ADDN ALTN AND SPECIAL REPAIRS TO DOORS AND WINDOWS OF SAILORS MARRIED ACCOMMODATION R S BLDG AT NAVY NAGAR AND PROVISION OF COVERED SHED ASSOCIATED FIXTURE FOR REFUSE DISPOSAL AT NAVAL STATION KARANJA

Amount

Taking down chowkats or frames including shutter (without taking off shutters from the frame) area n exc. 1.5 Sqm each all as specified and directed.

All as per item above but exc 1.50 Sqm n.exc 4 Sqm all as specified and directed.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm each and refixing in same opening incl easing, adjusting etc all as specified and directed.

M&L Kota stone slab 20-25mm thick in riser of steps, skirting, dado/widow & pillar over 10mm thick plater in CM (1:3) & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified.

S&F Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDMrubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Aluminium anodised grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC15) of approved design/pattern(DG 104), with approved standard section and fixed to existing window frame with CP brass/stainles steel screwnot less than 50mm and @ 200mm c/c, incl cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised alu standard section ( 28mm x 19mm x 2mm thick)around the opening, all complete as per requirement and direction of EIC.

S&F in 4mm thick plain sheet glass of ordinary quality for aluminium windows of any size including rubber beading etc all as directed and specified.

S & F in 4mm thick frosted glass, ordinary quality and glazing with oil putty of any size pane complete all as specified.

M&L 2nd class HW, Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid rounded or chanbered, put together with glue pinned at joints.

S&F 35mm thik plain, framed, factory made panelled shutter(two panel) with lock rail and panel of 9 mm B.W.P. commercial veneering particle board on both faces. The size of rail and stile as per IS : 1003(Part-1), kiln in seasoned and chemically pressure treated.

S&F 35mm thick 2nd class HW, glazed and skelton shutters open rebated and prepared to receive glass / gauge (without sash bar) edges of forming plain chamfered orrounded fitted with cut and mitred bead for securing glass / gauge etc size of shutter as per SSR part-1 section 8 clause 8.24(a).

S&F Factory made solid panel PVC door shutter 30mm (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded wood grain printed PVC sheet used 5mm thick x 15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (90o) used instead of exposed portion of PVC sheet beading panelling of wood grain printed PVC sheets to be fitted in the MS frame welded sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, supling & fixing in the frame at the site as per specification and drawing shown in SSR Pt-I all as directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube and edges will be painted to match with printed sheet fixing in opending as per specification and drawing etc complete all as specified.

S&F MS butt hinges100mm long medium weight, cold rolled.

S&F 100 mm long ,Butt hinges, extruded aluminiumalloy with galvanised mild steel hinge pin, anodised and fixed, type B-21.

S&F 125 mm long extruded alu alloy handles, fabricated type, anodised.

S&F 150 mm long extruded alu alloy handles, fabricated type, anodised.

S&F 300mm aluminium alloy, anodised, sliding door bolt with hasp, staple bolt type and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy.

S&F 150mm long Aluminium,anodized barrel tower bolts of extruded section and fixed.

S&F 200mm long Aluminium,anodized barrel tower bolts of extruded section and fixed.

M&L Preparation of new wooden surfaces over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer.

M&L Preparation of old wooden surfaces over 10cm width or girth, not otherwise described and applying one coat of synthetic enamel paint.

Preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainless steel wire staples all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainless steel wire staples as in repairs.

Taking down cement plaster of any description incl raking out joints, hacking for key, scrubbing down with water etc. all as specified and directed.

M&L 20 mm thick polymer modified ready mix cement based plaster on external surfaces complete all as specified and directed.

M & L 8 mm thick ready mixed cement base plaster on internal surfaces on brick or concrete surfaces complete all as specified and directed.

Supply only integral water proofing compound.

M & L for preparation of newly or untreated plastered surface applying two coats of oil bound distemper (OBD) over a coat alkali resistant primer complete all as specified and directed.

M&L for for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

S&F Aluminium anodised tubular tower rail, 20 mm dia fixed between brackets

S&F Aluminium anodised brackets for 20mm dia tower rail.

Dismantling floor , hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles and removing debris and depositing complete all as specified and as directed.

M&L Glazed ceramic coloured tiles, of size 300x200x7mm/400x200x7mm thick on vertical surfaces such as skirtinh/dado/risers etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment match the colour of tiles with and incl 10mm thick backing coat in CM 1:4.

M&L for Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,

M&L for PCC B2 type (1:2:4) using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S 1161-1979 grade St.-240 all as specified and directed.

S&F MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of Fe-410- W(Gde- E-250) quality all as specified and directed.

S&F Mild steel bolts, purpose made, with hexagonal / square head one end & screwed the other/ screwed both ends; each screwed end to be fitted with washers & one hexagonal or square nut, exc 30cm long dia of neck exc 12 but n exc 20 mm all as specified and directed.

Applying two coats of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new surface & applying one coat of red oxide, zinc chrome all as specified and directed.

S&F prepainted galvolume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall fixed with self tapping screws as specified.

S&F prepainted galvolume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall fixed with self tapping screws as specified.

M&L PCC type B1 (1:2:4) using 20mm graded aggregate as in in ramps,landing , cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones,bed plates, , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed complete all as specifed

M & L for Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel') as directed complete all as specified and directed.

S & F galvanised security fencing 80mmx80mm with PVC coated mesh made out of 3 mm dia MS wire and 1.5 mm thick PVC coating through out and fixed to angle iron post including binding works complete all as specified and directed

S&F round bars 10 mm dia and over upto and including 10mm dia in stirupps spacers and binders, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including MS wire annealed not less than 0.9 mm dia confirming Fe-410-W (Gde-E-250) quality-A or Fe 290 (Gde-E-165).

S & F for Galvanized, 2 strand, steel barbed wire 2.24 mm dia., barbed with 2 mm dia., barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanized mild steel pins etc including taking down complete all as specified and directed

S & F for MS angle iron Hand rails, including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting hard /dense soil complete all as specified

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out hard/dense siol complete all as specified

M&L for PCC D2 type (1:4:8) using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry in CM 1:3:6 type C1 with solid blocks, exc. 10 cm in width and setting in mortar, complete complete all as specified

Hardcore of guage n.exc 63mm deposited,spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface all as specified

M&L for PCC 100 mm thick type D2 type (1:4:8) using 40 mm graded stone aggregate as in sub base of floor complete all as specified and directed.

M&L for PCC 100 mm thick type B2 type (1:2:4) using 40 mm graded stone aggregate as in floor complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point ® complete all as specified and directed.

M&L for fabricated Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing completecomplete all as specified and directed.

S&F in in repair GI tubes 32mm bore, 'medium grade' galvanised, with all fitting and fixed complete all as directed by Engineer-in-charge and all as specified.

S&F in in repair GI tubes 25mm bore, 'medium grade' galvanised, with all fitting and fixed complete all as directed by Engineer-in-charge and all as specified.

S&F in in repair GI tubes 20mm bore, 'medium grade' galvanised, with all fitting and fixed complete all as directed by Engineer-in-charge and all as specified.

S&F in repair Stop valves 25 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions all as specified and directed.

M&L for cutting existing steel tubing for alterations or additional each cut measured 25mm to 32 mm complete all as specified and directed.

Rotational moulded polyethylene water storage tanks 2000 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

M&L for Stop valves, 25 mm diacast copper alloy, screwed down, high pressure, with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixedcomplete all as specified and directed.

M&L for Ball brass valves,25 mm dia high pressure,with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixedcomplete all as specified and directed.

M&L for Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed 20 mm dia complete all as specified and directed.

S&F aluminum louvers with levers and locking arrangements suitable for fixing 100mm wide 4 to 6 nos glass complete all as specified and directed.

S&F for 30mm thick flush shutter factory made solid core construction with partical board core and plywood face panels commercial type on both sides complete all as specified and directed.

Dinesh Enterprises

INDIA ENGINEERS AND CONTRACTORS

M/s S.D Construction Co

M/s Vishwakarma Enterprises