SPECIAL REPAIR/REPLACEMENT OF FALSE CEILING AND ALLIED WORK INCLUDING COMPOSITE PANEL, SIGNAGE BOARDS AND FLOOR WORK AT GUARD STAND AND IMPROVEMENT AND RENOVATION OF FIELD MESS AT CHANDHAN UNDER GE AF JAISALMER

Amount

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantling asbestos cement, plain or corrugated sheeting, any gauge, thickness, complete all as specified and directed.

Anodized aluminium snap grid frame work for false ceiling as per manufacturer's instructions with hangers from RCC soffit/steel trusses with 6mm dia GI rod (upto 1200mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long with including 12mm thick mineral fibre decorated board of size 600mmx 600mm fixed in aluminium snap grid, fixed with screws to timber frame work or with staples on snap grid in ceiling, flat or sloping and including dismantling and taking down old unserviceable existing ceiling complete all as specified and directed. Note :-(i) Ceiling board to the ceiling grid by Silicone sealant of 500 gm pack shall be included in quoted rate . (ii) Ceiling board to the ceiling grid by araldite of 500 gm pack shall be included in quoted rate.

Demolition of plain cement concrete (unreinforced) as in ground floors, copings and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

25mm thick Plain Cement Concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in levelling coarse in flooring, finished even and rough complete all as specified and directed.

Precast cement concrete (1:3:6), type C-1 (using 20mm graded stone aggregate) as solid block masonary exceeding 10cm and set in cement and sand mortar (1:4) including demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed.

Plain cement concrete (1:3:6) typeD-2 using 40 mm graded stone aggregate as in mass filling and foundation complete, all as specified and as directed

PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base of flooring finishing cement concrete surface fair and even in any thickness complete all as specified and directed.

10mm thick, size 300x300mm coloured endura parking tiles over and including 15mm thick screed bed in cement and sand mortar 1:6 and including dismantling floor, hearth or wall tiling including cement mortar bedding complete all as specified and directed

Vitrified ceramic tiles 10mm thick (square/rectangular), polished, coloured (light shade double charged as approved), area of each tile exceeding 0.42 sqm not exceeding 1.0 sqm,as in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 15mm thick screed bed in cement and sand mortar 1:6 including dismantling of floor, hearth or wall tiling with cement mortar bedding complete all as specified

Vitrified ceramic tiles double charged 10mm thick (square/rectangular), polished, coloured (light shade as approved) on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with wall tiles over & including 10mm thick screed bed in cement & sand mortar 1:4 and including dismantling of tiling with cement mortar bedding complete all as specified and directed.

12mm thick plain/froasted toughened glass door including stainless steel door handle 300mm long decorative type incl all necessary connected fittings and fixtures for door fixed in as repair complete all as specified and directed

Double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty, with & including replacement of floor tiles if any broken during repair work and making good surfaces matching to the existing surfaces complete all as specified and directed.

12mm thick plain / froasted toughned glass with aluminium frame supplied and fixed at site in aluminium snap bedding fittings for glass fixed in as repair complete all as specified and directed

Tinted/froasted film over toughned glass with Airforce logo complete all as specified and directed

Powder coating Aluminum anodised section frame work for chowkats /doors / windows shutters with style and rails or for fixed glazed partition wall frame made to shape required fixed with 150mm long screw and rawl plug incl necessary joining cleats,glazing clips,rubber packing ,anodised aluminium snap beading ,screws etc complet all as specified and directed.

200mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

Aluminium handle 150mm long , fabricated type anodized complete all as specified and directed.

Mortice lock vertical type , size 100 mm bright finished brass with four levers and pair of anodized (anodic coating 10 micron) as per IS-1868) aluminium lever handles with necessary screws etc complete all as specified and as directed

Aluminium extruded section body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851-1000mm in width & weight between 61 to 80 Kg, complete all as specified and directed.

Floor door stopper of of 140 mm length of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

150mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

100mm Butt hinges, medium weight, cold rolled mild steel (ISI marked) complete all as specified and directed.

PVC connection suitable for 15mm bore with PTMT nuts of 600mm length and fixed as in repair complete all as specified and directed.

Galvanized steel water tubing medium grade of 15mm bore with & including all fittings fixed to walls and ceiling or laid in floors, including taking up or down old unserviceable steel water tubing , complete all as specified and directed.

Galvanized steel water tubing medium grade of 20mm bore with & including all fittings fixed to walls and ceiling or laid in floors, including taking up or down old unserviceable steel water tubing , complete all as specified and directed.

Stainless steel Curtain rod 25mm dia with side bracket fixed with stainless steel matching pair of brackets fixed at both ends with screws on walls/beam complete all as specified and directed.

Rotational moulded polyethylene water storage tanks 500 Litre capacity triple layer (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. fixed with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwed for iron pipe 20mm bore including dismantling of existing water tank complete all as specified and directed.

Rotational moulded polyethylene water storage tanks 1000 Litre capacity triple layer (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. fixed with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwed for iron pipe 20mm bore including dismantling of existing water tank complete all as specified and directed.

15mm bore chromium plated bib taps, fency type, long body with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed as in repairs complete all as specified and directed. .Make ;-Jaguar Cat No CON-053KN or other equivalent approvrd make.

15mm bore brass chromium plated angle valve/stop valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed as in repair complete all as specified and directed .Make ;-Jaguar Cat No CON-053KN or other equivalent approvrd make.

Tubular towel rack, brass chromium plated, 20mm dia, ‘D’ type, 60cm long fixed with steel screw fixed as in repair complete all as specified and directed .Make ;-Jaguar Cat No AQN-7781A 600mm long or other equivalent approvrd make.

Toilet paper holder, brass chromium plated, fixed as in repair complete all as specified and directed . Make ;-Jaguar Cat No AKB-35751 or other equivalent approvrd make.

Soap dish holder fixed as in repair complete all as specified and directed. Make ;-Jaguar Cat No AQN 7731 or other equivalent approvrd make.

Chromium plated Hand Shower (Health Faucet) with 1.0 to 1.50 metre long flexible tube & wall hook and anodised hanging device fixed as in repair complete. Make Jaguar or other equivalent approved make.

CP corner fixed as in repair complete all as specified and directed. Make Jaguar or other equivalent approved make.

CP Grating 150mm size (minimum weight 100gm) fixed as in repair complete all as specified and directed.

Vitreous china wash down water closet pan (Pedestal pattern), white coloured, including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc., with plastic water closet seat cover (white coloured) closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device fixed as in repair complete all as specified and directed.Make .JAQUAR Cat No SLS-WHT-6851S110PP or other equivalent approvred make.

Coloured TABLE TOP wash hand basin with built up with cabinet with stainless steel brackets fixed as in repair complete all as specified and directed Make Jaquar Cat No SLS-WHT-6901 or other equivalent approvred make.

Prepariation of newly steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of old painted steel surfaces over 10cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Refixing of loose/broken flat iron side clamps of rolling shutter to any type of wall pillar etc. with and including flat iron,necessary welding work with stainless steel fasteners complete all as specified and directed.

Gear box assembly for rolling shutter incl rod , required nuts, bolts, cleats,crank handle etc. Complete of standared make and fixed in position incl one coat of primer and removal of old gear box assembly and other accessories fixed as in repair complete all as specified and directed

18mm to 20mm thick granite stone (of any type) machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over and including 15mm thick screed bed in cement and sand mortar 1:6 screed bed includingpointing to match in CM 1:2 using marble dust with admixture of pigment including grinding and polishing complete all as specified and directed.

Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete all as specified and as directed.

9mm thick plywood, grade BWR, type BB, fixed with screws, nut, bolts to timber or metal frame work, frequency of fixing of plywood as per operational requirement complete all as specified and as directed.

Flex glow sign air force monogram including sticking / paste by pressure application of rubber cement on slant surface in three or more pieces including care to match the photo of monogram without any depression / including 03 Nos monogram of required size same as per sample existingcomplete all as specified and as directed.

Second class hard wood Plain fillets. square, rectangular or triangular in section, clean sawn, se-cured with nails or brads of section exc 13 & n. exc 25 sq.cm and fix to wall with rewal plug and suitable steel screws complete all as specified and as directed.

Preparation of old concrete/stone slant surface and letter writting 60 cm wide and applying two coats of synthetic enamel paint of any tint etc complete all as specified and directed.

Acrylic sheet composite panel 8 mm thick of any shape & size fixed to existing aluminium/steel / acrylic / wooden frame with screws and appropriate fittings & fixtures with flex sign Air Force monogram incl required text as sample kept in chandhan incl sticking/paste etc. including dismontling of existing complete all as specified and directed.

Acrylic sheet 8 mm thick of any shape and size up 1 sqm fixed to existing aluminium /steel/acrylic/wooden frame with screws and appropriate fittings & fixtures with flex glow sign airforce monogram including required taxt as semple kept in chandhan including sticking/ paste by pressure application including care to match the photo of monogram without any depreesion / undulation 6 Nos of monogram complete all as specified and directed.

Writting of letters ,dashes and directional arrows etc. Made with 8 mm thick acrylic sheet and size of each letter /arrows/dash shall be approx 0.60m high and 0.45m width fixed to existing aluminium /steel/acrylic/wooden frame with screw and appropriate fitting and fixtures with flux glow computerised (light) cut of high intensity of letters such as ex-VAYUSHAKTI 2024 or same as per sample kept in chandhan including sticking /paste by pressure application including on acrylic sheet care to match the photo of monogram without any depression /undulation complete all as specified and directed.

VAYU SHAKTI Emblem having 4mm thick PVC sheet dia 60 cm with flux glow sign incl brackets of FI 20mmX3mm for electric pole approx 100 to 150mm dia all as specified and directed.

Double legged informatory sign board of size 1.20 M X 1.20 M fixed on single frame , both side and meeting back to back stainless steel 50mm square pipe . The board are of high intensity grade retro-reflective sheeting of AVERY DENNISOX made out of 2 mm thick alcoband sheet / aluminium sheet confirming to IS 736 , colour as approved by Engr-in-Charge on stainless steel square pipe of size 45 X 45 X 3.65 mm or of round pipe 50 mm dia of thickness 3.65mm with nut and bolt . The letter writing will be computerised cut of high intensity grade white sheeting (AVERY DENNISION) and mechanically fixed on board over vertical post of 50mm stainless steel square pipe, 3.65mm thick 2.0 to 3.0 M long having 2 Nos flat stainless steel strip of strip 40X5mm 0.3 m long on bottom and fixed with PCC 1:2:4 in post holes.complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but not exc 4 sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 sq. m and n exc 2 sq. m each complete all as specified and as directed

Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work confirming to Fe-410W Grade E-165 complete all as specified and directed.

Factory made 35mm thick second class hard wood plain framed, paneled shutter (Two panels) with lock rail and panel of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces, size of rail and styles as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated using second class hard wood rail and styles, fixed to chowkat, complete all as specified and directed.

Factory made Second class hard wood 35mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares with plain chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or founded, fitted with cut and mitred beads for securing glass or wire cloth any number, etc sizes of members of shutter as specified in SSR Part-I complete all as specified and directed.

3.0 mm thick plain glass pin head type and glazing with oil putty in squares n.exc 0.50 sqm each including hacking out old broken glass complete all as specified and as directed

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture1.4mm and fixed with stainless steel wire staple fixed with aluminium beading etc complete all as specified and as directed.

Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture1.4mm and fixed with stainless steel wire staple fixed with aluminium beading etc fixed as in repair complete all as specified and as directed.

2 nd class Hard wood beading straight ( any size ) for glazed or gauzed joinery , renewed , including mitres etc, and removing old beeding. fixed as in repair complete all as specified and as directed.

250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

MS Door spring (Capsule type ) 150mm long and including roller and roller plate complete ll as specified and directed.

Preparation of old painted wooden surfaces of any description exceeding 10cm width or girth and applying one coat of synthetic enamel paint of any tint etc complete all as specified and directed.

Preparation of newly surfaces of wood or wood based material of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified and directed.

Prepariation of newly steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

15mm thick plaster in cement mortar (1:6) on internal wall surfaces finished even & smooth, without using extra cement including taking down old plaster complete all as specified and directed.

15mm thick plaster in cement mortar (1:4) on external wall surface finished even & fair without using extra cement including taking down old plaster complete all as specified and directed.

5mm thick ceiling plaster in cement mortar (1:3) on uneven faces of concrete surfaces of ceiling soffits of chajjas/ drop & roof projectiom facia etc , including taking down old plaster complete all as specified and directed.

Preparation of old plastered surfaces of walls of any storeys/any height of any description and applying one coat of oil bound distemper approved shade/tint after removal of existing treatment by washing, rubbing down and stopping of painted surface complete all as specified and as directed .

Preparation of new plastered surface of any description and applying two coats of oil emulsion distemper including chalk whitening preparatory to distempering of wall as approved etc complete all as specified and directed.

Preparation of new plastered surfaces of ceilings of any description and applying two coat of white wash complete all as specified and directed.

Preparation of old plastered wall surfaces and applying one coat of cement based paint (tinted) as approved complete all as specified and directed.

Preparation of old surface ( plastered or un plastered ) of wall including cornices, pilasters etc any storeys/any height of any description including brooming or steel wire brushing, scrapping down smoke soot mould, moss and efflorescent salt and trading oil and greasy spot and applying two coats of white wash complete all as specified and directed.

Coloured ceramic tiles 7 to 8mm thick(square / rectangular ) Anti skid area of each tile exceeding 0.06sqm and n exc 0.16 sqm , in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over 15 mm thick screed bed in cm 1:6 etcncluding dismantling of floor, hearth or wall tiling with cement mortar bedding complete all as specified and directed.

Glazed colouredceramic tiles in dado/skirting 300x450x6-7mm on vertical surfaces, over and including 10mm thick cement and sand mortar (1:4) backing coat set and jointed in neat cement slurry and pointed in coloured cement to match the colour of tile and including dismantling of existing tiling with cement mortar bedding complete all as specified and directed

Machine cut Kota stone slab 18- 20mm thick, as in floor, riser of step, etc. laid over and including rendering of 15mm thick in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including dismantling of existing stone slab complete all as specified and directed.

Machine cut Kota stone slab 18- 20mm thick, as in skirting,, dado and pillar etc. laid over and including rendering of 10mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including dismantling of existing stone slab complete all as specified and directed.

Rounding to edges of stone slabs one edge such as in steps,cooking platform,and other similer situations complete all as specified and as directed.

Reinforced cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) as in wash basin counter slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and removing the debries from site complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) including edges for rough-finished surfaces of concrete flat complete all as specified and directed.

Counter wash basin Oval shape of size (560x450)mm white colour excluding taps, complete all as specified and as directed. Make;-ZEN-10049 or other approved Equivalent Make.

PVC connection suitable for 15mm bore with PTMT nuts of 600mm length and fixed as in repair complete all as specified and directed.

15mm bore brass chromium plated, fancy type, angle cock/stop valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed as in repair complete all as specified and directed.

15mm bore bib tap cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fixed as in repair complete all as specified and directed.

15mm bore pillar tap cast copper alloy chromium plated screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screw shanks screwed for iron pipe or union fixed as in repair complete all as specified and as directed.

Tubular towel rail, stainless steel, 20mm dia, 60cm long fixed with & incl chromium plated brass screws and wooden / plastic cleat fixed as in repair complete all as specified and directed.

Curtain rod 25mm dia, stainless steel with fixing fancy brackets, stops, rollers fixed as in repair etccomplete all as specified and directed.

Sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm with all fitting and fixure fixed as in repair complete all as specified and directed.

32/40mm bore spring type, PVC flexible down take waste pipe fixed to WHB, urinal or sink fixed as in repair complete all as specified and directed.

5.5mm thick bevelled edge looking mirror with required steel screw fixed as in repair complete all as specified and directed.

20mm dia Gun metal globe or gate valve, with iron wheel head, screwed both ends, ISI marked fixed as in repair line complete all as specified and directed.

75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches/floor fixed as in repair complete all as specified and directed.

PVC (SWR) floor trap 75mm dia outlet plain with grating including jointing with solvent cement for trap fixed as in repair complete all as specified and directed.

PVC(SWR) gully trap 125/110mm setting and jointing with solvent cement fixed including demolition of existing traps complete all as specified and directed.

75mm bore PVC (SWR) bend any radiusany radius with access door fixed as in repair complete all as specified and directed.

75mm bore PVC (SWR) bend any radius fixed as in repair complete all as specified and directed.

110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or laid in trenches/floor fixed as in repair complete all as specified and directed.

110mm bore PVC (SWR) bend any radius fixed as in repair complete all as specified and directed.

110mm bore PVC (SWR) Junction Single (Single T) equal or unequal provided with access door fixed as in repair complete all as specified and directed.

110mm bore PVC (SWR) vent cowl fixed complete all as specified and directed.

Hardcore of guage not exceeding 63mm deposited spread and leveled in layers not exceeding 15cm thick watered and rammed to a true surface complete all as specified and directed.

75mm thick Plain Cement Concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in plinth protection and flooring and provided joints 10mm wide & full depth at 3m distance and every change of direction filled with sand and bituminious mix 1:3 including demolition of existing concrete and removal debris outside MD land complete all as specified and directed.

Taking down carefully existing unserviceable/perished conduit/ batten/ casing caping aluminium/copper point wiring any type for light, fan, bell, socket, power point etc complete including all fixtures and fittings such as batten/ conduit/casing caping, switches, sockets, ceiling rose, pendent holder, lamp holders, bracket holders, light fittings, top sheet covers, fan regulators etc and making good the disturbed surfaces of wall/ceiling complete all as specified & directed.

Point wiring for one light point/ fan point controlled by one, one way switch with 1.50 sqmm PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke & Halogen (FRLSH) cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke & Halogen (FRLSH) cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including PVC casing caping with accessories fixed to cutting chases in walls by cutter and making good the surface in cement and sand mortar 1:3 and to the original specification and PVC conduit on ceiling for steel structure/surfaces conduit with clamps, gutties etc for RCC ceiling with including cast iron/pressed steel/wooden terminal boxes (as per site requirement) including providing new 3 mm thick plastic laminated sheet cover (Hylem) complete all as specified and directed.

All as per serial item No. 110.00 here-in-before but for one 3 Pin, 5/6 Amps, socket outlet controlled by one 5/6 Amps switch on independent board complete all as specified and directed.

All as per serial item No. 110.00 here-in-before but for one 3 Pin, 5/6 Amps, socket outlet controlled by one 5/6 Amps switch on same board complete all as specified and directed.

Point wiring for one 6 Pin, 15/16 Amps socket outlet controlled by one switch on independent board with 4 Sqmm single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke & Halogen (FRLSH) cable 1100 volt grade including 4 Sqmm single core PVC insulated and unsheathed multistranded copper conductor Flame Retardant Low Smoke & Halogen (FRLSH) cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including PVC casing & caping with accessories fixed on surface of walls/ceiling by means of PVC sleeves/dash fasteners with cadmium plated screws, all as per IS, terminated & including suitable size module boxes for housing of modular switches, sockets, regulators complete all as specified and directed. Note : (i) Unit rates quoted by contractor shall be deemed to included for cutting chases in walls, ceilings and making good surfaces in cement and sand mortar (1:3) and finishing the surfaces to match with existing surfaces. (Make : Hylem/Anchor including machine screws and washer etc for fixing switches sockets etc including 4 sqmm copper conductor, standard (green colour earth), PVC insulated unsheathed earth wire to commen earth and connected to earth dolly as specified and directed.

Modular switch 6 Amps, 240 Volt, AC, one way, one module (ISI Marked) fixed as in repair complete all as specified and directed.

Modular switch 16 Amps, 240 Volt, Single Pole, AC, one way with indicator one module (ISI Marked) fixed as in repair complete all as specified and directed.

Modular Socket shuttered, 6 Amps, 250 volts, 2/3 Pin combined, Single Pole, universal India two module (ISI Marked) fixed as in repair complete all as specified and directed.

Modular Socket shuttered, 6/16 Amps, 240 volts, 3 Pin combined, Single Pole, two module (ISI Marked) fixed as in repair complete all as specified and directed.

Modular Fan Regulator, step type, 120 Watt, 2 module, 240 volts grade, (ISI Marked) fixed as in repair complete all as specified and directed.

MCB Protected Socket (Modular AC Box, Metal clad box) Two Module, Single Pole, 20 Amps, repturing capacity 10 kA and neutral enclosure in sheet steel with a two pin and earth plug and socket including taking down old unserviceable complete all as specified and directed.

White colour modular blanking plate, one module blank fixed as in repair complete all as specified and directed.

Ceiling rose, surface Bakelite 65 x 17.50 mm of three terminals PVC/Polycarbonate,isolated body fixed as in repair complete all as specified and as directed.

LED Bulk head fitting 10 watt in engineering plastic housing with clear prismatic diffuser cat part No LBHP-10-CDL of make : CG or equivalent in Syska/Philips/Bajaj including LED 10 watt complete with all accessories and connecting up complete with 3 core flexible cable white of size 23/0.0076 including taking down old unserviceable bulk head fitting complete all as specified and directed.

Sub main wiring with 6.00 sqmm, two single core, PVC insulated unsheathed multistranded copper conductor FRLS 1100 volts grade conforming to IS 694 including and 6.00 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour including drawn through in 25mm dia PVC conduit incl taking existing complete all as specified and directed. Note : Two run of 6.00 sqmm cable and one run of 6.00 sqmm cable as earth wire continuity conductor and one run 25mm dia PVC conduit shall be measured & paid as one unit (running metre).

Sub main wiring with 4.00 sqmm, two single core, PVC insulated unsheathed multistranded copper conductor FRLS 1100 volts grade conforming to IS 694 including and 4.00 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour including drawn through in 25mm dia PVC conduit incl taking existing complete all as specified and directed. Note : Two run of 4.00 sqmm cable and one run of 4.00 sqmm cable as earth wire continuity conductor and one run 25mm dia PVC conduit shall be measured & paid as one unit (running metre).

LED tube light fittings of cap 10W , Two feet basic all purpose surface and wall mounted LED batten with extruded aluminium housing & integrated electronic driver with all including taking down old unserviceable LED complete all as specified and directed

LED tube light fittings of cap 20W , four feet Basic all purpose surface and wall mounted LED batten with extruded aluminium housing & integrated electronic driver with all including taking down old unserviceable LED complete all as specified and directed .

Sheet metal enclosure powder coated single phase DB SPN 8 ways (2 +6way) and neutral 240 Volts, AC supply, 50 Hz, with 200 Amps rated bus bar Double Door (IP-43 IK 09 with metal door) suitable for fixing of MCBs including fixing of lugs in main incomming and outgoing line and fixing of cable glands of suitable size including grouting flush in the wall by means of nuts, bolts, angle iron and making good disturbed surfaces including taking down old unserviceable DB complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of plate not less than 1.5 deep below normal ground level and connected to and including galvanized earth lead wire 4mm dia upto 7.5 metre by means of GI nuts, bolt, check nuts, washers thimbles, etc as shown in electrical plate No 03 SSR Part I and connection to main switch board or panel and testing on completion including excavation and earth work in any type to soil, returning fitting in and removal of surface spoil to a distance not exc 50 metre, PCC chamber (1:3:6) type C-2, charcoal and salt mixed layer 15cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe light grade 20mm bore for watering and 15mm bore meter long GI pipe light grade for earth wire protection fixed with poles with two clamps, made from MS flat 25mm x 3mm, bolts, nuts and washers 75mm thick RCC cover 1:2:4 type B-1 shall be provided on CI frame etc complete all as specified. Note - (i) PCC chamber shall be constructed at least 1.5m away from the earth electrode. The pipe for watering shall be provided in slanting manner. The cost of 7.50m GI pipe for protection of earth wire/strip .(ii) Quoted amount deemed to include the cost of excavation /earthwork , PCC pit , funnel , cover GI medium grade protectiom pipe.

Ceiling Fan 1200mm sweep, BLDC (Brush less direct current), min air delevery 210 CFM with service value 6.00 BEE,five star rated ,single phase, AC supply, 240 Volt, including canopies, three number blades, down rod, double ball bearing with capacitor of 2.5 mfd, and including PVC insulated PVC sheathed copper conductor flexible cable 3 core of suitable size from ceiling rose or connector to fan including marking of MES number and taking down old unsv fan and deposited to MES store complete all as specified and directed.

Exhaust fan, PVC body,AC single phase 230V of size 250mm sweep with blades and frames and louvers including making holes in to the wall as per fan size and making good the disturved surfaces complete all as specified and directed.

Wall Mounted fan of 400mm 240 volt 70 cubic per minute air delivery and 1350 RPM including making holes in to the wall as per fan size and making good the disturved surfaces complete all as specified and directed.

Cygnus series Recess mounting LED 36watt/40 watt 2' x 2' LED Slim Panel - 595x595 mm cat Part No CCR-126-50-40-SL-NWH of make- CG electric or equivalent in Philips/Havells/CG/Bajaj white powder coated aluminium extruded housing with LEDs including LED driver and fixing in recess ceiling suitable size of aluminium strip size as required for fixing of LED fitting complete with all accessories prewired fixed on ceiling and connecting up complete with 3 core flexible cable of size 23 / 0.0076 including taking down old unserviceable fitting complete all as specified and directed.

Electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc as specified and directed

Electric water heater,instant flow type and heating element upto 3 KW, 3L capacity, 230 V BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc as specified and directed

Sheet metal enclosure for VPTN DBs 4 way , double door, (IP-43) built in bus bars complete suitable for 415 Volts AC, 50 Hz , supply , suitable for incoming MCCB and outgoing MCBs and fixed in recess in brick masonary wall complete all as specified and directed.

MCB, Single Pole, 6 to 32 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA, 240 Volt grade, AC supply, 50 Hz and making connections using suitable size copper lugs/thimbles including complete, all as specified & directed.

MCB, SPN, 32 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA, 240 Volt grade, AC supply, 50 Hz and making connections using suitable size copper lugs/thimbles, including disconnecting & taking down old unserviceable MCB, complete all as specified & directed.

MCB, TPN, 63 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA, 415 Volt grade, AC supply, 50 Hz and making connections using suitable size copper lugs/thimbles, including disconnecting & taking down old unserviceable MCB, complete all as specified & directed.

M/s Ramesh & Company

M/s Fateh Enterprises

S K TRADER

AMBEY MAA CONSTRUCTION COMPANY