Housing colony under in-situ-slum re-development in convergence with PMAY-(URBAN) as ward no. 13(as per section 13(1)((c) of the Prohibition of Employment as manual scavengers and their Rehabilitation Act, 2013) at North Lakhimpur Town under CIDF

Amount

Earth work in Excavation for Foundations,trenches of walls, retaining walls, footing of columns including refilling (return filling) the quantity as necessary after completion of work, breaking clods and ramming of surplus earth with all lead and lift as directed and specified. (A) Up to a dpeth of 2.0 m below the E.G.L. (a) In ordinary Soil

Providing soling in foundation and under floor at all levels with stone / best quality pickedjhama brick, sand packed and laid to level and in panel after preparing the sub grade as directed including all labour & materials and if necessary dewatering complete. (a) Brick flat soling

Plain cement concrete work with course agg. of size 13mm to 32mm in foundation bed for footing steps, walls, brickwork etc. as directed and specified rewtering if necessary and curing complete. (Shutt ering where necessary shall be measured and paid separately) (a) In proportion 1cem. : 3 Sand. : 6 Agg.

Providing cast in-situ machine driven reinforced cement concrete piles of required bore­ diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings includins using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.4.1) MACHINE DRIVEN PILES- C) UNIFORM PILE (i) Concret garade M2S ii) Pile dia 350 mm

Providing and laying plain & R/F cement conecrete work in prop. M-25, 20mm dowm size including dewatering if necessary and curing complete. but excluding cost of form work and reinforcment for RCC work (form work & reinforcement will be measured separetely) (a) In sub structure upto PL Foundation, footing, colm with base, tie and plinth beam, pile cap, base slab, retaining wall and like and other work not less than 100mm thick upto plinth level. b) M20 grade concrete or Prop. 1:1.5:3

Providing and laying plain & R/F cement conecrete work in prop. M-25, 20mm dowm size including dewatering if necessary and curing complete. but excluding cost of form work and reinforcment for RCC work (form work & reinforcement will be measured separetely) (b) In super structure from Plinth level upto 1st.floor level {ii)Columns,pillers,posts,struts,suspended floor, roof,landing,shelf & suppor,t balcony,lint el,sill band,beam,girder,bressumer,cantilever,stair case including preparing the top surface and finishing of nosing. b) M20 grade concrete or Prop. 1:1.5:3

Providing form work of ordinary timber planking so as to give a rough finish including centering shuttering, strutting & propping etc. height of proping & centering below supporting floor ceilling not exceeding 4.0m and removal of the same for in situ R/F concrete & P.C.C. work. (ii} Using 25mm thick Plank Foundation and footing base of colm.

Providing form work of ordinary timber planking so as to give a rough finish including centering shuttering, strutting & propping etc. height of proping & centering below supporting floor ceilling not exceeding 4.0m and removal of the same for in situ R/F concrete & P.C.C. work. (ii} Using 25mm thick Plank Sides of tie beams,grade beams etc

Providing form work of ordinary timber planking so as to give a rough finish including centering shuttering, strutting & propping etc. height of proping & centering below supporting floor ceilling not exceeding 4.0m and removal of the same for in situ R/F concrete & P.C.C. work. (ii} Using 25mm thick Plank Column,pillars,post and strut (a) square,rectangular,polygonal in plain or any shape..

Providing form work of ordinary timber planking so as to give a rough finish including centering shuttering, strutting & propping etc. height of proping & centering below supporting floor ceilling not exceeding 4.0m and removal of the same for in situ R/F concrete & P.C.C. work. (ii} Using 25mm thick Plank Sides and soffits of beams...for a depth of 1.00m

Providing form work of ordinary timber planking so as to give a rough finish including centering shuttering, strutting & propping etc. height of proping & centering below supporting floor ceilling not exceeding 4.0m and removal of the same for in situ R/F concrete & P.C.C. work. (ii} Using 25mm thick Plank Flat surface roofs,landings balconies etc,

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. (I) In Sub-structure upto plinth level including dewatering if necessary (b) In proportion 1:4

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will bemeasured and paid separately) (A) 112mm thick brick wall (a) In cement mortar in proportion 1:4. (1 cement:4 sand)

10mm thick cement plaster in single coat on fair side of new half brick wall for plastering upto 1st foor level…….. curing complete as directed. (INSIDE OF THE BUILDING) c) In cement mortar 1:5

Providing and fixing M.S. Tube hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer complete as specified and directed by department.

Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor.

Supplying, fitting and fixing in position reinforcement bars conforming to relevent IS code , for reinforced cement concrete works in piles including straightening, cleaning, cutting and bending to proper shapes and length as per specifications and drawings. The rings should be welded with vertical reinforcements as per specified IS codes of pract ice. (Inclusive of lap length, hook, chair, bend, anchor...etc)(A) TMT bar made of Primary producer (From Primary producer)

Supplying fitting and fixing inposition R/F bars conforming to I.S. code for RCC work including straighting, cleaning, cutting, and bending to proper shape and length as per details, supplying and binding with 20 G black annealed chairs, spacers etc. complete (upto 1st floor level) 1. Upto 1st floor level (b) ISI approved super ductile TMT bar (i) TATA/SAIL

Supplying, fitting and fixing door frame made of M.S. equal angle of size 40mmx40mmx5mm fabricated, welded, mitred and joined as per relevant I.S. Codes including fitting 8 nos. of M.S. hold fast, providing closing/ holding device for 2 nos. tower bolts of door for each side and 1 no. for fitting and fixing Aldrop (for single leaf) to the frame for fixing the door to the frame, applying primer to all steel surfaces fixing the frame to the wall/ R.C.C. members by embedding the hold fast secur ely in C.C. block of M-15 grade complete at all levels as specified and directed. (Door hinges to be paid as per relevant item of the schedule of rates).

Providing, fitting and fixing steel windows/ ventilators (openable) of standard rolled steel sections as per relevant I.S. Code-1038 joints mitred and welded with 15mmx3mmx100mm lugs embedded in cement concrete block of M-10 grade including providing and fixing of projecting hinges (not more than 65mm and not less than 15mm wide) bolting device and steel handles, peg stays of 300mm long etc. complete as per drawing including applying a priming coat of red-lead paint.

WHITE WASHING (a) White washing with lime on wall surfaces (two coats) to give an even shade including throughly brooming the surface to remove all dirt, dust,mortar drops and other foreign matter.

WHITE WASHING (c) Extra over item no. (a) above for every subsequent coat of white washing with lime on wall surfaces.

Providing and fixing flush door shutters solid core construc t ion with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S. code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with necessary wood screws. b) Non decorative type and block board core. (iii) 30 mm thick .

Supplying, fitting, fixing electrocoloured iron fittings of approved make, resonably smooth, free from sharp edges and comers, flaws and other defects and with counter sunk holes for wood screws including necessary screws etc. complete. a) Sliding door bolts ii) 250mm x 16mm

b)Tower bolts ii)250mm x 10mm

c) MS Door handle iii) 150 mm

Applying primary coat over new steel and other metal surface over 100m in width or girth after preparing the surface by throughly cleaning oil,grease, dirt and other foreign matter and scoured with wire brushes, fine steels, wood scrapers and sand paper. a) With ready mixed "red-lead/ red oxide" primer.

Painting two coats (excluding priming coat) on new steel and other metal surface with enamel paint of approved brand and manufacture(Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac) to give an even shade including cleaning the surface of all dirt, dust and other foreign matter. (i) Surfaces over 100mm in width or girth. a) General purpose (Asian paint/ Berger paint/ ICI paint/ J & N paint/ Nerolac).

25 mm thick cement concrete topping 1:2:4 ( 1 cement: 2 coarse sand : 4 coarse aggregate of 12 mm nominal size) finished with a floating coat of neat cement finish (base concrete to be measured and paid separately) to be laid in panels including curing complete as directed. A) At Toilet Floor

Providing antiskid tiles of approved quality size, shape not less then 8mm on floor, skirting over a cement morter bed 15mm thick 1:3 (1 cement : coarse sane! ) approved make fix wit h Fix-A-Tile (Choksey/Sika/Pedelite/Rouf)/White cement complete at all level as specified and direct ed. a) Normal range (sizes 300mmx300mm and above)

Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 ( cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A- Tile (Choksey / Sika / Pedelite / Rouf) /white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls). a) Normal range (Sizes 200 mm x 200mm and above)

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. (c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.

Providing Deep tube well!, Total depth required

Providing fitting and fixing vitreous water closet squatting pan (Indian type W.C Orissa pattern) WIth all fittings and fixtures complete including cutting and making good to the walls and floors whereever required. (Flushing Cistern to be paid separately) a) White i) Parryware make

Providing vitreous China wash basin with Cl/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately) Basin (without pedestal) (A) Parryware Make i) Parryware make a) White (i) Star Basin 550 x 400 (Cat. No. C0450)

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISi approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.l as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia.

(ii) 110mm dia.

(iii) 90 mm dia

(iv) 75mm dia.

Supplying, fitting and fixing 87.S degree PVC bend of (Supreme/Prince) or other ISi approved including joining ,fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. {i) 160mm

(ii) 110mm dia.

(iii) 90 mm dia

Supplying fiting and fixing 87.5 degree PVC bend with door of {Suoreme/Prince) or other ISi approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm

(ii) 110mm dia.

(iii) 90 mm dia

Supplying fiting and fixing PVC Plain single tee of (Supreme/ Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm

(ii) 110mm dia.

(iii) 90 mm dia

Supplying fiting and fixing PVC coupler of (Supreme I Prince)or other ISi approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (ii) 110mm dia.

(iii) 90 mm dia

Supplying fiting and fixing PVC reducer of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. as necessary complete at all levels including below G.L. as directed and specified. a) In exposed surfaces or in trenches. (iv) 110 mm x 75mm

(vi) 90 mm x 75 mm

Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approved including joining , fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L. as directed and specified. (a) 110 mm

Providing fitting and fixing PVC cowel of ISI make complete as directed and specified. (iv) 75mm dia. PVC cowel of ISI make

(ii) 110mm dia. PVC cowel of ISi make

Providing fiting & fixing C.I. Grating to the floors complete as directed and specified. (a) 110mm dia

(b) 75mm dia

Construction of filter bed in soak pit including earth work in excavation of soil and then filling up of the trench with brick bats/Charcoal covered with earth over a layer of A.C. plain sheet above brick bat filling complete as directed. (sizes of soak pit may vary depending on the sizes and capacities of the septic tank as well as the number of users as mentioned in the table.

Construction of inspection pit inside measurement 450mm x450mm x450mm flush with 100mm diameter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 finished with 13mm cement plaster in proportion 1:2 in side wall and floor. 450mm x450mm air tight C.I. inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed.

Supplying fitting and fixing approved uPVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L. as directed and specified. (B) Concealed by chieselling or breaking brick wall/ C.C. wall/ R.C.C. wall and making good to the damaged structure. SUPREME/ PRINCE / SFMC / FUSION BRAND or other equvalent approved brand (High presure pipe Sch-40) a) 50 mm dia

b) 40 mm dia

e) 20 mm dia

Item Supplying fitting and fixing C.P. bib cock 15mm dia of approved brand directed and specified. (G.I. & C.P pipes will be measured separately) (II) Jaquare make (i)Standard

(iii) 2-Way bib cock

Supplying fitting andfixing stop-cock of approved brand of size as mentioned below and directed and specified (G.I. & C.P. pipes will be measured and paid separately) I) Brass stop cock (heavy) of Sant make (i) 15 mm dia

Labour for boring hole for inserting tube well pipes through different soil/ rock media including hire charges of drill pipes, scaffolding, tools and plants as necessary and taking out the same and lowering pipes, fittings complete as directed by the Department. (ii) Bore hole of 100mm diameter

Supplying, fitting andfixing pipes plain/bevel ended for casing, conforming to relevant IS codes of practice including supplying and fitting of tube well accessories, lowering of assembly pipes concentrically in the borehole followed by supplying and packing of pea gravel free from dirt, dust and other foreign materials in the annular space between the borehole and assembly pipes complete as directed by the Department. II) PVC PIPE SUPREME /PRINCE/ FUSION /SFMC Brand v) 110mm diameter

vii) 160mm diameter

Supplying fitting and fixing GI filter 2.00metre long

Supplying, fitting and fixing suction pipes plain/bevel ended, conforming to relevant IS codes of practice including supplying and fitting of accessories, lowering of assembly pipes concentrically in the casing pipes complete as directed. B) PVC PIPE vii) 90mm diameter

Supplying fitting and fixing check valve {non return valve) including thread to pipes. f) 80 mm dia

Development of the tube well with compressor or by over pumping unit for 48 hours till sand free discharge is obtained

Flushing, clearing, washing and watering of the tube well

Supplying and placing plastic cylindrical vertical claused top (PCVC) tank of Sintex / Polycon /Patton make over the stagging with manhole cover with locking and cleaning arrangement including providing pads of size as required for inlet and outlet pipes (I) 2000 litre capacity a) Sintex make

Supplying and placing ferrocement septic tanks of rectangular shape in to pit with manhole cover with cleaning arrangement over single brick flat soling and 75mm 1:3:6 P.C.C. Baffle wall, inlet and outlet etc are provided at suitable points complete as directed.

Supplying fitting and fixing overhead adjustable Chrome Plated (C.P.) spray shower 15mm dia. Of Sona make with wall flange as directed and specified.(pipes will be measured and paid separately) (a) Supreme shower with arm

Wiring to a Light/Fan/Call Bell point with 2X 1.5 sq.mm. PVC Insulated single core unsheathed industrial (Multistrand) cable F.R. conforming to IS- 694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade upto 1100 Volts (Finolex/ RR Kabel or equivalent make as approved by the Deptt) in surface/recessed conduit wiring system with 20 mm dia 2 mm thick/heavy rigid IS : 9537 Part Ill conduit ( Berlia/AKG/Precision/ Presto Plast/ Polycab/MW or equivalent make as approved by the Deptt.) including 6 Amps flush Type Switch/bell push ( Anchor Penta/ Gold Medal/ Kolor kany.kom /Havels or equivalent make as approved by the Deptt.) GI/MS switch board (ISi marked) with Phenolic laminated sheet cover ceiling rose ( Anchor pento / Gold medel /Kolor kany.kom / Havels or equivalent make as approved by the Deptt. etc.complete. medium point upto 6mtr length

long point upto 10mtr length

Wiring to a 5 pin 6 A plug point with 1.5 sq.mm. PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS 694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100V (Finolex/ RR Kabel or equivalent make as approved by the deptt.) in surface/recessed 2 mm thick/heavy rigid ISI marked IS : 9537 PART Ill rigid PVC conduit (( Berlia/AKG /Precision/ Presto Plast/ Polycab/MW or equivalent make as approved by the Deptt.) wiring system including 5 pin 6 A flush type plug socket and 6 A F/T switch (Anchor penta/ Gold Medal/Kolar kany.kom/Havels or equivalent make as approved by the deptt.), GI/MS switch board (ISI marked with phenolic laminated sheet cover including earth continuity with 1.5 sq.mm. cable to third point of the plug socket etc. as required complete, when placed elsewhere. Medium point up to 6 Mtr. Length

Wiring for 5/6 pin 16 A plug with 4 sq.mm. PVC insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS 694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100V (Finolex/ RR Kabel or equivalent make as approved by the deptt.)in surface/ recessed conduit wiring system including 5/6 pin 16 A socket outlet (Anchor penta/ Gold Medal/Kolor kany.kom/Havels or equivalent make as approved by the deptt.) and 16 A flush type switch (Anchor penta/Gold Medal/Kolor kany.kom/ Havels or equivalent make as approved by the deptt.) GI/MS switch board (ISi mark with Phenolic laminated sheet cover eart h continuity with 2.5 sq. mm. cable to th e third pin of the socket as required complete with 20 mm dia 2 mm thick heavy rigid ISi marked IS : 9537 Part Ill rigid PVC conduit (Berelia/AKG/ Precission/ Presto Plast /Polycab/MW or equivalent make as approved by the Deptt.) Extra long point up to 15 met er length

Wiring for circuit wiring with PVC insulated Single core unsheated industrial (Multistrand) cable FR conforming to IS 694:1990 with flexible bright annealed electrolytic copper conductor for voltage up to 1100 V (Rnolex/RR kabel or equivalent make as approved by the deptt) in surface/recessed PVC conduit (Berlia/AKG/precission/Presto Plast/Polycab/MW or equivalent make as approved by the deptt) wiring system with 3 X 1.5 sq.mm. P.V.C. insulated cable in 20 mm. dia rigid conduit

Wiring for drawing Sub-Main Line with PVC Insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS 694:1990 with flexible bright annealed electrolytic copper conductor for voltage up to 1100 V (Finolex/RR kabel or equivalent make as approved by the deptt) in surface/ recessed PVC 20 mm dia 2 mm thick heavy ISi marked IS 9537 Part Ill rigid PVC conduit (Berlia/AKG/precission/Presto Plast/Polycab /MW or equivalent make as approved by the deptt) wiring system. With 4 X 4 sq.mm. + earth continuity with 2X2.5 sq.mm.cable in 25 mm dia 2 mm thick/heavy rigid PVC IS : 9593 part Ill conduit.

With 4 X 6 sq. mm+ earth continuity with 2 X 4 sq. mm cable in 32mm. Dia. 2mm thick/ heavy rigid PVC IS: 9537 Part-Ill conduit

Supplying including fitting and fixing of following Metal boxes for MODEL RANGE LEGRAND(ARTEOR), ANCHOR{AVE), MK(BLENZE), SCHNEIDER(ZENSELO), CRABTREE(MURANO) in surface/recessed system complete as per direction of department 1-2 module type metal

8 module type metal

Supplying including fitting and fixing of following MODEL RANGE LEGRAND(ARTEOR), ANCHOR(AVE), M K(BLENEZ), SCHNEIDER(ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department 2 module

Supplying including fitting and fixing of following MODEL RANGE LEGRAND(ARTEOR), ANCHOR(AVE), M K(BLENEZ), SCHNEIDER(ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department 8 module

Fitting and fixing of brackets on the wall in GI/MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover with all accessories such as GI/MS switch board (ISi marked) with phenolic laminated sheet cover including connection as approved by the Deptt. as required complete.

Supplying with fitting and fixing steel sheet, phosphatised, powder painted dust & vermin proof double door (IP-43) surface mounting vertical TPN MCB DB inco rporated with bas- bar 125A, neutral link, earth bar and din rail etc fitted on wall with grouting nuts and bolts as requ ired complete with making necessary connection as approved, specified and directed by the deptt. (Richa, Bentec, Adhunic/ equivalent make) 8 way TPN (8+24) double door

12 way TPN (8+36) double door

Supplying with fitting andfixing SPN 10 KA 240/415V 50 Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. B series( Schneider MG, legrand, Hager, Crabtree Xpro Make) 6 to 32 A

Supply, installation & testing of copper plate earth station with 600mmX600mmX6mm heavy duty copper earth plate with necessary 40mm dia. G.I. medium duty watering pipe with G.I fittings such as socket, tee, elbow, nipple and SOmmX40mm G.I. reducing socket for funnel including locking arrangement with 300mmX300mmX6mm C.I. hinged cover plat e complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of waif as specified and directed by the deptt.

Premium Model 1400 mm sweep (ORIENT /PSPO make)/Premium model 1400 mm sweep SS-390 Deco/havels make)

Supplying including fitting andfixing of following A.C. exhaust fan in the existing hole on the wall of following sweeps with making necessary connections as approved by the Deptt. As required complete and as directed by the department. Power Flow 225mm sweep (ORIENT) make

Supplying fitting fixing of ceiling fan regulator including connections etc complete as reauired

Supplying including fi tt ing and fixing of hot dip galvanised arm bracket for installation of luminaries. Header with top cap 300 mm long pipe of thickness 3 with arrangementto fix on pole top with 3 nos of bolts i) Armed of required length size 48.3mm out side dia x 3: 25 mm thick (BAJAJ/PHILIPS/VALMONT/PARUTHI ENGR/ NEZONE make) stiffener plate from arm of the following types Single armbracket 2000 mm for 3m to 10m poles

Supplying including installation, connection as approved by the Deptt., testing and commissioning of CENTRIFUGAL MONO BLOCK PUMP SET complete as directed and specified by the deptt. 7.5 HP three Phase Centrifugal monoblock pump set (Crompton Greaves/ Aquatic/ CRI/ V-Guard make) 2900 rpm A class insulation with Star delta Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T/ Siemens make) Fully Automatic citation.

Supplying, fitting & fixing Gate Post Light, as directed by the deptt.

Supplying, fitting & fixing Tube light with tube (hanging type, single tube), as directed by the deptt.

Supplying, fitting & fixing CFL lamp with fittings, as directed by the deptt.

SARBANANDA OJHA