Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L-1₹4.0 CrAccepted-AOC 424 1A OUTSIDE DATIA GATE NEAR RAGHURAJ SCHOOL PATHORIYA JHANSI U P | JHANSI | UTTAR PRADESH | 284001 | ₹4.0 Cr Quoted ₹4.2 Cr | L-1 | Accepted-AOC AOC |
| 2 | L-2₹4.3 CrRejected-Finance | ₹4.3 Cr | L-2 | Rejected-Finance L-2 |
| 3 | L-3₹4.5 CrRejected-Finance KARNATAKA | RAICHUR | KARNATAKA | 584123 | ₹4.5 Cr | L-3 | Rejected-Finance L-3 |
| Sl No | Description | Qty | Unit | RAJPOOT CONSTRUCTION COMPANY L1 | JC Company L2 | SATYAM CONSTRUCTIONS L3 |
|---|---|---|---|---|---|---|
| 1.00 | Clearing Jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50m outside the periphery of the area cleared. DSR 2.31 | 969 | Sqm | 2 ₹1,938 | 4.5 ₹4,360.50 | 4 ₹3,876 |
| 2.00 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50 m and lift up to 1.5m, as directed by Engineer-in-Charge. Hard rock (blasting prohibited) DSR 2.7.3 | 450 | Cum | 130 ₹58,500 | 810 ₹3.6 L | 850 ₹3.8 L |
| 3.00 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. DSR 2.35.3.1 | 548 | Sqm | 120 ₹65,760 | 180 ₹98,640 | 160 ₹87,680 |
| 4.00 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. DSR 2.27 | 321.75 | Cum | 1,000 ₹3.2 L | 1,170 ₹3.8 L | 1,250 ₹4.0 L |
| 5.00 | PCC 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). DSR 4.1.8 | 171.76 | Cum | 3,500 ₹6.0 L | 3,960 ₹6.8 L | 3,900 ₹6.7 L |
| 6.00 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.
All works upto plinth level : Concrete of M-25 grade with minimum cement content of 330 kg /cum DSR 5.33.1.1 | 345.68 | Cum | 5,800 ₹20.0 L | 5,400 ₹18.7 L | 6,000 ₹20.7 L |
| 7.00 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.
All works above plinth level upto floor V level : Concrete of M-25 grade with minimum cement content of 330 kg /cum. DSR 5.33.2.1 | 361.9 | Cum | 5,800 ₹21.0 L | 5,850 ₹21.2 L | 6,400 ₹23.2 L |
| 8.00 | Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 6.2.1 | 488.92 | Cum | 5,000 ₹24.4 L | 3,600 ₹17.6 L | 4,350 ₹21.3 L |
| 9.00 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources). DSR 4.10 | 600 | sqm | 100 ₹60,000 | 180 ₹1.1 L | 225 ₹1.4 L |
| 10.00 | Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 6.34.1 | 540.46 | Cum | 5,500 ₹29.7 L | 5,400 ₹29.2 L | 6,000 ₹32.4 L |
Tender Value
₹5.0 Cr
EMD Value
₹10.0 L
Closing Date
6 Oct 2025, 12:00 pmClosed
SE PMGSY Circle Kanpur
SE office PMGSY Circle Kanpur
Construction work of office building of Uttar Pradesh Vigilance Establishment Jhansi Center
2025_WBEAP_1076283_1
1498/167C-PMGSYC/2025-26 DT. 05.08.2025
Open Tender
Civil Works - Buildings
365 days
Jhansi
Please refer Tender documents.
3 documents required · 3 mandatory
₹7,970
Yes
₹10.0 L
Yes
SE office PMGSY Circle Kanpur
21 Jan 2026
22 Sept 2025
6 Oct 2025
22 Sept 2025
6 Oct 2025
22 Sept 2025
26 Sept 2025
Amount
Clearing Jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50m outside the periphery of the area cleared. DSR 2.31
Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30 cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50 m and lift up to 1.5m, as directed by Engineer-in-Charge. Hard rock (blasting prohibited) DSR 2.7.3
Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor : With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. DSR 2.35.3.1
Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. DSR 2.27
PCC 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). DSR 4.1.8
Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level : Concrete of M-25 grade with minimum cement content of 330 kg /cum DSR 5.33.1.1
Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level : Concrete of M-25 grade with minimum cement content of 330 kg /cum. DSR 5.33.2.1
Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 6.2.1
Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources). DSR 4.10
Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 6.34.1
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Mild steel and Medium Tensile steel bars DSR 5.22.1
Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. DSR 10.31
Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works. DSR 10.25.2
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. DSR 9.20.1
Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R3 series with frame (98mm & above) x (40mm & above) & both glazed and fly screen sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system, (Height upto 1.8m). DSR 9.147.A4.2
Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces. DSR 10.5.1
12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) DSR 13.1.1
15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand) DSR 13.2.1
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 1000x1000 mm DSR 11.41.4
Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick. DSR 11.26.1
Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete. DSR 11.38
Supply and stacking of Fly ash conforming to IRC- 58 at site, including carriage, loading , unloading & stacking up to any lead (measured stacks will be reduced by 20% for payment). DSR 2.37
Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 35 mm thick shutters. With ISI marked stainless steel butt hinges of required size - Second class teak wood. DSR 9.27.1.2.1
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. DSR 13.80
Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm. over and including one coat of Special primer applied @ 0.75 ltr / 10sqm . DSR 13.48.1
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). DSR 10.28
Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests DSR 17.1.1
Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid DSR 17.3.1
Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern. DSR 17.5.1
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps DSR 17.7.1
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm. DSR 17.10.1.1
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. DSR 17.31
Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. Providing and fixing toilet paper holder : C.P. Brass DSR 17.33
Providing and fixing soil, waste and vent pipes : 100 mm dia. Sand cast iron S&S pipe as per IS: 1729. DSR 17.35.1.1
Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and includingcement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 100 mm dia. Pipe DSR 17.37.1
Providing and fixing heel rest sanitary bend 100 mm dia Sand cast iron S&S as per IS - 1729 DSR 17.40.1.1
Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete : 100x100x100x100 mm Sand cast iron S&S as per IS - 1729 DSR 17.41.1.1
Providing and fixing sand cast iron S&S off sets as per IS: 1729 76 mm off sets With 75 mm dia pipe DSR 17.53.1.1
Providing and fixing terminal guard: 100 mm Sand cast iron S&S as per IS - 1729 DSR 17.56.1.1
Providing and fixing collar: 100mm dia Sand cast iron S&S as per IS - 1729 DSR 17.57.1.1.
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. DSR 17.71
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work (20 mm nominal outer dia). Pipes. DSR 18.9.2
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work (25 mm nominal outer dia). Pipes. DSR 18.9.3
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge : External work (32 mm nominal outer dia). Pipes. DSR 18.9.4
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore DSR 18.17.1
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore DSR 18.17.1A
Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore DSR 18.18.2
Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore DSR 18.18.3
Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 20 mm nominal bore DSR 18.20.2
Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 25 mm nominal bore DSR 18.20.3
Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) : 100 mm diameter Class I DSR 18.31.1.1
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.l. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design: With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 DSR 18.33.1
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: 15 mm nominal bore. DSR 18.49.1
Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore. DSR 18.50.1
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore DSR 18.51.1
Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore. DSR 18.52.1
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 : 15mm nominal bore DSR 18.53.1
Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. DSR 18.53A
Providing and fixing 25 mm thick shutters for cup board etc. : Panelled or panelled & glazed shutters : Superior class teak wood including nickel plated bright finished M.S. piano hinges with necessary screws. DSR 14.26.1.1
Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30 DSR 16.78.1
Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in charge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). DSR 16.75
Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers. DSR 5.9.5
Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20x20 mm square bar D.S.R. 19.15.1
Providing and fixing in position precast R.C.C. manhole cover and frame of required shape and approved quality MD-10-circular shape 560 dia internal dia meters DSR-19.19.3.1
Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. With average thickness of 120 mm and minimum thickness at khurra as 65 mm. DSR 22.7.1
Earth work by mechinical / manual means in rough excavation, banking excavated earth in layers not exceeding 20cm in depth, breaking clods, watering, rolling each layer with 'A tonne roller or wooden or steel rammers, and rolling every 3rd and top-most layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide banks or filling up ground depressions, lead upto 50 m and for all lift .All kinds of soil . DSR 2.2.1
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. DSR 18.48
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. Rocky strata including Boulders. 300 mm dia. DSR 23.1.2.1
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings& accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia. DSR 23.3.1
Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. DSR 23.5
Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. DSR 23.6
Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge. DSR 23.9
Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. DSR 23.12
Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for bore well of: 100 mm dia. DSR 23.13.1
Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 100 mm clamp. DSR 23.14.1
Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 100 mm dia. DSR 23.15.1
Providing and fixing 1 mm thick M.S. sheet sliding-shutters, with frame and diagonal braces of 40x40x6 mm angle iron, 3 mm M.S. gusset plates at the junctions and corners, 25 mm dia pulley, 40x40x6 mm angle and T- iron guide at the top and bottom respectively, including applying a priming coat of approved steel primer. DSR 10.4
Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. DSR 12.52.3
Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent . DSR 11.56.1
Supply, Installation, Testing amd Commissioning of LT Panel vermin proof floor mounting , M.S. channel base with bottom and Fabricated out of 2.0/1.6mm thick CRCA sheet steel, painted with powder coated paint of shade as per the direction of Engineer In-Charge after proper sheet treatment process of sheet steel. The Bus Bar of panel shall be of Electrical grade High Conductive Aluminum alloy of appropriate cross section as per rating.The main bus bar shall run throughout the panel of rating as main incomer rating. The Bus Bar shall be supported by non hygroscopic SMC/DMC Bus Bar supports which shall be mounted on proper interval to ensure the bear the jerks of short Circuit of 50kA for panels having ACB as Incomer & 36kA for panels having MCCB Incomers. Panel shall be constructed in fully Segregated Compartment Design for Each Feeder as per 3b construction Format. The Panel shall be completed in all respect as per IS: 8623 Part-2&3. There shall be Separate Metering Compartment for incomer metering and outgoing metering.All Incomer Feeders shall be provided with Multifunction Metering along with Phase Indicating Lights and other associated components such as CT, control MCB Terminal Block etc. and all Outgoing Feeders 100A & above shall be provided with 3 phase Ammeter along with phase Indicating Lights and other associated components such as CT, control MCB Terminal Block etc. The Feeders above shall be provided ac accommodated all Measuring Instruments shall be Digital type & all Indicating Lights shall be LED type. Wiring shall be done from 1100V Grade PVC Insulated copper flexible wire. All ACB shall be Electrically operated Draw-out type with Microprocessor Based O/L, S/C & E/F Release of Breaking/ Withstand Capacity (ICU/ICs/Icw) 50kA or more All MCCB shall be Thermal Magneetic/Microprocessor with O/L & S/C Protection along with Required Spreaders & Extended Rotary Handle with pad Locking facility of Breaking capacity (ICU/ICS) 36kA or more All MCB shall be Thermal 10kA 'C' Curve. Cubicle type switch board shall be Cat-A and B only. I/C- 800A / 415V MCCB - 1No. O/C- 100A MCCB 1 No., 250A MCCB-1No., 63A MCCB-7 No., 32A MCCB-1No.
Supply, Installation, Testing amd Commissioning of LT Panel vermin proof floor mounting , M.S. channel base with bottom and Fabricated out of 2.0/1.6mm thick CRCA sheet steel, painted with powder coated paint of shade as per the direction of Engineer In-Charge after proper sheet treatment process of sheet steel. The Bus Bar of panel shall be of Electrical grade High Conductive Aluminum alloy of appropriate cross section as per rating.The main bus bar shall run throughout the panel of rating as main incomer rating. The Bus Bar shall be supported by non hygroscopic SMC/DMC Bus Bar supports which shall be mounted on proper interval to ensure the bear the jerks of short Circuit of 50kA for panels having ACB as Incomer & 36kA for panels having MCCB Incomers. Panel shall be constructed in fully Segregated Compartment Design for Each Feeder as per 3b construction Format. The Panel shall be completed in all respect as per IS: 8623 Part-2&3. There shall be Separate Metering Compartment for incomer metering and outgoing metering.All Incomer Feeders shall be provided with Multifunction Metering along with Phase Indicating Lights and other associated components such as CT, control MCB Terminal Block etc. and all Outgoing Feeders 100A & above shall be provided with 3 phase Ammeter along with phase Indicating Lights and other associated components such as CT, control MCB Terminal Block etc. The Feeders above shall be provided ac accommodated all Measuring Instruments shall be Digital type & all Indicating Lights shall be LED type. Wiring shall be done from 1100V Grade PVC Insulated copper flexible wire. All ACB shall be Electrically operated Draw-out type with Microprocessor Based O/L, S/C & E/F Release of Breaking/ Withstand Capacity (ICU/ICs/Icw) 50kA or more All MCCB shall be Thermal Magneetic/Microprocessor with O/L & S/C Protection along with Required Spreaders & Extended Rotary Handle with pad Locking facility of Breaking capacity (ICU/ICS) 36kA or more All MCB shall be Thermal 10kA 'C' Curve. Cubicle type switch board shall be Cat-A and B only. I/C- 100A / 415V MCCB - 1No. O/C- 32A MCCB - 3Nos.
Wiring for Light Point, Street Light point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate,suitable GI box and earthing the point with 1.5sq.mm FRLS PVC copper conductor single core cable etc. as required.
Wiring for Fan, Fresh air fan point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate,suitable GI box and earthing the point with 1.5sq.mm FRLS PVC copper conductor single core cable etc. as required.
Wiring for Call bell point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate,suitable GI box and earthing the point with 1.5sq.mm FRLS PVC copper conductor single core cable etc. as required.
Wiring for Exhaust point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate,suitable GI box and earthing the point with 1.5sq.mm FRLS PVC copper conductor single core cable etc. as required.
Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings) (For Plug Point and Aquaguard)((2 No. for TV)
Supply and Fixing of suitable size GI box with modular plate and cover in front of surface or in recess, including providing and fixing 2 nos. 3 pin 5/6A modular socket outlet and 2 nos. 5/6A modular switch, connections etc. as required. (For light Plugs to be used in non residential buildings).
Supply and Fixing of brass Angle holder including connection etc. as required.
Supplying and drawing 1 x 1.5 sq. mm size of FR PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. (For Inverter Wiring)
Supply and Fixing of suitable size GI box with modular plate and cover in front of surface or in recess, including providing and fixing 25 A modular socket outlet with 25 A modular SP MCB C curve including connections painting etc. as required. (AC & Geyser)
Supply and Fixing of suitable size GI box with modular plate and cover in front of surface or in recess, including providing and fixing 6 pin 15/16 A modular socket outlet and 15/16 A modular switch connections etc. as required.
Supplying and fixing 4 way (4+12), horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
Supplying and fixing of 12 way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
Supply and fixing of 5 to 32 amp rating 240/415V, 10KA, C curve DP MCB suitable for inductive load of following poles in existing DB complete with connections, testing and commissioning etc. as required.
Supply and fixing of 5 to 32 amp rating 240/415V, 10KA, C curve SPMCB suitable for inductive load of following poles in existing DB complete with connections, testing and commissioning etc. as required.
Supply and Fixing of 63 Amp. 4 Pole MCB(10KA) C curve. Make-Havells or equivalent
Supply and Fixing of 32 Amp. 4 Pole MCB(10KA) C curve. Make-Havells or equivalent
Supplying and fixing 25A rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.
Supply and fixing of LED Tube Light with heavy duty Metal Box type Tube Light fitting 1x22 watt suitable for upto 1x 22 watt LED Polycarbonate tube light complete Including tube suitable for both surface & suspended complete in all respect 2620 system lumens, >120 Lm/W, PF>0.95, THD<10%, CRI >80, sheet thickness min 0.8mm, Tube with aluminium heat sink, >300V over voltage protection, 2.5 KV internal Surge Protection, with 5year warrantee CAT AAA
Supply and Fixing of 9 watt LED DECORATIVE WALL light Complete in all Respect.Make Havells or Equivalent 360-720 systems lumens, 120lm/W, PF › 0.95, THD <10% , CRI>80,with 5 years warrantee Make-Havells or equivalent.
Supply and fixing of IP 20, Front Lit, Mid Power SMD type LED Light, recess/Surface mounting round 18 Watt to 20 Watt, Cut out Min 150 mm, Height Min 40 mm,, LED Down Lighter having Powder coated die cast aluminium housing with heat sink, High purity / transmisivity UV Stabilized Non yellowish diffuser/ Reflector for uniform light distribution, detachable driver set, suitable for 24 Hr Continuous Operation, Complete in All respect. 2160-2400 system lumens, >120 Lm/W, PF>0.95, THD <10% at full load, CRI >80, , >300V over voltage protection, 2.5 KV internal Surge Protection, with 5 years warrantee CAT AAA
Supply and Fixing of 20 watt LED Mirror Light Complete in all Respect.Make Havells or Equivalent 2160-2400 systems lumens, >120lm/W, PF › 0.95, THD <10% , CRI>80,with 5 years warrantee Make-Havells or equivalent.
Supply and fixing of LED Street light Fitting with mandatory driver set having die cast aluminium body with toughend glass/ UV stabilized PC Cover and lenses suitable for 60Watt. to 72 Watt. Confirming to IP 66, and IK07 and above protection having Company LOGO Engraved complete in all respect including Labour. 7200-8640 system lumens, High Power LED with lenses, >120 Lm/W, PF>0.95,, Potted driver Set in Metal housing (Not Circuitory), Phase to phase Protection at 440V & >300V auto cut and re-start feature, 4 KV internal Surge Protection, with 5 years warrantee CAT AAA
Submain wiring along with earth wire with the 2 x 1.5 sqmm +1x 1.5 sqmm earth wire (for Plug,Computer, Aquaduard,TV point) of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required.
Submain wiring along with earth wire with the 2*2.5 sqmm +1* 2.5 sqmm earth wire(Looping Power) of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required.
Submain wiring along with earth wire with the 2 x 4 sqmm +1 x 4 sqmm earth wire (Power Plug) of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required.
Submain wiring along with earth wire with the 2 x 6 sqmm +1 x 6 sqmm earth wire(AC) of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required.
Submain wiring along with earth wire with the 2 x 10 sqmm +1 x 6 sqmm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required.
Submain wiring along with earth wire with the 4 x 10 sqmm + 2 x 6 sqmm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required.
Submain wiring along with earth wire with the 4 x 16 sqmm + 2 x 6 sqmm earth wire sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required.
Submain wiring along with 4×25 Sqmm + 2×6 Sqmm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required.
Supply and Laying of 70 Sq mm 3-1/2 Core Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade at a depth of 750mm below ground level over a cushion of 75mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc of suitable size or as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.
Supply and Laying of 240 Sq mm 3-1/2 Core Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade at a depth of 750mm below ground level over a cushion of 75mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc of suitable size or as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.
Supply and Laying of 400 Sq mm 3-1/2 Core Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade at a depth of 750mm below ground level over a cushion of 75mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc of suitable size or as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.
Supply and making end termination with brass compression gland and aluminium lugs for 3.5 x 70 sqmm (38mm) size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1kv grade as required.
Supply and making end termination with brass compression gland and aluminium lugs for 3.5 x 240 sqmm size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1kv grade as required.
Supply and making end termination with brass compression gland and aluminium lugs for 3.5 x 400 sqmm (82mm) size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1kv grade as required.
Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.
Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.
SITC of 1200 mm sweep, BEE 5 star rated, ceiling fan with brush less DC motor, class of insulation-B, 3 nos blades, 30cm long down rod, 2 nos canopies, shackle kit, safety rope, copper winding, pf not less than 0.9, service value (CM/M/W) minimum 6.00 air delivery minimum 210cum/min, 350rpm(tolerance as per IS: 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts,washers, temperature rise=75degree C max, insulation resistance more than 2 mega ohm, suitable for 230V, 50Hz, single phase AC supply, earthing etc. complete as required.
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.
Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.
Supply and Fixing of L.E.D. Bulbs, 9 W app. Make Havells or Equivalent
Supply and Fixing of Heavy Duty Exhaust Fan 300 mm size sweep 900 RPM single phase including cartage and fixing Complete in all respects.Make Havells or equivalent
Supply and Fixing of Fresh air Fan 200mm Sweep single phase including cartage and fixing Complete in all respects.Make Havells or equivalent
Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work.
Supply, Installation, Testing and Commisioning of 40 KVA 3 Phase 415V, 50Hz liquid cooled silent DG Set based on CPCB - 4 guidelines comprising of diesel engine of reputed make. Fitted on a common base frame along with other accessories i.e.Auto start,stop panel, battery charger, first fill of lube oil, 4 nos. chemical electrode earthing, 40 meter 35 sq.mm 3.5 core cable of reputed make as per PWD specifications, Automatic changover etc. complete in all respect. including cost of freight charge from ex. works to site place, etc. Two Year warranty. Compelete in all respect. Voltage-415 ± 2% volt Rated output minimum-55HP Governing class-G2 No. of cylinder-4 Speed 1500 rpm Insulation class-H
Supply, Installation, Testing and Commisioning of Grid connected Solar Power Plant having capacity of 45 KWp for optimizing energy savings. It includes PV modules ranging from 580-620W, Grid-Tied inverter, Galvanized mounting structure, ACDB?DCDB as required, Earthing and Lightning Protection, consumer friendly Montitoring System complete in all respect
Supply, Installation, Testing and Commisioning of 10 Passenger elevator with 3 stops complete in all respect with one year Warrenty. Load or Capacity- 680Kg or 10 Persons Stops and Openings- 3 stops and 3 openings, single entrance car Well Dimension-1800mm*1800mm Car Dimension- 1200mm wide X 1400mm deep X 2200mm hieght Door Dimensions-800mm wide X 2000mm height Door type- Central Opening Car door finish- SS hairline AISI441 Car flooring- Granite Additional Features:- Emergency Alarm, Overload Function, Constant indication/Buzzer, Auto rescue Device activation, Manual rescue, Automatic brake test function, Phase reversal function, car emergency Light, Fireman drive, Automatic close door, car door lock, Emergency Rescue device with audio announcer, Fire rated for landing door as per IS.
IP- based CCTV system for building security, comprising PTZ/Fixed camera cabling, recording, display system, hardware and software. S/O 2MP lP Bullet/Dome IR Camera Maximum Resolution 2 MP, Auto Day/Night switch, 3 D DNR,WDR,HLC, BLC etc., ROI Coding Support smart Suppliment light IP 67, Support dual streem, DC 12 V/PoE Power supply Support remote mounitering by smarts Phones & Tablet PCs with iOS & Andoraid OS, Support lying crossing dedection reson intrusion dedection. support SMD. Make - Godrej/Hikvision or Equivalent
S/O 32ch NVR STI-NVR32S2-4K(2 Satta) Supports 32 CH 8 MP/6 MP/ 5MP/ 4MP/3MP/1080 P/1280 x 1024 / 960 P / 720 P / 960 H/ D1 / CIF IP input. Playback - 16 CH Simultaneous Playback, Such-Timeslice,Time,Event,Tag,Smart & target Database search, Supports face dedection & compression, Support multiple Video Content Analetics Event, Such as object abanboned/missing,reson intrusion, tripwire, Video exception etc. support POS information over layon live view & Playback, express & flexible backup via USB, network & show on, Penta Plex-Preview,record,Playback,backup & remotee excess. Remote control via Web client or CMS Preview,record,Playback,backup, PTZ & Confrigration, dual streen technology for local storage with high defination, remote network transmation & remote survillance with mobile device, 4K HD Output, True high resolution display, Support PTZ preset & Auto Cruise, upto 255 presets & 8 Cruise support NAT fuction & QR Code scaning by mobile phone, Powerfull mobile survillance by smart phones with IOS & Andoid OS.. Make - Godrej/Hikvision or Equivalent
PTZ Camera (4MP) Lens Type- PTZ, Focal Length 4.8-120mm, Make - Godrej/Hikvision or Equivalent
HDD 10TB(Surveillance) WD/Seagate (15 days backup)
Supply and Laying Optical fire cable 6 core. Complete in all respect.
S/O 08 Port l0/100/1000 PoE Giga Switch Maximum PoE - 150 Watt, 8 x 1000 Mbps PoE Ports, 2 x 1000 Mbps up link ports and 2 x 1000 Mbps SFP Ports. Support IEEE 802.3 af/at support restrain network storm, All port supported by MDI / MDIX Autoflip & Self Neg, Blitin Power supply, Maximum power of single PoE port 30 Watt fan less, Netural cooling, Small, Compact & cuiet design, suitable for desktop or wall, Support Lighting protection 4000V. Make - Godrej/Hikvision or Equivalent
4U Rack with Extension Boards & Accesso ries. {Secu re net/D link)
Splicing
Display TV 43" Make:- Samsung ultra 4K or equivalent
Termination box
LC Cable
Supplying and Drawing of UTP 4 pair Cat 6 LAN cable in the existing Surface/recessed steel/PVC conduit as required.
RJ45 connector 100 Pcs Packet
Installation, Testing and commissioning of all CCTV Equipment charges
Supply, Installation, Testing and commissioning of electro-mechanical boom barrier with all accessories upto 6 mtr in length. Make:- ESSL or Equivalent (i) boom barrier
(ii) Sensor for working boom barrier.
(iii) Remote for operating boom barrier.
Supply, Installation, Testing and commissioning of Door frame metal detector 33 zone or above nominal size complete in all respect. External dimension(Approximately) - 930mm(width) X 760mm (Deep) X2220 (Height) Channel Dimension(Approximately) - 760mm(width) X 760mm (Deep) X2010 (Height) Make:- ESSL or Equivalent
Supply, Installation, Testing and commissioning of baggage scanner, small computer based multi energy X-ray baggage inspection system, mounted on castor wheels, capable of passing through bags of dimension 540mm (Width) X 350mm (Height), belt height 750mm to 850mm, 22 inch/24 inch LCD monitor, Input/Output rollers with frame Make:- ESSL or Equivalent
LC to LC cable mode cable duplex
6 count optical fiber cable single mode, with PLB HDPE duct pipe 32mm
Cisco switch 24 port + 4SFP L3 Gigabit with 2 SMD GLC 10G module
UPS 600VA With Batteries & Accessories Supported (APC/Luminous/Tata )
4U Rack with Extension Boards & Accesso ries. {Secu re net/D link)
Electrical fitting material like casing channel, 4 way gang box, socket switches etc complete.
Splicing
I/O box (Set of 3)
SM42U server rack with 4 fans, PDU,Tray patch panel and cable manager. Make- Dlink or equivalent)
LIU 8 port sliding
SITC of networking of OFC, cat6, laying,electrical and civil work included.
Crystal SN24 EPBX 2+16 Line
Supplying and Drawing 2 pair 0.5mm dia FRLS PVC insulated annealed copper conductor, unarmoured telephone cable in existing Surface/recessed steel/PVC conduit as required.
C11 Phone
M71 Phone
Crone box
SITC charges of telephone system.
Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.
Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED metallic cover complete with all connections etc as required.
Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.
Supplying, installation, testing & commissioning of addressable fire control module complete as required.
Supplying, installation, testing & commissioning of addressable manual call point complete as required.
Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.
Supplying, installation, testing & commissioning of fault isolator complete with base as required.
Supplying & laying of 2x1.5 sqmm fire alarm armoured cable,600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.
(A)Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation,conforming to IS-325. (D ) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (E) Suitable cement concrete foundation duly plastered and with anti vibration pads. 900 lpm at 35 m Head
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 80 mm dia
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 100 mm dia
Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80 mm dia
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm dia
Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required : 100 mm dia
Supplying, fixing, testing and commissioning of stainless steel Y-stainer fabricated out of 1.6 mm thick stainless steel Grade 304, sheet with 3mm dia holes with stainless stel flange. 100 mm dia
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636(type-A) as required : Stainless Steel (Grade 304)
Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required.20 mm nominal internal dia water hose thermoplastic(Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall.Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 40 m
Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)
Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :2 way-150 mm dia M.S. Pipe
Supplying and fixing air vessel made of 250 mm dia, 8mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.
Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.
Supply and laying of 16 Sqmm 4 core aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.
Supply and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1kv grade as required. 4 x 16 sqmm (22mm)
Provinding & fixing carbon steel Fire Man Axe with rubber insulated handle tested to 20000 volts.
Providing & fixing of pressure Gauge in M.S. pipe line including connection etc. as required.
Provinding & fixing of 1.6 mm thick M.S. Hose Box/ Frame Door capable of accommodating fire Landing Valve Hose Pipes fitting & accessories The door shall have a front glass with lock and key arrangement & shall be painted with post office red colour(approval shall be taken on the basis of submitted sample before ordering) cost of fire extinguisher not included in item rate.( Liasioing with civil contractor box(by civil contractor)
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
SITC of cast iron Ball Valve 25mm dia.
Supply and fixing of self illuminating glow exit signage Size 400x150 mm.
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 10000 Ltr. Capacity (5000x2) Ltr.
Supply and fixing of fire extinguisher Co2 type 4.5 kg capacity (ISI marked IS: 2878 & TAC approved) complete with intial charge and wall braket along with supply of all material and labour for proper completion of work.
Supply and fixing of fire extinguisher ABC type 6 kg capacity (ISI marked IS: 15683 & TAC approved) complete with intial charge and wall braket along with supply of all material and labour for proper completion of work.
SITC of Emergency Light 12V DC,230V AC, chargable complete as required.
Supply and fixing of LED Street light Fitting with mandatory driver set having die cast aluminium body with toughend glass/ UV stabilized PC Cover and lenses suitable for 75Watt. to 90 Watt. Confirming to IP 66, and IK07 and above protection having Company LOGO Engraved complete in all respect including Labour. 9000-10800 system lumens, High Power LED with lenses, 120 Lm/W, PF>0.95, THD <10% at full load, CRI >70,, Potted driver Set in Metal housing (Not Circuitory) Phase to phase Protection at 440V & >300V auto cut and re-start feature, 4 KV internal Surge Protection, with 5 years warrantee CAT AAA
Supply and Laying of 6 Sq mm 2 Core Aluminium Conductor PVC insulated armoured served sheathed cables 1100V grade at a depth of 750mm below ground level over a cushion of 75mm thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc of suitable size or as directed by Engineer in Charge complete in all respect including excavation and refilling. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.
Supply and fixing of 7 mtr. G.I. Octagonal pole of approved make (top dia 70 mm, Bottom dia 130 mm & Base plate 12 mm thick) having 3 mm, thickness with single arm bracket length of 1 mtr. length in 1:2:4 RCC foundation bolt including the cost of foundation, excavation & back filling and Required T & P complete in all respect.
Supply and fixing of 5 to 32 amp rating 240/415V, 10KA, C curve SPMCB suitable for inductive load of following poles in existing DB complete with connections, testing and commissioning etc. as required.
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.
Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.
JC Company (BID ID -5583666)
SATYAM CONSTRUCTIONS (BID ID -5584717)
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 1.71 MB
BOQ_1966004.xls
BOQ • 0.45 MB
Download all tender documents and submit your bid