&F 75 mm dia. PVC (SWR) multi floor trap with Stainless steel grating including jointing fixed in cement concrete type B-1 (1:2:4) complete.

M & L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

M&L 75 mm thick PCC (1:3:6) type C-2 using 40 mm graded stone agregate as in plinth protection /path & finishing even and smooth without using extra cement complete all as specified and directed by Engr - in - Charge. Note : Joints 12 mm wide to the full depth of PCC shall be provided at every 3 mtr and every change in direction and shall be filled wiith bitumen and sand 1:3 by weight. Cost of this provn shall be deemed to be included in the quoted rates.

S&F PVC (SWR) bends any radius of 75mm bore with acess door complete all as specified and directed.

S&F PVC (SWR) junction single, (Single T) equal or unequal any radius of 75mm bore with acess door complete all as specified and directed.

S&F PVC (SWR) pipe single socketed in any length with rubber ring joints fixed laid in trenches or in floors of 75mm dia complete.

S&F PVC (SWR) bends any radius of 110mm bore with acess door complete all as specified and directed.

S&F PVC (SWR) pipe single socketed in any length with rubber ring joints fixed laid in trenches or in floors of 110mm dia complete.

S&F PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall of 110mm dia complete.

S&F PVC (SWR) vent cowl of 110 mm bore of pipe complete all as specified and directed

S&F PVC (SWR) junction double, (double T) equal or un equal of 110 mm bore of pipe complete.

M&L DWC HDPE pipes class SN-8 laid and jointed complete as per manufacturer instruction in trenches of 150 mm ID/180 mm OD of pipe complete.

M&L Cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate complete

M & L Brick work using old size fly ash bricks in one brick thick honey-comb walling, built in built in cement mortar 1:4 complete

M&L Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in cover slab (for manholes etc) and similar work incl form work and set in CM 1:4 complete.

M & L Vitreous China squatting pan (1st Quality) ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests and P or S trap complete incl provision of lime concrete bedding. Make Parryware/Hindware/Jaguar

Supplying and laying of CPVC pipes 32 mm outer dia SDR 11 & Male & Female Brass Threaded Adaptor (MFTA & MTA/ MBTA & MFBTA) CPVC SDR 11 fittings in trenches complete all as specified

Supplying and laying of CPVC pipes 25 mm outer dia SDR 11 & Male & Female Brass Threaded Adaptor (MFTA & MTA/ MBTA & MFBTA) CPVC SDR 11 fittings on walls/ceiling or laying in floors incl chase cutting complete all as specified

Supplying and laying of CPVC pipes 32 mm outer dia SDR 11 & Male & Female Brass Threaded Adaptor (MFTA & MTA/ MBTA & MFBTA) CPVC SDR 11 fittings on walls/ceiling or laying in floors incl chase cutting complete all as specified

S & F Stop valves/angle valves 15 mm, fancy type chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed.

S & F Gun-metal, globe or gate valves 25 mm dia, with iron wheel head, screwed both ends for iron pipe

S & F Rotational moulded polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position 1000 ltrs capacity complete.

S & F Ball brass valves 25 mm dia, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule

S & F Bib taps 15 mm, chromium plated and fancy type long body cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule Make Prayag/Plumber/ESSCO/Parryware

S & F Dual type PVC valveless, syphonic action type, flushing cistern, low level, 10 ltrs capacity white, with inlet, ball valve, float and handle including brackets.

M&L Providing water proofing treatment over cleaned roof surfaces with super thermo APP modified water froofing membran comprssing of following for non-approachable roof: (i) Cleaning sweeping and washing and down with water to remove all dust etc from plastred roof surfaces/wall and filling of crack with sealing compound etc.(ii) Bitumen based primer conforming to IS 3384-1965 at 0.30 kg per sqm. (iii) One layer of super thermo APP modified water proofing membran with non polyster reinforcement of Make (M/S STP texsa Ltd/hyperplus membrane of M/S IWL India Ltd. M/S STP and Tikki Tar Ltd ) 3mm thick and minimum weight @ 3.50 Kg/sqm laid with gas torch and fasted on roof surfaces with roller. The over laps shall be sealed by flame including vertical surfaces after cutting necessary grooving and making good with PCC gola 1:2:4 type B1 etc adhere to bitumen all as per manufacturer instructions. (iv) Applying two coat of aluminium paint @ 0.20 kg/sqm per coat over bitumen layers as per manufacturer instruction (application including side lap overlaps shall be provided not less than 10cm and jointed sealed with torch as per manufacturer instruction specification.

S&F Anodised aluminium frame shutter as in partition, doors, windows, ventilators sliding/openable etc with one or more rebates including joining cleat for fixing etc. complete all as specified screws etc complete all as specified. Make : JINDAL/HINDALCO/INDALCO. Note : (i) Glazing and wire mesh shall be measured and paid separetely only as the labour element included in the relavent item. (ii) Item shall be paid as per weight of aluminium section (iii) The rate quoted shall be inclusive of the cost of neoprene beading, glazing pin, screws and powder coated fittings such as locking arrangement etc as required, which shall not be measured for arriving the weight (iv) The rate shall also be inclusive of complete packing with silicon gel around contacting surfaces of aluminium work, and including matching the existing.

S & F galvanised steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples.

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for and removing from the site.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and removing from the site.

M & L Providing 25 mm thick PCC type B0, 1 : 2 : 4, (using 12.50 mm graded aggregate) as in flooring complete with using WPC. WPC shall be measured and paid separately.

M & L Rendering 15mm thick in two layers (10 mm thick & 5 mm thick) on external surfaces on brick/concrete in CM 1:4 finished even and smooth without using extra cement with WPC. Note :- WPC measured and paid separatly

M & L Rendering 15 mm thick on fair faces on concrete surfaces (Roof slab) in CM 1 :4 with WPC as per manufacturer insruction complete. (WPC will be measured and paid separately)

M & L Rendering 10mm thick on ceiling surfaces in CM 1:3 finished even and fair without using extra cement.

M & L Cleaning sweeping and washing and down with water to remove all dust etc from plastred roof surfaces/wall and filling of crack with sealing compound etc. and application Bitumen based primer conforming to IS 3384-1965 at 0.30 kg per sqm complete.

S & F APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by torch application (including sider lap overlaps shall be provided not less than 10cm and jointed sealed with torch as per manufacturer instruction specification) including taking down existing APP membrane and removing upto 500 mtr away from working site complete. Make : M/S STP (Super thermolay)/IWL/SIKA.

M & L Applying two coats of bituminous anti-corrosive multi-purpose Aluminium Coating (SuperSilverShield) @ 0.15 kg/sqm per coat over bitumen layers as per manufacturer instruction

M & L 0.5 mm thick of Birla white putty/JK white wall care putty on new plastered surfaces and making the surface uniform & smooth on walls/ceilings.

M & L Preparation of old plastered surfaces and applying two coat of acrylic distemper on walls complete all as specified and as directed.

M & L Preparation of old plastered surfaces and applying two coat of acrylic distemper in ceilings complete all as specified and as directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding , and rubbish off the premises.

M & L Coloured Glazed ceramic tiles in vertical surface 600 x 300/450 x 300 x 7-8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10 mm thick screed in CM 1:4 complete.

Demolition and breaking up drain pipe (salt glazed stone ware, AC or reinforced concrete ) set in cement mortor any size internal dia of pipe complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M & L Brick work using sub class old size bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

M & L RCC M-25 Design Mix (using 20mm graded stone aggregate) as in slabs supported on walls, beams and columns, and in shelves and the like complete.

S&F in repair 15 mm dia concealed stop valves, cast copper alloy, CP fancy type with long shank and cup screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe. (Make : Jaguar/Parryware/Hindware)

S &F in repair chromium plated Shower rose 15 mm size, 125mm long with 300 mm arms (Make : Jaguar/Parryware/Hindware)

S & F 600 x 450mm bevelled edge mirror of 1st quality glass, mounted on 6mm thick commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete.(Make : Saint Gobain/ModiFloat)

S&F in repair 15 mm dia bore bib taps, cast copper alloy chromium plated fancy type with crutch alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule . (Make : Jaguar/Parryware/Hindware)

S & F of Vitreous China squatting pan, ‘Orissa’ pattern, size 630 x 450 mm white, with integral foot rests and PVC syphon of 110 mm dia as in repairs incl provision of lime concrete bedding complete.

Taking down and refixing of 15 mm dia Bib taps/Stop valves/Angle valves, cast copper alloy, fancy type chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe.

S & F Rubber hose 15mm size with brass nuts of length 450 mm all as specified and as directed. (Make : Jaguar/Parryware/Hindware)

S & F Stack clamps out of flat iron, round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete.

S & F in repairs CPVC pipes 20 mm outer dia SDR 11 & Plain CPVC SDR 11 includig all fittings on walls/ceiling or laying in floors including necessary cutting/chasing of walls and floors complete.

S & F in repairs CPVC reducing MBTA/FBTA 25 x 20 mm outer dia complete

Disconnecting existing water storage tank of capacity from 500ltr & not exc 1000ltr, setting aside (for lowering if required) for repairs, cleaning etc and re-fixing in position.

PVC (SWR) junction single, (Single T) 110 mm bore equal or unequal with acess door complete.

Excavation in trenches n.exc 1.5m deep & n.exc 1.5m wide on plan in soft/loose soil and getting out complete all as spd and directed by EIC

M & L 15-18 mm Granite slab (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

S & F Vitreuos china wash hand basin mounted top size 22 x 16 inches mm oval shape incl brackets or fixed to walls with anchor fasteners all cutting for and pinning in end of brackets or erecting stand, and inclusive of fixing and supply and waste pipe and CP waste coupling 32 mm dia complete fixed. (Make-Parryware/Hindware/Jaquar)

Taking Down Chowkhats or frames not exc. 1.5 sq. m each with shutters (without taking off shutters from the frames) complete.

Supply & fix in repair chomium plated fancy type pillar taps for wash hand basin for mixing hot and cold water screwed down for iron pipes suitable for 15mm bore pipe complete Engr-in-charge. (Make-Parryware/ Prayag/Hindware)

M&L Point wiring concealed type/surface conduit/casing and caping with 1.5sq mm PVC insulated unsheathed single core multithreaded copper conductor cable 1100 volts grade incl 1.5Sq mm PVC insulated sheathed copper conductor cable as earth continuity conductor drown through in and incl PVC rigid conduit/suface conduit/casing and caping not less than 20mm dia with its accessories pressed steel terminal box made of primer incld 3mm thick ISI marked laminated sheet cover for fixing switches/socket/regulators etc for the following: - make-plaza/polycab/KEI

One light/fan/bell point controlled by one No piano type switch 5 AMPS single pole one way

One socket outlet 5/3 pin 5 Amps controlled by one switch on the same board.

One 3 pin socket outlet 5 Amps independent board.

One 3 pin socket outlet 5 Amps on the same board with other switch.

S&F for 3 pin socket outlet point 15 Amps independent, with cables of size 2.5 sq mm multistranded, PVC insulated unseathed FR copper conductor cable, and 1.5 sq mm PVC insulated unseathed copper conductor cable as earth continuity conductor connected to common earth dolly all are in separate PVC conduit med grade not less than 20mm dia ISI marked ivory colour, incl. provn of sunken galvanised not less than 1.12 mm thick MS sheet pressed terminal boxes of suitable size & 3 mm thick laminated hylem sheet top cover of required size all as specified and directed by Engr-in-charge.

S &F Switch Piano Flush button single pole one way 5 Amp complete all as specified and directed. Make: Anchor/ Havells/ SSK

M&L for socket outlet 3/5 pin 5Amp flush type complete all as specified and directed. Make: Anchor/ Havells/ SSK

M&L Switch socket comination multipurpose 2 in 1,5 and 15 Amp Flush type ISI Marked complete all as specified and directed. Make: Anchor/ Havells/ SSK

S & F Building security light fitting 1 x 30W LED new generation energy saving & environmental friendly long life LED street light made up of pressure die cast aluminium housing with mid power LED as lighting source and PC cover having top opening including driver compartment driver with IP66 protection and impact resistance of IK07 including with suitable for 32mm dia medium grade G I bracket not exc 1.5 mtr length made to shape & fixing on pole/wall with 2 nos of MS clamp including necessary connection from LT OH line /buildings Make:- Havells/Crompton/Bajaj.

S&F in replacement of sheet metal enclousure for MCB DB single pole and neutral 8 way with 200 Amps rated bus bar 240 volts double door type complete all as specified and directed. Make : Legrand/ Havells/L&T

S&F in replacement of MCB SPN capacity 40 to 60 Amps DP 240 complete all as specified and directed. Make : Legrand/ Havells/ L&T

S&F in replacement of MCB SP 30 to 40 Amps 240 volts complete all as specified and directed. Make-Havells/legrand/ L&T

M&L Earthing complete with galvanized iron earth plate electrode 600 x600x6mm thick buried directly in ground (earth pit not less than 2.25 meters deep below normal ground level) with top edge of plate not less than 1.6 meter below normal ground level connected to galvanized earth lead wire 4 mm dia by means of bolts, nuts check nuts galvanized iron or steel all as shown in Electrical plate No. 3 of MES sch pt I testing on completion with & incl. 15 mm bore light grade GI protection pipe 7.5 mtr long for earth lead, PCC (1:3:6) pit with pre cast RCC (1:2:4) cover watering arrangement with funnel, wire mesh 20 mm bore light grade GI pipe, common salt & char coal fixing necessary excavation earth work complete. (GI pipe & GI wire beyond 7.5 mtr will be measured and paid respectively)

M&L in replacement of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area16sqmm 2 core Make-Polycab/Havells/KEI

M&L Ceiling rose , 3 terminal polycarbonate complete all as specified and directed. Make: Anchor/ Havells/ Philips

Taking down carefully aluminium point wiring (light, fan, socket or power ) complete, including fittings and fixtures such as switches, ceiling roses, light fittings, regulators, sockets etc., removing materials to store, or keeping in safe custody for re-use at site or offering credit, and making good disturbed surfaces of walls, floors, etc., all as specified and as directed.

M & L Switch Socket combination 2 in 1 , 5 pin, 6 Amps flush type.

S & F Lamp holder, PVC/ Polycarbonate type with back plate for batten/ angle fitting

M&L in replacment of Sheet metal enclosure MCCB DBs, Triple pole & neutral 4 way with 200 Amp rated bus bar double door suitable for 01 No incoming MCCB of 100Amp capacity and 12 Nos+ 12 Nos Out going MCB SP complete all as specified and directed. Havells/ L&T/Legrand NOTE:- MCCB & MCB's are measured and paid in separate items and same make.

S&F in replacement of MCCB 4 pole, 100 Amps with breaking capacity 16 KA, 415 volts complete all as specified and directed. Make : Havells/ L&T /Legrand

Supply & Fixing LED tube light complete fitting 1X20 Watt, 4 ft, 220V, AC decorative box type with high quality materials and design, extruded aluminum housing enhance safety, high quality PC diffuser, reliable and robust housing structure, efficacy is 125 Lumen/watt including connecting up with three core flexible copper conductor cable of suitable size upto ceiling rose complete all as specified & directed by Engr-in-charge.Product code- CCS-100-20-65-HL2-DP-NWH of Crompton Greaves or equivlent of Havells,Bajaj,HPL.

Taking out existing earthing system and M&L Earthing with galvanized steel earthing plate electrode 60 cm x 60 cm 6 mm buried directly in ground (earth pit not less than 2.25 mtr deep being ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level, connecting to a galvanised earth lead wire 4 mm dia by means of bolts, nut check nut and washers protected with and including 15 mm dia light grade GI pipe, necessary excavation and earth work, charcoal and common salt filling, watering arrangement with 20 mm GI pipe light grade including PCC pit with pre cast RCC (1:2:4) cover, GI funnel with test point, testing and commissioning all as specified and directed.

Sub main wiring complete with two runs of 6 sqmm single core PVC insulated unsheathed single core cable 1100 volts grade, multistranded with copper conductor drawn through and including 25 mm dia non metallic rigid PVC conduit and conduit accessories concealed in walls / roofs / floors etc., with one run of 4 Sqmm single core multistranded copper conductor as earth continuity conductor, all as specified inclduing dismantling unseriveable sub main wiring and accessories. Note:- One run of conduit two run of 6 sqmm copper condictor & one run of 4 sqmm copper conductor is measured as one unit.

Supply & Fixing ceiling fan complete with electronic type regulator and accessories 230 V, 50 HZ, 1400 mm sweep, energy saving.

Supply and fixing in replacement of metal Exhaust fans 300mm sweep ,Energy saving fans ,230V AC ,50 HZ Completed.

M&L in replacement of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 35 sqmm 4 core Make-Polycab/Havells/KEI

M&L Bricks common burnt sub class B designation for protection of cable complete all as specified and directed.

M&L Natural local river sand for cable protection.

M&L GI tubing 40 mm dia light grade with all fittings laid in trenches/making GI bracket of security lights/provn for ceiling fan ponit including bending of suitable size/support of UG cable as required at site as directed by Engr-in-Charge.

MS HARI MOHAN GUPTA

M/S ABHAY KUMAR AND BROTHERS