Repairing, Rewinding of 10 nos. of Horizontal Electro Motor and Heat Vernish of 30 nos. of Horizontal Electro Motor of Different R.L.I. Schemes under AE AM, Tamluk AM Sub Division under EE AM Tamluk AM Division under Non Plan Programme.

Repairing, Rewinding of 10 nos. of Horizontal Electro Motor & Heat Vernish of 30 nos. of Horizontal Electro Motor of Different R.L.I. Schemes under AE(A-M),Tamluk(A-M) Sub-Division under EE(A-M) Tamluk(A-M) Division under Non-Plan Programme. ( Please see the details in Sheet Schedule )

Please Enable Macros to View BoQ information

BoQ_Ver3.0

Tender Reference No : WBWRDD/EE/TAM_eNIT14_25-26

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

Repairing, Rewinding of 10 nos. of Horizontal Electro Motor & Heat Vernish of 30 nos. of Horizontal Electro Motor of Different R.L.I. Schemes under AE(A-M),Tamluk(A-M) Sub-Division under EE(A-M) Tamluk(A-M) Division under Non-Plan Programme.

(a) Dismantling of different H.P 3 Phase 380-400 Volt 1440 RPM, 4/3 pole 50 cycle for induction motors, removing old burnt out coil from slots carefully, segregating all the parts, washing and cleaning the same thoroughly for verification of serviceable and unserviceable parts as per direction of E.I.C (ii)17.5 H.P/ 20 H.P 3 phase induction motor.

Rewinding with approved quality Super Enamel copper winding wire of standard guage as provided by motor manufacturer including slot insulation as per Indian Electrical Rules, shouldering the cable joints properly, taping with 660 V. Grade water proof tape, making new loop terminals heating and vernishing with 'E' class golden vernish (Jhonson & Nicolson make) so as to develop original rated rpm, supplying all necessary materials as mentioned above and reassemblying the motor. (b) 17.5 H.P/20 H.P 3 Phase, 415 votls, 50 Hz, 2/4 pole induction Motor(i) Supply of super enamelled dual coated copper wire conforming IS 13730, 1996, part 13 (18 swg to 22 swg Required max. weight of super enamelled copper wire is given below: 1) Elmech/G.E.C(New)/Crompton/N.E.C - 10.2Kg/each

(ii) Labour charge for rewinding , soldering, heat varnishing, bearing changing, reassemling etc. including supply of all materials excluding bearing as mentioned above complete in all respect as per direction of E.I.C

Testing of repaired motor by contious 8 hrs running on load as per direction of E.I.C.

Labour charge for carriage of motor from store to workshop and back to store after repair. This item is only applicable when written permission is available from E.I.C. where there is no facility for such work in the sub- division.

Heat varnishing with best quality (Johnson & Johnson / Dr. Beck/ Giliander) class 'E' insulating varnish of required quantity for 3 course & uniform heating at 80° C for 48 hrs. with all cost of materials, labour ar per direction of E.I.C. (Where rewinding is not required). (c) Insulating varnish 1 lit for 20 HP induction motor

Painting two coats of both inner & outer portion with best quality synthetic enamel paint (to be approved before use) including smoothing surface by sand paper for removing old paint as per direction of E.I.C. (a) Motor

(b) Pump

Less Deduction towards dismantled burnt enamelled copper wire from induction motor on the basis of actual measurement to be retained by the agency. minimum 8 Kg per Motor

Total Rs.

Add GST @ 18 %

Sub Total Rs.

Add Cess @ 1%

Grand Total Rs.

Say Rs.

Rupees Two Lakh Three Thousand One Hundred & Thirty Eight Only