SPL REPAIR TO SUB MAJ LIVING ACCN, PANF LINE, JCO SINGLE LIVING MT AREA, MEAT CUTTING ROOM, SOLAR PORTION, FENCING AROUND SOLAR WATER HEATERS OF BOYS AND GIRL AREA DGNCC AND PROVN OF VEHICAL PARKING SHED NEAR CONTROL ROOM DELHI AREA PROVOST UNIT UNDE

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 Sqm each and removing to store complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sqm but n.exc 4 sqm each and removing to store complete all as specified and as directed.

M&L Aluminium alloy powder coated windows including aluminum powder coated frames sliding track, bottom weighing not less than 1.015 Kg/RM, sides and top not less than 0.826 Kg/RM double revated and 0.55Kg/RM for window shutter with one fixed glazed shutter and two nos glazed/gauged shutter sliding type with aluminium sections as per series - A (15mm) 3 track of Jindal section numbers for sliding windwos with framed shutter including aluminium allow powder coated snap type beads handles with locking arrangement spring action and glazing clip joint cleats rubber gaskets etc including provision of 5.5mm thick tinted glass/frosted glass of superior quality and stainless steel jali including all standard fittings, complete all as specified and as directed.

M&L Aluminum alloy powder coated door including frame and channel of section (Door frame single groove 101.6mm x 44.45mm x 2.1mm, shutter top section 47.62mm x 44.45mm x 1.95mm thick, shutter bottom section 114.30mm x 44.45mm x 2.15mm thick, shutter vertical section 85mm x 44.45mm x 1.80mm thick, shutter middle section 83.50mm x 44.45mm x 2.40mm thick & glazing clips weighing not less than 0.097 Kg/RM) including shutter fixed to sliding type/openable frame and channel as directed and approved by GE and as per IS specifications including provn of 5.5mm thick tinted glass/12mm thick prelaminated particle board as required including handles, tower bolt, floor spring heavy duty “SAMRAT” , locking arrangement “GODREJ”, rubber gasket and door stopper complete.

Aluminium alloy powder coated standard hollow section for ventilotors as per approved sample and as per IS specifications, shutters weighting 0.55 kg/RM, rectangular frames of section 101.6mm x 44.45mm x 3.18mm weighing not less than 2.54Kg/RM including provision of 5.5mm thick tinted glass of superior quality including handles, tower bolt, hinges and all standard fittings complete all as specified and as directed.

S & F Solid PVC door frame of size 50mm x 95mm made out of wood grain printed PVC sheet used reinforced with M.S. tube, suppling & fixing in opening as per specification & drawing complete all as specified and as directed.

S & F Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front and back Face (wooden finish pattern), supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

S & F framed work such as in door frame, door shuters / gate of angel or other section with gusset plates, rails, braces, etc complete , drilled for fixing of steel sheeting or other covering. Doors, etc to be prepared for hanging or sliding with and including either hooks and hings or steel hanging door fittings, including hings hold fast of Fe 410-W (Gde E-250 quality) etc complete all as specified.

S & F Mild steel, plain, black sheet 1.60mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and as directed.

S & F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete.

S & F 125mm size medium weight cold rolled mild steel butt hinges complete all as specified and as directed.

S & F 100mm size stainless steel butt hinges to PVC frames with reqd nos of screws complete all as specified and as directed.

S & F Aluminum Anodised 150mm size barrel tower bolt with complete all as specified and as directed.

S & F 150mm size aluminum adodised handles complete all as specified and as directed.

S & F 150mm size Mild steel oval shape handles complete all as specified and as directed.

S & F for steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified.

S & F for steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars complete all as specified.

S & F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples.

S & F 3mm thick Sheet glass, ordinary quality and glazing with oil putty in squares n exc 0.5sqm in each panes

S & F Mild steel framed work as in grills, gratings etc, with end of bars shouldered and or riveted forged into spikes, framed guard bars, barred iron doors, ladder, framed balusters, railing, frame work for water tanks and similar works, complete conforming to Fe 290 Gde E-165, complete all as specified and directed.

M & L for Brick work with sub class 'B' bricks of old size, straight or curved on plan to any radious built in CM 1:6 including demolition of Brickwork built in cement mortar including all quioins, arches, pillars etc complete all as specified.

Taking down cement or cement lime plaster , any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M & L for 15mm thick rendering in cement mortar 1:4 on fair face of brick walls/ concrete surfaces and finished even and smooth without using extra cement in any position incl scafolding etc, complete all as specified and as directed.

M & L for 15mm thick rendering in cement mortar 1:6 on fair face of brick walls/ concrete surfaces & finished even and smooth without using extra cement in any position incl scafolding etc, complete all as specified.

M & L rendering 10 mm thick on concrete surfaces as in ceiling in CM 1:3, finished even and smooth without using extra cement complete all as specified and as directed.

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for etc complete.

M & L for form work to soffits of suspended slabs such as roof slabs, floor, slabs landings and stair and similar work not exc. 20 cm thick flat rough to receive plaster all as specified and directed.

M & L for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete.

M & L for mild steel TMT bar 10mm dia and over cut to length,bent to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M & L for RCC M25 Design Mix using 20mm graded agg as in slabs, supported on walls, landings, balconies and in shelves and the like complete all as specified and as directed.

M & L for 75 mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection laid in bays & surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for 75mm thick Cement concrete 1:4:8 Type D-2 (using 40mm graded agg) as in sub base of flooring or in any position.

M & L for coloured Chequered cement concrete tiles 25cm x 25cm x 20-22mm thick, set, jointed and pointed in neat cement slurry over and incl 15mm thick screed bed in CM 1:6 including demolition of existing flooring or tiles of any type and size complete all as specified and as directed (Note: Colour of chequered tiles shallbe approved by Engr-in-Charge or by GE as per site requirement).

M & L for Non-Skid coloured ceramic tiles 7-8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick screed bed in CM 1:6, including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), complete all as specified and as directed.

M & L for glazed coloured ceramic tiles in vertical surface 300x600x7 mm thick (with pattern and border work as required at site) set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick screed bed in CM 1:4 including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), complete all as specified and as directed.

M&L Machine cut kota stone slab flooring 20-25mm thick over and incl 15mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including dismantling of existing tiles of any type complete all as specified and as directed.

M & L for coloured vetrified tiles of size 600 x 600 x 8-10mm thick as in floor over 15mm thick screed bed 1:6 in cement mortar, set and jointed in white cement with pigment to match including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), complete all as specified and as directed.

S & F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confrming to IS 1161-1979 grade St-240 including dismantling of existing steel work of any type complete all as specified and directed

S & F painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of existing AC sheet corrugated or semi corrugated as in roof coverings complete all as specified and as directed.

S & F painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling of existing AC sheet corrugated or semi corrugated as in roof coverings complete all as specified and as directed.

S & F designer board false ceiling of size 600x600x4mm thick white prelaminated sett embosed reinforced tiles of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers of GI wire 4mm dia to be fixed by approved rawl plug, level and justers and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture instruction including taking down the existing false ceiling of any type with frame work complete all as specified and directed.

S & F in repair vitreous china pedastal pattern water closet (EWC) including flush pipe & seat cover 'P' or 'S' trap, Jet spray and Health faucet complete all as specified and directed.

S & F in repair Vitreous China squatting pan 'Orissa' pattern size 580 x 440 mm white, with integral foot rests with connection to trap , and to flushing pipe antisyphonage pipe including trap set in concrete etc complete and making good to floor all as specified and dirtected.

S & F in repairs Vitreous china floor mounted WC ( Cascade) one piece type (off white) including connecetion in drain etc incl water closet seat cover CP jet spary, flushing cistern, with P or S trap with all fitting and fixture complete all as specified and as directed.(Make : Jaquar or equivalent in Cera/Parryware)

S & F in reapir 10 Ltrs capacity PVC valveless symphonic action type flushing cistern white low level with inlet, ball valve float handle including bracket and flush pipe etc complete all as specified and directed

S & F Rotational moulded polyethylene water storage tanks 2000 lts capacity, double layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PTMT ball valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed including taking out existing unserviceable overhead tank of any description complete.

S & F in repair 15mm bore, fancy type CP bib tap of cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified. (Make: Jaquar/Marc/Kohler)

S & F in repairs cast copper alloy Chromium plated Angle valve 15mm bore complete all as specified and as directed. (Make : Jaquar/Marc/Kohler)

S & F in repairs PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and as directed.

S & F in repairs 75mm dia brass chromium plated shower rose with neck and swivel joints fancy type with shower armof 450mm long suitable for 15mm bore GI pipe all as specified and directed. (Make: Jaquar/Marc/Kohler)

S & F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed. (Make: Jaquar/Marc/Kohler)

S & F in repairs 20mm dia Chromium plated towel rail 60cm long fixed to wall including all fittings for fixing complete all as specified and directed. (Make: Jaquar/Marc/Kohler)

S & F in repairs Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed.

S & F Stainless steel Grating dome 125mm dia with or without hole for waste pipe, fixed in repairs, complete all as specified and as directed.

S & F in repairs PVC (SWR) Floor/Nahani trap, plain dia of outlet 125mm, complete all as specified and as directed.

S & F Vitreous china wash basin counter oval type size 600x425x195mm, under granite slab with all fitting and fixture, fixed in repairs, complete all as specified and as directed.

S & F tubing 15mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down GI tubing 15mm bore and connections complete all as specified and directed.

S & F tubing 20mm bore medium grade, galvanised, ISI marked with all fitting and fixed complete to walls and ceilings or laid in floors including taking up or down GI tubing 15mm bore and connections complete all as specified and directed.

S & F in repairs 15mm bore Gun-metal, globe or gate valves, with iron wheel head screwed for iron pipe of 15 mm bore complete all as specified and directed.

S & F in repairs 20mm bore Gun-metal, globe or gate valves, with iron wheel head screwed for iron pipe of 15 mm bore complete all as specified and directed.

M & L 20 mm thick granite (Z black colour) of any type work table rubbed and polished as in steps, jambs, pillars, window cills, cooking platforms and like in over 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab , notching and moulding including demolition of existing granite complete all as specified and as directed .

S & F in repairs Brass CP basin mixer central hole, for mixing hot and cold water fixed as per manufacture's manual, with long shunk and cup washers, screwed both ends suitable for 15mm bore GI pipe joints to GI pipes or unions, complete all as specified and as directed. Make & Cat Part : Jaquar-Cat No. KUP-35051BPM, Jaquar-Cat No. KUP-35005BPM, Kohler-Cat No. K-74013IN-4BND-CP, Kohler-Cat No. K-74026IN-4BND-CP.

S & F Designer type high quality fancy type looking mirror of size as approved by Engr-in-Charge 8-10mm thick, fixed to wall with stainless steel studs, screws, brackets and washers etc complete all as specified and as directed.

S & F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S & F in repairs glass corner shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed.

S & F in repairs Sinks with drainage board made of stainsless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortor on to dwarf walls or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx 160mm all as specified and directed.

S & F in repairs Fancy type sink mixer for mixing hot and cold water with swinging port, screwed for iron pipe,15mm bore complete all as specified and as directed. (Make : Jaquar/Marc/Kohler)

S & F in repairs 100mm dia Cast iron soil (Sand Cast), waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or fixed to wall or in floors complete all as specified and as directed.

S & F in repairs 100mm dia Cast iron Bends (any radius), diminishing pieces or tapers (larger bore measured) complete all as specified and as directed.

S & F in repairs 100mm dia cast iron cowls complete all as specified and as directed.

S & F in repairs 100mm dia Stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed.

S & F 110mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints fixed to walls or laid in floors as sanitary fittings, rain water pipes etc in any position including taking down, eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads,shoes, bends, swan-necks, etc. complete all as specified and directed.

S & F in repairs 110mm bore PVC (SWR) bends any radius complete

M & L two coat of synthetic enamel paint (finishing coat) over one coat of primer to new steel surfaces of any description over 10 cm width or girth incl prepration of surfaces complete all as specified.

Eacavation in trenches not exc 1.5m wide and not exc 1.5m in depth for foundation exc on for walls, shafts, manholes not exc 10 Sqm on plan or for laying pipes/cables etc and getting out in soft/loose soil complete all as specified and as directed.

Returing filling in incl spreading levelling watering and well ramming in layers not exceeding 25cm in soft or loose soil complete all as specified and as directed.

Removing excavatged matereials to a distance not exc 50m and depositing where directed at a level not exc 1.5m above the starting point in soils complete all as specified and as directed.

M & L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation, filling and mass concrete all as specified and directed.

M & L for PCC 1:2:4 type B-1 using 20mm graded stone agg as in surface channels complete.

Demolition and breaking up drain pipes (SGSW/ AC/RCC) including hunching and benching set in cement mortar for 150mm to 300mm dia pipe, and removal of debris from site and deposited where directed at a distance not exc 1KM from site complete all as specified and as directed.

M & L for 200 mm dia (internal dia) RCC hume pipe class NP -2 laid and and jointed complete with colleres complete laid in trenches and tested complete all as specified and as directed.

M& L for PCC 1:3:6 type C2 using 40 mm grade stone aggregate as in bed to drain pipe 200 mm bore incl forming cradles complte all as specified and directed.

S & F for factory made Precast RCC manhole covers 75 mm thick medium duty conforming to IS-12592, including demolition of existing manhole covers complete all as specified and as directed.

M&L for Plain Cement concrete 1:2:4, type B-1 using 20 mm graded crushed stone aggregates as in lintels up to 1.5 metre clear span, bed blocks, copings and the like including weathering, slightly rounded or chamfered angles & throating including provision of necessary formwork, complete including demolition of existing coping all as specified and as directed.

Taking out exisitng roof treatment with any type of membrane, wire brushing and cleaning top surface of tiles, cement concrete, including flashings and junction of parapets and taking out grass roots/vegetation etc., from existing roof surfaces and cleaning the surface after drying from dirt, mortar, dust mortar buds, algae and all other foreign matter and brushed and wiped and drying the cleaned surface for further treatment, complete all as specified and as directed.

M & L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 finished even and smooth without using extra cement including a mix of water proofing compound @ 200ml/50Kg Cement Bag (Smartcare vitalia of Asian Paint product or equivalent of Berger and Nerolac), complete all as specified and as directed. (Note : Cost of water proofing compound shall deemed to include in the quoted rate).

Providing and applying Smartcare Dampproof, a fibre reinforced elastomeric liquid water proofing membrane formulated with reinforcing acrylic fibers having Sun Reflectivity Index (SRI) of 105 on horizontal/vertical surfaces of roof/wall/chajjas in multiple coats @2.0 litre/sqm. Primary coat is self-priming coat of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1, damp proof : water) and other coats to be applied undiluted. The coating needs to be reinforced with 40 GSM geotextile, to sandwiched between 2nd & 3rd coat of coating. The application shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes complete in all respect as per the direction of Engineer-in-Charge. (Make: SmartCare Damp Proof of Asian Paints or equivalent in Berger and Nerolac). (1) The work shall be executed through authorised applicator of manufacturer only. (2) Authrised Applicator shall be approved by GE before starting of work. (3) Guarantee: The contractor shall furnish a written guarantee for the effectiveness of the water proofing treatment for a period of Eight years in favour of the GE. A sum equivalent to 2.5% (Two point Five Percent) of the cost of water proofing treatment shall be retained by the Govt from the contractor’s dues as security deposit. The contractor may, however, furnish a fixed deposit receipt in lieu from a Schedule bank pledged in favour of Garrison Engineer.

M & L for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in roof kerb, mud stops, platform for OHT, etc., and similar type of works including weathering, slightly rounded or chamfered angles, including demolition of existing PCC of any type complete all as specified and as directed.

M & L for preparation of new plaster external wall and ceiling surfaces of and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) over and including priming coat of exterior primer applied and 1mm thick wall care putty over new surfaces complete all as specified and as directed.

M & L Preparation of newly plastered /unplastered surfaces of walls and ceilings over 1mm thick Birla White/J K White wall care putty, again sand papering thus making surface good and applying Two coats of Oil Bound Distemper on wall surfaces over a coat of primer ,complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor or in any position and paving not exc. 15 cm thick (below or above ground level) complete all as specified and as directed.

Excavation in post holes (or similar holes) in soft/loose soil each not exceeding 0.5 cum getting out, returning, filling in ramming earth or broken rubble in layers not exceeding 25 cm, watering and removing of surplus soil to a distance not exc 50m and making good surfaces, complete all as specified and as directed.

Demolition of existing RCC posts in any position complete all as specified and as directed.

Taking down barbad wire of any type in any position complete all as specified and as directed.

Supply only Chain Link MS galvanised fencing any type and size as reqd at site complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and as directed.

S&F 300mm long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

M & L for Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and as directed.

Eacavation in trenches not exc 1.5m wide and not exc 1.5m in depth for foundation exc on for walls, shafts, manholes not exc 10 Sqm on plan or for laying pipes/cables etc and getting out in soft/loose soil complete all as specified and as directed.

Returing filling in incl spreading levelling watering and well ramming in layers not exceeding 25cm in soft or loose soil complete all as specified and as directed.

Removing excavatged matereials to a distance not exc 50m and depositing where directed at a level not exc 1.5m above the starting point in soils complete all as specified and as directed.

All as per item No 29 here-in-before above but bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders complete all as specified and as directed.

M&L for RCC 1:1.5:3 Nominal Mix using 20mm graded agg as in footings, plinth beam and bases of columns complete all as specified and as directed.

M&L for RCC 1:1.5:3 Nominal Mix using 20mm graded agg as in columns , piers posts and struts complete all as specified and as directed.

S&F for Mild Steel Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed

S&F painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self tapping screws with bent to a curve (of any radius as per required) complete all as specified and as directed.

M&L for Coloured Machine pressed precast conctete interlocking paver block of any shape and size (Two colour combination) confirming to IS 15658-2006 of 60 mm thick, M-35 Grade with grey cement and pigment laid dry in floor/path over 50mm thick sand cushioning complete all as specified and as directed.

M&L for brick work in CM 1:6 using Sub class "B" bricks straight or curved on plan exc. 6mmean radius complete all as specified and as directed.

M&L for preparation of New surfaces of wall/ceiling and apply 2 coats of Exterior Acrylic Emulsion Paint (coverage area 6.5-7.5 Sqm/Ltr for two coats), over a coat of 1.5-2mm wall care putty over a coat of alkali resistent primer (coverage area 14-17 Sqm/Ltr for one coat) complete all as specified and as directed.

All as per item No 38 here-in-before above but excluding dismantling.

Taking down carefully old unserviceable copper/aluminium point wiring in conduit / batten type (light, fan, socket or power point) complete such as switches, ceiling rose, pendent holder, bell ,regulator, light fittings and socket etc and making good the disturbed surface of wall / floor/ ceiling etc as original complete all as directed.

M&L for point wiring complete with 1.5 Sq mm (nominal area) FRLS, PVC insulated un-sheathed and multistranded copper conductor cable ISI marked and including PVC concealed ISI marked of size 20 mm dia medium grade and PVC conduit fittings such as tees, bends,including FRLS, PVC insulated unsheathed 1.5 Sqmm multistranded copper earth wire, connecting to common earth dolly with and incl MS box and 3mm thick plastic laminated sheet of suitable sizes for mounting switches/sockets/fan regulator etc , and making good surface as original complete all as directed for the following :-

One light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push.

One socket outlet point 5 amps on the same board.

One socket outlet point 5 amps on the independent board.

All as per srl item No. 113 here-in-before but with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for 15 Amp light point.

S & F for switch piano, flush type single pole, one way 5 Amp complete all as directed.

S & F for switch piano, flush type single pole, one way 15 Amp complete all as directed. Make Anchor/Cona/Havells/SSK

S & F for of socket outlet 2 in 1, 3 pin, 5A, flush type complete all as directed.

S & F for of socket outlet 2 in 1, 3 pin, 5 and 15A, flush type complete all as directed.

S&F of step type Fan regulator , 120 watts, piano flush type complete all as directed.

S & F of Ceiling rose, insulated body, 3 terminal, 240 volts, etc complete all as directed.

Supply and fixing of LED mirror light fitting 10 watt, cool/warm white and making all electric connections complete all as directed.

Supply and fixing of LED tube light fitting, 20 watt. with and including all electric connections complete all as specified and as directed.

S & F of PVC in replacement ventilatiing fan 200mm sweep 230 volt AC with & including louvers and all fixing arrangements and depositing the old u/s to DGNCC store yard complete all as specified & directed.

S & F of Exhaust fan 300 mm sweep metal type, DB incuding self closing louver and making all electric connections complete and depositing the old u/s to DGNCC store yard complete all as specified and as directed .

S & F of ceiling fan 1400mm sweep, Copper winding, 240 Volts. 50 Hz and depositing the old u/s to DGNCC store yard, complete all as specified and as directed.

Supply and fixing in replacement of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 08 way, 240 volts with bus bar rating 200 Amps including dust and vermin proof and making all necessary connections complete all as directed.

Supply and fixing in replacement of Distribution Board double Door made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, surface mounting, SPN 04 way, 240 volts with bus bar rating 200 Amps including dust and vermin proof and making all necessary connections complete all as directed.

Supply and fixing in replacement of MCB C Curve type, 10 kA, 10 to 32 Amp, Single Pole with over load and short circuit protection complete all as directed.

Supply and fixing in replacement of isolator 63 Amp, SPN type with over load and short circuit protection complete all as directed.

Supply and fixing in replacement of sheet metal encloser, SPN type with two pin & earth plug and socket (Industrial type DB) with and including one MCB SP, C Curve type of capacity 20 Amp, 10 kA complete all as directed.

Material and labour in replacement for Sub main wiring with 2 run of 6 Sqmm (nominal area) FR, PVC insulated, unsheathed andmultistranded copper conductor cable ISI marked, drawn into and incl PVC conduit with all fittings and 4.0 Sqmm (nominal area) FR, PVC insulated, unsheathed and multistranded copper conductor cable ISI marked as earth wire, connected with thimble from main DB to AC point complete all as specified.

Supply and fixing in replacement of LED security light fitting 45 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as directed.

Supply and fixing in replacement of security light fitting bracket, 1 mtr long made out of galvanized iron pipe of 32 mm dia size light grade bent to shape complete with nut, bolts, washer etc inclusive of one primer coat, one under coat and one finishing coat of silver paint complete all as directed.

Supply and fixing in replacement of 2000 L SS 304 inner tank with 2mm thickness with glass wool insulation of 50mm outer, 1mm SS sheet including 6 kw heating element with thermoste with complete all as specified and as directed.

Supply and fixing in replacement of FPC collector absorber with Cu pipe, working pressure 250 kpa,cover with toughen glass, complete all as specified and asdirected.

Supply and fixing in replacement of solar EvacutedTube Collector tube of size 47/1800 mm for solar water heater, complete all as specified and as directed.

Supply and fixing in replacement Hot water GI medium grade pipe duly insulated with glass wool and aluminium cladding 25 mm bore from solar tank to FPC collector and ETC tube ,complete all as specified and asdirected.

Supply and fixing in replacement 25 mm dia gate valve for solar water heater ,complete all as specified and asdirected.

Supply and fixing in replacement of temperature gauge meter 0 to 80 degree solar water heater ,complete all as specified and asdirected.

M & L of Descaling with Eco friendly material of solar water heater tank and collector ,complete all as specified and as directed.

Supply and fixing in replacement of silicon rubber for ETC tube, open gas kit,brass open flanges,M6,M10 nut bolts for solar water heater ,complete all as specified and as directed.

Reinsulation and reinstallation of 2000 ltr SS FPC tank and making stand with MS iron angle for solar water heater tank ,complete all as specified and as directed. (Note for srl item No 134 to 142:- Old material retrieved against all items shall be deposited to DGNCC).

M/s Shubh Enterprises

M/S GEETANJALI ENTERPRISES

sunil traders

SHIV INFRA

M/s Durga Traders