CA NO. GE (I) (AF)/SHL/ OF 2019-20 REPAIR/REPLACEMENT TO ROOF, CEILING, WALL PLASTERING, FLOORING, JOINERY, FLOOR/WALL TILING, INTERNAL WATER SUPPLY/PLUMBING, PLINTH PROTECTION, PATH INCL INTERNAL ELECTRIFICATION TO PSO BUNGLOW, COTTAGE AND CANTT-

Amount

B/R ITEMS Demolition of brick work/ block masonry or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles and removal all rubbish material complete all as specified directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness below or above ground level and removal all rubbish material complete all as directed.

Demolition of unreinforced cement concrete in any position not otherwise specifically provided for and removal all rubbish material complete all as specified and directed.

Dismantling of timber fillet, rails, post, rafters, purlins, etc. under 40 Sqcm in section unframed or framed work complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) & removing from site area n.exc 1.5 Sqm each complete all as specified and directed.

Taking down chowkats with shutters (without taking off shutters from the frames) & removing from site area exc 1.5 Sqm & n. exc 4.00 sqm each complete all as specified and directed.

Taking down door shutter of any description & removing from site area not exc. 1 sqm each complete all as specified and directed.

Taking down door shutter of any description & removing from site area exc. 1 sqm & n.exc 2.00 sqm each complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed trusses etc complete all as specified and directed.

Dismantling plain or corrugated steel sheeting/galvalume sheet any guage, thickness including Nainital or similar pattern roof covering,complete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking down cement or cement lime plaster any description, on brick or stone walls, etc. including raking out joints, hacking for key & scrubbing down with water, etc. & removing rubbish off the premises, complete all as directed.

Hacking out old broken glass (any thickness size quality or description) from wooden frames or stone concrete or brick surrounds, glazed with putty or fixed with beeds complete all as specified and directed.

Taking up or down steel tubing and connections alongwith bib tap, stop cocks and other fittings including cleaning for refixing or removal complete all as specified and directed :-

15mm bore.

20mm bore.

Dismantling of 110mm bore PVC(SWR) drain pipe alongwith fittings and accessories jointed in cement mortar and taking out from walls, floors or from trenches, if required complete all as specified and directed. (Note :- The length shall be measured along the centre line including fittings and accessoires).

M & L for sand filling under floor or in foundation including watering and consolidation, complete all as specified and directed.

M&L for hard core of broken stone or boulders of gauge n.exc 63 mm, deposited, spread & levelled in layers n.exc 15 cm thick watered & rammed to true surface complete all as specified and directed.

M&L for pre-cast cement concrete block masonry 1:3:6 Type C-1 using 20mm graded stone aggregate with solid blocks, exc. 10 cm in width and setting in cement mortar 1:4, complete all as specified and directed.

M&L for cement concrete type B1, 1:2:4 (using 20 mm graded stone aggregate) as in lintels upto 1.5m clear span, steps, seismic and other similar bands copping/cills, bed block for embedding hold fast etc including necessary form work weathering, slightly rounded or chamfered angles and throating complete all as directed .

Supply only integral water proofing liquid complete all as directed.

M & L for second class hardwood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads section area exc 13 Sqcm but n.exc 25 Sqcm complete all as specified and directed.

M & L for second class hardwood weather boarding, clean sawn, plain, 20 mm thick or feather edged 15 mm to 20 mm thick and fixed with 30 mm laps complete all as specified and directed.

S & F of 40mm thick second class hardwood (CHIR) boarding as in floors and skirting planed one side and edges tongued and grooved or rebated and fixed with nails complete all as specified and directed.

M & L for second class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S & F 35mm thick IInd Class Hard wood, plain framed, panelled door shutters, two panel with lock rail and panel of 9mm B.W.P. marine grade plywood bonded with high quality liquid phenol formaldehyde synthetic resin adhesive conforming to IS-710 or 12mm thick particle board veneered with commercial veneering on both faces (as ordered). The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I). Wood used shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed.

S & F 35mm thick glazed and skeleton door shutters open rebated of second class hard wood rail and styles, prepared to receive glass/gauge etc without sash bars, edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I). Wood used shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. (Note :- S & F Glass/gauge shall be measured and paid for separately)

S & F 30mm thick glazed and skeleton door shutters open rebated of second class hard wood rail and styles, prepared to receive glass/gauge etc divided into squares, with plain, chamfered or rounded, mitered and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I). Wood used shall be kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. (Note :- S & F Glass/gauge shall be measured and paid for separately)

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with mild steel square tube, In opening complete all as per specifications and drawings as applicable to item 08095 given in SSR Part – II (2010).

S & F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppy and fixing in the frame at site complete all as per specifications and drawings as applicable to item 08080 given in SSR Part–II.

S & F butt hinges, medium weight, colled rolled mild steel & ISI marked complete all as specified and directed for following sizes:-

75 mm long.

100mm long.

S & F 100mm long aluminium anodized barrel tower bolt of extruded section ISI marked complete all as specified and directed.

S & F 200mm long aluminium anodized barrel tower bolt of extruded section ISI marked complete all as specified and directed.

S & F 100mm size extruded aluminium alloy handles, fabricated type, anodised, ISI marked complete all as specified and directed.

S & F 150mm size extruded aluminium alloy handles, fabricated type, anodised, ISI marked complete all as specified and directed.

S & F 300 mm long aluminium alloy, anodised sliding door bolts, plate type with bolt not less than 16mm dia with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of cast aluminium alloy and fixed complete all as directed

S & F in repairs chromium plated brass tubular towel rail 20 mm dia, D type 60 cm long between flanges complete all as directed.

S & F in repair for powder coated mild steel drapery rod of 20 mm inner dia (in lengths as directed) of approved colour with and including decorative finial at both ends and pair of powder coated mild steel brackets fixed at both ends fixed with PVC rawl plug and steel screws on walls/beam, complete all as directed.

S & F Galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S & F mild steel work conforming to Fe-290 Gde E-165 as in hand rails, half round or other steel section or core for wooden hand-rail straight portion,drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc, wind ties for roof including securing bolts including all necessary drilling, bolting or riveting, etc. complete all as specified and directed.

S&F mild steel work in tubular trusses, purlins including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161 grade St-240 including notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts including rivets or nuts and bolts, providing and fixing cleats, fish plates, gusset plates etc and also for wedging, plumbing, turning up & fixing complete all as specified and directed.

S & F for pre-painted galvalume aluminum zinc coating GI based trapizoidal profile steel sheet 0.50mm thick (overall) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions complete all as specified and directed.

S & F for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick (overall) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions completed all as specified and directed.

S & F aluminium anodized (15 Micorn ) Glazed partition made out of aluminium extruded section 101x45x2mm thick with 12mm thick toughened glass panels including necessary jointing cleats, glazing clips, aluminium beading, neoprene dry set rubber gasket complete all specified and directed. (Note : 12mm thick toughened glass panels is deemed to be included in quoted rates)

S & F Non woven matt WALL PAPER suitable for residential & Light commercial interiors, Eco-friendly/latex-saturated 30% recycle 70% renewable cellulose fibres of paper width 76.2cm (finished width-71cm) weight 350gsm of high UV resistance, durable, water repellent, reach standard complaint, contribute to leed credits, recyclable with frame resistance of fire rated ASTM-E-84: class A(USA)/AS3837: Class 1 (Australia/NZ) untrimmed with 2cm bleed each side for durable cut installation and paste to wall with standard heavy duty paste complete all as specified and directed.

S & F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement complete all as specified and directed.

Material and labour for 5mm thick PVC sheet fillet of width 35mm for wall panelling and the like including fixing to walls to make PVC frame or as required complete all as specified and directed.

M & L for 75mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in sub base complete all as directed.

M & L for 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M & L for 20 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M & L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M & L for matt finish, joint less, coloured light shade vitrified ceramic tiles (square/rectangular), 10 mm thick (Premium quality), area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match with shade of the tiles complete all as specified & directed

M & L for prepolished cement concrete chequered tiles of size 400 x 400 x 25 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M & L 16-18 mm thick granite slab/tiles (of any type table rubbed and polished) in steps jambs pillars, window cills, cooking platforms and like set in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with complete all as specified and directed.

M & L Rounding to edges of stone slabs one edge, such as in steps,cooking platform, and other similar situations complete all as specified and directed.

S & F 10mm thick wooden laminated flooring floating glue less click locked (HDF based tongue and groove ) and sealed in a manner similar to a jigsaw puzzle on concrete slab/base/on hard wood flooring or virtually and other flat hard surface including 10mm thick under layer of EPE foam sheet of best quality complete all as specified and directed. (Make Action tesa or equivalant brand as approved by GE)

M & L for rendering 10mm thick in cement mortar 1:3 on fair faces of brick or concrete surfaces finished even and rough for receiving wall tiles/dado complete all as specified and directed.

M & L for rendering 15 mm thick on fair faces of brick masonry/ concrete surface in CM (1:6), finished even and smooth without using extra cement complete all as specified and directed.

M & L for 15mm thick rendering in CM 1:4 on fair faces of brick masonry/concrete surfaces, mixed with water proofing liquid @ 150ml per 50 Kg bag of cement and finished even and smooth without using extra cement complete all as specified and directed. (Note :- Supply only Water Proofing Liquid shall be measured and paid separately)

M & L for glazed ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M & L for glazed ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M & L for joint less, coloured light shade vitrified ceramic tiles (square/rectangular), 10 mm thick (Premium quality), area of each tiles not exceeding 0.36 sqm, as on vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

S & F 4mm thick sheet glass ordinary quality and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all specified and as directed.

M & L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 1mm thick wall care putty complete all as directed. (Make : For wall putty- Birla white/Bison wall putty of Berger/Narolac wall putty/Asian paint powder putty /Acro wall guard.)

M & L for preparing old plastered surfaces of wall and applying one coat of oil bound distemper complete all as per specified and directed.

M & L for preparing newly plastered walls surfaces and applying two coats of plastic emulsion paint over a coat of priming paints plaster coat complete all as specified and directed.

M & L for preparation of old treated surfaces and applying one coats of plastic emulsion paint complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces of wall, applying a coat of 1mm thick wall care putty and applying two coats of weather proof acrylic paint over one coat of exterior grade acrylic primer complete all as specified and directed. Make-Apex Ultima of Asian, weather shield MAX of ICI/Dulux, weather coat long life of Beger, Acroguard 3X of Acro paint.

M & L for preparation of old painted concrete/plastered wall surfaces including cleaning the surfaces by wire brushes and washing and applying one coat of acrylic antifungal exterior emulsion painting on walls complete all as specified and directed. Make-Apex Ultima of Asian, weather shield MAX of ICI/Dulux, weather coat long life of Berger/Excel Total of Nerolac.

M & L for preparation of old painted concrete/plastered floor surfaces over 10cm in width or girth including cleaning the surfaces by wire brushes and washing and applying one coat of terracota colour acrylic antifungal exterior emulsion painting on floor of PCC Chequered tiles complete all as specified and directed. Make-Apex Ultima of Asian, weather shield MAX of ICI/Dulux, weather coat long life of Berger/Excel Total of Nerolac.

M&L for preparing surface of timber piles and dipping in a hot mixture of tar and creosote in the proportion of 20 kg coal tar pitch to 25 litres of creosote oil for 4 mins complete all as specified and directed.

M & L for French Polishing on old wooden or wood based surfaces of any description width or girth including cleaning and preparing the old surface with two or more coats complete all as specified and directed.

M & L for preparation of new or previously untreated wooden or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of 1st grade quality over and including one coat of pink primer complete all as specified and directed.

M & L for preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of 1st grade quality over and including one coat of red oxide zinc chrome primer complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint of 1st grade quality complete all as specified and directed.

S&F steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed for following sizes:-

15mm bore.

20mm bore.

Fixing only old serviceable steel water tubing, galvanized, medium grade, with all new fittings, fixed to walls and ceiling or in floor complete all as specified and directed for following sizes:-

15mm bore.

20mm bore.

S & F 15mm bore bib tap cast copper alloy fancy type chromium plated long body with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F 15mm bore stop valve cast copper alloy chromium plated, fancy type screwed down high pressure long shank and cup concealed type with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and directed.

S & F in repairs 15 mm dia cast copper alloy Chromium plated Angle valves, with wall flange concealed type screwed down for iron pipe or for unions complete all as specified and directed. (Product Code & Make :- Cat Part No.- 8710 of Make Prayag or equivalent model of other makes listed in list of makes).

S & F in repairs 15 mm dia cast copper alloy Chromium plated two way Angle valves, with wall flange concealed type screwed down for iron pipe or for unions complete all as specified and directed. (Product Code & Make :- Cat Part No.- 8711 of Make Prayag or equivalent model of other makes listed in list of makes).

M & L in repair for 15 mm dia cast copper alloy Chromium plated two way Bib cock with wall flange concealed type screwed down for iron pipe or for unions complete all as specified and directed. (Product Code & Make :- Cat Part No.- 8712 of Make Prayag or equivalent model of other makes listed in list of makes).

S&F in repair 15 mm dia Brass CP, wall mixer 3 in 1 system with provision for both hand and overhead shower complete with 115 mm long bend pipe, connecting legs and wall flange (without Hand and overhead shower) (Concealed type) screwed both ends for iron pipe or for unions complete all as specified and as directed. (Product Code & Make :- Cat Part No CON-281KN of JAQUAR or equivalent model of KOHLAR/Roca)

S & F in repairs 15mm bore sink mixture for mixing hot and cold water chromium plated fancy type with swinging casted spout (wall mounted model) with connecting legs & wall flanges two joints to steel pipe or union and plugging/screwing to wall complete all as specified and as directed. (Product Code & Make :- Cat Part No CON-309KN of JAQUAR or equivalent model of KOHLAR/Roca)

S & F in repairs 15mm bore central hole Basin mixture for mixing hot and cold water chromium plated fancy type without popup waste system with 450mm long barided hoses complete all as specified and as directed. (Product Code & Make :- Cat Part No CON-167KNB of JAQUAR or equivalent model of KOHLAR/Roca)

S & F in repairs Hand Shower (Health Faucet) with 8mm dia 1 metre long flexible tube with wall hook complete all as specified and as directed. (Product Code & Make :- Cat Part No ALD-573 of JAQUAR or equivalent model of KOHLAR/Roca)

S & F in repairs Hand Shower of 95mm dia round shape multi flow with 8 mm dia and 1.00 mtr long flexible tube and wall hook complete all as directed. (Product Code & Make :- Cat Part No HSH-1739 of JAQUAR or equivalent model of KOHLAR/Roca) (Note : The contractor shall deposit with Engineer-in-Charge these original purchase voucher and product guarantee/warrantee certificate in original for the period as per policy in vogue of manufacturer to obtain service from manufacturer during the period of guarantee/warrantee.)

M & L for gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 20mm dia complete all as specified and directed.

S & F in repairs PVC connection pipe 15mm dia with PTMT nuts of length 450mm complete all as specified and directed.

S & F in repairs 450mm long CP brass connection pipe with CP brass nuts on both ends for fixing to pipe or other fittings complete all as specified and directed.

S & F PVC (SWR) pipes 110mm bore size single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F in repairs sink with drainage board made of stainless steel 1mm thick kitchen sink with plugs, washers and wastes, including bedding cement mortar on to dwarf wall or including fixing cantilever brackets and connecting unions to pipe, over all size 915mm x 460mm bowl size 410 x 330mm x 160mm, complete all as specified and as directed.

M&L for disconnecting existing tanks, setting aside (or lowering if required) for cleaning etc and hosting if required, reconnectings and refixing in position including cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes etc. for the capacity of tanks exceeding 250 and not exceeding 500 Litres complete all as specified and directed.

S & F in repairs vitreous china wash basin, white, flat back, size 550 x 400 mm including one No PVC waste pipe 25 mm dia and 75 cm long with 32 mm dia connector, 32mm size waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange end, bedded in red lead cement and other fixed complete including cutting for and pinning in ends of bracket or erecting stand complete all as directed.

S & F in repairs vitreous china wash basin OVAL type with granite counter including cutting for and pinning in ends for bracket, and waste fittings 32mm including waste pipe, brass chromium plated with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

S & F in repairs white Vitreous china wash down water closet pan (pedestal pattern) with integral S trap including plastic water closet seat, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device including flush pipe and fixing bolts (excluding flushing cistern) etc complete all as specified and directed. (Product Code & Make :- Cat Part No CNS-WHT-WH-10 of JAQUAR or equivalent model of other makes listed in list of makes).

S&F in repair single piece Suite white Vitreous china wash down water closet pan (pedestal pattern) with integral Vitreous china flushing vistern including plastic water closet seat and cover,complete all as specified and directed. (Product Code & Make :- Cat Part No C844A Qube of Parryware or equivalent model of other makes listed in list of makes).

S & F in repairs vitreous China squatting pan (Orissa pattern) water closet (white) of size 580 mm x 440 mm with integral foot rests, 'P' or 'S' trap, including connection to trap, flushing pipe and antisyphonage pipe etc and including provision of PCC (1:5:10) type E-2 lean concrete in filling, making good to floor (excluding flushing cistern and flush pipe etc) complete all as specified and directed.

S&F in repairs, PVC low level cistern 10 litres capacity, valve less, symphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density & bracket etc complete all as specified and directed.

S & F in repairs plastic water closet seat, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F in repairs chromium plated toilet paper holder with flap complete all as specified and directed. (Product Code & Make :- Cat Part No. BA-38 of Make Prayag or equivalent model of other makes listed in list of makes).

S&F in repairs CP Soap Dispenser with glass bottle complete all as specified and directed. (Product Code & Make :- Cat Part No. BA-33 of Make Prayag or equivalent model of other makes listed in list of makes).

S&F in repairs glass shelf 500 x 125mm with decorative and ornamental side supports and front lining of chromium plated fixed with screws and glass with as shelf supported over frames all as specified and all as directed. (Product Code & Make :- Cat Part No. BEA-45 of Make Prayag or equivalent model of other makes listed in list of makes).

S&F in repair corner glass self of size 300mm radius (with brass chromium plated brackets) fixed in the walls with necessary screws etc. complete all as specified and directed. ((Product Code & Make :- Cat Part No. BEA-44 of Make Prayag or equivalent model of other makes listed in list of makes).

S & F in repairs PTMT alloy toilet cabinet with mirror of overall size 622 x 422mm and fixed to wall complete all as specified and directed. ((Product Code & Make :- Cat Part No. 556 of Make Prayag or equivalent model of other makes listed in list of makes).

E/M ITEMS Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete from existing conduits, from PVC Casing/capping with all fittings, such as switches, ceiling rose, pendants, sockets, lamp holder, fan regulators, sketch/brackets light fittings (except tube light fitting) etc and removal of old material from site (except switches, sockets and fittings to be reused) and making good disturbed surfaces of walls, floors ceiling etc complete all as specified and directed to match with existing surfaces.

Taking down old unserviceable light fittings any type and removal from site and making good disturbed surfaces of walls, ceiling etc complete all as specified and directed to match with existing surfaces.

M & L for point wiring complete with 1.5 Sqmm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS-H cable PVC rigid non metallic conduit (minimum 20mm bore size) and conduit accessories concealed in walls/ceiling/floors all as per IS including sunk type pressed steel terminal boxes (Heavy duty) with 3mm thick plastic laminated bakelite sheet top cover for mounting switches, sockets, regulators, bell push etc, including 1.5 Sq.mm solid copper conductor with green PVC FRLS-H insulated unsheathed earth continuity conductor to common earth & connecting to earth dolly for the following :- (Note : The rate quoted shall deemed to include for cutting chases for concealing PVC conduit and making good disturbed surfaces. )

One light point/fan point/bell point controlled by one, one way switch.

One 5 Amps socket outlet/switch socket outlet on independent board.

One 5 Amps socket outlet/switch socket outlet on same board with other switches.

M & L for point wiring complete for 15 Amps socket outlet on independent board with 2.5 Sqmm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS-H cable drawn through and including PVC rigid non metallic conduit (minimum 20mm bore size) and conduit accessories concealed in walls/ceiling/floors all as per IS including sunk type pressed steel terminal boxes (Heavy duty) with 3mm thick plastic laminated bakelite sheet top cover for mounting switches, sockets, including 2.5 Sq.mm multistranded copper conductor with green PVC FRLS-H insulated unsheathed earth continuity conductor to common earth & connecting to earth dolly. Notes : The rate quoted shall deemed to include for cutting chases for concealing PVC conduit and making good disturbed surfaces.

M & L for point wiring complete for 15 Amps socket outlet on independent board with 4 Sqmm single core multistranded copper conductor of 1100 volts grade PVC insulated and unsheathed FRLS-H cable drawn through and including PVC rigid non metallic conduit (minimum 20mm bore size) and conduit accessories concealed in walls/ceiling/floors all as per IS including sunk type pressed steel terminal boxes (Heavy duty) with 3mm thick plastic laminated bakelite sheet top cover for mounting switches, sockets, including 4 Sq.mm multistranded copper conductor with green PVC FRLS-H insulated unsheathed earth continuity conductor to common earth & connecting to earth dolly. Notes : The rate quoted shall deemed to include for cutting chases for concealing PVC conduit and making good disturbed surfaces.

S & F switch piano flush type 5/6 Amps, single pole, one way, 230 Volts complete all as specified and directed.

Supply and Fix Socket outlet 2/3 pin 5 Amps, flush type, complete all as specified and directed.

S & F switch socket combination two-in-one (multipurpose), 5 pin , 5/6 Amp, flush type, 240 Volts complete all as specified & directed.

S & F switch socket combination two-in-one (multipurpose), 6 pin, 5 Amp and 15 Amp, flush type, universal 240 Volts complete all as specified & directed.

S & F lamp holder, PVC / polycarbonate type with back plate suitable for Angle fittings complete all as specified and directed.

S & F ceiling rose, three terminal, PVC / poly carbonate isolated body, complete all as specified and directed.

Supply and fix LED tube light batten fitting, 18 Watt 230 V, 50 Hz with with all standard fittings etc pre-wired including LED tube and connecting the fitting from ceiling rose/connector using copper flexible cord of size 1.5sqmm, 3 core of suitable length complete all as specified and directed. {Model/Make : Cat Part No BLRB-DB 118 for tube light fitting and Cat Part No. BLRB 18W CW for LED tube light of make Bajaj or equivalent model of makes listed in List of makes}.

Supply and fix LED tube light fitting, baton integrated LED channel 10 Watt 230 V, 50 Hz with with all standard fittings etc pre-wired including LED tube, colour temperature neutral white and connecting the fitting from ceiling rose/connector using copper flexible cord of size 1.5sqmm, 3 core of suitable length complete all as specified and directed. {Model/Make : Cat Part No BCLSB 10 NW of make Bajaj or equivalent model of makes listed in List of makes}.

M/S BISWA CONSTRUCTION

M/s Gupta Construction