REPAIR REPLACEMENT OF EXTERNAL WATER SUPPLY DISTRIBUTION LINE AND REPAIR TO DG SET AND OTHER MISC WORKS FOR DGQA AREA UNDER GE (I) KANPUR.

Amount

Excavation in trenches not exceeding 1.5 mtr in depth and not exceeding 1.5 mtr wide in any type of soil for laying and taking out of GI/CI pipes all as specified and directed.

Returning filling in including spreading, leveling watering and well ramming in layers not exceeding 25cm thick complete all as directed.

Removing excavated soils to a distance not exceeding 50 m and depositing where directed.

M&L for drilling hole at a depth up to 1.5 mtr below the normal ground level of suitable size to insert upto 150 mm dia pipe across the road in horizontal position complete all as directed.

M&L for cutting of road depth up to 1.5 mtr below the normal ground level of suitable size to lay pipe upto 150 mm dia pipe across the road in horizontal position incl making good all disturbed surfaces of road to match with existing surfaces by premix road material/PCC complete all as directed.

Disconnecting, dismantling and taking up or down old/unserviceable/cracked GI tubing with fittings of size 15 mm bore incl cleaning for refixing complete all as spfd and directed. Note: Excavation and earth work will be measured and paid separately under relevant items.

All as per Srl No 6 above but of size 20mm.

All as per Srl No 6 above but of size 25mm.

All as per Srl No 6 above but of size 40mm.

All as per Srl No 6 above but of size 50mm.

All as per Srl No 6 above but of size 80mm.

Re-laying, jointing and testing old but serviceable GI tubing 15mm dia (obtained from srl item No-6) and connection in new or old portion incl new fittings such as bends, elbows, union, tees, reducers etc as required at site laid in trenches or on floor or wall complete and making good all disturbed surfaces of wall/ floor/ road/ path to match with existing specification all as specified and as directed.

All as per Srl No 12 above but of size 20mm (obtained from srl item No-7).

All as per Srl No 12 above but of size 25mm (obtained from srl item No-8).

All as per Srl No 12 above but of size 40mm (obtained from srl item No-9).

All as per Srl No 12 above but of size 50mm (obtained from srl item No-10).

All as per Srl No 12 above but of size 80mm (obtained from srl item No-11).

Supply & Laying, jointing and leakage testing GI tubing medium grade 15mm bore with all fittings such as bend, tee, elbow, union, reducer etc, laid in trenches/floor/walls and making good the disturbed surface to match with existing surface as (PCC work in 1:2:4 using 20 mm graded stone aggregate/ plastering in CM 1:4 and applying finishing coat of existing treatment) complete all as specified and as directed at site. Make: Tata/Jindal/Prakash Surya. Notes :(i) The laying and jointing of pipes are required to be carried out in short / long streches catering to specific requirements of a purticular quarter or a group of blocks. (ii) Excavation & earth work shall be measured & paid seperately.

All as per Srl No 18 above but of size 20mm.

All as per Srl No 18 above but of size 25mm.

All as per Srl No 18 above but of size 40mm.

All as per Srl No 18 above but of size 50mm.

All as per Srl No 18 above but of size 80mm.

Disconnecting, dismaantling and taking down CI/GI/DI/Cemented pipe line of size 100mm bore, including all fittings with spigot and socket/ flanged end or any type, lead joint including removing from site complete all as specified and directed.

Re-laying, jointing and testing old but serviceable CI/DI pipe line of size 100mm bore after cleaning as taken down under Srl item No 24 here-in-before including all fittings as required at site complete and making good all disturbed surfaces of wall/ floor/ road/ path to match with existing specification all as specified and directed.

Supply fixing and testing DI pipe line of size 100mm bore, including all fittings with spigot and socket/ flanged end or any type, lead joint including removing from site complete all as specified and directed.

S&F in replacement of cast iron double flanged sluice valve of size 80mm bore class PN 1.0 confirming to IS 14846/2000 with with high tensile stainless steel spindle with CI wheel, Gun Metal Nuts/rings 'I' bolt, ISI marked including replacement of rubber packing complete all as specified and directed. Make : Kirloskar/Upadhyay.

All as per Srl No 27 but sluice valve of size 100mm.

M & L for boring on existing CI pipe upto 200 mm dia for branch connections of up to 50mm dia pipe by fixing of MS clamp 50x4mm cut to length and bent to shape, drilled and welded with GI socket of suitable size incl rubber packing, nut, bolt etc and testing complete all as specified and direted.

Repair to GI pipe lines of size 15mm to 25 mm bore dia and repair to leaked joints of pipe line complete including replacement of old GI fitting i.e union,nipple & sockets etc including excvation and taking up & down GI pipe required cutting & threading refixing in position in trenches and making good all disturbed surfaces of wall/ floor/ road/ path to match with existing specification all as specified and as directed. Note: Excavation and earthwork shall be measured and paid separately under respective items

Repair to GI pipe lines of size 40mm to 80 mm bore bore dia and repair to leaked joints of pipe line complete including replacement of old GI fitting i.e union,nipple & sockets etc including excvation and taking up & down GI pipe required cutting & threading refixing in position in trenches and making good all disturbed surfaces of wall/ floor/ road/ path to match with existing specification all as specified and as directed. Note: Excavation and earthwork shall be measured and paid separately under respective items

Cutting existing CI/DI water main 150mm bore pipe in position for making branch connection and CI/DI pipeline (Insertion of CI/DI tees bends of different size on connection pieces or for insertion of sluice valve) including excavation & earth work. Note : Fittings such as tees, bends, collars & reducers etc incl in this item and only run lead joints, CI/DI fittings & sluice valve shall be measured and paid separately and making good all disturbed surfaces of wall/ floor/ road/ path to match with existing specification all as specified and as directed.

All as per srl No 32 but of size 100 mm.

All as per srl No 32 but of size 80mm.

M&L for Run lead joints complete with spun yarn of size 80mm dia all as spfd and directed.

All as per srl No 35 but of size 100 mm.

All as per srl No 35 but of size 150 mm.

M&L for Cast iron/ductile iron special fittings for spigot and socketed pipes such as bends (any type, radius and angle) socket tapers any type, (straight, bend, increasing, decreasing or double socket etc) Tee pieces, single branch, Y junction, double branch, cross (all sockets or socket and spigot) collers, caps and plugs for upto 150 mm bore pipes complete all as specified and directed.

S & F in replacement of stop valve 20mm dia, gun metal iron, screwed down, high pressure with crutch or butterfly handle, screwed for iron pipe or for ferrule ISI marked including dismantling the old U/S existing valve complete.

M & L for opening up of leaking sluice valve 80mm and repacking of stuffing box & replacement of gland packing, nuts, bolts & washers etc complete all as specified of the following sizes :-

All as per item No-40 but of size 100 mm dia.

All as per item No-40 but of size 150 mm dia.

S & F in replacement of gun metal iron gate valve 25mm dia with iron wheel head, screwed both ends for iron pipe, ISI marked, complete all as specified including dismantling the old unserviceable existing valve complete.

All as per srl item 43 but of size 40 mm bore.

All as per srl item 43 but of size 50 mm bore.

M&L joints with rubber gaskets for CI flanged pipe including necessary nut bolts and washers etc for pipe 80 mm bore all as specified.

All as per srl item 46 but of size 100mm bore.

All as per srl item 46 but of size 150mm bore.

S&F replacement stainless steel spindle with checknut suitable for sluice valve of size 80mm bore including replacment of gland packing all as directed make : BIR/VENUS/MINAR

All as per srl item 49 but of size 100mm bore.

All as per srl item 49 but of size 150mm bore.

Cutting and removing unwanted grass and wild growth including bushes and shrubs from the roots at water supply installations including removing and even finish the entire area complete all as specified and directed at site by Engineer in charge.

Supply only sodium based granular having chlorine content 60-70 % disinfectant for water treatment, more stable than Chlorine Gas, and stronger than bleachingpowder, and sodium Hypochlorite packing in 45 kg drum completed all as specified & directed. Make : Declibac/Brizing/Aquafit or E-in-Cs approved (Note: Contractor must produced TC & PVS from the manufactures/ All India Distributor at the time of supply for the Originality of material).

M & L for construction of valve pit chamber in replacement 600 x 600 x 950 mm internal dimensions, 6 mm thick MS sheet cover with 2 Nos MS hinges welded to angle iron frame of 40x40x6 mm thick with lifting hook and locking arrangement complete with necessary earth work, brick work in CM (1:6), 230 mm thick, PCC bed (1:4:8) type D2 150 mm thick, cement plastering, finishing 15 mm thick in CM (1:4) and applying a coat of black bituminous paint to the steel surfaces incl dismantling and removal of old unserviceble valve pit remains all as specified and directed.

M & L for construction of valve pit chamber in replacement 950 x 950 x 950 mm internal dimensions, 6 mm thick MS sheet cover with 2 Nos MS hinges welded to angle iron frame of 40x40x6 mm thick with lifting hook and locking arrangement complete with necessary earth work, brick work in CM (1:6), 230 mm thick, PCC bed (1:4:8) type D2 150 mm thick, cement plastering, finishing 15 mm thick in CM (1:4) and applying a coat of black bituminous paint to the steel surfaces including dismantling and removal of old unserviceble valve pit remains all as specified and directed.

S & F in replacement of fully automatic star delta starter, suitable for up to 30 HP submersible motor, 3 phase 440 volt complete with over load protection with adjustable relay range, electronic timer relay and single phasing preventor incl suitable size 40X4 mm angle iron frame grouted on wall for proper mounting arrangement all as specified. Make : SEIMENS / BCH / L & T

M&L for replacement of MS angle iron/Channel support for motor/pump incl nut bolt etc incl painting and making good all disturbed surfaces with PCC 1:2:4 complete all as spfd and directed.

Cleaning/removal of grass/bushes/plants/mud etc all around/inside the valve pit chamber up to size 950mm x 950mm x 950mm complete all as spd and directed all as specified and directed.

Taking up/down pipe line including excavation, returning filling and removal of excavated soil near existing pipe line of size 80 mm bore in break down maint of rising main line/distribution line. Providing any type of special tools & plants such as JCB & material (such as detachable joints/leak repair clamp suitable for CI/DI fittings, coller/short pieces of pipes or any other fittings as required to minimize the breakdown time and rectification of the problem as soon as possible. Rectification work must be start within two hours of intimation to contractor. Any delay in rectification may be penalized as deemed fit.

All as per item No 59 above but 100 mm dia bore

All as per item No 59 above but 150 mm dia bore. Note: for item 58 to 60: Excavation and earthwork if any shall be measured and paid separately under respective items.

M&L for repairing the leakage of flange end joints for MS/CI pipe by doing welding incl replacement of rubber gasket, nut, bolt and washers etc bailing out pipe line water as required and directed for the sizes 150mm bore.

Taking / lifting out defective submersible pumps set from bore well complete with column pipe upto 150mm dia steel rope, submersible cable and accessories etc and relowering and commissioning the same after repairing works and testing complete of rating 20 to 30 HP 3 phase.

Dismantling, taking out complete burnt winding wire of submersible motor including cleaning of stator slots replacement of defective parts and rewinding with existing type & gauge of copper winding wire pvc insulated as per motor capacity and using new insulation material such as insulating paper sleeves etc.replacement of submersible cable as required size/ length complete incl testing all as directed of rating 5hp to 20 hp 3 phase. Noe : The cost of transportation from pump house/yard to workshop and workshop to pump house/yard shall deemed to be included in item rate quoted by contractor.

Dismantling submersible pump, straightening & polishing of pump shaft, making threading and key way, turning surfacing polishing to impellers, CI bowl complete including replacement of worn out parts as per requirement complete incl testing and all as directed of rating 5hp to 20 hp 3 Phase. Noe : The cost of transportation from pump house/yard to workshop and workshop to pump house/yard shall deemed to be included in item rate quoted by contractor.

S & F in replacement of Motor bush of gun metal upper and lower for 5 to 20 HP capacity (Set of two)

S & F in replacement of Rotor bearings sleeve upper and lower for 5 to 20 HP capacity, (set of two.)

S & F in replacement of coupling arrangement with key for motor for 5 to 20 HP capacity

S & F in replacement of Sand guard for submersible pump set for 5 to 20 HP capacity

S & F in replacement of Thrust bearing assembly for submersible pump set motor for the capacity 5 to 20 HP

S & F in replacement of Epoxy type cable jointing kit complete with all the jointing material, ferrule, for 1100 volts flat submersible copper conductor cable 16/10 Sqmm 3 core Make : M seal/Reychem/Birla 3 M

S & F of Rubber gasket (packing) suitable for 80 to 150 mm dia flange.

S & F in replacement of MS Nut bolts with spring washers of any sizes.

S & F in replacement of Steel wire rope stranded 12 mm dia for hanging of submersible pump set .

S & F in replacement of Electric cable for submersible pump set, flat 10 Sqmm 3 core stranded copper conductor PVC sheathed cable all as specified and directed. Make- Finolex/ Paragon/Havells

S & F in replacement of impeller with key and distance bushes for 5 to 20 HP capacity pump

S & F in replacement of Pump shaft of stainless steel suitable for 20 to 30 HP capacity pump

S & F in replacement of NRV for 20 to 30 HP capacity pump

S & F in replacement of Bearing bush for submersible pump for 5 to 20 HP capacity.

S & F in replacement of Bowl assembly for submersible pump set for the capacity 5 to 20 HP

S & F in replacement of Distance sleeves for submersible pump for 20 to 30 HP capacity.

rewinding of electric driven centrifugal motor 20 HP capacity AC, 3 phase, 440 volt with superior quality insulated copper winding wire of identical gauge and specification of the existing short circuited winding wires with all necessary insulating materials & applying one coat of water proof epoxy paint to the exteriors of motor and refixing at site including rubber coupling , cleaning of slots and testing complete all as specified and directed. Note: The cost of transportation from pumphouse/yard to workshop and workshop to pumphouse/yard shall deemed to be included in item rate quoted by Contractor

Repair/servicing to complete DG set any make/modal 62.5 to 200 KVA water cooled diesel engine by taking out dismantling segregation of all parts and re-assembling after duly repair/ replacement of following new part fixing including all type machine work such as turning reaming etc, washing, cleaning, greasing , wires, replacement of engine oil, gaskets, flexible coupling & all type nuts bolts washers & other minor parts as required at site and testing on completion at site. Note:- Any other accessories found unserviceable that shall be replaced & paid under respective items of this Sch.

S&F in replacement of Lub oil filter element for 62.5 to 200 KVA DG Set as per sample all as spfd.

S&F in replacement of Fuel filter element for 62.5 to 200 KVA DG Set as per sample all as spfd.

S&F in replacement of Dry type air cleaner for 62.5 to 200 KVA DG Set as per sample all as spfd.

S&F in replacement of V-Belt of fan for 62.5 to 200 KVA DG Set as per sample all as spfd.

S&F in replacement of By Pass Filter for 62.5 to 200 KVA DG Set as per sample all as spfd.

S&F in replacement of Electronic Governor Assy for 62.5 to 200 KVA DG Set as per sample all as spfd.

S&F in replacement of Starting switch of DG set up to cap 62.5 to 200 KVA as per sample all as spfd.

M&L for replacement of complete wiring (copper multistrand cable) of DG set any capacity as directed at site including thimble screw and sleaves etc

S&F in replacement of Gauge lube oil pressure of DG set cap 62.5 to 200 KVA as per sample all as spfd.

S&F in replacement of Hose pipe for of DG set cap 62.5 to 200 KVA as per sample all as spfd.

S&F in replacement of radiator hose pipe of DG set cap 62.5 to 200 KVA as per sample all as spfd.

S&F in replacement of Injector assy of DG set cap 62.5 to 200 KVA as per sample all as spfd.

S&F in replacement of Clamp hose radiator of DG set as per sample all as spfd.

S&F in replacement of water body of DG set 62.5 to 200 KVA as per sample all as spfd.

S&F in replacement of Turbo charging kit assembly of DG set 62.5 to 200 KVA as per sample all as spfd.

S&F in replacement of self starter 12/24 volt for DG set 62.5 to 200 KVA as per sample all as spfd.

S&F in replacement of AVR (Anti Voltage Regulator) for DG Set of capacity 62.5 to 200 KVA as per sample all as spfd.

S&F in replacement of Rectifier assy comprising of 230/24/12/V step down transformer heavy duty copper wound and 24 /12 V DC full wave rectifier unit as per sample for DG set 62.5 to 200 KVA as site requirment.

Repair of PT (Pressure time) fuel pump by dismantling and segregation all parts, replacement of new parts such as filter screen shut down valve, valve elbow, pulsation clamp, idle adjusting screw, high speed spring, governer plug etc in replacement of existing U/S parts re-assembling the pump after repair/ replacement of parts , celebration for DG set of capacity 62.5 to 200 KVA & testing on completion.

Repair to radiator assy Cleaning washing throughly, descaling and M&L for replacement of rubber size paid and MS Nut & Bolts including brazing /repair of cooling tubes with dismantling and segregation upper and lower chamber (tank) including and reassembling complete incl nut, bolt, washers, & spring any type for DG set capacity 62.5 to 200 KVA.

Cleaning decarbonishing complete and spray painting to complete DG Set canopy outside of capacity 62.5 KVA to 200 KVA including writing SM No, Srl No, Make, capacity & date of installation as per sample all as directed.

Disconnecting, dismentling & repair to Dynamo with segregation of all parts supply and fix in replacement of armature field, coil, carbon brush and bearing etc reassembling complete & testing on completion.

M&L for replacement of Coolant for DG set of make : Castrol/Indian Oilor equivalent

M&L for replacement of Engine oil 20 W 40 complete all as spfd. make : Castrol/Indian Oilor equivalent

Supply and fix in replacement engine Hrs run meter digital type suitable to match with existing system of DG set all as spfd.

Supply and fixing in replacement of maintinance free battery 12 volt 180 AH 25 plate including battery leads and initial charging of battery. Make :Exide/Amron.

Disconnecting, dismantling and repair/servicing to self starter 12/24 volt and replacement of field coil, carbon brush, bush or other unserviceable parts parts and refixing complete and testing after completion.

M&L in replacement of microprocessor digital type DG set controller of DG set capcity 62.5 KVA to 100 KVA ( Make of DG set- Greaves Cooton) including connect all control wiring & programming all the parameter related to DG set at site complete .

S&F in replacement of Automatic battery charger AC input 230 + 10% V output DC for 12/24 volt battery current 10-15 Amp for 02 No batteries at a time with digital ammeter and voltmeter.

S& f in replacement of Battery terminal bolt type suitable for any tpe of battery.

S& f in replacement of Battery lead of copper conductor 35 Sqmm single core fitted with suitable terminal on both side.

M & L for winding of armature winding and field winding with super enamelled copper wire of appropriate gauge incl varnishing of insulating material and heating up, testing etc complete for DG set of capacity 75 to 380 KVA incl taking out the old burnt windings.

Earthing complete with GI earth plate electrode of size 60cm X 60cm X 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides by 15 cm thick and packed layer of charcoal dust and common salt filling in alternate layers etc and connected to and including GI strip of size 32x6 mm up to 7.5 mtr by means of bolts, nuts, check nuts and washers made of brass and protected by light grade 40mm dia upto 7.5 mtr long GI pipe connected to main control board and GI pipe light grade 20mm bore for watering and including funnel, wire mesh, RCC pit cover 50mm thick and PCC chamber pit with PCC 1:2:4 type C2 (including excavation and earth work disposal of surplus soil to a distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009including taking down old unserviceable complete all as specified & directed by Engr-in-charge

DEO Traders

Charan sales and Service

M/S PASHUPATI TRADERS