REPAIRS TO FENCING PCC PATH HARD STANDING DRAIN AND OTHER MISC WORKS AT RANGE HILLS AREA UNDER GE MH AND RH KIRKEE

Amount

Demolition of brick work, PCC block mansonry or stone boulder masonary built in cement mortar including all quoins arches pillars etc. but excluding ashlar facing dressed stone work and precast concrete articles.

M&L for Pre-cast cement concrete block masonry of PCC 1:3:6 Type C1 using 20mm graded stone aggregate with solid blocks straight or curved on plan , exc 6m mean radius and exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

All as per item No 2 above but except block recovered from demolition shall be reused complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls,ceilings etc. including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement morter 1:4 complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

M&L for preparation of old plastered surfaces of wall and applying one coat of cement base paint including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and as directed.

Dismantling fencing, wire mesh any type complete all as specified and directed by Engr in Charge

Dismantling of RCC post or struts carefully of any section embedded in concrete incl taking out embedded portion and making good disturbed ground incl taking down/out worn out unserviceable old barbed wire, chain link fencing complete.

Excavation in post hole each n.exc 0.50 Cum getting out returning filling in and ramming earth around in layers n.exc 25cm watering and removed surplus soil to a distance n.exc 50m in soft/loose soil.

S & F MS angle iron in fencing posts & struts including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets ( for securing wire mesh etc) including all necessary, drilling, bolting or riveting etc and similar work conforming to Fe-410-0 or Fe-310-0.

M & L for cement concrete M-10 grade (Nominal Mix) using 40 mm nominal size graded crushed stone aggregate in foundation, filling and mass concrete for fencing post complete all as specified and as directed.

Supply only Chain link MS galvanised fencing, any size or type complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

S & F galvanized steel barbed wire with two strands of line wire of dia 2.24 mm and barbed with point wire of dia 2 mm at 75 mm spacing straining and fixing to any type of standards, rails, straining bolts including securing or tying at crossings with and provision of galvanised iron binding wire, GI staples or steel pins, etc. complete all as specified and as directed . Note : Two strand of line wire will be measured as one unit length.

Restraining & rescuring including making good staples etc. galvanized steel barbed wire with two strands of line wire of dia 2.24 mm and barbed with point wire of dia 2 mm at 75 mm spacing straining and fixing to any type of standards, rails, straining bolts including securing or tying at crossings with and provision of galvanised iron binding wire, GI staples or steel pins, etc. complete all as specified and as directed. Note : Two strand of line wire will be measured as one unit length.

S & F hot rolled medium and high tensile structural steel of grade E165 as per IS 15911: 2010 as in framed work such as grills, grating, etc., with ends of bars of shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework water tanks and similar work complete all as specified and directed by Engineer-in-charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc.

S & F for steel work of grade-3 as per IS 10748 in tubular trusses including special shaped washer etc. complete using ERW or HRIW welded tubes conforming to IS 1161: 2014 (Yst 240 Grade) complete all as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering fixed with self tapping screws including dismantling old roof sheet of CGI/PGI complete all as specified..

S & F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in cladding to wall, fixed with self tapping screws including dismantling old roof sheet of CGI/PGI complete all as specified.

M&L for preparation of untreated new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint ( 1st grade quality ) over a coat of red oxide primer complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removing the same off the premises complete all as specified and directed.

M&L for 75mm thick Cement concrete M-7.5 grade (nominal mix) using 40mm graded stone aggregate as in sub base floor and paving etc all as specified

M&L for sand/ stone dust filling under floors including consolidation for laying paver block all as specified (Thickness of cushion should not be less than 25mm).

M&L for 80mm thick coloured rubburised, glossy finish colour machine pressed interlocking pattern paver block any shape and size conforming to IS 15658-2006 of M-40 Grade all as specified and directed by Engineer-in Charge.

M&L Chequred Cement concrete coloured tiles 30 cm x 30 cm x 20 mm thick, glossy finished set jointed and pointed in neat cement slurry in floors, and cut and polished with grey cement and pigments laid over & including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

M&L for 75mm thick PCC M-10 grade (nominal mix) using 40mm graded stone aggregate as in plinth protection/path finishing cement concrete surface even and smooth without using extra cement complete.

M& for Forming Contraction (Dummy) joints 75 mm deep x 10mm wide, filled with sealing compound complete all as specified and directed by EIC.

S & F in repair, 75mm thick PVC (SWR) pipes Type 'A' single socketed, in any length with rubber ring joints laid in floor.

M&L Cement concrete M-15 grade (nominal mix) 20mm graded stone aggregate in surface channels and drains all as specified

Extra for fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/stopped ends etc.

Demolition of cement concrete reinforced (reinforcement cut as required to facilitate demolition) in roof floors, beams, staircase, landings, chajjas, pillars etc and similar suspended works and removing materials from site of work complete all as directed.

M & L for precast cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces fair faces, including chamfers, weatherings, throating etc. and setting in cement mortar 1:4 complete with joints to match complete all as specified and as directed.

S&F TMT bars 6 to 8mm dia bar, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips.

M&L for RCC M-25 (design mix) in columns, pillars, piers, posts and struts all as specified

M&L for RCC design mix M-25 grade, using 20 mm graded stone aggregate as in Beams, cantilevers, bressummers, lintels & similar RCC works all as specified and directed.

M & L for steel formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete complete all as specified and as directed.

M & L for steel formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete complete all as specified and as directed.

S&F of Mild TMT steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips Fe-410-W (Gde.E-250).

All as per item No 41 above, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar

M&L Coloured Glazed ceramic tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm / 450 x 300 x 7mm thick, on vertical surfaces such as skirting, dados etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 10mm thick rendering as in backing coat in CM 1:4 complete all as specified and directed.

M&L for 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete fixed over and including backing coat of 10mm thickin CM 1:4 all as specified

MANIYA CONSTRUCTION CO

SAMBHAJI D JARANDE

MAHESH DADAJI BACHHAV

Shri Sant Cosntruction

Aishwarya Constructions

S.R.M.K Enterprises

V.R.PRAJAPATI AND CO.

M/S JAYCONSTRUCTION CO