Renovation work of Essential works for Auditorium at RIMS, Ranchi.

Amount

Dismantling wooden trellis work excluding frames but including stacking the serviceable material within 50 metres lead

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Labour for cutting old mosaic or precast terrazo tiles including cost of removing dirt, rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curring, taxes and royalty all complete as per building specification and direction of E/I.

Leak repair to G.C.I. Sheet roof including fitting and fixing with new bitumen and limpet washer, closing bolts at all places all complete as per building specification and direction of E/I.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick flat

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : 12.51.1 Ridges plain (500 - 600mm)

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

38 mm thick wood block flooring of first class teak wood laid over 25 mm thick leveling layer of cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 10 mm nominal size) to be paid separately, coated with a thin layer of hot bitumen penetration 80/25 (blown type) @ 2.45 kg per sqm, including fixing blocks in position after dipping in hot bitumen (blown type) up to half depth, planed, levelled smooth and finished complete.

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing, taxes and royalty all complete as per building specification and direciton of E/l.

With "A" grade white 15 x 15 cm tiles.

Taking down old door and window shutters including stacking serviceable materials within 15M. lead and disposal of unserviceable materials with all leads all complete as per direciton of E/l.

Suppling, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows, skylight, fanlights and celetial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type non-decorative double leaf flush shutters in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing two coats of synthetic enamel paint over a coat of primer of approved shade and make over new wooden surface after cleaning, removing dirt, scales, smokes, grease and sand papering, including cost of scaffolding and taxes all complete as per building specfication and direction of E/l.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding, washing of floor and taxes all complete as per building specification and direction of E/I.

Providing two coats of plastic emulsion paint of approved shade and make over old surface including washing cleaning and preparing the walls scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:

New work (Two or more coats applied @ 1.43 ltr/10 sqmover and including priming coat of exterior primer applied@ 2.20 kg/10 sqm)

Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface

Finishing walls with textured exterior paint of required shade : 13.110.1 Old work (Two or more coats on existing cement paint surface applied @ 3.28 ltr/10 sqm

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Carriage of Materials

Sand Lead 10km

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.

(A) 580 mm long (c) With 10 lit. low level PVC cistern

Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. (A) P TRAP (b) With 10 lit. low level PVC cistern

Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthenware urinal of "Hindustan" " Parry" or any other approved I.S.S. make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15 mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grms. , 15 mm P.V.C. alkathene pipe 450 mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l.

(A) Flat back or standing corner ( 450 mm x 350 mm )

Supply Fitting and Fixing VIP Bath room Fittings do-do

Bib Cock Long Thread

Angular Stop Cock

Mirror of 6 mm thick 600 x 450 mm

Pillar Cock (ISI) Long Neck

Glass Self 22'

Soap Dish

Towel rail

Steel Jali

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c ing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.

20 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

25 mm nominal dia Pipes

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion (i)single socketed pipes

75 mm Diameter

110 mm diameter

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete

100 mm clip

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler

Single pushfit Coupler

Single tee with door

Shoe (Plain)

75 mm Diameter

110mm Diameter

Supplying materials and labours for constructing inspection chamber of designation class 75B bricks size 750mm deep , 600x450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600x475mm G.I. Cover with frame (weight not less than 36 kg ) along with earth work in excavation and 80 mm thick P.C.C (1:3:6) in foundation and refilling all complete as per specification and direction of E/I

Providing post construction Anti tremite trearment for existing floor and wall as per technical specification 1. IMSS expert detects the termite entry points,their pathways and extend of infection .Based on this understanding IMSS Experts Designs the appropriate type and level of treatment. 2. Latest and high effective Drill-Fill-Seal technique and inject chemicals to form a barrier that prevent termites from coming in . 3. Useing scientific methods to conduct regular checks and prevention by conductiong systematic inspection at regular interval to ensure complete protection. 4. treatment comprises drilling holes in the junction of floor and wall,soaking them with the termiticide and sealing them to completly undetectable chemicalbarrier around your property

Supply fitting and fixingall heightwall panneling of 12mm thick water proof oly (centure panic pine wood,ISI Mark,Termites) over 2"x1" aluminium section,4mm thick water proof veneer (green dacore wood) finishing with malamine polished all complete including all taxes and royalty all complete as per building specification and direction of e/i.

Supply and installation of anutone strand ebony,kerfd edge magnesite bonded pinewood fibre core tils of size 600x2400x25mm,density 400kgs m3 weight 10kg/m2 installed by using anutone strut fraame work system with non visible fastener using anutone struct-spline.The Strucutre frame work systems included anutone strut cc25 cross channel having thickness .70mm length 3600mm Knurled web 25,depth 25mm and equal flanges 15mm is fastened to wall position horizontally in a regular manner at 600mm c/c.The Square edge panels shall be then screw fixed along their long edges of 2400mm against frame work to perfect fit with staggered short edge. Acoustics-NRS0.87, TECHNICAL-FIRE CLASS-1&P Thermal climate (0C,light greeen),Conductivety -(W/MK)-0.08(RH)-50,90 REFLECTANCE(%)-lOW LIGHT REFLECTIVITY(voc,rc) lOW-30

Supply and installation of Anutone Salon Slat made of pine wood E1 grade fiberboard.Melamine/venner lamination finish,grove perforated slats L8-2(2mm grooves@ 8mm centers)/L16-2 (2MM Slates @ 16mm pitch)/L32-2weight of 12kg/sqm installed by usingGI Strut system.the GI Strut system including GI Cross channel CC25 having thickness .450x3600 knurled web 40mm depth 25mm and equal flages of 15mm is fastened vertically/horizontally at every 600mm centers.Aluminium core cross channels CC 18 having thickness0.5mm length 2440mm web 15mm & 24mm ,depth 18mm and flanges of 7mm with suitable gdge & center bracket is then fixed perpendicular to the CC25 with the help of fasteners of 7mm with the help of fasterners at every 400mm centers,slats of size 128x2400 16mm in then fixed perpendicular to CC18 with suitable edges & center bracket panels shall be backlined with acoustical in fillof Anutone Synth PF5X25MM thick adhered to the wall using stick 7 adhesive.Technical Parameters-core Variants-Pinewood E1 Fiberboard ,Fire reflectance-75%,green (depend upone colour),Hygiene (Voc,Clean room)-Low Class1,Strength ,Load Capacity kg -Anitsag,Ball-impact

Supplying , fitting and fixing Jaquwar make Metropole flush valves regular Model- FLV 1093N 40 mm size (concealed body ) with exposed shut off provision and round flange

Supplying , fitting and fixing Jaquwar make Wall Hung basin with fixing Accessories Size -590 x 490 x 185 mm including LYS - WHT - 38301 full pedestal for 38801

Add 18 % GST (in Basic Rate must fill 12)

Add 1% Labour Cess (in Basic Rate must fill 1)

M/s Akhileswar Singh