Spl repair to JCO/OR Md Accn block No P-01 of Bana Singh Enclave and Provn of Dhobi Ghat near bldg No T-17 under AGE B/R-II at Tibri Mil Stn Gurdaspur.

Amount

M&L for cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in flooring complete all as specified.

M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) including bitumen primer @ 0.40 kg /Sqm laid on applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m by forced application with butane torch over entire roof area with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in after cleaning surface complete all as specified and directed and all as per manufacturer's instructions.

M&L for removal of existing treatment, all loose gravel cement mortar, dirt, oil, grease and foreign material by jet of dry air, roughening and cleaning the surface mechanically or by grinding to make it smooth surface before application loose existing bituminious material manually and with heat torch gun to get smooth plain finished surface with no loose material on surface . Repair all joints & cracks applying primer with smart care epoxy primer to seal the pores/cracks and enhance the adhesion of the coating. (a) Apply first coat of fibre reinforced elastomeric liquid water proofing membrane formulated with PU hybrid poymers and reinforcing acrylic fibres with sun reflective index (SRI) of 100-110, having minimum elongation of 300% to 350%, tensile strength of 1.8 Mpa to 2.9 Mpa and shall have cracks bridging ability upto 10-12 degree celcius with 33% dilution of priming coat. Laying of fiber mesh of 0.3mm thickness weave in leno pattern having 45 gsm/ sqm and pasting it properly with overlap of 50 mm and allow it to dry for 10 to 12hrs. Apply second coat of undiluted coat @ 0.45ltr/sqm and allow it to dry for 4 to 5 Hrs. Apply third and final coat undiluted @0.45 ltr/sqm all as specified and as per manufacturers instructions. (Note : Application of water proofing treatment shall be done by authorised applicator only) .

M&L for water proofing treatment to sunken floors of toilets, laboratories, bath, WCs, kitchen etc as under:- (i) Application of two component acrylic modified cementitious coating :- (a) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates shall be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance existing coating and achieve a gripping profile that is clean, dry and free from laitance and any other from of surface containmation. The installation instruction in manufacturer's published literature shall be strictly complied with, including but not limited to the following:- (b) Chipping out any visible cracks in "V-Groove" pattern as applicable. Cleaning of cracks & filling with SIKA latex SBR 100 putty/Dr. Fixit 302 SBR latex/ perma latex SBR/FOSROC Nitbond SBR latex/Asian paint latex as required. Final cleaning of surface with powder grinder, wire brush, hair brush & vacum pressure. (c) Providing protection concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) 50mm thick admixed with plastocrete over the applied water proofing coating on horizontal surfaces.(Admixture: Sikaplastocrete plus/FOSROC/Dr. Fixit/STP/CICO confirming to IS 2645.) (d) Dampen all surface immediately ahead of apllication of acrylic modified cementitious coating of SIKA top seal-107/Brush bomd FOSROC/Dr. Fixit/STP/CICO. (e) Whilst the surface is still damp from saturation (SSD) apply one coat of acrylic modified cementitious coating of SIKA top seal-107/ Brush bond FOSROC/Dr. Fixit/STP/ white first coat is wet.

(f) Apply glass fabric sheet of approved make while the first coat is wet. (g) Once touch dry, apply second coat of acrylic modified cementitious coating of viscosity as per manufacturer ins on the entire area. Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direction right angle to the previous coat. (h) The waterproofing coating shall be taken to a height minimum 300mm above the finished floor level on the vertical surface. (j) Curing acrylic modified cementitious coating immediately after application (min 6-8 hrs drying) for a min of 3 to 5 days to ensure full cement hydration and to minimize cracking. (k) A protection plaster (15mm thick) in ready mix mortar to be a apllied on the walls. (l) All the corners and joints shall be pretreated with an elastic waterproofing sealing tape with a woven bonding mesh on each surface and an elastic expansion zone in the centre of make seal tape SIKA/FOSROC/Dr. Fixit/STP. (m) The membrane has to be protected in accordance with the manufacturer's recommendation until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and carryout repairs in accordance with manufacturer's instructions. (n) Waterproofing treatment shall be carried out through authorised applicators.

(o) All the joints of pipes and traps within the sunken portion shall be sealed properly by epoxy sealant. (p) All CI/PVC Traps in sunken slabs to be enclosed with PCC 1:1.5:3 (using 20mm graded crushed stone aggregate) (min 15cm) all round. (q) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40 mm graded crushed stone aggregate) complete all as specified. (r) Providing drainage spout pipe GI 40mm dia light grade upto outside of outer wall (Approx 300 mm to 450 mmlong) incl cutting to existing wall and making good the distrubed surface complete all as specified and directed. (s) Providing 25mm thick cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in flooring for laying floor finishes all as specified. Note:- Items no. (q), (r) and (s) shall be measured and paid for seperately.

M&L for PCC 1:2:4 type B0 (using 12.5mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

Demolition of cement concrete in ground floor and paving n.exc 15cm above ground level.

M&L for 50mm thick PCC (1:2:4) type B-1 (20mm graded crushed stone aggregate) as in plinth protection all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar all as specified and directed.

M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.06 sqm but n.exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match the surface including 15 mm thick screed bed in cm 1:6 complete all as specified.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.18 sqm but not exc 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in cm 1:6 complete all as specified.

M&L for glazed ceramic dark shade coloured tiles of size 450x350x7mm thick joint free on and incl 10mm thick screed bed in cm(1:4)set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles vertical surfaces of wall as in skirting/ dado complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc.

M&L for marble work 16-18mm thick (table rubbed and polished) in steps, jambs, pillars window cills , cooking platforms , stair case and like in cement mortar (1:4) incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed and approved by Engr-in-charge.

Demolition of cement concrete (unreinforcement) above ground floor and in any position.

Supply only integral water proofing compound.

M&L for PCC 1:5:10 type E-2 (using 40mm graded crushed stone aggregate) filling foundation and mass cove in sunken floor all as directed.

M&L for 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in sub base for receiving the floor finishes complete all as specified.

Taking down cement plaster of any description built in cement mortar of any description as specified

M&L for 12mm thick rendering with ready mix mortar on brick or concrete surfaces other than fair surface, finished the surfaces even and smooth without using extra cement as specified.

All as per item No 19 above but 5mm thick on ceiling in CM 1:3

M&L for 15mm thick rendering with ready mix mortar on fair faces on brick or concrete surfaces fair finished the surfaces even and smooth complete all as specified & directed. (Note : WPC shall be measured and paid separately).

M&L for preparation of new plastered surface and finishing walls with acrylic smooth exterior paint of required shade (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) all as specified and directed.

M&L for preparation of new plaster surface of ceiling and applying three coats of white wash complete all as specified & directed.

Preparation of new plastered surfaces and applying two coats of oil bound distemper (of approved shade) on walls over primer chalk whitening on plastered surfaces complete all as specified.

M&L for complete removal of existing treatment with machincal scrapper and finishing walls with acrylic smooth exterior paint of required shade (two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) all as specified and directed by Engineer-in-Charge.

M&L for applying one coat of OBD on old decorated wall surface including preparation of surfaces complete all as specified.

M&L for applying one coat of white wash on old treated ceiling surfaces complete al as specified.

M&L for preparation of wooden surface exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of primer all as directed.

All as per Srl item No 28 above but applying two coats of synthetic enamel paint over one coat of red oxide on steel surface complete all as specified and directed.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter for the chowkat) all as directed.

All as per Srl item No 30 above but exc 1.50sqm but n.exc 4.00 Sqm.

Taking down shutter of any description exc 1.00 Sqm but n.exc 2.00 Sqm.

S&F pressed steel frame for doors with one or more rebate including necessary fixing lugs, hinges, lock, strike plate etc complete of size 105x60mm all as spd including two coats of painting over a shop coat of primer all as directed.

S&F pressed steel frames of size 125 x 60mm, for doors, one or more rebates including necessary fixing lugs, hinges, lock strike plate and filling of chowkats with PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate), tarring and sanding to inner surface (surface in contract with concrete/ brick surface) of chowkats complete all as specified and directed.

M&L for cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) in hold fast and for doors all as specified & directed.

S&F 30mm thick factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rails, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, complete all as specified and directed.

S&F glazed and skelton shutters 30mm thick of 2nd class hard wood open rebated and prepared to receive gauge & glass etc with edge of sash bar and number edges of framing plain chamfered beads for securing glass etc size of members of shutters as spd SSR Part-I & section 8 clause 8.23 & (b) complete all as specified.

S&F 32 mm thick both side laminated flush door shutter, veenered face complete all as specified and directed by Engineer-in-Charge.

S&F MS framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., and similar work incl primer conforming to FE-410-0 or FE 310-0 complete all as specified and directed.

M&L in repair for prelaminated particle board size 18/19mm thick, interior grade, prelaminated one side with decorative choice lamination &other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

S&F continuous (piano) hinges,mild steel, bright finish or electro galvanised complete all as specified and directed. width of flaps (when open) 40mm all as directed.

S&F 150 mm hasp and staple, safety type,brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified & directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm complete all as specified & directed.

S&F aluminium anodized barel tower bolt of extruded section 150mm long ISI mark all as specified and directed.

All as per Srl item No 49 above but 250mm long ISI mark all as specified and directed.

S&F aluminium alloyed handle cast type anodized of size 100mm long ISI mark all as specified and directed.

All as per Srl item No 46 above but 150mm long ISI mark all as specified and directed.

S&F for butt hinges med weight cold rolled mild steel 100mm size all as specified and directed.

S&F 300mm, mild steel ordinary rat tail rod pattern springs, including roller and roller plate complete. (Note : Repair required on steel door frame, welding to be carried out or necessary alternative arrangements to be done all as specified & directed).

S&F in repairs 300mm long ISI mark aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified.

S&F sheet glass 3mm thick ordinary quality, fixed with oil putty all as specified and directed.

S&F figured glass pin headed type glazing with oil puty glass 3mm thick, fixed with oil puty in square n. exe 0.5 sqm in each pane.

Taking down steel window/ventilator(with shutter) any size

S&F steel window 1.25mm thick box type(primer coated) ERW hollow P section of size 60mmX25mm double rebated comprises guaged skelton & glazed shutter including guard bar ERW sec 50mmX20mm and 1mm thick with two openable leaf consisting of two nos sash bar of T-section 20mmX3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1(four Nos for each window) including following fitting welded to frame shutter:-(i) Hold fast,150mm long of 12mmX3mm made to shape-04 Nos per window (ii) Handle of Z section 20mmX25mm,100mm long- 01Nos per window (iii) MS Tower bolt 150mm long-02 Nos per window (iv) Z sec 20mmX25mm,100mm long stopper -01 Nos per window (v) Cleat 55mm long of hollow square 15mmX12mm-02 Nos per leaf (vi) Fabrication & fixing arrangements as Drg No CEJZ/ TD-06-07. (vii) MS guard bar 12mm square bars @ 150 mm C/C fixed horizontlly.

S&F MS box type ventilator fixed type with glazing bar without wire gauge and glass as per Drg No CEJZ / TD-1019 /08 sheet 1/3 to 3/3 dt 01 May 2008 with guard bar including priming coat complete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks all as specified and directed.

Taking up and down GI pipe15mm bore including fittings, connection all as specified and directed.

All as per Srl item No 57 above but 20mm bore of pipe.

S&F GI tubing 15mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings all as specified and directed.

All as per Srl item No 59 above but fixing only (old serviceable pipe re-used)

S&F GI tubing 20mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings all as specified and directed.

All as per Srl item No 61 above but fixing only (old serviceable pipe re-used)

S&F rotational moulded water storage tank of 500 ltr capacity (cylinderical vertical with closed top) hoisted and fixed in position including dismantling of old unserviceable water tank complete all as specified and directed.

S&F in repair bib taps 15mm dia chromium plated fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule all as specified and directed.

S&F in repair for 15mm bore stop valves, cast copper alloy, screwed down , high pressure, with crutch or butterfly handles , screwed both ends for iron pipe or for unions, fancy type, chromium plated with long shank and cup (concealed type) all as specified and directed.

S&F in repair for 15mm bore stop valves, cast copper alloy,screwed down,high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions all as specified and directed.

S&F in repair stop valve 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc all as specified and directed.

S&F CP shower rose 125mm size with swivel joint fancy type all as specified and directed.

S&F in repair 20 mm float ball brass valve high pressure with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe all as specified and directed.

S&F CP brass towel rail `D’ type 60 Cm long fixed to wall all as specified and directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR) ISI marked pipes single socketed of any length with rubber ring joints fixed to wall or floor all as specified & directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint fixed to walls or floor complete all as specified.

Dismantling of cast iron, PVC or SGSW drain pipes, jointed in cement mortar including taking out of trenches all as directed.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with integral foot rest with `P’ or `S’ trap including water connection to trap and flushing pipe, flushing cistern etc complete all as specified

S&F in repair PVC low level dual flushing cistern 08 to 10 ltr capacity with syphonic action PVC float valve ,brackets and 32 mm bore PVC flush pipe etc all as specified and directed.

S&F in repair flush pipe of polythylene of low or high density or PVC, 32mm dia for low level cistern all as specified and directed.

S&F in repair vitreous china wash hand basin, white, flat back, size 630x450mm excluding taps,waste,chain and plug and porcelain stopper but including brackets all as specified and directed.

S&F in repair pillar taps, cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe all as specified and directed.

S&F in repair waste coupling 32mm dia of PTMT (half or full threaded). (Minimum weight 32mm - 45gms).

S&F PVC waste pipe 32mm dia 600 to 750mm long fixed to wash fitting of wash basin/ urinal all as specified and directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm all as specified and directed.

S&F PVC (SWR ) bends 110 mm bore any radius.

S&F PVC (SWR ) bends 75 mm bore any radius.

S&F PVC (SWR) junction single, ( T) equal or unequal with access door all as specified & directed.

M&L for PVC (SWR ) floor trap 100/75 mm plain with grating incl jointing with solvent cement all as specified and directed.

S&F stack clamps (100 mm pipe) out of 50x5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof all as specified and directed.

All as per Srl item No 87 above but 75 mm bore.

Demolition of brick work built in cement mortar/ cement lime mortar all as specified and directed.

M&L for brick work with sub class 'B' brick straight curved on plan exc 6m mean radius built in CM 1:4 slightly rounded as wedged shaped all as specified and directed.

S&F in repair cutrain rod 20mm dia of anodised aluminium alloys with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug including taking down existing curtain rod complete all as specified and directed.

S&F in repair kitchen sinks with drainage board made of stainless steel 1 mm thick with plugs, washers,CP coupling and wastes;including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm including fittings arrangement complete all as specified and directed

S&F in repair stop valve 15mm dia cast copper alloy chromium plated with long shank and cup concealed cock type all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n. exc 10 sq m on plan and not exc1.5 m in depth and getting out,all as specified & directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. all as specified & directed.

Removing excavated material n exc. 50m and depositing where directed at a level n. exc 1.5 m above the starting point all as specified & directed.

Demolition and breaking up old unserviceable drain pipes (salt glazed stone ware, AC or Reinforced concrete)150 mm bore at any depth set in cement mortar including PCC bed complete all as specified & directed.

M&L for PCC 1:4:8 type D2 (using 40 mm graded crushed stone aggregate) in concrete bed to drain pipes including packing under,and haunching against the sides of pipes after they are laid and tested complete all as specified & directed.

Supplying, laying in trenches, jointing and testing reinforced cement concrete pipes, class NP3, size 150mm dia laid and jointed, complete with collars at any depth over PCC bed complete all as specified and directed by Engineer-in-Charge.

M&L for PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) filling/ mass concrete etc foundation of manholes complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in coping, benching, apex stone, bed plate, kneelers complete all as specified.

M&L for precast RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as cover slab for manholes and similar work etc complete all as specified.

M&L for coloured chequered cement concrete tiles with grey cement and no pigment, 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate ), 75 mm thick, as in sub base of floor finishing even & fair complete all as specified and directed.

M&L for TMT mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including, mild steel wire(annealed) not less than 0.9mm dia or securing with clips all as specified & directed.

All as per Srl item No 105 here-in-before but 6 to 10mm dia.

M&L for broken stone or boulders hardcore of gauge n. exc 63mm, deposited, spread and levelled in layers n. exc 15cm thick, watered and rammed to a true surface specified and directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers n. exc. 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for brick work with fly ash, old size bricks, straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and directed.

M&L for RCC M-25 design mix (using 20 mm graded crushed stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M-25 Desgin mix (using 20 mm graded crushed stone aggregates) as slab supported on walls, beams and columns in floor, roofs, landings, balconies, canopies, deck slabs and in shelves and like complete all as specified and directed.

All as per Srl item No 111 above but in chajja , lintel beams and like complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and beams; and similar work; vertical or to batter rough finished surface flat complete all as specified and directed.

M&L for formwork to sides of pillars,posts, struts, piers, columns, beams and stanchions and like rough finished surfaces, square, rectangular or polygonal complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, chajja, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams etc complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (horizontal or sloping) complete all as specified and as directed.

M&L for 15 mm thick cement plaster in CM (1:3) using WPC on RCC roof slab complete all as specified and directed by Engineer-in-Charge. Note -WPC shall be measured and paid separately.

S&F 2nd class hard wood glazed and skeleton shutters, 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a) ; supplied and fitted to chowkats complete all as specified and directed.

S&F flush shutters 35 mm thick, solid core construction , with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty/ bead in square not exc. 0.5sqm in each pane complete all as specified and as directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and as directed.

S&F aluminium alloy anodised, sliding door bolt 300mm long, with hasp, staple ( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F spring for door, 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed .

M&L for 15mm thick cement plastering in CM 1:6 on brick or concrete surfaces, fair surface, finished the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick cement plastering in CM 1:4 on brick surfaces other than fair faces, finished the surfaces even and smooth with using extra cement complete all as specified and directed.

M&L for preparation of new plaster surface and applying two coats of cement base paint complete all as specified and directed.

S&F cutrain rod 20mm dia of anodised aluminium alloys with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug complete all as specified and directed.

M&L for 75mm thick cement cocnrete 1:3:6, type B-2 (40mm graded crushed stone aggregate) as in plinth protection finishing the surface even and fair laid in alternative bays not exceeding 3.0m in length complete all as specified and as directed.

Surface excavation n. exc 30cm deep and averaing 15cm deep and getting out any type of soil

M&L for prepartion new surface and applying two coats of aluminium paint over APP membrane all as specified and directed

M&L for 40mm thick cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in flooring complete all as specified.

S&F rotational moulded polyethylene 3-layer water storage tank of 1000 ltr capacity, white (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified & directed.

S&F bib taps 15mm dia cast copper alloy chromium plated fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule all as specified and directed.

M&L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square of surface area complete all as specified and directed.

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square of surface area complete all as specified and directed.

M&L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square of surface area complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for 60mm thick machine pressed pre cast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of M-35 grade with grey cement and pigment complete all as specified and directed.

M&L for applying one coat of oil bound distemper on old decorated wall surface including preparation of surfaces complete all as specified.

M&L for applying one coat of white wash on old treated ceiling surfaces complete al as specified.

Taking down chowkats with shutter n. exc 1.50 sqm each (without taking off shutter for the chowkats complete all as specified and directed.

All as per Srl item No 141 above but exc 1.50 sqm but n. exc 4.00 sqm.

Taking down shuttert of any description exc 1.00 sqm but n.exc 2.00 Sqm.

S&F pressed steel frame for doors with one or more rebate including necessary fixing lugs, hinges, lock, sall as specified including two coats of painting complete all as specified and directed.

E/M PORTION M&L for point wiring with PVC insulated and PVC unsheathed multistranded FRLSH copper conductor cable of size 1.5 Sqmm including concealed PVC conduit with fittings and making good to the disturbed surfaces with continuous earth wire of copper 1.5 sqmm dia to common earth including provn of 3mm thick plastic laminated sheet of appropriate size and fixing on CI/MS boxes for mounting of accessories like switch sockets and regulators etc. complete all as specified for One light / Fan/ bell point controlled by one way switch

All as per Srl item No 145 here-in-before but one 5 pin socket outlet 5 amps on same board.

All as per Srl item No 145 here-in-before but one 5 pin socket outlet on independent board.

All as per Srl tem No. 145 here-in-before but wiring with 2.5 sqmm FRLSH for one socket 16A multipin on independent board.

S&F in replacement of LED tube light fitting wall mounted with single side connection polycarbonate LED batten with aluminium housing and integrated electronic driver of capacity 20W, four feet and connection with PVC insulated twin core 23/0.0076 twisted copper cable from ceiling rose to tube light fitting, complete all as specified and directed.

S&F switch piano flush type single pole one way 5/6 amps complete all as specified and directed.

S&F socket outlet 3 pin 5 amps flush type complete all as specified and directed.

S&F switch flush type 15 amp single pole one way complete all as specified and directed

S&F socket outlet 3 pin 15 amp flush type complete all as specified and directed.

S&F lamp holder, PVC body angle type including 9 watt LED bulb polycarbonate body complete all as specified and as directed.

M&L for ceiling rose, surface bakelite 65x50 three terminal/ phase PVC polycarbonate isolated body complete all as specified and directed.

S&F in repair sheet metal enclosure for DB’s when MCB’s to be used of 240 volt 4 way SPN double door complete all as specified and directed. (Note :- All the connection of incoming and out going wire in MCB will be made with thimble with suitable size as directed).

S&F in repair MCB single pole 6 amps to 32 amps, complete all as specified and directed.

All as per Srl item No 157 here-in-before but single pole and neutral 6 amps to 32 amps complete all as specified and directed.

S&F exhaust fan, steel body AC single phase 230V of size 300mm sweep with, blades and frame and louvers including making suitable hole in wall complete all as specified and directed.

S&F in replacement GI pipe bracket made out of GI pipe light grade 32 mm bore and bent to shape 1.5m long, MS clamps made out of MS flat iron of size 32x 6mm thick with nuts, bolts and washers complete including dismentling the existing GI pipe bracket and drilling of holes for nuts and bolts etc complete all as specified and directed.

S&F LED street light fitting 35 Watt 230V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

S&F in replacement of fan regulator electronic type 5 step 100 watts, 240 volt and connecting complete all as specified and directed.

Supply and fixing ceiling fan 1200 mm sweep size BEE energy efficient 5 star rated powered with above BLDC technology conforming to latest BIS licensing and IS specification which consumes less than 50% of the power as compare to conventional type fans,power consumption 32 to 35 watt RPM 370+25% service valve 6.0 Air Delivery in CMM 200 ,down rod all including connection with 3 core 0.75 sqmm PVC insulated but unseathed FRLSH cable with multistandard copper conductor IS 694 marked from celing to fan complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sqmm 2 core complete al as specified and directed.

Supply and laying brick common burnt sub class "B" old size for protection of cable laid in trenches for under ground cable all as specified.

M&L for sand cushioning in trenches using fine sand to under ground cable, laid in two layers 15cm before laying the cable and 8cm after laying the cable complete all as specified

Taking down carefully aluminium/ copper point wiring for light, fan, bell, socket of point complete fiitings such as switches, ceiling roses, pendents, regulator socket etc complete at site and making goods disturbed surfaces of walls, floors etc complete all as specified and directed.

All as per serial item No 167 here-in-before but one light point controled by two way switches.

All as per serial item No 167 here-in-before but wiring with 2.5 sqmm FRLSH copper wire including earth wire 2.5 Sqmm of copper for 15 Amps 3 pin socket outlet.

M&L for sub main wiring with two runs of single core multi stranded PVC insulated, copper conductor, grade 1100 Volt, FRLSH cable of size 6 sqmm (red for phase and black for neutral) including PVC conduits not less than 1.2 mm thick and 25mm dia and 6 sqmm multistranded copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete including taking down old unserviceable wiring complete all as specified and directed. Note :- (a) Cost of making good the disturbed surface plastering/ filling putty alongwith matching with the existing surface is deemed to be included in the quoted rate by contractor. (b) Three run of cable alongwith PVC conduit together shall be measured as single run.

S&F switch piano 2 way 5A complete all as specified and directed.

S&F wall /ceiling mounting LED 9/10 watt tube light fitting complete with all acessories 1x9 Watt LED , with CCT of 6000k suitable for domestic application, 240 Volts, 50 Hz, and internally pre-wired with 1.5 sqmm twin twisted flexible cable copper conductor and connection complete all as specified and directed.

S&F decorative 9W, LED wall mounting fittings complete set including 9W LED lamp 9 Watt polycarbonate type B-22 complete all as specifed and directed.

S&F PVC insulated sheathed copper wire 1.5 sqmm FRLSH single core 1100 volt for inverter connection in same conduit all as specified and directed

S&F fan regulator electronic type 5 step 100 watts, 240 volt and connecting complete all as specified and directed.

S&F bell, AC, 230 volts, single pole complete all as specified and directed.

S&F bell push flush type 6 Amp complete all as specified and directed.

S&F in repair sheet metal enclosure for DB’s when MCB’s to be used of 240 volt 8 way with 200 amps rated bus bar SPN double door complete all as specified and directed. (Note :- All the connection of incoming and out going wire in MCB will be made with thimble with suitable size as directed).

M&L for replacement of distribution board made out of CRCA sheet DB vertical type double door TPN 4 Way MS sheet including fixing to wall, cutting chases, grounting and necessary patch work and white wash to match with the existing including making connections all as directed containing the folowings:- (a) MCCB 4 pole 63 amps 16 KA breaking capacity with thermal release: 01 No (In coming). (b) Bus bar made out of aluminium duly insulated wire adhesive tape RYB & black :4 Nos. (c) MCB SPN 40 Amp- 4 Nos, MCB SP 40 Amp- 04 Nos (out going). (d) Connection from MCCB to bus bar will be made with aluminium strip of suitable size as directed. (Note :- All the connection of incoming and out going wire in MCCB and MCB will be made with thimble with suitable size as directed).

M&L for earthing complete with galvanised steel earth plate electrode 60cmx60cmx 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point including testing on completion including watering GI pipe 20mm bore medium grade, 15mm bore light grade GI pipe for protection of earth lead including provision of concrete pit in PCC (1:3:6) type C-1, pre-cast RCC (1:2:4) MS bar funnel & wire mesh, excavation and earth work in any type of soil including dismantling existing earthing complete all as specified & directed by Engr-in-charge.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sqmm 3.5 core complete al as specified and directed.

M&L for GI tubing light grade fixed along the pole/under road/along the wall of size 40 mm bore with necessary clamps all as directed.

A Schedule of Credit for old/unserviceable demolished/ dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit Rs. 53,490/ - from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

GORAYA AND CO (BID ID -3475581)

AVTAR SINGH RAJU (BID ID -3483324)

BISHAN DASS (BID ID -3483384)