Provn of toilet block near MH-1A and Provn of hard standing in front of Bldg No II-12 of 122 Inf Bn TA (MADRAS) at Mily Station Calicut under AGE (I) Cannanore.

Amount

Earth work in excavation in soft/disintegerated rock by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m complete all as specified and directed.

M & L for plain cement concrete (1:4:8), type D2 using 40 mm graded stone aggregate as in foundation of building, pole, strut, stay etc all as specified and directed.

Returning and filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with soil obtained from excavation all as directed

Removing surplus excavated materials (rock) not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, exc.10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:6) complete all as specified and directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, n exc.10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:6) complete all as specified and directed.

M&L damp proof course in cement concrete 1:2:4, type B0, (using 12.5mm graded stone aggregate) 25mm thick including necessary form work all as specified and directed.

M&L Reinforced cement concrete (1:2:4), type B1, (using 20mm graded stone aggregate) nominal mix as in beams, lintel over 1.5m span all as specified and directed. Note : Reinforcement and form work shall be measured and paid separately.

M&L Reinforced cement concrete (1:2:4), type B1, (using 20mm graded stone aggregate) as in roof slabs supported on walls, beam etc all as specified and directed. Note : Reinforcement and form work shall be measured and paid separately.

M&L for use and waste of form work to soffits of suspended slabs such as roof slabs and similar work, not exceeding 200 mm thick (horizontal or sloping ), rough finished surface of concrete flat all as specified and directed.

M&L for use and waste of form work to sides and soffits of lintel, beams etc rough finished surface of concrete all as specified and directed.

M&L Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide rough finished surface of concrete flat all as specified and directed.

S&F TMT bars 10 mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips all as specified and directed.

All as per Sl item No 13 above, but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders all as specified and directed.

S & F Powder coated aluminium (minimum thickness of powder coating shall be 50 micron) frame work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P.brass/stainless steel screws, all complete as per the directions of Engineer-in-Charge.

S&F powder coated aluminium side hung window and ventilator shutters without sash bars, anodized of approved colour with aluminium sections weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as suitable hinges, handles 1 Nos in each shutter, side lock, complete all as specified and directed. Note:- Thickness of powder coating shall not be less than 50 micron.

M&L solid PVC door frame of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, all as specified and directed.

S&F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain coloured PVC “C” channel having a PVC sheet strip of 20mm width stock inside with solvent cement for stiles and plain colour PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rail & bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour of PVC sheet fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement etc. Details as peer specification and drawings and all as directed.

M&L for rendering 15mm thick in cement mortar (1:6) on brick or concrete surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 10 mm thick in cement mortar (1:3) on concrete surface of ceiling, finished even and smooth without using extra cement all as specified and directed.

M&L for rendering in 5mm thick plaster in cement mortar 1:4 mixed with integral water proofing compound @ 3% by weight of cement over 10mm thick plaster in cement mortar 1:6 on brick or concrete surfaces finished even and smooth without using extra cement all as specified and directed. Note:-WPC shall be measured and paid separately.

M&L for rendering 10 mm thick in cement mortar (1:3) on over RCC slab surface finished even and smooth without using extra cement with integral water proofing compound @ 3% by weight of cement all as specified and directed. Note:-WPC shall be measured and paid separately.

Supply only Water proofing compound

M&L for hard core of guage n.exc 63mm broken stone or boulders, deposited, spread and levelled in layers n.exc 10cm thick watered and rammed to a true surface all as specified and directed

M&L for moorum/red bajri filling in floor or paving spread and levelled in layers n.exc 15cm thick watered and rammed to a true surface all as specified and directed

M&L 75mm thick PCC 1:5:10 Type E2 (using 40mm graded stone aggregate) as in sub base of floor and paving including necessary form works all as specified and directed.

M&L for coloured non-skid ceramic tiles, 7-8mm thick, area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match including 20mm thick screed bed or bedding layer in cement mortar (1:4) all as specified and directed.

M&L for coloured glazed ceramic tiles 300x200x7mm thick, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 15 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

S&F 100mm long aluminum anodized barrel tower bolts of extruded section fixed with stainless steel screws all as specified.

S&F stainless steel butt hinges medium weight; 100mm size as per IS 21817 fixed with stainless steel screws all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 100mm size fixed with stainless steel screws all as specified.

S&F 4mm thick plane sheet glass, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane with putty or fixed with beads all as specified and directed.

S&F Vitreous China premium/1st quality Wash down water closet pan, white or ivory (excluding flushing cistern and flush type) pedestal pan and trap including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc complete including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device all as specified and directed.

S&F Vitreous China valveless, syphonic action type flushing cistern low level, 10 Litre capacity, white, with inlet, ball valve, float and handle including low or high density suitable size PVC flush pipe all as specified and directed.

S&F 1000 litres capacity rotational moulded polthylene water storage tanks(cylindrical vertical with closed top) of make Sintex/Polycon/Plasto hoisted and fixed in position all as specified in SSR Part I,2009 and directed.

S&F Vitreous China Wash basin, white, flat back, size 630 x 450 mm, including CI brackets, (but excl. pillar tap) cutting for and pinning in ends of brackets or erecting stand etc complete all as specified and directed.

S&F Soap dish, vitreous China white, approximate size 160 x 160x90 mm all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engineer-in-Charge

S&F tubular towel rail PTMT, 60cm long between flanges fixed to wall with wooden plugs with chromium plated brass screws all as specified and directed.

S&F for 15mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings or in floors etc. all as specified and directed.

S&F for 20mm bore UPVC pipes of pressure rating 10 kgf / cm2, fixed to wall/ceiling or on floor all as specified and directed.

M & L PTMT stop valves , any colour high pressure screwed down, screwed for iron pipe or ferrule and complete all as directed.

Supply and fix PVC connecton 60cm long with PTMT nuts for flush tank, wash basin, etc. all as specified and directed

M&L Cutting and screwing existing steel tubing 20mm bore for alterations or additions (or lengthening screw on pipe to form connector) if necessarily done in position without taking down all as specified and directed.

S&F 15 mm bore bib taps, PTMT any colour (min weight 15-90gms), high pressure screwed for iron pipe or for PVC pipe or for brass ferrule, all as specified and directed.

S&F 15 mm bore pillar tap, PTMT any colour (min weight 110gms), high pressure screwed for iron pipe or for PVC pipe or for brass ferrule, fixed all as specified and directed.

S&F vitreous china bowl urinal flat back white 465 x 355 x 265 mm with grating and union for discharge pipe , providing and fixing plugs, bedding urinals against wall in cement mortar1:2, securing urinals plugs with 60mm long brass screws , pointing around urinal back in cement, fixing flush pipe, grating and union for discharge pipe including M&L of vitreous china bowl urinal partition white 310x700 mm securing urinals plugs with 60mm long brass screws , etc complete all as directed.

S & F urinal spreader of PTMT any colour, 15mm bore (mininmum weight 60gms) complete complete all as specified and as directed.

S&F 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.

M&L for 75mm diameter PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed.

M&L PVC (SWR) pipe type 'B' 75mm bore single socketed with solvent cement joints laid in trenches or in floors all as specified and directed.

M&L PVC (SWR) pipe type 'B' 75mm bore single socketed with rubber ring joints fixed to wall all as specified and directed.

S&F 75 mm bore, PVC (SWR) bends with access door all as specified and directed

M & L for preparation of newly plastered surfaces of wall and applying a coat of wall primer and two coats of oil emulsion distemper and all as specified and as directed.

M&L preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer all as specified and as directed.

S&F ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule of 50mm bore dia all as specified and directed.

M&L Cutting the existing PVC/UPVC tubing 50mm bore and inserting UPVC tee of 50x50x50mm for alterations or additions (or lengthening screw on pipe to form connector) if necessarily done in position without taking down all as specified and directed.

S&F for 50mm bore UPVC pipes of pressure rating 10 kgf / cm2, laid in trenches or on floor all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/dense soil all as specified and directed.

Excavating in trenches n.exc. 1.5m wide and n exc 1.5m depth for foundation, pipe, pole, stay etc and n exc 10sqm on plan and getting out in hard/dense soil all as specified and directed.

Removing surplus excavated materials (soil) exc 250m and not exceeding 500 m and depositing where directed at a level not exceeding 1.5 m above the starting point all as specified and directed.

M&L for Chequered cement concrete coloured tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment including 20mm thick screed bed or bedding layer in cement mortar (1:4) all as specified and directed.

All as per item No 63 here in before but on vertical surfaces including 15 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block approved colour, design and pattern confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment as in foot path, lawn, drive ways etc made by table vibratory method using PU mould, including 60mm thick compacted bed of fine sand compacting and proper embedding, laying of paver block into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand all as specified.

Providing, cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) in coping, rounded or chamfered on edges including necessary form works all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:4) on concrete block masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L Point wiring complete with 1.5 Sq mm single core PVC insulated unsheathed copper conductor FRLS cable multi stranded 1100 Volt grade drawn through and including non metallic rigid PVC conduit, medium grade concealed and fixed to ceiling/roof etc with necessary fixing accessories such as bend elbow socket etc with fixing material including terminal box made out of 1.22mm thick GI sheet concealed in wall covered with bakalite/plastic laminated sheet top cover of 3mm thick cadmium plated screws with cup washer including 1.5Sqmm single core PVC insulated un sheathed copper conductor FRLS cable multi stranded 1100Volt grade as earth continuity conductor green in colour connected to common earth dolly complete all as specified and as directed for One light/fan/bell point controlled by one switch.

S & F switch piano flush type, single pole, one way, 5 Amps, 240 volt including connecting up electrically complete all as specified and as directed.

S & F PVC ceiling rose 65x50mm size, three terminals, polycarbonate, isolated body including connecting up electrically all as specified and as directed.

S & F Decorative ultra slim square profile linear LED light fittings with extruded polycarbonate, heat sink, environmental friendly, energy efficient ready to use pack of 4 feet 20 W LED 6000K, model LHEXBLP7PN1W020 of Havells or equivalent in Syska or Crompton Greaves with all accessoried internally prewired and including connecting up with twin core twisted copper flexible conductor cable of sutibale size all as directed.

S & F MCB SPN, 240 Volt, 63Amps, 10KA, C series, 50Hz, including electrically connecting up using wiring lugs all as specified and directed.

S & F sheet metal enclosure factory made for MCB DB, SPN 4 way with 200 Amps bus bar, 240 Volt, double door type, fixed/flushed on wall including electrically connecting up all as specified and directed.

S&F exhaust fan,mtallic body AC single phase, 230 V of 300mm sweep, BEE 5 star rated with accessories of Havells or CG or Usha including making suiable size hole to wall and finished as per direction complete including connecting up with 2 core twisted flexible copper conductor 23/0.0076 from ceiling rose to fan, testing and commissioning all as specified and directed.

Excavating in trenches n.exc. 1.5m wide and exc 1.5m and n.exc. 3m in depth for laying of LT UG cable, pipe, pole, stay etc and n exc 10sqm on plan and getting out in soft/disintegerated rock all as specified and directed.

M&L for cutting the existing Bituminous / Hard Standing road surface for laying of cable / GI Pipe etc and providing Plain cement concrete (1:2:4) type B2, using 40 mm graded stone aggregate for filling up the area of road cutting surfaces and making good the disturbed surface and all as specified and directed by Engr-in-Charge. Note :- Excavation and earthwork shall be measured and paid separately under respective items.

Supply and spreading in natuaral riddled soil as earth cushioning to cable by using IS sieve to separate the composite particle/roots etc and refilling in trenches and compacted in layers to form a solid bed covering to cable all as specified and directed.

Supply and laying in trenches burnt brick sub class B of locally available size 20x9x6cms for protection of UG cable laid flat and dry over the cable , perpendicular to the direction of cable all as specified and directed.

Supply and laying/fixing and connecting electrically, testing LT underground cable 10 sqmm, 2 Core, XLPE insulated, armoured heavy duty electric cable with aluminium conductor multi-stranded 1100 volts grade, laid in trench, fixed on wall/pole drawn through pipe etc including provision of lugs complete all as specified and directed.

M&L for GI tubing, 50mm bore light grade, galvanized, with all fittings required such as bends, Tees, elbows, sockets etc for protection of cable under road crossing or fixed to wall, complete all as required at site or directed by Engr in Charge.

M&L for LLDPE septic tank conventional type designed to carry sewage for 10 users and sullage water, including excavation in any type of soil, laying PCC 1:4:8, type D2 oundation, laying septic tank and connecting vent shaft, connections to sewer line, returnig, filling, removal of surplus earth etc complete all as required at site or directed by Engr in Charge.

M&L for soak well of size 1.20m internal dia x 3.00m effective depth all as per TD drawing No WD/CAN/02/2022 sh 1/1 as in earth work excavation in hard dense soil, PCC 1:3:6 foundation, honey comb block masonry in CM 1:3, RCC M 30 nominalmix roof slab including form work, steel reinforcement, RCC precast manhole cover laid on angle iron 50x50x5mm frame work fixed in RCC, including rendering, vent pipe, inlet-oulet pipes, MS rungs, brick bat filling around soak well etc complete all as per TD drg and directed by Engineer in charge. Note for item No 81 and 82 : 1) Contractor shall be visited the site before quoting the tender. 2) Excavation shall be in full or partially in hard dense soil or in soft disintegerated rock and quoted rate shall be included for the same. No additinal DOs shall be admissible for the change in strata of earth work.

M&L for Pre-cast RCC (1:2:4) type B1 using 20mm graded stone aggregate as in manhole/drain cover slab etc; set in cement mortar (1:6) all as specified and directed.

S&F TMT bars 8mm dia and over as in reinforcement, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips all as specified and directed.

M&L PVC (SWR) pipe 160mm bore, type 'B' single socketed with solvent cement joints laid in floor or trenches all as specified and directed.

M & L for cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in bed to drain pipe including packing under and haunching against the sides of pipes after they are laided and tested, bore of pipe 160 mm all as specified and directed.

NKS INFRATECH

JEETH CONSTRUCTION