Construction of Anganwadi Building at Kizhveeranam village H/O Kizhveeranam Panchayat

Amount

Construction of Anganwadi Building at Kizhveeranam village H/O Kizhveeranam Panchayat

Earth work excavation for foundation in all classes of soils and sub soil to full depth except in hard rock requiring blasting but inclusive of shoring strutting if required for the sides of foundation.

Collection and supply of gritty gravel including cost and conveyance of all charges etc

Cement Concrete 1:4:8 mix using 40mm metal including cost and conveyanceof all materials to work site and all labour charges etc.

Brick work in C.M 1:5 mix using country bricks incuding cost and conveyance and all labour charges etc. Up to Basement

Above Basement

Reinforced cement concrete 1:1.5:3 mix using 21mm ISS metal including cost and conveyance of all materials to site and all labour charges for mixing, laying, and curing etc complete (sunshade) Column Below

Column Above

Supplying and errecting for sides & soffits including supports and strutting upto 3.29m height for plane surface in all floors including cost and conveyance and all labour charges etc. Below GL

Above GL

Supply and fabrication of steel including cost and conveyance and all labour charges etc. complete.

Providing granolithic floor finish in cement concrete 1:2:4 mix using 10-12mm ISS metal to 25mm thick including cost and conveyance of all materials to site and all labour charges for mixing, laying, curing etc complete for 10 cum 40mm Thick

Finishing the top of roof with one course of Solar Reflective ceramic tiles (Required design) of size 305x305x25 mm thick of approved quality and colour laid in CM 1:3, 12mm thick and pointed with tile grout(Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint,curing etc., complete complying with satandard apecification and as directed by the department officers.(The make and brand of the tiles should be got approved by the Executive Engineer before use on works) PWD Data (observed)

Plastering with cement mortar 1:5, 12mm thick including cost and conveyance and all labour charges etc.

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The Surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers. [ The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (waterproof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coat of putty, scrapping the putty area to level the surface smooth, etc., complete). The Putty shoule be got approved by the Executive Engineer before use on work

Ceiling Plastering with cement mortar 1:3 mix to 10 mm thick for R.C.C. Items including cost and conveyance of all materials to site and all labour charges etc complete

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three M.Sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone M.Sand) 20mm thick and pointed with white cement mixed with

Dadooing the sides of the wall up to the required height and approved quality colour printed Glazed tiles of size 305 x 200 x 3 mmand set in CM 1 : 2,10mm thick and pointing with same colour cement of 4kg including cost and conveyance of all materials and

Towards the cost of steel door of size 0.90mx2.40 m including all charges etc.

Towards the cost of steel door of size 0.75mx1.50 m including all charges etc.

Towards the cost of steel door of size 1.10mx2.40 m including all charges etc.

Towards the cost of steel ventilator of size 0.9x0.45 m including all charges etc.

Towards the cost of steel Window of size 1.20x1.30m including all charges etc.

Towards the cost and fixing of RCC Jolly of size 0.90x0.45m including all charges etc.

Painting two coat with approved quality of oil bound distemper with colour over one coat of white cement for primier coat for the base including preparing surface and all materials cost labour etc

Painting two coat with ready mixed plastic emulsion of first quality paint and of approved colour over a priming coat including thorogh scarpping clean removal of dirt etc complete.

Painting two coats using Ist quality readymix enamel paint of approved colour including cost and conveyance and all labour charges etc.

LIGHT POINT SD 20

FAN POINT SD 20

Plug point (SD38)

Ceiling Fan

TNHB meter

7/20 GI Bearer wire

EB deposit

32Amps DP switch

GI Pipe

Bulk head fitting (SD83)

Copper coke

1000 lit tank

Cost & Supply For Baby W.C including cost and conveyance of all materials to work site and labor charges etc complete.

Cost & Supply For E W.C including cost and conveyance of all materials to work site and labor charges etc complete.

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pilla

Cost & Supply of Cudappah Slab including cost and conveyance of all materials to work site and labor charges etc complete.

Providing and fixing PVC Rain water down fall pipes of 100mm dia with necessary shoes bends and other specials clamps screws nails teakwood plugs etc

GST Amount for providing Service to Government Contract Works for the above Construction & Maintenance Works. { GST Amount is the Total GST Amount for overall quoted amount (Both Construction and Maintenance) above this row in column "BB" for all works in this package} (Refer Clause 13.2 & 13.3 of Section 2 of Instruction to Bidders (ITB) of SBD)

N.Dhinakaran (BID ID -1297035)