Loading…
Loading…
Tender Value
₹1.7 Cr
EMD Value
₹3.3 L
Closing Date
10 Aug 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
GENERAL
24 conditions · 5 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
(a) Attested Certificates(s) issued by Executive or Nominated Authority of the government Departments or Semi-Government/Public Sector Undertakings for the value of the work done for them during the qualifying period including current financial year certifying the bill amounts paid Agreement-wise and Date-wise or attested photo copy of such certificate. Such certificates will be accepted only from Govt. / Govt. bodies / PSUs authorities. Certificates issued by Private Bodies will not be considered.
NOTE: (i) Financial Year shall normally, be reckoned as 1st April to 31st March of the Next Year. However, for Turnover Criteria, the Financial Year as applicable to the Company /Tenderer is to be considered, if it defers from the above. (ii) Current Financial year is reckoned as the incomplete Financial year in which the date of tender submission falls. (iii) Chartered Accountant statements duly indicating yearly receipts will not be considered until and unless backed by Audited Balance Sheets or Provisional Balance sheet. (iv) (v) If the tender is not accompanied by the certificate(s) in support of financial eligibility as above, the tender shall be rejected. No post-tender correspondence will be entertained.
If JV firms are allowed to participate; Financial eligibility of the JV Firm shall be adjudged based on satisfactory fulfillment of the Para No.17.15.2 of J.V guide lines of IRSGCC April - 2022 [with up to date correction slip].
Definition of Similar Nature of work : (i) Any civil Engineering work (Value of component in tender is Rs. 91,20,931), (ii) Any Building work/concrete work (Value of component in tender is Rs. 75,07,301) (Note: Single/ Separate completed work of minimum required value shall be considered for fulfilment of technical eligibility criteria for above two different components as per para 10.1 of GCC 2022).
78 conditions · 29 needing a document upload
Uploading of Proforma -18 attached with Tender document (Certificate signed by Tenderer and Chartered Accountant), w he n balance sheet for the first previous year is yet to be prepared/ audited.
Proforma-16 for self-certificate in regard to meeting the Minimum Local Content requirements as per Make in India Policy for Procurement order value less than of Rs. 10 Crores. OR Proforma-17 for Certificate from the statutory auditor or cost auditor of the company (in the case of companies) or from a practicing cost accountant or practicing chartered accountant (in respect of suppliers other than companies) giving the percentage of Local Content as per Make in India Policy for Procurement Order Value more than Rs.10 Crores. Provisions of Make in India Policy 2017 (revised during 2024 vide Department for Promotion of Industry and Trade, Ministry of Commerce and Industry's letter No. P-45021/2/2017-PP (BE-II)-Part(4)Vol.II dated 19.07.2024) issued by Govt. of India, as amended from time to time, shall be followed for consideration of tenders.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
(i) The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. (ii) documents shall be submitted according to clause 14 of IRGCC 2022:
This tender complies with PUBLIC PROCUREMENT POLICY ORDER-2017 dated 15.06.2017. Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions. Provisions of Make in India Policy 2017 issued by Govt. of India, as amended from time to time, shall be followed for consideration of tenders.
The General Conditions of Contract governing the performance of the works covered by this tender are the Indian Railway Standard General Conditions of Contract [IRSGCC] as amended from time to time up to date. A soft copy of the Indian Railway Standard General conditions of Contract is uploaded in the attached documents to the tender for reference. Hard copy of IRSGCC (with up-to-date correction slip) may be perused in the office of the Principal Chief Engineer Officer/ South Western Railway / Hubballi - 580020. The tenderer/s is/are deemed to have kept himself/themselves fully Informed of the provisions of the IRS General conditions of Contract including all corrections and Amendments issued up to date while submission of offer and any claim that he/they is/are not aware of any amendment or correction slip to the IRSGCC shall not be entertained.
STUDY OF DRAWINGS AND LOCAL CONDITIONS: The drawings for the works can be seen in the office of the General Manager/Divisional Railway Manager. It should be noted that these drawings are meant for general guidance only and Railway may suitably modify them during the execution of work according to the circumstances without making the Railways liable for any claims on account of such changes. If there is any variation between the description in the tender and the detailed plans, the Engineer-in-Charge will operate the correct description and his decision is final and binding on the tenderer/ Contractor. The Tenderer/Contractor is required to inspect the sites of works and acquaint himself with the site conditions, availability of approaches for transporting of men and materials, space and other factors relating to the works, availability of labour, electricity and water, etc., before quoting his rates. The extent of lead and lift involved in the execution of works and any difficulties involved in the execution of work should also be examined before formulating the rates for complete items of works described in the schedule. The Tender submitted will be deemed to have been made after such inspection.
DRAWINGS FOR WORKS: The percentage rates for the schedule items and itemized rates for the non-scheduled items quoted by the tenderer as may be accepted by the railways will, hold good irrespective of any changes, modifications, alterations, additions, omissions in the locations of structures and detailed drawings, specifications and/or the manner of executing the work. It should be specifically noted that some of the detailed drawings may not have been finalized by the Railway and will, therefore, be supplied to the contractor as and when they are finalized on demand. No compensation whatsoever on this account shall be payable by the Railway Administration. No claim whatsoever will be entertained by the Railway on account of any delay or hold up of the works arising out of delay in approval of drawings, changes, modifications, alterations, additions, omission and the site layout plans or detailed drawings and design and/or late supply of such material as are required to be arranged by the Railway or due to any other factor on Railway Accounts.
Manual tenders, supporting documents etc., sent by Post/FAX/Courier or in Person SHALL NOT BE ACCEPTED.
All requisite documents are to be properly submitted online only and the bidders should ensure that the content of the documents uploaded is distinctly legible /readable.
CORRIGENDUM NOTICE ON IREPS: Railway may modify the tender document by issuing online corrigendum through "www.ireps.gov.in" 15 days prior to the tender closing date. For the purpose of CORRIGENDUM in the tender, NIT period is splitted as under: (a) ADVERTISEMENT PERIOD: The time during which all information pertaining to tender shall be available but offers cannot be submitted (b) OFFER SUBMISSION PERIOD: 15 days prior to closing of tender, during which tenderers can submit their offer.
If the Bid of a Tenderer is seriously unbalanced in relation to the Engineer's estimate of the cost of work to be performed under the contract, the Railways may require the tenderer to produce detailed price analysis for any or all items of the Tender Schedule, to demonstrate the internal consistency of those prices with the construction methods and schedule proposed.
No Technical and Financial credentials are required for tenders having value up to Rs 50 lakh. For tenders valuing more than Rs. 50.00 lakh: The offer of Tenderer(s) who do not enclose Experience Certificate & Turnover Certificate with requisite details, and supporting documents along with their Tender to establish their credentials shall be summarily rejected, even though they are working contractors or contractors on approved list.
The offer shall be evaluated only from the certificates/documents submitted along with the tender offer.
Any Certificate /Documents offered / submitted /received after the tender opening shall not be given any credit and shall not be considered.
Attestation of documents may be self attested or attested by a Gazetted Officer.
Railwayreservestherighttoverifythe authenticityofthe documents/information furnished.
IRSGCC para 6.0 of part-I (a)(ii) Tenderers will examine the various provisions of The Central Goods and Services Tax Act, 2017(CGST)/ Integrated Goods and Services Tax Act, 2017(IGST)/ Union Territory Goods and Services Tax Act, 2017(UTGST)/ respective state's State Goods and Services Tax Act (SGST) also, as notified by Central/State Govt.& as amended from time to time and applicable taxes before bidding. Tenderers will ensure that full benefit of Input Tax Credit (ITC) likely to be availed by them is duly considered while quoting rates. (a)(iii) The successful tenderer who is liable to be registered under CGST/IGST/UTGST/SGST Act shall submit GSTIN along with other details required under CGST/IGST/ UTGST /SGST Act to railway immediately after the award of contract, without which no payment shall be released to the Contractor. The Contractor shall be responsible for deposition of applicable GST to the concerned authority. (a)(iv) In case the successful tenderer is not liable to be registered under CGST/IGST/UTGST/ SGST Act, the railway shall deduct the applicable GST from his/their bills under reverse charge mechanism (RCM) and deposit the same to the concerned authority. (b) When work is tendered for by a firm or company, the tender shall be signed by the individual legally authorized to enter into commitments on their behalf. (c) The Railway will not be bound by any power of attorney granted by the tenderer or by changes in the composition of the firm made subsequent to the execution of the contract. It may, however, recognize such power of attorney and changes after obtaining proper legal advice, the cost of which will be chargeable to the Contractor.
Increase/decrease of TAXES: if rates of existing GST or cess on GST for Works Contract is increased or any new tax /cess on Works Contract is imposed by Statute after the date of opening of tender but within the original date of completion/date of completion extended under clause 17 & 17A and the Contractor thereupon properly pays such taxes/cess, the Contractor shall be reimbursed the amount so paid. Further, if rates of existing GST or cess on GST for Works Contract is decreased or any tax/cess on Works Contract is decreased / removed by Statute after the date of opening of tender, the reduction in tax amount shall be recovered from Contractor's bills/Security Deposit or any other dues of Contractor with the Government of India.
Fixed Deposit Receipts (FDRs) submitted after award of tender towards Security Deposit/Performance Guarantee should be with automatic renewal facility only.
CONSORTIUM AGREEMENTS AND MOUS SHALL NOT BE CONSIDERED FOR PARTICIPATING IN THIS TENDER.
Tenderer(s) shall note that conditional/alternate offer will not be considered and will summarily be rejected, even though such condition makes them as the lowest tenderer.
Shramik kalyan While processing payment of any 'On Account Bill' or 'Final Bill' or release of 'Advances' or 'Performance Guarantee / Security deposit', contractor shall submit a certificate to the Engineer or Engineer's representatives that "I have uploaded the correct details of contract labours engaged in connection with this contract and payments made to them during the wage period in Railway's Shramik kalyan portal at 'www.shramikkalyan.indianrailways.gov.in' till ____Month, ____Year.
Date of inviting tender shall be the date of publishing tender notice on IREPS website if tender is published on website or the date of publication in newspaper in case tender is not published on website.
Sr.DEN/North/SBC sec: SW-I: Proposed Extension of PF-1 and PF-2 for a length of 90.00 mtr at Thondebhavi (TDV) station in Bengaluru - Dharmavaram Section under ADEN/Hindupur Sub-Division. SW-II: Yelahanka : Construction of Crew lobby on 3rd floor of existing station building at Yelahanka under ADEN/Yesvantpur Sub- Division. Maintenance period is 3 years
18SBC26OF16-07-26Item-09
18SBC26OF16-07-26Item-09
Open
Works - General
9 Months
Dharwad, Karnataka
₹0
₹3.3 L
16 Jul 2026
16 Jul 2026
27 Jul 2026
261 items across 6 schedules · ₹65,61,655.24 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| CARRIAGE OF MATERIALS | — | — | — | — | |
| By Mechanical Transport including loading, unloading and stacking | — | — | — | — | |
| 1 | Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. | cum | 20 | 494.1 | 9,882 |
| EARTH WORK | — | — | — | — | |
| General | — | — | — | — | |
| Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. | — | — | — | — | |
| 2 | All kinds of soil | cum | 300 | 177.5 | 53,250 |
| Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. | — | — | — | — | |
| 3 | Ordinary rock | cum | 35 | 498.9 | 17,461.5 |
| 4 | Hard rock (requiring blasting) | cum | 35 | 874.4 | 30,604 |
| 5 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. | cum | 990 | 700.5 | 6,93,495 |
| CONCRETE WORK | — | — | — | — | |
| CEMENT CONCRETE (CAST IN SITU) | — | — | — | — | |
| Centering and shuttering including strutting, propping etc. and removal of form work for : | — | — | — | — | |
| 6 | Foundations, footings, bases for columns | Sqm | 405 | 392.15 | 1,58,820.75 |
| MISCELLANEOUS | — | — | — | — | |
| Providing and laying in position ready mixed or site batched design mix cement concrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete. | — | — | — | — | |
| All works upto plinth level : | — | — | — | — | |
| 7 | Concrete of M15 grade with minimum cement content of 240 kg /cum | cum | 35 | 8,986.15 | 3,14,515.25 |
| 8 | Concrete of M25 grade with minimum cement content of 300 kg /cum | cum | 160 | 9,439.05 | 15,10,248 |
| REINFORCEMENT CEMENT CONCRETE | — | — | — | — | |
| PRE-CAST RCC | — | — | — | — | |
| 9 | Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). | cum | 55 | 10,585.9 | 5,82,224.5 |
| STEEL REINFORCEMENT | — | — | — | — | |
| Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. | — | — | — | — | |
| 10 | Thermo-Mechanically Treated bars of grade Fe-500D or more. | Kg | 3715 | 107.85 | 4,00,662.75 |
| STONE WORK | — | — | — | — | |
| RANDOM RUBBLE MASONRY | — | — | — | — | |
| Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : | — | — | — | — | |
| 11 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 32 | 7,311.25 | 2,33,960 |
| STEEL WORK | — | — | — | — | |
| General | — | — | — | — | |
| Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. | — | — | — | — | |
| 12 | Hot finished welded type tubes | Kg | 70 | 194.4 | 13,608 |
| 13 | Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. | Kg | 470 | 97.2 | 45,684 |
| FLOORING | — | — | — | — | |
| TILE FLOORING | — | — | — | — | |
| Chequered precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). | — | — | — | — | |
| 14 | Light shade pigment using white cement | Sqm | 240 | 1,402 | 3,36,480 |
| CERAMIC GLAZED TILES | — | — | — | — | |
| 15 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. | Sqm | 20 | 1,096.55 | 21,931 |
| ROOFING | — | — | — | — | |
| RAIN WATER SPOUT AND PIPE | — | — | — | — | |
| Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. | — | — | — | — | |
| 16 | 110 mm diameter | Metre | 40 | 377.4 | 15,096 |
| 17 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in- charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. | Sqm | 530 | 738.65 | 3,91,484.5 |
| Providing and fixing of Pre-coated colour or mill finish Aluminium Roofing Accessories in 0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO designation)] For colour, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/tapping SS screws of size 6 x 50 mm with 3 mm thick EPDM seal and SS plain washer complete : | — | — | — | — | |
| 18 | Precoated/mill finish aluminium Gutter (600 mm over all girth) | Metre | 50 | 1,808.65 | 90,432.5 |
| FINISHING | — | — | — | — | |
| CEMENT PLASTER (IN FINE SAND) | — | — | — | — | |
| 12 mm cement plaster of mix : | — | — | — | — | |
| 19 | 1:6 (1 cement: 6 fine sand) | Sqm | 35 | 333.35 | 11,667.25 |
| POINTING ON STONE WORK | — | — | — | — | |
| Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) : | — | — | — | — | |
| 20 | Flush/ Ruled pointing | Sqm | 200 | 385.4 | 77,080 |
| EXTERIOR FINISHING | — | — | — | — | |
| Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : | — | — | — | — | |
| 21 | Two or more coats on new work | Sqm | 70 | 155.9 | 10,913 |
| Painting with aluminium paint of approved brand and manufacture to give an even shade . | — | — | — | — | |
| 22 | Two or more coats on new work | Sqm | 870 | 146.8 | 1,27,716 |
| Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. | — | — | — | — | |
| 23 | Two coats | Sqm | 265 | 142.8 | 37,842 |
| DISMANTLING AND DEMOLISHING | — | — | — | — | |
| General | — | — | — | — | |
| Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. | — | — | — | — | |
| 24 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) | cum | 10 | 2,434.25 | 24,342.5 |
| 25 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. | cum | 7 | 3,551.25 | 24,858.75 |
| ROAD WORK | — | — | — | — | |
| CONCRETE PAVEMENTS | — | — | — | — | |
| 26 | Extra for providing and mixing hardening compound of approved quality as per manufacturer's specification in cement concrete. | Litre | 290 | 55.5 | 16,095 |
| MISCELLANEOUS | — | — | — | — | |
| 27 | Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in- charge and accordance with applicable specifications. | Sqm | 35 | 747.8 | 26,173 |
| 28 | Providing and laying C.C. pavement of mix M- 25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). | cum | 150 | 9,823.8 | 14,73,570 |
| WATER SUPPLY | — | — | — | — | |
| C.P.V.C. PIPES | — | — | — | — | |
| Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work | — | — | — | — | |
| 29 | 20 mm nominal dia Pipes | Metre | 35 | 274.3 | 9,600.5 |
| 30 | 25 mm nominal dia Pipes | Metre | 35 | 355.4 | 12,439 |
| 31 | 50 mm nominal dia Pipes | Metre | 70 | 794.25 | 55,597.5 |
| BRASS FITTINGS | — | — | — | — | |
| Providing and fixing brass bib cock approved quality : | — | — | — | — | |
| 32 | 15 mm nominal bore | Each | 10 | 353.25 | 3,532.5 |
| Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : | — | — | — | — | |
| 33 | 25 mm nominal bore | Each | 10 | 622.4 | 6,224 |
| 34 | 50 mm nominal bore | Each | 2 | 1,026.65 | 2,053.3 |
| PTMT FITTINGS | — | — | — | — | |
| Providing and fixing PTMT, push cock of approved quality and colour. | — | — | — | — | |
| 35 | 15 mm nominal bore, 98 mm long, weighing not less than 75 gms | Each | 20 | 112.8 | 2,256 |
| NEW TECHNOLOGIES AND MATERIALS | — | — | — | — | |
| NEW TECHNOLOGY ITEMS | — | — | — | — | |
| Providing and laying factory made Precast concrete solid blocks of 200 mm thickness of grade M10 made of C&D waste from approved manufacturer in superstructure above plinth level up to floor V level | — | — | — | — | |
| 36 | Cement mortar 1:6 (1 cement : 6 coarse sand) | cum | 20 | 9,844.65 | 1,96,893 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
bidcapacityformat-1-2.pdf
ATTACHMENT
GCCAPRIL2022_AllACS_upto11.pdf
ATTACHMENT
ACS-6.pdf
ATTACHMENT
ACS-5toGCC2022.pdf
ATTACHMENT
Instructionstobidders.pdf
ATTACHMENT
GCC2022ACS-3_20230426_1141401.pdf Advanced correction slip - 3
ATTACHMENT
Advance Correction Slip No.2
ATTACHMENT
GCCACS11_compressed.pdf
ATTACHMENT
ACS7.pdf
ATTACHMENT
JPOCablecuts.pdf
ATTACHMENT
Standardtenderdoc-6.1.pdf
ATTACHMENT
Proforma-161718.pdf
ATTACHMENT
ACS-9dated.09.01.2025.pdf
ATTACHMENT
acs10.pdf
ATTACHMENT
GCCACS.pdf
ATTACHMENT
NEFTForm.pdf
ATTACHMENT
IRGCCApril2022.pdf
ATTACHMENT
GCC2022ACS-3_20230426_1141401.pdf
ATTACHMENT
ACS-2toGCC-2022_2022-CE-1-CT-GCC-2022-POLICY_13.12.20221.pdf
ATTACHMENT
Order-deptforpromotionofindustryandtrade.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].