SPL REPAIR TO BLDG NO P-164 UNDER GE GWALIOR

Amount

Demolition of cement concrete (unreinforced) in ground floor and paving not exceeding 15 cm thickness (below or above ground level) incl the disposal upto 50M complete all as specified and directed.

Demolition of Reinforced Cement Concrete (Existing RCC water tank, kitchen shelves etc ) of any description and in any position not otherwise specifically provided for complete all as specified and directed

M & L for Reinforced cement concrete (nominal mix) in type B1 1:2:4 (20mm graded aggregate) Slab supported on walls, beams and columns in floors, roofs, landing, balconies,desk slabs and in Kitchen shelves and like including form work complete all as specified and directed.

M&L for mild steel TMT bars ,10mm dia and over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

M&L for cement concrete type E2 1:5:10 (using 40mm graded stone aggregate) as in sub base of floor or sunken floor etc complete all as specified and directed.

M&L for 25 mm thick cement concrete type B0, 1:2:4 (using 12.5mm graded stone aggregate) as in leveling course complete all as specified and directed.

Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for non - skid ceramic tile coloured 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match, including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for non - skid ceramic tile coloured 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, on vertical surface such as skirting, dados and risers to steps etc set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including rendering 10 mm thick on fair faces brick work or concrete surface in cement plaster 1:4 complete all as specified and directed.

M&L non-skid ceramic coloured tiles, rectified, joint free, 7 to 8mm thick, matte finish (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles, over screed bed or bedding layer 15 mm thick of cement mortar 1:4 complete all as specified and directed.

M&L for glazed ceramic coloured tiles in vertical surface 350mm x 250mm x 7mm/ 450 x 300 x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match, aid over and including rendering 10 mm thick on fair faces brick work or concrete surface in cement plaster 1:4 complete all as specified and directed.

Dismantling of stone slab and tiles of any description or thickness in floor, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

M&L for machine cut Kota stone slab 18 to 20mm thick , as in flooring , laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and including screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:6 ) complete all as specified and directed.

M&L for machine cut kota stone slab 18-20 mm thick as in riser / steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing over and including 10 mm thick backing coat in CM (1:4) complete all as specified and directed.

M&L for 16-20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including rounding/ chamfering edges, pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for Brickwork with subclass 'B' bricks old size brick, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement plaster 1:6, finished even and smooth (without using extra lime or cement) complete all as specified and directed.

M&L for rendering 5 mm thick on faces or brick work ,concrete surfaces, in ceiling & in cm 1:3, finished even and smooth (without using extra lime or cement) complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement plaster 1:4 and mixed with WPC , finished even and smooth (without using extra lime or cement) complete all as specified and directed. (Note:- WPC shall be measured & paid seperately).

M&L for preparation of the newly plastered surfaces of walls & applying 3 coats of white wash on wall surfaces complete all as specified and directed.

M&L for complete removal of existing treatment of walls and applying three coat of white wash complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of ceilings & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed.

M&L for complete removal of existing treatment of ceilings and applying three coat of white wash complete all as specified and directed.

M&L for Preparation of new plaster surfaces of walls, applying 2-3 mm wall care putty on walls and Distempering with 1st quality acrylic distemper(ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats over a coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment and Distempering with 1st quality acrylic distemper(ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats over a coat of primer complete all as specified and directed.

M&L, Preparation of new plaster surfaces of walls and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm all as specified and as directed by the Engineer in charge. .

M&L for complete removal of exiting treatment from external walls (any no of layers ) by scrapping with steel scrappers or any other means, preparation of old surfaces complete applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm all as specified and as directed by the Engineer in charge.

Taking down steel tubing and connection 15mm bore incl cleaning for refixing or removing from site complete all as specified and directed.

Taking down steel tubing and connection 20mm bore incl cleaning for refixing or removing from site complete all as specified and directed.

M&L for GI tubing 15mm dia medium grade galvanised with all fittings fixed to wall and floor complete all as specified and directed.

M&L for GI tubing 20mm dia medium grade galvanised with all fittings fixed to wall and floor complete all as specified and directed.

S&F in replacement bib taps, fancy type 15 mm caste copper alloy long body, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe and fixed complete all as specified and directed.

S&F, in replacement 15mm Angle stop valve of CP brass any colour high pressure screwed for iron pipe or for union fixed complete all as specified and directed.

S&F in replacement PVC connection 15mm size with PTMT nuts on both ends of length 450 mm complete all as specified and directed.

S&F in replacement swivel shower of brass chromium plated of size 125mm for fixing with 15mm bore pipe complete all as specified and directed.

S &F in replacements tublar towel rail aluminium anodised 20mm dia D type 60 cm long between flange brass chromium plated complete all as specified & directed.

S&F in replacement for Soap dish of CP fixed with pvc rawal plugs and screw, complete all as specified and directed.

S&F in replacement Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

S&F in replacement Stainless Steel Peg Set of 6 hooks ISI marked medium weight complete all as specified and directed.

S&F in replacement grating 100/125 mm dia of PTMT, fixed to Nahani trap complete all as specified and directed.

S&F in replacement stainless steel kitchen plate rack made out of 0.63mm thick stainless steel of size 900x750 mm including screws and wt not less than 5.00 Kg complete all as specified and directed.

S&F in replacement kitchen sinks with drainage board made of stainless steel 1mm thick with kitchen or laboratory with plug, washers, wastes, including fixing (cantilever brackets and connecting union to pipe overall size 915mm x 460mm boul size 410mm x 330mm x 160mm) complete all as specified and directed.

S&F in replacement wash hand basin vitreous china (flat back) of size 550 x 400 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets cutting for and pinning in ends complete complete all as specified and directed.

S&F in replacement 32 mm waste fittings, brass chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly -nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in replacement Brass CP mixer for basin mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F, in replacement 15 mm bore, cast copper alloy chromium plated fancy type wall mixer tap with telephonic shower (3-in-1 system) for cold & hot water wall mixer having inclusive connection for shower complete all as specified and as directed (Make Prayag or Equivalent as approved)

S&F in replacement vitreous china squatting pan "(Orrissa" pattern) size 580 x 440mm white with integral foot rests (excluding flushing cistern and flush pipe ) complete all as specified and directed.

S&F in replacement PVC flushing cistern 10 Ltrs capacity including all fitting flush pipe etc complete all as specified and directed.

S&F for rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of capacity 1000 litres hoisted and fixed in position all as specified in SSR Part-I, complete all as specified and directed.

S&F in replacement Ball brass valves high pressure with polythene float and flynut complete screwed for iron pipe of 20mm bore of brass ferrule complete all as specified and directed

S&F, in replacement 20mm stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union fixed complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories), complete all as specified and directed.

S&F 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls or laid in trenches/ floors, complete all as specified and directed.

S&F 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls or laid in trenches/ floors, complete all as specified and directed.

S&F PVC (SWR) bends any radius, 110mm bore, complete all as specified and directed.

S&F PVC (SWR) bends any radius, 75mm bore, complete all as specified and directed.

S&F PVC (SWR) junction single (single T), equal or unequal, 110mm bore, complete all as specified and directed.

S&F PVC (SWR) junction single (single T), equal or unequal, 75mm bore, complete all as specified and directed.

S&F for 110mm dia PVC(SWR) vent cowl, complete all as specified and directed.

S&F in replacement for PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F in replacement for PVC (SWR) 'P' or 'S' trap 110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F in replacement for PVC (SWR) floor trap/ Nahani trap 75mm, plain with greating including setting and jointing with solvent cement complete all as specified and directed.

Taking down chowkhat frame with shutter (without taking out shutter from the frame) n.exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkhat frame with shutter (without taking out shutter from the frame) exc 1.50 Sqm but n exc 4 sqm each complete all as specified and directed.

Supply and fixing factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge

Factory made single extruded WPC (Wood Polymer Composite) solid decorative/laminated door/ window/Ceosetory windows & other Frames/ Chowkhat of size 125 x 65 mm Double rebated comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge.

ditto- but Frames/ Chowkhat of size 100 x 65 mm Single rebated complete as per direction of Engineer-in-Charge.

Supply and fixing 24 mm thick factory made PVC door shutters to existing door frames made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and jointed at the corners by means of M.S. galvanized/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as specified by the manufacturer and as per directions of Engineer- in-charge. (For W.C. and bathroom door shutter).

S&F for 35 mm thick skeleton shutters of 2nd class Hard Wood for door, open rebated and prepare to reveive glass, guage etc (without sash bars ) edges of framing plain chamfered or rounded, fitted with for securing glass etc, size of members of shutters as specified in SSR Pt-I, section 8, clause 8.24(a) complete all as specified and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid decorative type/laminated flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.

S & F Anodised powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors , windows , ventilators, partitions with one or more rebates including jointing cleat for fixing etc.

S & F anodised powder coated aluminium windows, ventillators shutters, slidding type, aluminium section weighing not less than 0.55 kg/m including necessary jointing cleats, Glazing clips , rubber neoprene packing, anodised aluminium snap beading screws, locking latches, roller assembly etc complete.

S & F anodised powder coated aluminium windows, ventillators shutters, side hung type, without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary jointing cleats, Glazing clips , rubber neoprene packing, anodised aluminium snap beading screws, anodised aluminium fittings such as peg stays 150mm long (1 No). hingestype B-21 100mm long (2 no.) suitable handle (1 no.) locking latches etc complete all as specified and directed.

S&F MS framed work as in grill or framed guard bars with end of bars welded or riveted into spikes conforming to Fe- 290 Gde E-165 complete all as specified and directed.

Supply only 3mm thick figured glass pin head type in square n.exc 0.5 Sqm in each pane new ventilator / window shutter complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed

S&F for 200 mm aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for extruded aluminium alloy handles 150 mm, fabricated type, anodised complete all as specified and directed.

S&F for 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 fixed complete all as specified and directed.

S&F aluminum alloy anodized sliding door bolt 300mm long with hasp and staple (bolt type) and fixing clip of sheet and cast in extruded section and fixing bolts and sliding bolt of extruded section complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

S&F for 18 mm thick PVC Celuka ply of one side prelaminated and other side plain white colour fixed with screws ,solvent cement /adehesive complete all as specified .

S&F for continous (piano) hinges , mild steel, bright finished or electrogalvanised, width of flap 30mm complete all as specified and directed.

S&F for mild steel Easy- slide auto Hydraulic hinges (CH-S-8), package contains 2 units of hinges with 4 Nos screw for kitchen cabinet, Cup board, wardrobe etc complete all as specified and directed.

S&F for 12 mm thick PVC Celuka ply of both side prelaminated and other side plain white colour fixed with screws ,solvent cement /adehesive complete all as specified .

S&F for magnate catcher of metal body and striking plate heavy duty includind fixed with screw, complete all as specified and directed.

S&F Brass 2 Levers Cupboard locks grade 1, Size 50mm complete all as specified and directed.

S&F for 100 mm Brass handles, cast type, polished bright and fixed complete all as specified and directed.

M&L for preparation of new steel surface of any description exceeding 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for for applying one coat of synthetic enamel paint on old steel & iron surfaces (previously decorated) for grills, guard bars of any description not otherwise described over 10cm in width or girth including preparation of old surfaces complete all as specified and as directed.

M&L for preparation of new wood or wood based surface of any description exceeding 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for cutting out cracks to V section in existing walls, roofing or terrace, cleaning out wetting grouting with cement and sand slurry 1:3 complete all as specified and directed.

S&F in replacement for curtain rod of Stainless steel 23-25 mm dia pipe thickness not less than 0.8mm of pipe with fixing bracket, side nobes etc fixed on walls with screws with PVC rawl plugs etc complete all as specified and directed.

Removing existing water proofing treatment (Brick tile terracing), roughning of concrete surfaces, cleaning of concrete surfaces with water and removing debries/rubbish off materials out side of Ministry of defence (MOD) land complete all as specified.

M&L, 10mm thick screed bed or cement mortar 1: 4 on concrete surfaces mixed with WPC, complete all as specified and as directed. (WPC shall be measured & paid seperately).

Supply only integral liquid water proofing compound (ISI marked) complete all as specified and directed.

M&L, bitumenous based primer conforming to IS-3384-1965 @ 0.40 Kg / Sqm including preparation of roof surface complete all as specified and as directed.

M&L, Cutting grooves in brick wall, 75mm wide and 65mm deep, pinning in felt and shaping horizontal face of groove with cement mortar 1:3 all as specified and as directed.

M&L, for APP based polymeric membrane minimum weighing 3.5kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid on primed surface by torch application method complete all as specified.(Make:- IWL, STP, Sika)

M&L, for precast cement concrete tiles of size 250mm x 250mm x 22mm as in roof top ,confirming to IS-1237-1980 laid over 15 mm thick screed bed in CM 1:6 and set, jointed with grey cement & no Pigment and pointed in neat cement slurry in floors, and cut & polished between tiles 2 to 3 mm will be filled with cement mortar (1:2) by mixing of chemical or equilant approved by the Engr-in-charge complete all as specified and as directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggrtegate as in plinth protection/path and the like including finsihing even & fair complete all as specified and directed.

M&L for 100 mm thick cement concrete type D-2 1:4:8 (using 40 mm graded stone aggregate), as in sub base for floor, finished even and rough complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

M&L for 60 mm thickness machine pressed precast concrete interlocking paver block M-35 any shape and size, confirming to IS 15658-2006 in grey cement glossy finish rubber mould casted laid dry over sand cushioning complete all as specified and directed.

Taking down carefully existing aluminum / copper point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, pendants, tube light fitting, ceiling fan with regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces of walls, floors, ceiling etc to match with existing surfaces complete all as specified and directed.

Taking down ceiling fan of any sweep,removing blades, cleaning the fan completely of dust and dirt and Re-hanging the same back to its original positions including connecting with three core flexible copper wire to ceiling rose etc after the completion of the point wiring including replacement of old unserviceable fan hook rubber pad, nut bolts and washers etc, complete all as specified and as directed by Engr-in-charge.

Taking down submain wiring of any size any type and in any position metalic/non metallic PVC conduit of wooden batten complete all as specified and directed.

Taking down unserviceable Sheet metal box & MCB DB SPN with MCB's of any make/capacity, complete, all as specified and directed by Engr-In-Charge.

Taking down unserviceable TPN DB with MCB's of any make/capacity, complete, all as specified and directed by Engr-In-Charge.

M&L, concealed point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH confirming to IS 694:2010 having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional area (ISI marked with valid CML No) drawn in and including concealed non metallic rigid PVC conduit medium grade( ISI marked with valid CML No) not less than 20 mm dia with all fitting and fixing accessories and 1.5 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to common earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxes factory made for mounting switch, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside for mounting switches. sockets etc complete

One light point controlled by one switch.

One Ceiling fan point controlled by one switch.

One Exhaust fan point controlled by one switch.

One 5 pin multipurpose socket out let 5/6 Amps on the same board with other switch.

One 3 pin/5 pin switch socket outlet, 5 Amps on independent board.

One Bell/Buzzer point controlled by one way 5 Amp push button switch.

One light point controlled by 2- two way switch

Description all as per item No 6 here in before but point wiring with 2.5 sqmm FRLSH H confirming to IS 694:2010, multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 2.5 sqmm FRLSH PVC insulated multi strand copper conductor cable as continous earth wire.

S&F Modular switch 1 way 6 A,1 module complete all as specified and directed.

S&F Socket, 6A - 2/3 pin combined 2 module,complete all as specified and directed.

S&F Modular switch 1 way 16 A,1 module complete all as specified and directed.

S&F Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S&F Modular switch 2 way ,6 A,1 module complete all as specified and directed.

S&F ceiling rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed.

S&F Fan step regulator, 120W - 2 module 240 volts, AC 50Hz complete all as specified and directed.

S&F of buzzer Ding Dong, AC, 230 Volts, single pole complete all as specified and directed.

S&F Modular Bell push ,6A ,1 module complete all as specified and directed.

S&F Lamp holder with metal ring, PVC/Polycarbonate type with back plate suitable for batten fittings ISI Marked complete.

S&F LED Lamp 09/10, efficiency > 120 lumen/wattwatt complete with 5 star rating.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 25 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 4 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. (NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 2.5 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 20 mm dia with all fitting & fixing accessories including one run single core PVC insulated unsheathed 2.5 Sqmm FRLSH confirming to IS 14930 (Part-I) 2001, copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. (NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

S&F Decorative ultra slim LED Tubelight fitting of LED with extruded polycarbonate, enviormental friendly energy efficient ready to use, 20 watt, 6500K fitting ,Efficiency >110 lumen /watt incluing reqd length of not less than 1.0 Sqmm PVC multistranded BIS marked 03/02 core copper conductor for electrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed.

S & F security light fittings better optics for uniform distribution IP 65 protection LED of 30 watt with Photometric sensor outdoor type 220-240 volt ambient light <5-15 lux working temparature -20~+40C working humidity <93% RH along with pvc connection of 6 to 10 amp capacity , Heat resistance glass, pressure die cast aluminium housing including 25mm dia galvanised iron pipe light grade bracket bent to shape over all length 0.60mtr fixed to wall with 02 Nos FI clamps made of 40 x 5 mm FI, 15 cm long, 8 mm dia bolts and nuts with washers grouted in wall complete including reqd length of 1.5 Sqmm PVC multistranded BIS marked, 03 core copper conductor for connection from ceiling rose to light fittings incl testing on completion all as specified and directed.

Supply, install, commissioning and installation of distribution meter box indoor type, factory made out of CRCA sheet 2mm thick complete with inside, outside powder coated independed housing for meters with transperent glass & rubber gasket packing with suitable size copper single/ two core wire for each control, cable gland, with 200 Amp rated TPN aluminium busbar (for outgoing) duly insulated (including self insulated) maintaining proper space for each busbar and grouting panel in wall etc complete including self closing locking arrangement and comprising for following fittings (i) MCCB TPN, 63 Amps ,16 KA - 01 No (For incoming) (ii) Amp Meter (0-100 Amp)- 01 Nos (iii) Volts Meter (0-500 Volts ) - 01 No (iv) Indicator Lamp set of three R,Y,B - 01 Set (v) ASS & VSS with CTs -02 Nos ( 01 Each) (vi) MCB SP 40 Amps, 230 volts - 04 Nos (For outgoing) (vii) Nutral bus bar link mounted on insulator (viii) Place for fixing the energy meter. - 04 Nos (ix) The quoted rate is inclusive of removing the existing electric meter from the building and re fixing the same in the sheet metal enclosure at the same location without any damage to the meter. Note;- (i) Cable entry gland made of polycarbonate of appropriated size shall be provided in each cable / wire entry as per IS standered. (ii) All internal wiring inside the panel used for metring purpose shall be PVC insulated FRLSH, ISI marked of size not less than 1.5 Sqmm.

S&F MCB DB, sheet metal enclosures double door SPN 8 way with bus bar 240 volts 2 in 1 shutter type (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S&F, MCB SPN 63 Amps, 240 volts 'C' series 16 KA ,including connection with suitable size copper lugs complete all as specified and directed.

S&F, MCB SP 240 volts, 40 Amps, 'C' series 10 KA including connection with suitable size copper lugs. complete all as specified and directed.

S & F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amp.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area size 25 Sqmm 3.5 Core.

Excavation in trenches n exc. 1.5 m wide and n' exc. 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling of excavated soil, including spreading leveling, watering and well ramming in layers, not exceeding 25cm complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 m and depositing where directed at a level n exc 1.5m above the starting point complete.

Sand filling in trenches with clean dry unwashed sand free from sharp particles, gently punning around the cables complete.

Supplying and laying un reinforced precast concrete cable cover Class LV, Type I, flat size 250mm x 150mm x 40mm complete all as specified and directed.

S&F tube 'Light' grade galvanised with all fitting laid in trenches, fixed to wall and floor of 50 mm dia for cable protection complete all as specified and directed.

Supply and fix cable jointing kit for 1.1 KV grade cable for end joint complete with Jointing material heat Shrink type and accessories suitable for 3 ½ / 4 core XLPE, armoured, Al conductor cable of size 25 to 50 sqmm,Indoor/Outdoor type

Taking out old u/s pipe line alongwith fittings from existing connections of size 25 mm dia complete all as specifies and directed.

Taking out old u/s pipe line alongwith fittings from existing connections of size 20 mm dia complete all as specifies and directed.

M & L for GI pipe Med grade of 25 mm dia alongwith all fittings and fixtures complete laid in trenches all as specified and directed.

M & L for GI pipe Med grade of 20 mm dia alongwith all fittings and fixtures complete laid in trenches all as specified and directed.

S&F 25 mm Brass Gate Valve cofiorming to IS 14846/2000,ISI Mark MS Spindle and iron wheel head with both ends flanged with new rubber gasket,bolts and nuts including dismantling of old u/s Gate valve fixed at any location of size 25 mmm dia all as specified and directed.

S&F 20 mm Brass Gate Valve cofiorming to IS 14846/2000,ISI Mark MS Spindle and iron wheel head with both ends flanged with new rubber gasket,bolts and nuts including dismantling of old u/s Gate valve fixed at any location of size 20 mm dia all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test. Testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded BT stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12 mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI medium grade earth lead protection pipe including provn of earth test point made of 50 x 5 mm MS Flat in 'D' shape 500 mm legth grouted in wall complete 01 x 6 mm multistrand PVC insulated copper conductor ( Green Colour) to be provided from test point to DB through 20 mm dia concealed non metallic conduit complete all as specified and directed as per MES Schedule Part I & II..

Babatia super works (BID ID -3291365)

M/S MAHAVIR SINGH (BID ID -3290776)

M/S NIRMAL SINGH DHANJAL (BID ID -3291119)

tanay enterprises (BID ID -3291462)

M/s Himgiri construction (BID ID -3291423)

M/S SHRI DIWAKAR SINGH (BID ID -3290781)

MAHARAJ KUNWAR SAHAB CONSTRUCTION (BID ID -3291406)

K C ASSOCIATES (BID ID -3291385)

vikas traders (BID ID -3290779)