Civil and Electrical works for establishment of Cryptocurrency Tracking and Analysis Laboratory and IT Test Bed at CBI HQ Building, New Delhi

BOQ for Civil and Electrical Works for establishment of Cryptocurrency Tracking &

Analysis Laboratory and IT Test Bed.at CBI HQ Building New Delhi.

Cost of DSR Cost of Non

S NO DESCRIPTION

Items DSR Items

Digitally signed by AMIT

SCHEDULE OF QUANTITIES-CIVIL

S NO DSR-2023/ MR DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT NON-DSR AMOUNT

GYPSUM BOARD PARTITION: Providing and fixing partition upto ceiling height

consisting of G.I. frame and required board, including providing and fixing of

frame work made of special section power pressed/ roll form G.I. sheet with zinc

coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling

channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to

the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener

of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws

with nylon plugs and the studs 48mm wide having one flange of 34 mm and

other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and

ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia

bolts and nuts, including fixing of studs along both ends of partition fixed flush to

wall with suitable anchor fastener or metal screws with nylon plugs at spacing of

1 9.105 450mm centre to centre, and fixing of boards to both side of frame work by

25mm long dry wall screws on studs, floor and ceiling channels at the spacing of

300mm centre to centre. The boards are to be fixed to the frame work with joints

staggered to avoid through cracks, M.S. fixing channel of 99mm width (0.9mm

thick having two flanges of 9.5mm each) to be provided at the horizontal joints of

two boards, fixed to the studs using metal to metal flat head screws, including

jointing and finishing to a flush finish with recommended jointing compound,

jointing tape, angle beads at corners (25mmx25mmx0.5mm), joint finisher and

two coats of primer suitable for board as per manufacturer's specification and

direction of engineer in charge all complete.

75mm overall thickness partition with 12.5mm thick double skin fire rated Glass

9.105.1 Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: part 3 (Board Sqm 40 2131.10 85244

with BIS certification marks)

Providing and fixing thermal unsulation with Resin Bonded rock wool confarming

to IS:8183 having density 48kg/m3050 thick wrapped in 200 G Vergin Polythene

Bags fixed to wall with screw, rawel plug & washers and held and in position by

criss casssing GI wire etc. complete as per direction of Engineer-in-charge.

Wall painting with premium acrylic emulsion paint of interior grade, having VOC

(Volatile Organic Compound ) content less than 50 grams/ litre of approved

3 13.83 brand and manufacture, including applying additional coats wherever required to -

achieve even shade and colour.

Providing and fixing 12 mm thick frameless toughened glass door shutter of

4 21.18 approved brand and manufacture, including providing and fixing top & bottom Sqm 20 5325.90 106518

pivot & double acting hydraulic floor spring type fixing arrangement and making

necessary holes etc. for fixing required door fittings, all complete as per direction

of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Digitally signed by AMIT

S NO DSR-2023/ MR DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT NON-DSR AMOUNT

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced

Gypsum) false ceiling tiles of Size 595x595 mm o fapproved texture, design and

patterns having moisture content less than 2%, humidity resistance of 99%,

NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-

1970 and light reflectance of 85% (minimum) to be laid in true horizontal level

suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of

0.33mm thick (galvanized @ 120 grams per sqmincluding both sides) comprising

of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32

mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of

length 600mm to form grid module of size 600 x 600 mm, suspended from

5 26.26 ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e.

50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded

hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2

mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000

mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at

450 mm center to center and 40 mm long dry wall wood screws. The work shall

be carried out as per specifications, drawing and as per directions of the Engineer-

With fully perforated 12 mm thick micro tegular edged or 10 mm thick square

Providing and fixing false ceiling at all height including providing and fixing of

frame work made of special sections, power pressed from M.S. sheets and

galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277

and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of

27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling

with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of

cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts &

bolts of required size and other end of angle hanger fixed with intermediate G.I.

channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to

which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, hall

be fixed in a direction perpendicular to G.I. intermediate channel with connecting

clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction,

6 12.45 including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of

20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the

help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm

interval, including fixing of gypsum board to ceiling section and perimeter channel

with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including

jointing and finishing to a flush finish of tapered and square edges of the board

with recommended jointing compound , jointing tapes , finishing with jointing

compound in 3 layers covering upto 150 mm on both sides of joint and two coats

of primer suitable for board, all as per manufacturer's specification and

also including the cost of making openings for light fittings, grills, diffusers,

cutouts made with frame of perimeter channels suitably fixed, all complete as

12.45.3 12.5 mm thick tapered edge gypsum moisture resistant board Sqm 20 1529.10 30582.00

Digitally signed by AMIT

S NO DSR-2023/ MR DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT NON-DSR AMOUNT

Providing & fixing of 12 mm thick toughened glass partition include Complete

fitting as per instruction of Engineer In charge.

Providing and Fixing ESDH 1236-22X922 mm Dtype Handle Material : Stainless

8 MR Steel. Finish : Satin Stainless Steel (SSS). of approved make and model all Each 3 6070.25 18210.76

complete as per the direction of Engineer-in-charge.

Providing and Fixing EMB 245 SS Mortise Lock Body SB/TB for door for glass

9 MR doors of approved make and model all complete as per the direction of Engineer- Each 3 880.17 2640.522285

V BAFFLE CEILING: Providing & fixing V Baffle suspended false ceiling. profiles

of size 50/75 mm deep and 50mm / 75mm wide made with 0.5 mm thick GI,

having edges bent inwards of 4-5mm, panel length as per architect requirement,

powder coated as per approved shade. Panels shall be clipped to a GI carrier of

20mm wide x 40mm deep x 0.65mm thick black colour coated or of specified

shade, with cut outs to hold the panels with a module as specified. Panel carrier

shall be suspended by means of 4mm GI threaded rod with SS adjustable clips

10 MR holding the carrier at every 1200mm at a drop height as specified and sqm 20 5790.96 115819.12

maintaining a distance of not more than 1000mm from other carrier.The

suspension rod with clip is fixed to the slab by means of soffit cleat and rawl plug

( fastner), Gyproc® soffit cleat 27x37x25x1.6mm {GI(IS513)YS-260Mpa,Finish-

Galvanised 120GSM(IS277) } is fixed with Plug- Ø8x45mm {Material-IS 513 CR1

grade, Zinc coating (7 to 8 microns) pull out load- 6.8kN for M30 concrete grade}

GLASS FILMS: Providing & Fixing Frosted Translucent, cast PVC, self-adhesive

vinyl, special CRYSTAL-effect film to reproduce Sand-blasting effect on glass with

customised designs, thickness of 2 mil (0.05mm) without adhesive & 3mil (0.8)

with adhesive having minimum tensile strength of 3.5 pound/inch at 73 F (0.6

11 MR kg/cm at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7 Sqm 55 2056.30 113096.61

kg/cm) on Acrylic, Glass Polycarbonate: MCS warranty of 3yrs (if exposed to

direct sunlight) to 15yrs (indoors).

Providing Supply and laying LVT flooring 5 mm thickness with 0.50 wear layer (

Luxury vinyl flooring of approved design & pattern as per architects approval &

instruction). Type of flooring: Vinyl synthetic floor covering, heterogeneous with

EPT Sheild (Anti Bacterial & anti Fungal) ,SGBP Certified .Overall thickness:-

EN ISO 24346: 5.0 mm. Thickness of wear layer :- ISO 24340: 0.50- 0.55mm.

Abrasion Group: EN 660-2, Class T. Binder content wear layer : EN ISO 10582

typer I (HPD certified). Level of use - EN ISO 10874 class 23/33/42.

Dimensional stability :- ISO 23999<0.10% & Culing after exposure to heat

<1.0mm . Safety Creteria, Fire resistance EN 13501-I Bfl-s1 (Class A) Slip

resistance: EN 13893 (DS), DIN 51130-R 10 Light Fastness :- ISO 105-

B02>6 Performance Impact sound reduction :- EN ISO 10140-3 (9

dB), Resistance to Chemicals :- ISO 26987 (No Damage ) Warm water :-

under floor heating suitable max.27 C Static Load Limit : ASTM F970 <0.005in @

250psi min Formaldehyde Group :- EN 717-1 (Ei0 VOC emissions:- IAC Gold

Certified very low VOC of approved quality complete as per Architect or Engineer

Digitally signed by AMIT

S NO DSR-2023/ MR DESCRIPTION UNIT QUANTITY RATE DSR AMOUNT NON-DSR AMOUNT

PREMIUM DIGITAL GRAPHICS/DINOC WALL COVERINGS: P/F Decorative

DIGITAL GRAPHICS/DINOC as Approved by Engineer in charge on Existing

Partition and Panelling Selection as per Engineer in charge’s approval. Wall

/Ceiling Base to be prepared by applying coat of primer scrapped and

smoothened to plumb level on backing panel of Gypsum/ MDF, intermediate

13 MR grooves to be finished with Paint. Including cost of providing grooves and/Wall sq m 20 2805.80 56115.903

with divisions in pane as per Engineer in charges approval. Cost to also include

Neutral Silicon Adhesive or equivalent manufacturer suggested adhesive. Rate to

Include Wastage as per design.

Note : Area to be measured and paid for the actual installed on site.

ALUMINIUM SKIRTING:Providing & fixing of 100mm Aluminium (Grade 6063)

Skirting with 15 micron anodising In Natural Finish. Thickness 1.30 to 1.50mm.

Designed to conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers

14 MR and Gasket, all complete as per the direction of Engineer-in-charge. RM 105.00 288.27 30268.00

Digitally signed by AMIT

Supplying, installation, balancing and commissioning of factory

fabricated GSS sheet metal rectangular/ round ducting complete with

1 30.12.1 neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers,

supports, bends, transitions, reducers, end caps, collars etc as

required complete in all respect in 227 DELHI SCHEDULE OF RATES

(E&M)-2025 confirmation to IS : 655 and approved drawings and

specifications of following sheet thickness complete as required.

Supplying and fixing of following thickness duly laminated aluminium

foil of mat finish closed cell Nitrile rubber (Class "O") insulation on

2 30.23 existing duct after applying suitable adhesive for Nitrile rubber. The

joints shall be sealed with 50 mm wide and 3 mm thick self adhesive

nitrile rubber tape insulation complete as per specifications and as

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

Supplying and fixing following modular switch/ socket on the existing

1 1.24 modular plate & switch box including connections but excluding

modular plate etc. as required.

Supplying and fixing following size/module, GI box along with Modular

2 1.27 base & cover plate on existing modular metal boxes etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of

3 1.14 FRLS PVC insulated copper conductor, single core cable in surface/ recessed

medium class PVC conduit as required.

Panel Down light 2x2 ft. LED Panel light 2x2 ft., (System lumen efficacy >135

lm/Watt) Supplying of Panel light 2x2 ft., of following body material and

construction as per IS : 10322 with driver as per the requirement with Driver

efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating

temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with

Short & Open circuit protection,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR

4 (Unified Glare Rating) < 19, Flicker free, (flicker should be below 5 %), life time

(LED,Driver & electrical circuitary), of minimum 50000 Burning Hours with , 70%

of initial Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K

/6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) 135

lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required

for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as

approved by Engineer-in-Charge as per requirement. (Thermal management: heat

sink of aluminium housing such that LED junction temperature shall not rise

Digitally signed by AMIT

Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm)

Supply, Installation, Testing & Commissioning (SITC) of suspended/surface-

mounted LED Linear Light fitting, 1200mm length, 40W, extruded aluminium

5 MR housing with opal polycarbonate diffuser, system efficacy ≥100 lm/W, CCT Nos 10 4842.88 48428.79

4000K/6500K, PF ≥0.95, THD <10%, complete with LED driver, suspension

kit/mounting accessories, wiring connections, fixing hardware and all allied works

required for proper operation.

Digitally signed by AMIT

1 Reception Table

Supplying, and placing in position of reception Table . The table top made up of 36mm thick pre-

laminated particle board and understructure shall be made of 25mm thick prelaminated particle

board with 2mm thk pvc edge banding . Modesty & side panel shall be 25mm thk prelam particle

board with 2mm thk pvc edge banding . Table top height will be 750mm from the floor level &

one additional top at the height of 300 mm above the table top rest on SS stud/prelam vertical

panel . overall ht of the table 1050mm. The working edges shall be provided with machine

pressed 2mm thick PVC edging using special hot melt glue at hot temperature. Provision of

Prelam particle board Mobile pedestal of size 400mm(L)x 450mm(D)x600mm(HT) (2 drawer +

Pedestal Top made out of 18mm thick pre laminated particle board and rest all storage to be

made out of 18 mm thick prelaminated particle board . All exposed edges shall be provided with

machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. flow. The product should

be from manufacturer(OEM) which have BIFMA COMPLIENT Certification, INDIAN DESIGN MARK

Certification, GREEN PRO Certification, AIOTA Certification, BIFMA LEVEL-1 Certification, GRIHA

Certification, FSC Certification.

2 Sofa for Reception (2 seater)

Supplying and placing in position a modernist-design upholstered loral 2-seater lounge sofa with

overall dimensions of (w)1350mm x (d)870mm x (h)710mm, providing an approximate seating

area of 1120 mm (w) × 570 mm (d). The internal framework shall be constructed from 12 mm

thick, anti-termite-treated plywood (tentatively grade 303 as per indian standards for

commercial, common, and moisture-proof plywood) with a controlled moisture content of less

than 10–12% to ensure long-term structural stability and durability. The under-structure frame

shall further incorporate 12 mm thick kiln-dried german steam beech wood, selected for its

superior strength and resistance to warping, thereby enhancing the overall durability of the sofa.

The seating base is to be fitted with a high-quality web suspension system that provides resilient

support and ensures lasting seating comfort. All joints in the structure must be firmly bonded

using super bond adhesive and reinforced with star screws, wooden pins, and stapler pins to

maintain long-term joint integrity under regular usage. The sofa design features a panelled back

and cushioned armrests to promote comfortable lounging, with the entire structure padded using

high-resilience polyurethane (p.u.) foam of 32 density. The seat shall include 40 mm thick stack

foam, while the backrest and armrest cushioning shall also utilize 40 mm thick foam, all securely

fixed using adhesive super glue. The final foam assembly will be upholstered in premium yellow

54-pattern leatherette, selected for its premium feel, aesthetic appeal, and ease of maintenance.

The sofa shall be complemented by stylish sleek mild steel (ms) legs that have undergone the 11-

tank powder coating process. This premium, multi-stage metal pre-treatment includes

comprehensive cleaning, rinsing, and a crucial zinc phosphating step, which ensures the final

powder coat offers superior adhesion, exceptional durability, and maximum corrosion resistance

for a high-quality, long-lasting product. The product should be from manufacturer(OEM) which

have BIFMA COMPLIENT Certification, INDIAN DESIGN MARK Certification, GREEN PRO

Certification, AIOTA Certification, BIFMA LEVEL-1 Certification, GRIHA Certification, FSC

Digitally signed by AMIT

3 linear Workstation

Supplying, and placing in position of linear workstation as per Image.The worktop made out of

25mm thk. Prelam Particle board with 2 mm thk PVC edge banding.The Table top supported on

Mild Steel of size 50mm x50mm Slanted Leg and 50mm x 25mm Horizontal connectors with

Powder coating of 50 Micron.Middle Leg :- 0.8 mm thk Metal panel fixed on both side of the "T"

leg for Vertical wire carrying purpose.(Sharing Workstation). 0.8 mm thk Single/Double metal

powder coated raceway with Powder coating of 50 Micron below top for wiring.Vertical wire

carrying pole with powder coating 50 micron below top for wiring( Non- sharing workstation ).

Also having a provision of 0.8mm ms perfoated sheet hanging modesty. provision of 10mm thk

glass divider rest on the "D" brackets on the table top between opposite seatings. All working or

non working edges shall be provided with machine pressed 2mm thick PVC edging using special

hot melt glue at hot temperature. Also a provision of Pedestal Unit (size:- L-400mm x D-450mm

x H-600mm) with a combination of 2 drawer & one filing drawer. The pedestal storage unit shall

be made of 18 mm thick prelaminated Particle board with provision of handles & Locking

arrangement. Provision of pullout PVC keyboard tray and CPU trolley for each seating.Provision of

glass divider between two seating. The product should be from manufacturer(OEM) which have

BIFMA COMPLIENT Certification, INDIAN DESIGN MARK Certification, GREEN PRO Certification,

AIOTA Certification, BIFMA LEVEL-1 Certification, GRIHA Certification, FSC Certification.

Supplying, and placing in position of linear workstation.The worktop made out of 25mm thk.

Prelam Particle board with 2 mm thk PVC edge banding.The Table top supported on Mild Steel of

size 50mm x50mm Slanted Leg and 50mm x 25mm Horizontal connectors with Powder coating of

50 Micron.Middle Leg :- 0.8 mm thk Metal panel fixed on both side of the "T" leg for Vertical wire

carrying purpose.(Sharing Workstation). 0.8 mm thk Single/Double metal powder coated

raceway with Powder coating of 50 Micron below top for wiring.Vertical wire carrying pole with

powder coating 50 micron below top for wiring( Non- sharing workstation ). Also having a

provision of 0.8mm ms perfoated sheet hanging modesty. All working or non working edges

shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at hot

temperature. Also a provision of one Pedestal Unit (size:- L-400mm x D-450mm x H-600mm)

with a combination of 2 drawer & one filing drawer. The pedestal storage unit shall be made of

18 mm thick prelaminated Particle board with provision of handles & Locking arrangement. The

product should be from manufacturer(OEM) which have BIFMA COMPLIENT Certification, INDIAN

DESIGN MARK Certification, GREEN PRO Certification, AIOTA Certification, BIFMA LEVEL-1

Certification, GRIHA Certification, FSC Certification.

Digitally signed by AMIT

5 Manager table

Side runner Dimension:1200mm(l)x 400mm(D)x 660mm(H)

Supplying and placing in position of L-Shaped Cabin Table. Crafted with elegance from premium

materials the desk comes in 4 sizes with a polished shine. The glossy walnut finish adds value to

the desk's design. The desk table top carries a leather folio with an inbuilt wire management

system for easy access. The desk has slender curves and a stylish geometric pattern that

flowsfrom end to end. Coupled with the desk is a movable runner and pedestal in which storage

space is in abundance for stowing away your important files and folders. The table top made of

prelaminated particle board work surface with glossy walnut finish same matching edge banding

made of same matte finish. Side panel is made of 45mm thick. Provision of side runner of size is

1200mm(l)x 400mm(d)x 660mm(h), (construction is 1 openable door + 1 open shelve for cpu

back side have 3 holes ,in between both 1 key board tray with telescopic channel& 1 open box

storage (l) 550mm x (h) 350mm from down 1-drawer .2 drawers mobile pedestal of size

400mm(l)x 480mm(d)x 550mm(h) , having 2 drawers with castors in provided with central lock

for security and given curved shaped upper drawer are provided for easy of opening. Overall

construction of pedestal is 18 mm along with facia of drawers. All necessary

hardware/fitting/hinges/tower bolts/handles etc of approved quality . The product should be from

manufacturer(OEM) which have BIFMA COMPLIENT Certification, INDIAN DESIGN MARK

Certification, GREEN PRO Certification, AIOTA Certification, BIFMA LEVEL-1 Certification, GRIHA

Certification, FSC Certification.

Supplying and placing in position of a mid-back mesh revolving office chair in black colour

designed ergonomically for executive and office seating application. the overall dimensions of the

chair shall be 675mm width x 660mm depth x 1100mm height. the seat shall be made of 12mm

thick hot-pressed plywood base with moulded polyurethane foam of density 40+/-2 kg/m³,

upholstered with fabric, and supplied in black colour. the bottom of the seat should be provided

with a plastic bottom cover. the size of seat shall be 520mm width x 540mm depth. the back

should made up of pp gf and upholstered with polyester mesh fabric. this should be provided

with adjustable lumbar support to enhance ergonomics and user comfort. size of back shall be

485mm width x 570mm height. the chair shall be provided with adjustable armrests, having

polyurethane arm pads, and the arm height shall be adjustable by 60 mm to 70 mm. the chair

shall be fitted with synchro mechanism which allows the seat and backrest tilt together

ergonomically, with the backrest reclining twice the seat angle for better posture, comfort, and

reduced spinal pressure. the chair shall be equipped with pneumatic gas lift of class 4 for height

adjustment and shall be capable of sustaining a minimum user weight of 120 kg. the pedestal

shall be injection moulded in black made of glass filled nylon with 5 nos. high impact

thermoplastics twin-wheel castors, each with a minimum diameter of 55 mm, and shall be

supported on five castors for stability and easy mobility. the pitch-centre-dia of the pedestal

should be 660mm. The product should be from manufacturer(OEM) which have BIFMA

COMPLIENT Certification, INDIAN DESIGN MARK Certification, GREEN PRO Certification, AIOTA

Certification, BIFMA LEVEL-1 Certification, GRIHA Certification, FSC Certification.

Digitally signed by AMIT

Supplying and placing in position of a high back mesh revolving office chair in black colour

designed ergonomically for executive and office seating application. The overall dimensions of the

chair shall be 675mm width x 660mm depth x 1300mm height. The seat shall be made of 12mm

thick hot-pressed plywood base with moulded polyurethane foam of density 40+/-2 kg/m³,

upholstered with fabric, and supplied in black colour. The bottom of the seat should be provided

with a plastic bottom cover. The size of seat shall be 520mm width x 540mm depth.

The back should made up of pp gf and upholstered with polyester mesh fabric. This should be

provided with adjustable lumbar support to enhance ergonomics and user comfort. Size of back

shall be 485mm width x 790mm height. The chair shall be provided with adjustable armrests,

having polyurethane arm pads, and the arm height shall be adjustable by 60 mm to 70 mm. The

chair shall be fitted with synchro mechanism which allows the seat and backrest tilt together

ergonomically, with the backrest reclining twice the seat angle for better posture, comfort, and

reduced spinal pressure. The chair shall be equipped with pneumatic gas lift of class 4 for height

adjustment and shall be capable of sustaining a minimum user weight of 120 kg. The pedestal

shall be injection moulded in black made of glass filled nylon with 5 nos. High impact

thermoplastics twin-wheel castors, each with a minimum diameter of 55 mm, and shall be

supported on five castors for stability and easy mobility. The pitch-centre-dia of the pedestal

should be 660mm.The product should be from manufacturer(OEM) which have BIFMA

COMPLIENT Certification, INDIAN DESIGN MARK Certification, GREEN PRO Certification, AIOTA

Certification, BIFMA LEVEL-1 Certification, GRIHA Certification, FSC Certification.

Digitally signed by AMIT

8 Storage -1

Supplying, and placing in position of full height storage @ 1800mm height as per

photograph/drawing . The storage unit having Openable shutters with shelf in it. The modular

storage unit top shall be made from 18 mm thick pre-laminated particle board and rest of the

sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board

while back to be made of 8 mm thick pre-laminated particle board. All edges to be provided with

2 mm thick PVC lipping. The storage unit having openable shutters with D shape handles &

locking arrangement..The product should be from manufacturer(OEM) which have BIFMA

COMPLIENT Certification, INDIAN DESIGN MARK Certification, GREEN PRO Certification, AIOTA

Certification, BIFMA LEVEL-1 Certification, GRIHA Certification, FSC Certification.

9 Storage -2

Supplying, and placing in position of full height storage @ 1800mm height as per

photograph/drawing . The storage unit having Openable shutters with shelf in it. The modular

storage unit top shall be made from 18 mm thick pre-laminated particle board and rest of the

sides as well as shelves and shutter to be made up of 18 mm thick pre-laminated particle board

while back to be made of 8 mm thick pre-laminated particle board. All edges to be provided with

2 mm thick PVC lipping. The storage unit having openable shutters with D shape handles &

locking arrangement..The product should be from manufacturer(OEM) which have BIFMA

COMPLIENT Certification, INDIAN DESIGN MARK Certification, GREEN PRO Certification, AIOTA

Certification, BIFMA LEVEL-1 Certification, GRIHA Certification, FSC Certification.

10 Centre Table

Supplying and placing in position of centre table of size:(W) 820mm X (D) 820mm X (H) 410mm

as per image. Gentle curves meet grounded strength in our sculptural Featuring the graceful arc

of a solid wood base and round marble-effect laminated top, this coffee table is all about balance.

Base crafted from kiln-dried solid wood in Walnut finish.Round tabletop features a premium

laminate with a marble-inspired finish.The warm walnut finish contrasts beautifully with soothing,

off-white hue Gently curved design adds visual rhythm.Buffers ensure smooth, easy mobility

while protecting floors from scratches. Material & Subtype:Solid Wood - Steam Beech Wood,

Base Material:Solid Wood, Colour & Colour Family:White - Off, Brown - Walnut, Dimension:(W)

820mm X (D) 820mm X (H) 410mm,Table Top Thickness:18mm. .The product should be from

manufacturer(OEM) which have BIFMA COMPLIENT Certification, INDIAN DESIGN MARK

Certification, GREEN PRO Certification, AIOTA Certification, BIFMA LEVEL-1 Certification, GRIHA

Certification, FSC Certification.

Digitally signed by AMIT