Construction of a Community Hall-cum-Workshed at Dhanraj Baba Mahadalit Tola, Pagdera, in Sikatiya Panchayat under Kursakata Block (Mauza-Pagdera, Thana No.-98, Khata No.-301, Khesra-969)

Boring, Providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) :

metre

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m

Earth work in excavation in foundtion trenches or drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead.

Supplying and Filling in plinth with local sand and under floors including watering, ramming consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level:

Centering and shuttering including strutting, proping etc. and removal of form work for:

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4(1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size).

Extra for providing and mixing water profing material in cement concrete work in the proportion recommended by the manufacturers.

Providing and laying in position machine batched and mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved desing mix, Including pumping of concrete to site fo laying but excluding the cost of centering, shuttering, finishing an including retard setting of concrete, Improve workability withoutt impairing strength and admixtures in recommended proportions as per IS:9103 to accelerate, reinforcement, durability as per direction of Engineer-incharge, Note:- Cement content considered in this item is @ 330kg/cum, Excess or less cement used as per design mix is payable or recoverable separetely.

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Centering and shuttering including strutting, propping etc. and removal of form for:

Metre

Extra for additional height in centring, shuttering where ever required with adequate bracing, propping etc. including cost of de-shutering and de centring at all levels over a height of 3.5 m ,for every additional height of 1 metre or part thereof (Plan area to be measured)

Reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete.

Brick work with FLY ash bricks as per I S 12894(2002)&3495 in foundation and plinth in:cement mortar 1:6(1cement:6course sand)

Extra for Brick work in superstructure above plinth level upto floor V Level

Brick work 7cm thick with F.P.S brick of class designation 100A in cement mortar 1:3(1 cement: 3 coarse sand) in superstructure.

Half brick masonry with bricks of class designation 100A in foundations and plinth in :

Extra for half Brick masonry in superstructure above pinth level upto floor V level.

Extra for providing and placing in position 2 nos. 6mm dia, MS bars at every third course of half brick masonry (with F.P.S bricks)

Providing wood work in frames of doors,windows, clerestory windows and other frames, wrought framed and fixed in position

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S.frame shall have a coat of steel primers of approved make and manufacture . M.S. frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick,95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/sealed to the style & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC \ strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in charge, manufacturer’s specification & drawing

Providing and fixing flush door shutters non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete

Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers including necessary screws etc. complete.(best make of approved quality)

Providing and fixing aluminium but each anodised (anodic coating not less than grade AC 10 as transport or dyed requirement colour or shade with necessary screws etc.complete

Providing and fixing aluminium sliding door bolts anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with nuts and screws etc. complete:

Providing and fixing aluminium tower bolts anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing aluminium handles anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing aluminium hanging floor door stopper anodised (anodic coating not less than grade AC 10 as per IS:1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Providing and fixing bright finished brass 100mm mortice latch and lock with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS:1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality).

Providing and fixing aluminium tee chanals(heavy duty)with rollers,stop end in pelmets as curtain rod i

Providing and fixing steel glazed doors, windows and ventilators of standard rolled steel sections, joints mitred and welded with 15x3mm lugs, 10cm long, with steel lugs embedded in cement concrete blocks 15x10x10cm of 1:3:6( 1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of glass panes with glazing clips and special metal-sash putty of approved make complete including applying a priming coat of approved steel primer, excluding the cost of metal beading and other fitting except necessary hinges or pivots as required.

Extra for providing and fixing steel beading of approved shape and section with screw instead of glazing clips and metal sash putty in steel doors, windows, ventilators and composite units.

Providing and fixing pressed steel door confirming IS code 351 manufactured from commerical mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechnical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:

metre

Providing and fixing circular cast iron box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one ;pcf at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing bright finished brass casement window fastners of minimum weight 200 gms to side hung steel windows with necessary welding and machine screws etc. complete.

Providing and fixing bright finished brass peg stays 300mm long of minimum weight 330 gms. to side hung steel windows with necessary welding and machine screws etc. complete.

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including applying apriming coat of approved steel primer

Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc. complete.

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement

Providing and fixing glass strips

Providing and laying Ceramic glazed floor tiles 300x300mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in all colours, shades, except White, Ivory, Grey, Fume Red Brow laid on 20mm thick bed of Cement Mortar 1:4 (1 Cement: 4 Coarse sand) including pointing the joints with white cement and matching pigments etc. complete.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622(thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12mm thick bed of cement Mortar 1:3(1 cement: 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing designation 100A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/I.

Providing average 150mm thick dry rammed khoa beaten to 112mm (compacted with water) made of well burnt or jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1: 10) all complete as per building specification and direction of E/l,

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4( 1 cement: 2 coarse sand: 4 graded stone aggregate of 20mm nominal size) over P.V.C sheet 1mx1mx400 micron, finished with 12mm cement plaster 1:3(1 cement: 3 coarse sand) and a coat of neat cement rounding the edge sand making and finishing the outlet complete.

12mm cement plaster of mix:

15mm cement plaster on the rough side of single or half brick wall of mix:

12mm cement plaster of mix:

6mm cement plaster to ceiling of mix:

12 mm cement plaster 1:3( 1 cement: 3 coarse sand) finished with a floating coat of neat cement

White washing with lime to give an ever shade

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade

Applying priming coat:

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:

Forming groove of uniform size from 12x12mm and upto 25x15mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-Charge.

20 mm cement plaster of mix ;1: 3(1 cement: 3 coarse sand)Extra for providing and mixing water proofing material in proportion recommended by the manufacturers:

Providing and fixing water closet squatting pan (Indian type W.C pan) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C flushing cistern with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required:

Provding and fixing soil,waste and vent pipes

metre

100 mm dia

Sand cast iron S & S pipe as per IS:1729

Sand cast iron S & S pipe as per IS:1729

Providing and fixing on wall face unplasticised-PVC (working pressure 4 Kgf per sqm) rain water pipes conforming to IS:4985including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion

Metre

Providing and fixing on wall face unplasticised -PVC moulded fittings/ accessories for unplasticised PVC rainwater pipes conforming to IS:4985 including jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion.

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S screws of required length including cutting brick work and fixing in cement mortar 1:4( 1 cement: 4 coarse sand) and making good the wall etc. complete.

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Excavating trenches of required width for pipes, cables etc including excavation for sockets and dressing of sides, ramming of bottoms depth upto 1.5m ,including getting out the excavated soil , and then returning the soil as required,in the layers not exceeding 20 cm in depth including consolidating each deposited layers by ramming watering and desposing of surplus excavated soil as dirceted within a lead of 50m

Providing and laying non -pressure NP2 class(light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 including testing of joints etc. complete

Constructing brick masonary manhole in cement mortar 1:4 (1 cement, 4 coarse sand.) R.C.C. top slab with1:2:4 mix(1 cement, 2 coars e sand, 4 graded stone aggregate 20 mm nominal size) foundation cocrete 1:4:8 mix (1cement, 4 coarse sand, 8 graded stone aggregate 40 mm nominal size.) inside plastering 12 mm thick with cement mortar 1:3 (1 cement, 3 coarse sand.) finished with floating coat of neat cement and making channels in cement concrete 1:2:4. finished with floating coat of neat cement complete as per standard design.

Inside size 90x80cm and 45 cm deep including C.I. cover with frame ( light duty) 455x610 mm internal diamension tatal weight of cover and fram to be not less than 38 kg (weight of cover23 kg and weight of frame 15 kg )

Constructing soak pit 1.20x1.20x1.20 filled with brick bats including S.W.drain pipe 100 mm diameter and 1.20 m long complete as per standard design

India mark-II Hand Pump with all accessories including 8 Nos. (3 Mtr length each) connecting rod and one syllinder Confirming IS: 155000 (Part 1-8)/2008

32 mm dia medium quality G.I. Riser Pipe and 8 Nos. 3 mtre length (3 mtr each length confirming IS:1239

40 mm dia x 2 mtr, long UPVC RIBEED Strainer confirming to IS : 12818 - 1983/1992

125 mm dia x 40 mm x UPVC reducing socket (Heavy Quality)

40 mm nominal outer dia CPVC Pipe

Supplying all materials labours and equipement for constructing platform with foot rest etc. all complete job.(Detail Est attached)

Supplying drain 3 m as per design etc. all complete job.(Detail Est Attached)

Boring by jet dheki by suitable cutter or reduce as the case may be lowering 125 mm UPVC x 40 mm dia G.I. Pipe & Strainer of standard quality iron shoe, plug & socket etc. all complete including providing all tools and oplants required for the job as per sopecification and direction of the engineer in charge.

Supplying labour and equipment including 125 mm dia G.I. cap & fitting and fixing over the T/W properly and taking it out as per direction of E.I. (Cap will be property of the contractor) 1 No.

Providing all labours for fitting and fixing of India mark II hand pump including supplying all tools and plants requred for the all job complete as per direction of E/I.

Supplying all tools equipment all labours for lowering 32 mm dia medium quality G.I. Pipe (Riser pipe) in drilled T/W in 3 mtrs lenth

Providing all labour for fitting and fixing of deep cylinder with the riser pipe including necessary connecting and jointing materials, chrom leather bucket all tools & plants required for the job low water lever all complete job as per specification and direction of E/I.

Supplying all materials & labours for arrangement of additional water required during the drilling work all complete job as per specification and direction of E/I.

Developing and t Testing of T/W till the discharge is free from sand one item all complete job as per specification and direction of E/I.

Providing earth work in excavation

Supplying and Filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,

Providing P.C.C(1:2:4) in F&P ……do….do…..all complete job

Providing and laying in position specified grade of reinforcedcement concrete excluding the cost ofcentring,shuttering,finishing and reinforcement-All work putoplinth level 1:2:4 (1 cement:2 coarse sand:4 graded stoneaggregate 20 rr,m nominal size)

Providign 100A B/W(1:4) in superstructure etc. all complete job.

Providign 100A B/W(1:6) in superstructure etc. all complete job.

Providing M-S reinfrocement etc .all complete job.

Providing 12mm thcik CP(1:3) on overall roof surface

Providing 12 mm thick C.P (1:6) in all etc. all complete job.

50 mm size brick aggrigate outer side of soak pit

Wiring for light point/ fan point/ exhaust fan point / call bell point with 1.5 Sq.mm FR PVC insulated copper conductor single core cable in surface/ recessed PVC conduit with piano type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq mm FR PVC insulated copper conductor single core cable etc as required. Group- B a. Light/ call bell points - 27 b. Ceiling fan points - 07 c. Ex. Fan points - 02 Total - 36

Supplying and fixing 3 pin 5/6 amps socket outlet & 6A switch piano type on the existing switch box including connections etc. as required.

Supplying and fixing suitable size GI/PVC box on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 3 pin 5/6 amps socket outlet & 6A switch piano type connection painting etc. as required.

Supplying and drawing low resistance co-axial T.V cable RJ-6 grade copper conductor PE insulated, with PVC sheath in the existing PVC concuit etc. as required.

Supplying and fixing piano type T.V antenna socket on the existing metal box including making connection, etc. as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes PVC insulated copper conductor, single core cable in surface / recessed PVC conduit as required.

Meter

Meter

Supplying and fixing metal box of following size in recess with suitable size of phenolic laminated sheet cover in the front including painting etc. as required.

Supplying and fixing 8 way double door sinle pole and Neutral sheet steel M.C.B. D.B, 240 Volts in recess, complete with tinned copper busbar, neutral bus bar, earth bar, din bar , detachable gland plate, interconnection, phosphatized and powder painted including nting, earthing etc. as required ( But without MCB/ RCCB/Isolator)(UPS DB)

Supplying and fixing of following rating C series MCB suitable for inductive and other loads of following poles in the existing MCB DB complete witth connections ,testing and commissioning etc. as required .

Earthing with G.I earth pipe 4.5 mt. long 40mm dia including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. including providing salt and charcoal for pipe earth electrode as required.

Providing and laying earth connections from earth electode with 4.00 mm. Dia copper wire in 15 mm. Dia G.I.pipe from earth electrode as required.

Providing and fixing 25mmX5mm GI strip on surface for connection etc as required.

Providing and fixing 4mm dia copper wire on surface or in recess for loop earthing etc as required.

Supplying and fixing bulkhead fitting die cast aluminium alloy body with prismatic glass cover suitable for the GLS/CFL lamp directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated, copper conductor single core cable etc. as required.

Supplying and fixing 2 pin 5 Amp ceiling rose on the existing junction box/ PVC box including connection etc as required.

Supplying and fixing batten / angle holder including connections with 1.5 sq.mm FR PVC insulated, copper conductor single core cable etc. as required.

Supplying and fixing following types lamp in existing electrical fitting/ fixture etc as required.

Supplying and installation of regular/standard model A.C. ceiling fan of 1200 mm sweep including wiring the down rods of stanard length ( upto 30 cm) with 1.5 sq. mm FR PVC insulated insulated copper conductor etc as required.

Supply and Installation of 300 mm, 230 V A.C. exhaust fan in the existing opening, including making good the damage, including making good the damage, connection, testing, commissioning etc. as required.

Supplying and fixing powder coated strip fitting complete with electronic ballast, 4'x40 watt fluorescent lamp etc. directly on ceiling / wall including connections with 1.5 sq.mm FR PVC insulated, copper conductor single core cable etc. as required.

Making 25 cm (10") dia bore up to 4 mtr depth below ground with hand auger of approved quality in ordinary soi! (vide classification of soil item A ) true to plumb and without eccentri city in any stage of operation and disposal of the excavated earth up to 50 mtr , Lead in eluding all lifts , all complete as per approved disign anddirection of E/l Details of cost for 4 piles of 4 m= 16 mtrsBoring,providing & installing bored cast-in-situ R.C.C Piles

metre

Supplying and Filling in plinth with local sand and under floors including watering, ramming consolidating and dressing complete.

Providing designation 100A one brick flat soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/I.

Providing and laying in position machine batched, machine mixed andmachine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering finishing and reinforcement, M-20 grade reinforced cement concrete

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Centering and shuttering including strutting, propping etc. and removal of form for:

Reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete.

Brick work with FLY ash bricks as per I S 12894(2002)&3495 in foundation and plinth in:cement mortar 1:6(1cement:6course sand)

Extra for Brick work in superstructure above plinth level upto floor V Level

Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. all complete.

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required.

12mm cement plaster of mix:

Finishing walls with water proofing cement paint of approved brand and manufacture and of required shade to give an even shade

Applying priming coat:

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: