PROPOSED CONSTRUCTION OF CC ROAD AND RCC DRAIN AND SABHAGRAH AND COMPOUND WALL AT PARLI VAIJNATH MUNICIPAL COUNCIL

Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading for embankment or stacking as directed.

Removing rich mix cement concrete including stacking the spoils as directed with all leads, lifts etc, complete.

Conveying materials obtained from road cutting including all lifts, lead of over 3KM. inclusive from the site of excavation to the site of deposition as directed.

Providing earth work in embankment with approved materials obtained from other sources upto lead of 50m. including all lifts, laying in layers of 20cm. to 30cm. thickness breaking clods, dressing tothe required lines, curves, grades & section, watering and compaction with vibratory roller with V-Sat attachment to achieve not less than 97% of standard proctor density etc. complete (Material obtained from Other sources)

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader/Paver on prepared surface, mixing by mixin placemet hod with rota vator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401-By Mixin Place Method and Grading-II Material

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening / binding Materials to fill up the interstices of coarse aggregate, watering and compacting with vibratory roller to the required density. By Mechanical Means- Grading II (Using Screening Type B (11.2 mm) Aggregate)

Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate (natural sand/ VSI grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor /by suitable means as approved by Engineer-in-charge, compacting with vibratory roller, finishing, curing and including preparation of suherade surface if required etc.

roviding and laying in-situ M40 Grade unreinforced plain cement concrete pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate (natural sand/ VSI grade finely washed crushed sand) conforming to 15383, using fine and coarse aggregates combined gradation as perTable 600-3 of MORTH Specification 2013, mixed in a batching and mixing plant/non tilting mixer and Weigh batcher as per approved mix design, admixtures, transporting to site, spreading, laying with approved make paver, compacted and finished in a continuous peration, finishing to lines and grades as directed by Engineer-in-charge and curingby curing compound/by providing cement vata in cement Mortar 1:[email protected] centre to centre, admeasuring 80 mm at bottom and 40 mm at top with depth of 75 mm and maintaining the same throughout curing period by any other method approved by Engineerin-charge. with fully automatic

Providing and laying 125 micron Low Density Polyethylene (LDPE) sheet confirming to IS 3395: 1997 below concrete pavement including all materials and labour complete.

Cutting transverse contraction joints 3 to 4mm wide and depth 60mm.. in concrete slab using concrete cutting machine with diamond studded saw within 48 hours of casting of bay/slab etc. complete including sub sequent widening of the groove 8 to 10mm. wide at top having depth of 15 mm. as directed by Engineer in charge.

Providing to contraction joints polysuphide sealent (Pouringgrade) confirming to BS:5212-1989 in to sawed groove wide nedat top for sealent reservoir of specified size and shape as per detailed drawing including fixing Polyethylene foam bacerrod of required diameter (appraox.25%l arger than the initial 3m One Metric Ton neo 4mm. joint) over laid with bond breaking a peasper detailed drawing. Item include scleaning the joints with water jet/air compressor and all owing join to be come thoroughly dry be for esealent is applied and applying

Providing and fixing in position TMT FE 500, 25mm dia dowel bars precoated with anticorrosive epoxy paint of required Dia. 60 cms. Long and at 30.00 cm. C/C and wherever directed including handling, straightening, necessary cutting supported by TMT FE 500, chairs with proper alignment by using properly designed assembly of Bulkheads lubricating half length with bituminous paint as directed etc. complete.

Providing and fixing in position TMT FE 500, tie bars precoated with anticorrosive epoxy paint of 12 mm dia. 70 cms.long and at 30.00 cm. C/C and wherever directed including handling, straightening wrapping with paper of approved quality for half length, necessary cutting, handling, straightening, supported by assembly of TMT FE 500, chairs with proper alignment etc. complete.

Excavation for catch/side water gutter in hard murum and boulder strata to the specified section including stacking the excavated stuff in a regular bund and disposing of unsuitable or excess stuff as directed

Providing soling using 80mm size trap metal in 15cm. Layer including filling voids with Crushed sand/grit, ramming, watering etc. Complete

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete in M20 of trap/anite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, plywood/steel formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing cast in situ / ready mix M20 grade cement concrete for head walls of CD work / retaining walls etc. including necessary form work, compaction, finishing and curing etc. complete. (with reversible drum type mixer/ concrete batch mix plant (pan mixer) with SCADA with Natural / VSI standard Artificial Sand, cement 4.05 bags/cumt)

Providing and laying in situ /ready mix M-20 cement concrete of trap/granite/quartzite /gneiss metal for approach slab /Rigid pavement including compacting, finishing, curing etc. complete. (excluding reinforcement) (with reversible drum type mixer /concrete batch mix plant (panmixer) with SCADA with fine agreegates of required specifications (VSI sand finely washed etc ), cement 6.40 bags/cumt)

Providing and fixing in position TMT - FE-500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as

Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate (natural sand/ VSI grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor /by suitable means as approved by Engineer-in-charge, compacting with vibratory roller, finishing, curing and including preparation of suherade surface if required etc.

Providing and fixing in position TMT FE 500, tie bars precoated with anticorrosive epoxy paint of 12 mm dia. 70 cms.long and at 30.00 cm. C/C and wherever directed including handling, straightening wrapping with paper of approved quality for half length, necessary cutting. handling, straightening, supported by assembly of TMT FE 500, chairs with proper alignment ett. complete.

Excavation for catch/side water gutter in all sorts of soils to the specified section including stacking the excavated stuff in a regular bund and disposing of unsuitable or excess stuff as directed all sorts of soils

Providing soling using 80mm size trap metal in 15cm. Layer including filling voids with Crushed sand/grit, ramming, watering etc. Complete

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Liftupto 3.00 m.) By Mechanical Means

Excavation for foundation in hard murum including removing the excavated material up to distance of 50 metres beyond the building area and stacking an spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc.complete. (Liftupto1.50m) By Mechanical Maane

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete.

Providing and laying Cast in situ/Ready Mix cement concrete in M20 of trap/anite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, plywood/steel formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/ granite/quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/granite/quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand /Crushed sand VSI Grade finely washed etc)

Providing and fixing in position TMTFE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete

Providing and applying two coats of water proof cement paint of approved manufacture and of approved colour to old plastered surfaces including scaffolding if necessary, cleaning and preparing the surface, watering for two days etc. complete.

Providing and applying priming coat on concrete/ masonary/Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

providing and appling two coat of flat oil paint of approved colour and shades to the plastered surface of building and workshops including scafolding if necessary cleaning the surface and preparing surface etc (excluding primer coat)

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc.

Providing and fixing H.D.P container one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet, out let overflow pipe inclusive of all tanks capacity between 200 to 1000 liters

Providing and laying in walls/ceilings/floors 25mm dia. Medium grade having embossed as ISI Mark galvanised iron pipes of 2.49 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with prime rofanti- corrosiveoil paint, 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc.complete.

Providing and laying in walls/ceilings/floors 25mm dia.medium grade having embossed as ISI Mark galvanised iron pipes of 2.49 Kilogram/ metre necessary fitting remaking good the demolished portion with filling trenches and with prime rofanti-corrosive oil paint, 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc.complete.

Providing and laying in walls/ceilings/floors 40mm dia. Medium grade having embossedas ISI Mark galvanised iron pipes of 3.68 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with prime rofanti-corrosive oil paint, 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc.complete.

Providing and laying in trenches 40mm dia. Heavy grade having embossed as ISI Mark galvanized iron pipes of 4.49Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing 15mm dia. Screw down bib/stop tap of brass including necessary socket union nut complete.

Providing and fixing 15mm dia. Screw down bib/stop tap of brass including necessary socket union nut complete.

Providing and fixing white glazed earthenware Wash Hand Basin of 55cm.x40cm. size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brasschain, stop tap and necessary pipe connections including P.V.C.waste pipe and trap up to the out side face of the wall. Making good the damaged surface, testing etc. complete.

Providing and fixing 1st class white glazed earthenware Orissa Type W.C. Pan 580 mm dia including Por S trap cast iron soil and vent pipe up to the outside face of the wall (1:5:10) cement concrete bedding 15 mm thick, 10 liter P.V.C. flushing cistern with all necessary pipe connection etc.complete.

Providing and Fixing half tum 25 mm dia gun metal flushing cock including all accessories etc. complete.

Providing and fixing 10 cm PVC nahani trap with grating etc. complete

Providing and fixing 100mm dia stabilizer pipe/ P.V.C. soil vent waste pipe and with necessary fixture sand fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete

Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7mm confirming to 1.5.13592-1992 including proper rain water receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, including fixing the pipe on wall using approved wood encleats projecting 25mm to 40mm from face of wall affixing with clips of approved quality and One Nuber, filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3yrs for any leakagesordis locations of pipes. All the P.V.C.fitting sand additional 2 piece socket clips shall be got approved from engineer incharge etc. complete

Providing and fixing 15cm x 10cm salt glazed stone ware gully trap in cement concrete 1:4:8 out side the building including cast iron grating in the sink, connecting glazed stone ware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Conveying materials obtained from road cutting including all lifts, laying in layers of 20cm to 30cm. breaking clods, dressing to the required lines, curves, grade sand section, watering and compacting to not less than 97% of standard Proctor density for aleado fover 50m. to 300m. inclusive from the site of excavation to the site of deposition as directed.3 Km lead

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/quartzite/ gneiss metal for foundation and bedding including bailing out water, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete in M20 of trap/anite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, plywood/steel formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap/granite/quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant GF

Providing and laying Cast in situ Ready Mix cement concrete M-20 of trap/granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/ pumping, compaction and rougheningthe surface if special finish is to be provided and curing etc.complete. (Excluding reinforcement and structural steel), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer)etc.complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ /Ready Mix cement concrete M-20 of trap/granite/ quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying /pumping, compaction finishing the for med surfaces with cement mortar 1:3 of sufficient minimum thickness to give as mooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible DrumType mixer/concrete Batch mix plant (Pan mixer)etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing First blass burnt brick masonry with conventional /IS type bricks in cement mortar 1:4 including scaffolding racking out joints pointing in CM 1:3 and watering in pillars of rectangular or square shape as shown on the drawing or as directed etc complete

Providing rough cast cement plaster externally in two coats to concrete, brick or stone masonry surfaces in all positions with base coat of 12 to 15mm thick in C.M.1:4 and rough cast treatment12mm thick in proportion 1:11/2:3 including scaffolding and fourteen days curing complete..

Providing internal cement plaster 20mm thick in two coats in cement mortar 1:4 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc.complete.

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete.

Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 (group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and learing etc. complete. a) Flooring

Providing and fixing steel window of various sizes as per detailed drawing without hot dip zinc coating. without ventilators, including fabricating / glazing with plain / obscured glass panels of approved type and quality, iron oxidised fixtures and fastenings, finishing with oil painting two coats complete (with guard bars 12 mm square at 10 cm c/c.)

Providing and fixing in position. (as per I.S.1868 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.1 * 1.02 mm at weight 0.547 kg/Rmt. and window frame bottom track section 61.85 * 31.75 * 1.2 mm at weight 0.695 kg/Rmt. Top and side track section 61.85 * 31.75 * 1.3 mm at weight 0.659 kg/Rmt. The shutter should be of bearing bottom 40 * 18 * 1.25 | mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 * 1.1 mm at weight 0.469 kg/Rmt. And handle section 40 * 18 * 1.25 mm at weight 0.417 kg/Rmt. and top section 40 * 18 * 1.25 mm at weight 0.417 kg/Rmt. As per detailed drawingsand as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With colour Anodising with box

Providing water proof bedding for flooring of Bath and WC 25 mm thick in C.M. 1:3 including using approved water proofing compound in specified proportion as per manufacturers specifications for per bag of cement including leveling, curing and covering 10 years guarantee on court fee stamp paper of Rs.500/-including ponding test etc. complete

Providing and fixing Country cut teak wood single leaf panelled door shutter without fanlight and 25mm thick as per drawing consisting of T.W. top rail size 100mm x 25mm and bottom lock rail 200mm x 25mm insert pannel 12 mm thick commercial ply faced T.W. particle board with phenol formaldehyde synthetic resin (Generally confirming to IS1 3097) excluding frame, including stainless steel fixture and fastening and T.W. beading to junctions of panelled inserts and as instructed by the Engineer in charge including 3 coats of oil painting etc. complete.

Providing and fixing machine cut machine polished 18mm to 20mm thick telephone black/ Amba White/ Cat bary brown/ RBI red/ Ocean Brown granite stone for treads and risers of steps and stair cases of approved colour and shade with full moulding and three grooved line for the trads on bed of 1:4 Cement mortar including float filling joint swithne at cement slurry curing polishing and cleaning etc. complete.

Providing and fixing mild steel grill gate with angle iron frame 65mmx65mmx10mm with iron bars at 150mm C/C and diagonal flats as per the detailed drawing including hinges, pivot block locking arrangement, welding riveting and oil painting of three coats of approved shade Weight of gate 35 Kilogram/Smt.

Conveying materials obtained from road cutting including all lifts, laying in layers of 20cm to 30cm. breaking clods, dressing to the required lines, curves, grade sand section, watering and compacting to not less than 97% of standard Proctor density for aleado fover 50m. to 300m. inclusive from the site of excavation to the site of deposition as directed.3 Km lead

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc.

Providing rough cast cement plaster externally in two coats to concrete, brick or stone masonry surfaces in all positions with base coat of 12 to 15mm thick in C.M.1:4 and rough cast treatment12mm thick in proportion 1:11/2:3 including scaffolding and fourteen days curing complete..

Providing and fabricating and fixing at site hot dip galavanised structural steel work in rolled sections like joists, channels, angles, tees etc.as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted I bolted I welded connections with out connecting plates, braces etc. complete including all transporation , labour and all lift excluding GST

providing and appling two coat of flat oil paint of approved colour and shades to the plastered surface of building and workshops including scafolding if necessary cleaning the surface and preparing surface etc (excluding primer coat)

Providing and applying two coats of synthetic enamel paint of approved colour to new/old structural steel work and wood work inbuildings, including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete.

Providing and applying priming coat over new/old steel and other metal surfaces including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes, fine steel wool, scrappers and sand paper, scaffolding etc. complete.

Providing and Laying factory made coloured chamfered edge Cement concrete grass paver blocks of required strength,thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine fine aggregate (natural and/crushed sand VSI grade finely washed etc.), compacting and proper embedding/laying of inter locking paver blocksinto the fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and cutting of paver blocks as per required size and pattern, finishing and sweeping extra fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and complete as per manufacturer spsecifications & direction of Engineer-in-Charge. 60mm thick CC paver block of M-35 grade concrete with approved colour and design & pattern.

Providing and fixing informatory sign boards of size 0.90 x 0.60 m made out of 14 guage Aluminum sheet bonded with IRC Specified colour of retro reflective sheeting of Type IV High Intensity Micro-Prismatic Grade Sheeting (HIP) having pressure sensitive / heat activated adhesive, IRC Specified colour retro reflective cutout border & messages having pressure sensitive adhesive having border & messages in IRC Specified colour background including on frame of with angle iron frame of size 35 x 35 x 5 mm and two M.S. angle iron post of size 65 mm X 65 mm X 6 mm, 3.65 m long, duly painted with flat oil paint having alternate black and white bands of 25 cm width including G.I. fixtures etc; fixing the boards in 1:4:8 concrete block of size 60cm X 60cm X 75cm including transportation etc;

In SSR for items of completed item rate, which are inclusive of material i.e. Rubble, Murum, Soil, 60mm./40mm. metal (Hand broken), royalty charges are not included in the basic rates. For the items of sand rates are inclusive of royalty charges. For Crush metal, the Royalty Charges are not leviable as it is manufactured product from stone and should not be considered for deductions from bills. As per Government of For Sand

For all other Minerals

TESTING Laboratory testing charges are not considered in the Rate Abstracts. Where ever required separate item shall be taken in the estimate for material testing charges, on the basis of testing frequency and charges fixed by Vigilance & Quality Compressive Strength OF C.C. Cube (Set of 3 cubes)

Concrete Mix Design I(With all Tests on basic materials)

STEEL BAR TESTING Upto 16 mm (Set of 3 Bars)

Please Enable Macros to View BoQ information