SPL REPAIRS FOR REPLACEMENT OF LT OVER HEAD LINE INTO LT UG CABLE AND OTHER MISC WORK AT OFFRS MESS AND OFFRS MD ACCN AREA AT MILITARY STATION ABOHAR.

Amount

Dismantling and taking out Prest ressed concrete pole/Steel of any size including breaking of PCC foundation and earth work etc and removal of debris where directed complete.

Dismantling stay assembly complete demolition of concrete, etc. and excavation measured separately

Dismantling of ACSR or AAC conductors

Dismantling/taking down cross arms, bracings, support, clamp including nuts, bolts and washers complete.

Dismantling of insulators LT of any size for removal or refixing at site as directed.

Supply and lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 185 sq mm 3½ core including provision of LT cable path indicator CI round shape mentioning LT cable of Blue color paint fixed with 0.75 Mtr lenth angle iron of size 40x40x4 mm laying intervals 20 Mtr and refer laying of cable shall be compile with SSR Part -I Section 19.75.1 Note: Cable path indicators and end termination joints with aluminium lugs/thimbles deemed to include with quoted rates. Make:- Havells, Polycab, KEI, Grandlay.

All as per Srl item No. 6 here-in-before but size 120 sq mm 3½ core

All as per Srl item No. 6 but size 95 sq mm 3½ core

All as per Srl item No. 6 but size 70 sq mm 3½ core

All as per Srl item No. 6 but size 50 sq mm 3½ core

All as per Srl item No. 6 but size 35 sq mm 3½ core

All as per Srl item No. 6 but size 25 sq mm 3½ core

All as per Srl item No. 6 but size 16 sq mm 4 core

All as per Srl item No. 6 but size 25 sq mm 2 core

All as per Srl item No. 6 but size 16 sq mm 2 core

Supply, install, testing and commissioning of CPRI approved, factory made, LT panel board cubical, outdoor type, floor mounted double door, 3 phase, 4 wire 50 Hz, 415 volts . The panel board size 1.2 X 1.2 X 0.6 mtr shall be made 3.15 mm thick CRCA sheet load bearing members and 16 SWG (1.6 mm thick) for door covers and internal portions shall be powder coted both sides. Base frame of the panel shall be made of ICMC channel of size 50X50X6 mm, duly grouted on plateform made of brick work in CM (1:2:4), 15 mm thick plastering in CM (1:6) having minimum height 600 mm. The panel shall be provided with separate compartment of each switch gears with hinged door, including inter locking with switch gears. The panle board shall be suitable for AC, 415 volts, 50Hz, 3 Phase, 4 Wire supply completed with epoxy coated (500 Amp) rated high conductivity Aluminum bus bar supported with DMC/ AMC barriers and colour coated heat shirnkable sleve and F class insulator pre-wired with copper cable, 1100 volts of danger notice board on front of the panel and degree of protection is IP 54. The panel shall be complete with illustration such as LED phase indicating lamps and CTs including external aluminium strip of rating and rating of MCCBs including aluminium lugs to connected the cable etc. . (i) INCOMING: (a) MCCB 200A,415 Volts 4 pole, 25 KA-(Adj Thermal Mag sett)-01 (Incoming) (b) Indicator lamp LED type (set of three Red,Yellow,Blue)-01 set (ii) OUTGOING (c) MCCB-100A,3 Pole ,25 KA (d) MCCB-100A ,3 Pole ,25 KA (e) MCCB-100A, 3 Pole ,25 KA (f) MCCB-100A, 3 Pole ,25 KA (g) MCCB-4P-63A (h) MCCB-4P-63A (j) MCB-DP-40A (k) MCB-DP-63A (l) MCCB-100A (m) Aluminum bus bar 300 Amp, reqd length-04 nos (n) Digital Volt meter & Ammeter with suitable CT's each Note:- 1. Design/ drawing / BOM of the panel board showing the dimension incl accessories is to be obtained from panel board manufacturer / supplied an is to be got approved from GE before placing fianl order to the manufacturer / suppliers. 2. Anything missing out in the technical specification but technically required for efficient working is deemed to be included in qouted rates.

Supply, install, testing and commissioning of CPRI approved, factory made, LT panel board cubical, outdoor, type, floor mounted double door, 3 phase, 4 wire 50 Hz, 415 volts . The panel board size 1.2 X 1.2 X 0.6 mtr shall be made 3.15 mm thick CRCA sheet load bearing members and 16 SWG (1.6 mm thick) for door covers and internal portions shall be powder coted both sides. Base frame of the panel shall be made of ICMC channel of size 50X50X6 mm, duly grouted on plateform made of brick work in CM (1:2:4), 15 mm thick plastering in CM (1:6) having minimum height 600 mm. The panel shall be provided with separate compartment of each switch gears with hinged door, including inter locking with switch gears. The panel board shall be suitable for AC, 415 volts, 50Hz, 3 Phase, 4 Wire supply completed with epoxy coated (500 Amp) rated high conductivity Aluminum bus bar supported with DMC/ AMC barriers and colour coated heat shirnkable sleve and F class insulator pre-wired with copper cable, 1100 volts of danger notice board on front of the panel and degree of protection is IP 54. The panel shall be complete with illustraction such as LED phase indicating lamps and CTs including external aluminium strip of rating and rating of MCCBs including aluminium legs to connected the cable etc. (i) INCOMING (a) MCCB 315 A,415 Volts 4 pole, 36 KA-(Adj Thermal Mag sett)-01 No (b) Indicator lamp LED type (set of three Red,Yellow,Blue) (ii) OUTGOING (c) MCCB-100A ,3 Pole ,25 KA (d) MCCB-100A, 3 Pole ,25 KA (e) MCCB-100A, 3 Pole ,25 KA (f) MCCB-4P-63A (g) MCCB-4P-63A (h) MCB-DP-40A (j) MCB-DP-63A (k) MCCB-100A (l) Aluminum bus bar 500 Amp, reqd length-04 nos (m) Digital Volt meter & Ammeter with suitable CT's each ( 500+400) (n) Supply and fixing timer switch /Auto lux astro type (having longitude and latitude of Indian cities in memory 250 V single phase of 20 Amps rating with Three phase contactor fitted inside steel enclosure Note:- 1. Design/ drawing / BOM of the panel board showing the dimension incl accessories is to be obtained from panel board manufacturer / supplied an is to be got approved from GE before placing fianl order to the manufacturer / suppliers. 2. Anything missing out in the technical specification but technically required for efficient working is deemed to be included in qouted rates.

Supply, install, testing and commissioning of CPRI approved, factory made, LT panel board cubical, outdoor, type, floor mounted double door, 3 phase, 4 wire 50 Hz, 415 volts . The panel board size 1.2 X 1.2 X 0.6 mtr shall be made 3.15 mm thick CRCA sheet load bearing members and 16 SWG (1.6 mm thick) for door covers and internal portions shall be powder coted both sides. Base frame of the panel shall be made of ICMC channel of size 50X50X6 mm, duly grouted on plateform made of brick work in CM (1:2:4), 15 mm thick plastering in CM (1:6) having minimum height 600 mm. The panel shall be provided with separate compartment of each switch gears with hinged door, including inter locking with switch gears. The panle board shall be suitable for AC, 415 volts, 50Hz, 3 Phase, 4 Wire supply completed with epoxy coated (500 Amp) rated high conductivity Aluminum bus bar supported with DMC/ AMC barriers and colour coated heat shirnkable sleve and F class insulator pre-wired with copper cable, 1100 volts of danger notice board on front of the panel and degree of protection is IP 54. The panel shall be complete with illustration such as LED phase indicating lamps and CTs including external aluminium strip and rating of MCCBs including aluminium lugs to connected the cable etc. (i) INCOMING (a) MCCB 315 A,415 Volts 4 pole, 36 KA-(Adj Thermal Mag sett) (b) Indicator lamp LED type (set of three Red,Yellow,Blue) (ii) OUTGOING (c) MCCB-100A (d) MCCB-3P-63A (e) MCB-DP-63A (f) MCB-DP-63A (g) MCB-DP-40A (h) MCB-DP-40A (j) MCB-DP-40A (k) MCB-DP-40A (l) MCCB-DP-100A (m) Aluminum bus bar 500 Amp, reqd length-04 nos (n) Digital Volt meter & Ammeter with suitable CT's each (o) Supply and fixing timer switch /Auto lux astro type (having longitude and latitude of Indian cities in memory ) 250 V single phase of 20 Amps rating with Three phase contactor fitted inside steel enclosure Note:- 1. Design/ drawing / BOM of the panel board showing the dimension incl accessories is to be obtained from panel board manufacturer / supplied an is to be got approved from GE before placing fianl order to the manufacturer / suppliers. 2. Anything missing out in the technical specification but technically required for efficient working is deemed to be included in qouted rates.

Supply, install, testing and commissioning of CPRI approved, factory made, LT panel board cubical, outdoor, type, floor mounted double door, 3 phase, 4 wire 50 Hz, 415 volts . The panel board size 1.0 X 1.0 X 0.6 mtr shall be made 3.15 mm thick CRCA sheet load bearing members and 16 SWG (1.6 mm thick) for door covers and internal portions shall be powder coted both sides. Base frame of the panel shall be made of ICMC channel of size 50X50X6 mm, duly grouted on plateform made of brick work in CM (1:2:4), 15 mm thick plastering in CM (1:6) having minimum height 600 mm. The panel shall be provided with separate compartment of each switch gears with hinged door, including inter locking with switch gears. The panle board shall be suitable for AC, 415 volts, 50Hz, 3 Phase, 4 Wire supply completed with epoxy coated (150Amp) rated high conductivity Aluminum bus bar supported with DMC/ AMC barriers and colour coated heat shirnkable sleve and F class insulator pre-wired with copper cable, 1100 volts of danger notice board on front of the panel and degree of protection is IP 54. The panel shall be complete with illustration such as LED phase indicating lamps and CTs including external aluminium strip and rating of MCCBs including aluminium lugs to connected the cable etc. (i)INCOMING (a) MCCB 100 A,415 Volts 4 pole, 25 KA-(Adj Thermal Mag sett) (b) Indicator lamp LED type (set of three Red,Yellow,Blue) (ii) OUTGOING (c) MCCB - 3P -200A,25 KA - 04 Nos (d) MCB -4P - 63A,25KA (e) MCB-DP-40A (f) MCB-DP-63A (g) MCCB-3P-200A (h) Aluminum bus bar 200 Amp, reqd length-04 nos (j) Digital Volt meter & Ammeter with suitable CT's each ( 500+400) (k)Astronomical time switch complete with all accessories in built panel (l) Supply and fixing timer switch /Auto lux astro type (having longitude and latitude of Indian cities in memory ) 250 V single phase of 20 Amps rating with Three phase contactor fitted inside steel enclosure-01 No Note:- 1. Design/ drawing / BOM of the panel board showing the dimension incl accessories is to be obtained from panel board manufacturer / supplied an is to be got approved from GE before placing fianl order to the manufacturer / suppliers. 2. Anything missing out in the technical specification but technically required for efficient working is deemed to be included in qouted rates.

Supply, install, testing and commissioning of CPRI approved, factory made, LT panel board cubical, outdoor, type, floor mounted double door, 3 phase, 4 wire 50 Hz, 415 volts . The panel board size 1.0 X 1.0 X 0.6 mtr shall be made 3.15 mm thick CRCA sheet load bearing members and 16 SWG (1.6 mm thick) for door covers and internal portions shall be powder coted both sides. Base frame of the panel shall be made of ICMC channel of size 50X50X6 mm, duly grouted on plateform made of brick work in CM (1:2:4), 15 mm thick plastering in CM (1:6) having minimum height 600 mm. The panel shall be provided with separate compartment of each switch gears with hinged door, including inter locking with switch gears. The panle board shall be suitable for AC, 415 volts, 50Hz, 3 Phase, 4 Wire supply completed with epoxy coated (150 Amp) rated high conductivity Aluminium bus bar supported with DMC/ AMC barriers and colour coated heat shirnkable sleve and F class insulator pre-wired with copper cable, 1100 volts of danger notice board on front of the panel and degree of protection is IP 54. The panel shall be complete with illustraction such as LED phase indicating lamps and CTs including external aluminium strip of rating and rating of MCCBs including aluminium legs to connected the cable etc. (i) INCOMING (a) MCCB 315 A,415 Volts 4 pole, 36 KA-(Adj Thermal Mag sett) (b) Indicator lamp LED type (set of three Red,Yellow,Blue) (ii) OUTGOING (c) MCCB-3P-63A, 25 KA -02 Nos (d) MCCB-3P-40A, 25 KA -02 Nos (e) MCB -DP-40A - 03 Nos (f) MCB -DP-63A - 02 Nos (g) MCCB-3P-63 A, 25 KA (h) Aluminum bus bar 500 Amp, reqd length-04 nos (j) Digital Volt meter & Ammeter with suitable CT's each ( 500+400) Note:- 1. Design/ drawing / BOM of the panel board showing the dimension incl accessories is to be obtained from panel board manufacturer / supplied an is to be got approved from GE before placing fianl order to the manufacturer / suppliers. 2. Anything missing out in the technical specification but technically required for efficient working is deemed to be included in qouted rates.

M & L for preparation of old painted surfaces of LT panel size 2.0x1.5mx0.6m and applying spray painting with two coats of synthetic enamel paint over a coat of red oxide primer of existing color for outdoor/indoor panel board, outer & inner side and scraping out the old paint surfaces of existing panel boards complete all as directed by Engineer-in-charge including white wash to panel foundation/PCC base complete all as specified and directed.

Material and labor for removing serviceable cable duly testing the cable by the megger and taking down existing serviceable and relaying as specified such as relaying/rerouting and shifting the cable to laying as reqd at site complete all as specified and directed Note: 1. Taking down removal of the cable rates deemed to include in quoted rates. 2. Excavation,earth work and other necessary items for the relaying of the cable measured and paid separately under relevent items

M&L for removing bricks from trench for re use of serviceable bricks and re-laying old serviceable bricks of any type and size bricks, for cable protection in trenches laid dry and flat complete all as specified and directed by Engineer-in-Charge

M&L for taking down carefully street light fitting and bracket for re use to servicebile after minor repairs if any by replacing wire, connection terminals and nut, bolt washers and fix the street light and bracket with steel tubular pole by using necessary clamps,nut bolts and washers complete all as specified and directed. Note: Clamps,nut,bolt and washers for fixing street light bracket is measured and paid seprately with relevent items of the schedule

M&L in repairs for straight through cold shrink type joint 1100 Volt complete with jointing material and accessories suitable for 10 to 50 Sqmm 3.5 Core complete all as specified and directed by Engineer-in-Charge

M&L in repairs for Straight through cold shrink type joint 1100 Volt complete with jointing material and accessories suitable for 70 to 150 Sqmm 3.5 Core complete all as specified and directed by Engineer-in-Charge

S&F 1.5 sqmm 3 core, 1100 volt grade heavy duty cable, PVC insulated copper multistranded conductor, served with inner sheathing of PVC tape and overall PVC sheathed for making connection of street light from FRP junction box to street lights including provision of flexible pipe to conealed the copper wire from weather expose complete all as specified and directed by Engineer-in-Charge

M&L for Earthing for Panels complete with galvanized steel plate electrode of size 600x600x6.3mm thick buried directly in ground with earth pit not less than 2.25 meter deep below ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanized iron earth strip of size 25 x 4mm earth lead by means of nuts, bolts, check nuts, washers of galvanised iron as steel, protected by galvanized iron pipe 40mm bore (Medium grade) all as directed including cement concrete (1:3:6) type C-1 earth pit with precast RCC (1:1.5:3) type A-1 cover slab of size 42 x 42 x10cm thick reinforced with 8mm dia TMT bars @ 15 cm c/c both ways with 10mm dia mild steel round bar of 30 cm long, bent to shape as lifting handle, funnel, wire mesh, 20 mm bore galvanized iron pipe (medium grade) for watering, charcoal or coke and salt in alternate layers with necessary earth work in soft/loose soil complete all as shown in electrical plate No 3 of SSR Part I including testing on completion all complete as specified and directed.

Supply and install steel tubular swaged poles type 410 SP-31 ( 9.0 metres long) with MS base plate of size 300 X 300 X 6 mm thick at bottom , welded at center with through hole of 14 mm dia height of 300 mm above the coping, complete with including painting of poles with two coats of synthetic enamel paint over a coat of primer black and white/yellow strips 30CM wide each (05 Nos) up to 1.5 Mtrs height from coping & numbering of poles complete all as specified and directed. all as directed.

M&L for cement concrete in foundations, filling and mass comcrete type D2 1:4:8 with 40 mm graded stone aggrigate for foundation of pole etc complete all as specified.

M&L for providing PCC 1 : 3: 6 type C2 using 40mm graded stone aggregate as foundations, filling and mass concrete complete all as specified and directed

M&L for providing cement concrete type B1, 1:2:4 using 20 mm stone aggrigate in coping or chamfered on edges complete all as specified.

Supply and fix in repair hot moulded FRP looping /Junction box size 280 mmx200 mm for street light poles with locking arrangement and suitable connection for three phase incomming cable 3 phase out going cable and single phase connection for light fitting incl controlled MCB SP-10 Amps -01 Nos enclosed in thermo plastic in closed shock proof safe IP-65, weather,vermin proof,dust and water proof complete with two nos cables entry incl gland of standard size with suitable size mild steel clamps to fixed on pole complete all as specified. Make-Neptune/Hensel/Sintex

M&L for PCC preparation including cutting up to 45 cm width and depth of the road/hard standing and making good disturbed surfaces by using PCC type C2(1:3:6) by using 40mm graded stone aggregate for the fixing the pipe/laying cables complete all as specified.

M&L for 50mm dia steel tubes (light grade) galvanised with fittings, laid in trenches/wall for protection of underground earth strip when crossing the road/fixing on wall as in repair complete all as specified and directed.

Excavation in trenches any type of soil , n exc 1.5m wide and n exc 1.5m in depth , for foundation , etc or for shaft, well, cesspits , manholes , pier hole etc n exc 1.5 m in depth and getting out for laying of cable complete all as specificed and directed.

Returning , filling in including, spreading , levelling , watering and well reamming in layers not exc. 25 cm within the 1 mtr strech complete all as specificed and directed.

Removing excavated material n exc 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specificed and directed.

M & L for sand cushioning with dry coarse sand to under ground cable 23 cm thick, 8 cm thick below the cable and 15 cm thick after laying the cable complete all as specified and directed by Engineer-in-Charge. Note : Thickness after punning shall be considered for payment.

Boring of holes under road, pavement, hard standing by trenchless technology usingn ultra sound technique and necessary machine including HDPE/GI pipe of 100 mm dia suitable for 0.4 mpa working pressure

M&L for bricks of sub class ‘B’ bricks, for cable protection in trenches laid dry and flat.

M&L for Earthing for Pole /DB complete with galvanized steel plate electrode of size 600x600x6.3mm thick buried directly in ground with earth pit not less than 2.25 meter deep below ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanized iron earth strip of size 4mm dia earth lead by means of nuts, bolts, check nuts, washers of galvanised iron as steel, protected by galvanized iron pipe 40mm bore (Medium grade) all as directed including cement concrete (1:3:6) type C-1 earth pit with precast RCC (1:1.5:3) type A-1 cover slab of size 42 x 42 x10cm thick reinforced with 8mm dia TMT bars @ 15 cm c/c both ways with 10mm dia mild steel round bar of 30 cm long, bent to shape as lifting handle, funnel, wire mesh, 20 mm bore galvanized iron pipe (medium grade) for watering, charcoal or coke and salt in alternate layers with necessary earth work in soft/loose soil complete all as shown in electrical plate No 3 of SSR Part I including testing on completion all complete as specified and directed.

M&L for 75 mm dia HDPE pipes PN 10 with fittings, laid in trenches/wall for protection of underground cable when crossing the road/fixing on wall.

M&L for 50 mm dia HDPE pipes PN 10 with fittings, laid in trenches/wall for protection of underground cable when crossing the road/fixing on wall.

Supply and fix LED type street light fitting 60 watt pressure dia cast aluminum housing LED street light luminaries with IP 66 including GI pipe medium grade with suitable size bracket bend in 120 degree and clamps,nuts,bolts etc with all accessories complete all as specified and as directed. Make Havells ENDURA SUNDOWN Cat Pt No ENDURASUNDOWNSL60WLWLED765PASYBOTG and equivalent Make Philips/CG

M&L for fabrication of cross arms bracings supports,clamps and back plates,iron stainer, water gate, ladder for clear water tank etc as required structural steel section including nuts, bolts, washers, welding,bending, cold or hot, drilling holes for bolts in any shape or size and including of one coat of primer and one under coat and one finishing coat of paint complete all as specified and as directed by Engr in charge.

M&L for street light bracket made to shape from 40mm dia length 1.5m GI Pipe medium grade incl two number of clamps made from 50 x 6 Flat iron nut bolts complete all as directed

RM INFRASTRUCTURE

Singla Electricals

M/S Sonu Traders

UNITED ENGINEERING CORPORATION

SRI SAI CONSTRUCTION COMPANY

P.K ENTERPRISES

M/s GURFATEH BUILDERS