SPL REPAIRS TO SIX TOILET BLOCKS AT BLDG NO P-581 CHILDREN SCHOOL (3 X BOYS AND 3 X GIRLS TOILET) UNDER ZONE-I AREA AT JAIPUR MIL

Amount

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15 deep and getting out in soils.

Excavating in trenches , n exc 1.5 m wide and n exc 1.5 m depth for foundation etc. Or for shafts , wells manholes, pier holes etc. N exc 10 sqm on plan and n exc 1.5 m in depth and getting out hard/dense soil.

M&L Returning, filling in,including spreading, levelling , watering and well ramming in layers not exc 25 cm.

Demolition of PCC in ground floors and pavings n exc 15 cm thickness (below ground level) all as directed.

Demolition of precast RCC jallies incl framing of any description and in any position set in cement mortar

Demolition stone slabs and tiles of any description or thickness in floors, aprons etc laid,bedded and pointed in cement mortar

Removing excavated material n exc 50 m and deposited where directed at a level n exc 1.5 m above the starting point.

M&L for PCC 1:4:8 type D2 in foundations, fillings and mass-concrete, sub base of floor

M&L 150mm thick cement concrete type D-2,1:4:8(40 mm graded aggregate) in subbase, floors and paving etc all as directed.

M&L 75mm thick PCC (1:4:8) type D-2 using 40mm graded stone aggregates in sub base complete

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

Demolition of brick work or stone boulder masonry built in cement mortar complete all as directed

Taking down cement plaster on brick/stone wall, ceiling etc including raking outs joints hacking for key scrubbing with water all as directed.

Taking down door chowkaht or frame of any description area n exc 1.50 Sqm each without taking off shutters from the frame.

M&L for brick work with sub-class 'B' bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as directed

M & L Brick work with sub-class `B' bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as directed

M & L Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in 1:6 cement mortar

M & L Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in 1:6 cement mortar except stone.

Supply and fixing anodised aluminium window and ventilator shutters, side hung type without sash, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium fittings such as peg stays 150mm long 1 No, hinges type B-21, 100mm long (2 No) suitable handle 1 No complete

S & F Stainless steel wire cloth 0.36 mm nominal dia of wire & average width of aperture 1.40 mm and fixed with stainless steel wire staples

S & F 5.5mm thick plain sheet glass ordinary quality to aluminium door/ window in sqaures not exc 0.5 sqm in each pane complete

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube as per specification and drawing.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. Tubes for top & bottom rails, MS frame shall be covered with heat moulded lain colour PVC Ç'channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading and jointed together with solvent cement, suppling and fixing in the frame at site as per secification & drawing.

S&F stainless steel Butt hinges, medium weight and fixed 100 mm size.

S&F 150 mm long Aluminium anodised barrel tower bolt of extruded section complete all as directed

S&F aluminium handles cast type anodised 150 mm size complete all as specified

M& L Rendering 10 mm thick cement plaster in CM 1:6 on fair faces of brick work (Internal Surface) including finished even and smooth without using extra cement

M&L Rendering 15 mm thick cement plaster in CM 1:4 on other fair faces on brick masonry (External surface) including finished even and fair without using extra cement.

M&L Rendering 10 mm thick cement plaster in CM 1:3 on ceiling surface finished even and smooth without using extra cement.

Taking up or down steel tubing and connection including cleaning 15 mm bore

Taking up or down steel tubing and connection including cleaning 20 mm bore

Taking up or down steel tubing and connection including cleaning 25 mm bore

S&F GI tubing medium grade with all fitting 15 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor.

S&F GI tubing medium grade with all fitting 20 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor.

S&F GI tubing medium grade with all fitting 25 mm bore fixed to wall or concealed or fitted to ceiling or laid under floor.

S&F as in repair 15 mm bore bib cock, two way, cast copper alloy chromium plated, fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule complete all as directed. Make : CERA Cat No F2007161 or equivalent as approved by GE.

S & F in repairs 15mm bore Concussive push button taps of cast copper alloy, screwed for iron pipe and fixed down for iron pipe and fixed complete. Make - Marc, Parko, GEM or equivalent as approved by GE

S&F as in repair cromium plated brass hand shower (health faucet) with 8mm dia 1.00m long flexible tube and wall hook complete all as directed. Make : CERA Cat No F8030401AB or equivalent as approved by GE

S&F as in repair cromium plated brass soap dispenser automatic capacity 0.8L of aluminium/ABS materials crome/black finish complete. Make : CERA/PRAYAG/JAQUAR or equivalent as approved by GE

S&F as in repair Hand dryer stainless steel of stain finish complete. Make : CERA/PRAYAG/JAQUAR or equivalent as approved by GE

S&F in repair Toilet paper roll holder with flap Vitreous china with CP brass screw. Make : CERA Cat No F5002110 or equivalent as approved by GE

S&F in repair soap dish, vitreous china white, approx size 160x160x90 mm. Make : CERA Cat No F5003106 or equivalent as approved by GE

S&F PVC connections 15 mm size with PTMT nuts of length 600 mm.

S & F in repair vitreous china wash basin, snow white 0f 520 mm diasize fixing in granite excluding taps, waste chain and plug and porcelain stopper but including CP coupling , PVC waste pipe complete. Make : CERA cat No S2030138 or equivalent as approved by GE.

S&F as in repair bottle trap of PTMT 32mm bore with 300mm long wall connection pipes with minimum weight 32 mm- 260 gms.

S & F in repair 15 mm bore Pillar cock with swan neck spout and aerator complete all as specified and directed Make : CERA cat No F20007104 or equivalent as approved by GE.

S&F in repair vitreous china Pedestal pattern EWC S trap white bowl size 655mm x370mm x730 mm including cistern complete all as specified and directed Make : CERA Cat No S1013124 or equivalent as approved by GE.

S&F in repair vitreous China urinals, half stall long body type(back or corner wall type) of size 375x390x590mm complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, Make : CERA Cat No S4020112 or equivalent as approved by GE

S&F in repair stop valve cast copper alloy, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe 20 mm bore or union and fixed

S&F in repair stop valve cast copper alloy, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe 15 mm bore or union and fixed

S&F in repair angle stop valve cast copper alloy chromium plated screwed for iron pipe 15 mm bore. Make : CERA Cat No F2007201 or equivalent as approved by GE

S&F in repair ball valve high pressure of PTMT with epoxy coated aluminium rod &high density plastic bal screwed for iron pipe 20 mm dia and fixed (Minimum Weight 210 gms) complete all as directed

S&F in repair 100 mm bore Cast iron soil, waste and vent pipe in any length with or without ears, with cement Joints, laid in trenches or but fixed in walls

S&F Bends for 100 mm bore pipe with ducks foot or heel rest for cast iron pipe fitting

S&F cast iron cowls for 100 bore pipe

S & F for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165

S&F cast iron floor traps with grating including jointing to waste pipe fixed in cement concrete type B-1(1:2:4) for 100 mm bore pipe complete all as directed

S&F Branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval asses door for 100 mm bore cast iron pipe fitting

Dismantling water tank of capacity Exc 500 & n exc 1000 ltr , and removing to store complete all as directed

S&F Rotatinal moulded polyethylene water storage tanks (double layer) (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I capacity 1000 ltr

S&F Brass chromium plated tubular towel rail 20 mm dia D type 60 cm long between flanges. Make : CERA Cat No F5004103 or equivalent as approved by GE

S&F Looking mirror 5mm thick bevelled edge , size 0.75M x 2.5M fitted with distance pieces( 4Nos ) of stainless steel including making holes in mirror, fixing arrangement as directed

M&L preparation of newly plastered surface wall and applying two coats of distemper oil emulsion of any tint over a coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment of old external plastered surface of walls and applying priming ( Seal- o - Prime) on plastered surface and two coat of weather proof exterior emulsion paint (Weather coat smooth) complete all as specified and directed.

M&L for two coat of weather proof exterior emulsion paint (Weather coat smooth) over a coat of priming ( Seal- o - Prime) on new plastered surface complete all as specified and directed.

M & L preparing new plastered surfaces and applying two coats of cement base paint on wall

M&L preparation of newly plastered surface wall and applying two coats of cement base paint of any tint over a coat of primer complete all as specified and directed.

M&L preparation of newly plastered surface on ceiling and applying two coats of distemper oil emulsion of any tint over a coat of primer complete all as specified and directed.

M&L for preparation of new concrete surfaces of any description over 10cm girth or width, not otherwise described and applying two coat of synthetic enamel paint over a coat of primer complete all as specified.

Forming construction joints 30mm deep x 10mm wide filled with sealing compound Grade 'A'. complete all as specified and directed.

Dismentaling of floor hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish of the premises.

M&L 25 mm Thick PCC 1:2:4 type B0 under floor tiles

M&L 40mm thick PCC (1:2:4) type B-0 as in DPC to horizontal or vertical surfaces including necessary formwork.

M & L precast cement concrete louvers and jallies type B-0 mix 1:2:4 (using 12.5mm graded stone aggregates) for 30mm thick (measured solid) including all mouldings but excluding frame set in CM 1:4

M&L 200 mm thick cement concrete type B-2, 1:2:4(40 mm graded aggregate) in subbase, floors and paving etc all as directed.

M&L Non skid coloured joint free ceramic tiles 7mm to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm as in floor set and jointed in neat cement slurry and pointed in coloured cement match the shade of tiles over and including 15 mm thick screed bed in CM 1:6 complete all as directed

M & L glazed coloured joint free ceramic tiles 300x600x7 to 8 mm thick, on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick backing coat on surfaces other than fair faces of brick work in CM 1:4 complete all as directed

M&L reinforcement cement concrete (Design mix) type A1, 1:11/2:3 (20mm graded aggregate) as in slab support on walls, landing, balconies, deck slabs and in shelves and the like all as specified (demolition to be taken)

Demolition of reinforced cement concrete in steps and similar suspended works

M&L precast reinforced cement concrete (Nominal mix) 1:2:4 type B-1 using 20mm graded stone agg for manhole cover slab set in cement mortar 1:6 incl necessary form work. Note :- Reinforcement shall be paid for separately.

M & L providing precast cement concrete type B-1 mix 1:2:4 (using 20mm graded stone aggregate) in posts, brackets, copings etc with plain fair faces, including chamfers, weatherings, throatings etc and setting in CM 1:4

S & F Engraved Granite stone name plate 20 mm thick (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

M&L formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n.exc 20cm wide for rough finished surfaces all as specified and directed.

M&L for Granite (of any tpe), 16 to 18mm mm work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M&L moulding to granite stone 16 to 18 mm round complete including polishing complete all as directed.

Taking down carefully aluminium/copper point wiring (light fan socket or power) complete with fitting such as switches, tube lights, ceiling rose, pendants, regulators, and making good disturbed surfaces of walls, floor to match with existing specification complete and all as specified keeping aside regulators/ light fitting complete.

M& L for point wiring with 1100 volts grade PVC insulated FRLS multistranderd copper conductor cable 1.5 sq mm ( Phase - Red , Neutral - Black) and earth continuity conductor 1.5 sq mm (green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less then 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and galvanized pressed steel terminal boxes and including modular metal flush boxes 1.0 mm thick for mounting switches sockets, fan regulator as required for one light point controlled by one switch .

All as per item No. 90 above but One fan point controlled by one switch.

All as per item No. 90 above but One socket outlet 6 amp controlled by one switch on the same board with other switches.

S&F switch piano flush button single pole one way 6 amp complete

S&F socket outlet 2 in 1, 2 & 3 pin, 6 amp, flush type complete.

S&F ceiling rose 3 plates polycarbonate body complete.

M &L for sub main wiring along with earth continuity conductor with PVC insulated FRLS multistranded copper conductor cable (Phase- Red , Neutral- Black Earth - Green ) drawing into and including concealed rigid non metallic PVC conduit, medium grade ISI marked ivory colour along with accessories of size 2x 2.5 Sq mm + 1x2.5 sqmm earth wire in 20 mm dia of conduit

M&L for sand cushioning locally available in trenches for cushioning of LT UG cable 8 cm below cable & 15 cm above cable gently punned down to a depth of 10 Cm above the top of the cable complete.

M&L sub class 'B' brick covering protection to the electric cable laid dry flat transversally along the length of cable on sand cushioning with width equal to length of brick complete.

Supply and fixing LED flood light 70 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp.

S&F 1100 volt grade heavy duty XLPE cable with PVC insulated aluminium conductor served with inner sheathing of PVC tape armoured with galvanized steel strip or wire and overall PVC sheathed of size 10 sqmm nominal cross section 2 core laid in trenches, fixed to pole or passing through pipes including all necessary clamps, nuts, bolts washers complete all as specified and directed.

S&F and installed LT Panel out door type of CRCA sheet 3.15m thick not less then 0.3x0.3x0.25 mtr including suitable size angle iron lags and cement work complete incoming 40 Amps DP MCB - 01 Nos and outgoing 20 Amps SP MCB -02 Nos complete all as specified and directed by Engr-in-charge.

Taking down MCB distribution boards with incoming and out going controls ,any make ,any size

Taking down carefully sub main wiring with PVC casing capping / PVC surface conduit and making good surface complete.

Supply and fixing LED lights fitting 1x 20 W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

S&F MCB distribution board, powder coated, CRCA steel sheet, degree of protection IP 43, IK-09 with reversible double door, recess mounted , having insulated 100 Amps tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required with SPN, 240 volts, 8 ways.

S & F MCBs of 'C' series having breaking capacity 10 KA ISI marked including required wiring connection with copper lugs of suitable size provided in MCB DBs of Single pole 6 to 32 Amps

All as per item no. 107 above but Double pole 10 to 32 Amps

Supply and fix exhaust fan made of steel complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm

Schedule of Credit

NAGHAR ENTERPRISES

S.R.Enterprises

NARAYAN SINGH NARENDRA SINGH AND COMPANY

ABHI CONSTRUCTIONS

M/s Jai Jinendra Constructions

UNIVERSAL INFRAPROJECT PVT LTD

M/S Mohan Lal Gupta