Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹25.3 LAccepted-AOC | L1 | Accepted-AOC Lowest bidder | |
| 2 | L2₹27.0 L+₹1.2 L (4.79%)Rejected-Finance RANGAPAHAR RAILWAY CROSSING GATE NO 1 DIMAPUR 797112 NAGALAND | DIMAPUR | NAGALAND | 797112 | L2 | Rejected-Finance Other than lowest | |
| 3 | L3₹29.0 L+₹3.2 L (12.4%)Rejected-Finance | L3 | Rejected-Finance Other than lowest | |
| 4 | L4₹30.3 L+₹4.5 L (17.5%)Rejected-Finance | L4 | Rejected-Finance Other than lowest | |
| 5 | Rejected-Technical | - | Rejected-Technical Not eligible |
| Sl No | Description | Qty | Unit | MAURYA CONSTRUCTIONS L2 | M/s Ritz Marketing L4 | M/S N JADUMANI SINGH L1 | M/S MANGANG RENOVATIONS L3 |
|---|---|---|---|---|---|---|---|
| 1.00Schedule 'A' | |||||||
| 1.01 | Material and labour for conducting ‘B’ check of DG Set 500 KVA capacity Make: Kirloskar at 183 MH DG sets of above capacity installed at 183 MH to carry out maintenance / servicing as given below all as directed:-
(i) Change of diesel filter/oil filter/Air filter/top up/replacement of engine oil, coolant if required.
(ii) Check and clean engine, alternator battery,instrument panel, elect panel, Timer, Contactors ,Meters and others etc.
(iii) Tightening of all nuts & bolts of DG set and its accessories.
(iv) Check for any diesel lekage from any point and rectify if observed.
(v) Check and adjust fan belt tension, replace the fan belts if found damaged.
(vi) Check leakage of smoke from exhaust system/silencer,Repair if required.
(vii) Check electrical connections of engine .The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order
(viii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged.AVM to be provided by contractor.
(ix) Check exhaust pipe, flange and lagging Repair if found damaged.
(x) Check output of alternator ,if found OK adjust the same to specified values in case of brush type.
(xi) Checking of all hoses and cleanup,change/tighten if required. (xii) Checking of all hoses and cleanup if required. Also changing air filter elements,if required. (xiii) Oiling,Greasing and checking for proper & smooth functioning. etc and refitting, testing on load complete (Note :- Spares parts/ Engine oil/coolant /distilled water etc. will be measured and paid separately .) | 1 | Each Job | 23,800 ₹23,800 | 24,850 ₹24,850 | 22,850 ₹22,850 Lowest | 24,300 ₹24,300 |
| 2.00 | Material and labour for conducting ‘B’ check of DG Set 160 KVA capacity Make: Kirloskar at High Lift Pump House DG sets of above capacity installed at above location to carry out maintenance / servicing as given below all as directed:-
(i) Change of diesel filter/oil filter/Air filter/top up/replacement of engine oil, coolant if required.
(ii) Check and clean engine, alternator battery,instrument panel, elect panel, Timer, Contactors ,Meters and others etc.
(iii) Tightening of all nuts & bolts of DG set and its accessories.
(iv) Check for any diesel lekage from any point and rectify if observed.
(v) Check and adjust fan belt tension, replace the fan belts if found damaged.
(vi) Check leakage of smoke from exhaust system/silencer,Repair if required.
(vii) Check electrical connections of engine .The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order
(viii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged.AVM to be provided by contractor.
(ix) Check exhaust pipe, flange and lagging Repair if found damaged.
(x) Check output of alternator ,if found OK adjust the same to specified values in case of brush type.
(xi) Checking of all hoses and cleanup,change/tighten if required. (xii) Checking of all hoses and cleanup if required. Also changing air filter elements,if required. (xiii) Oiling,Greasing and checking for proper & smooth functioning. etc and refitting, testing on load complete (Note :- Spares parts/ Engine oil/coolant /distilled water etc. will be measured and paid separately .) | 1 | Each Job | 16,250 ₹16,250 | 17,600 ₹17,600 | 16,050 ₹16,050 Lowest | 17,000 ₹17,000 |
| 3.00 | Material and labour for conducting ‘B’ check of DG Set 100 KVA capacity Make: Kirloskar at 183 MH & 57 MDSR, DG sets of above capacity installed at above location to carry out maintenance / servicing as given below all as directed:-
(i) Change of diesel filter/oil filter/Air filter/top up/replacement of engine oil, coolant if required.
(ii) Check and clean engine, alternator battery,instrument panel, elect panel, Timer, Contactors ,Meters and others etc.
(iii) Tightening of all nuts & bolts of DG set and its accessories.
(iv) Check for any diesel lekage from any point and rectify if observed.
(v) Check and adjust fan belt tension, replace the fan belts if found damaged.
(vi) Check leakage of smoke from exhaust system/silencer,Repair if required.
(vii) Check electrical connections of engine .The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order
(viii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged.AVM to be provided by contractor.
(ix) Check exhaust pipe, flange and lagging Repair if found damaged.
(x) Check output of alternator ,if found OK adjust the same to specified values in case of brush type.
(xi) Checking of all hoses and cleanup,change/tighten if required. (xii) Checking of all hoses and cleanup if required. Also changing air filter elements,if required. (xiii) Oiling,Greasing and checking for proper & smooth functioning. etc and refitting, testing on load complete (Note :- Spares parts/ Engine oil/coolant /distilled water etc. will be measured and paid separately .) | 2 | Each Job | 13,650 ₹27,300 | 14,150 ₹28,300 | 13,050 ₹26,100 Lowest | 13,650 ₹27,300 |
| 4.00 | Material and labour for conducting ‘B’ check of DG Set 62.5 KVA capacity Make: Kirloskar at 183 MH & KLP Pump House, DG sets of above capacity installed at above location to carry out maintenance / servicing as given below all as directed:-
(i) Change of diesel filter/oil filter/Air filter/top up/replacement of engine oil, coolant if required.
(ii) Check and clean engine, alternator battery,instrument panel, elect panel, Timer, Contactors ,Meters and others etc.
(iii) Tightening of all nuts & bolts of DG set and its accessories.
(iv) Check for any diesel lekage from any point and rectify if observed.
(v) Check and adjust fan belt tension, replace the fan belts if found damaged.
(vi) Check leakage of smoke from exhaust system/silencer,Repair if required.
(vii) Check electrical connections of engine .The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order
(viii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged.AVM to be provided by contractor.
(ix) Check exhaust pipe, flange and lagging Repair if found damaged.
(x) Check output of alternator ,if found OK adjust the same to specified values in case of brush type.
(xi) Checking of all hoses and cleanup,change/tighten if required. (xii) Checking of all hoses and cleanup if required. Also changing air filter elements,if required. (xiii) Oiling,Greasing and checking for proper & smooth functioning. etc and refitting, testing on load complete (Note :- Spares parts/ Engine oil/coolant /distilled water etc. will be measured and paid separately .) | 2 | Each Job | 12,300 ₹24,600 | 1,325 ₹2,650 Lowest | 11,950 ₹23,900 | 12,700 ₹25,400 |
| 5.00 | Material and labour for conducting ‘B’ check of DG Set 30 KVA to 45 KVA capacity Make: Kirloskar at 27 R&O Flt & E/M complaint Cell, DG sets of above capacity installed at above location to carry out maintenance / servicing as given below all as directed:-
(i) Change of diesel filter/oil filter/Air filter/top up/replacement of engine oil, coolant if required.
(ii) Check and clean engine, alternator battery,instrument panel, elect panel, Timer, Contactors ,Meters and others etc.
(iii) Tightening of all nuts & bolts of DG set and its accessories.
(iv) Check for any diesel lekage from any point and rectify if observed.
(v) Check and adjust fan belt tension, replace the fan belts if found damaged.
(vi) Check leakage of smoke from exhaust system/silencer,Repair if required.
(vii) Check electrical connections of engine .The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order
(viii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged.AVM to be provided by contractor.
(ix) Check exhaust pipe, flange and lagging Repair if found damaged.
(x) Check output of alternator ,if found OK adjust the same to specified values in case of brush type.
(xi) Checking of all hoses and cleanup,change/tighten if required. (xii) Checking of all hoses and cleanup if required. Also changing air filter elements,if required. (xiii) Oiling,Greasing and checking for proper & smooth functioning. etc and refitting, testing on load complete (Note :- Spares parts/ Engine oil/coolant /distilled water etc. will be measured and paid separately .) | 2 | Each Job | 11,800 ₹23,600 | 12,500 ₹25,000 | 11,700 ₹23,400 Lowest | 12,000 ₹24,000 |
| 6.00 | Supply only the following spare parts/items for DG set capacity 500 KVA complete as specified and as ditected. (Make : Kirloskar) (Note: Make of spares parts shall be of the same original manufacturer as per existing) :- (6.01) Diesel fuel filter assembly (Pre filter & Micro filter) (Set of 02 Nos) | 1 | Each set | 4,812 ₹4,812 | 5,720 ₹5,720 | 4,789 ₹4,789 Lowest | 5,000 ₹5,000 |
| 7.00 | (6.02) Air filter assembly | 1 | Each set | 4,295 ₹4,295 | 4,555 ₹4,555 | 4,198 ₹4,198 Lowest | 4,300 ₹4,300 |
| 8.00 | (6.03) V' belt as per existing make/model | 1 | Each | 1,260 ₹1,260 | 1,425 ₹1,425 | 1,258 ₹1,258 Lowest | 1,350 ₹1,350 |
| 9.00 | (6.04) Fuel pipe | 1 | Each | 2,200 ₹2,200 Lowest | 2,675 ₹2,675 | 2,200 ₹2,200 Lowest | 2,200 ₹2,200 Lowest |
Tender Value
₹25 L
EMD Value
₹50,000
Closing Date
21 Jul 2025, 6:00 pmClosed
GE 869 EWS
GE 869 EWS PIN 913869 C/O 99APO
REPAIR/MAINT OF DG SET, AMF PANELS, LT PANELS, AND ALLED WKS AT LMS
2025_MES_703151_2
8657/E8
Open Tender
Civil Works
Item Rate
210 days
LEIMAKHONG MIL STN
AS PER TENDER DOCUMENTS
2 documents required · 2 mandatory
₹500
GE 869 EWS
₹50,000
Yes
11 Sept 2025
12 Jun 2025
28 Jul 2025
12 Jun 2025
21 Jul 2025
6 Jul 2025
Amount
Schedule 'A'
Material and labour for conducting ‘B’ check of DG Set 500 KVA capacity Make: Kirloskar at 183 MH DG sets of above capacity installed at 183 MH to carry out maintenance / servicing as given below all as directed:- (i) Change of diesel filter/oil filter/Air filter/top up/replacement of engine oil, coolant if required. (ii) Check and clean engine, alternator battery,instrument panel, elect panel, Timer, Contactors ,Meters and others etc. (iii) Tightening of all nuts & bolts of DG set and its accessories. (iv) Check for any diesel lekage from any point and rectify if observed. (v) Check and adjust fan belt tension, replace the fan belts if found damaged. (vi) Check leakage of smoke from exhaust system/silencer,Repair if required. (vii) Check electrical connections of engine .The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order (viii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged.AVM to be provided by contractor. (ix) Check exhaust pipe, flange and lagging Repair if found damaged. (x) Check output of alternator ,if found OK adjust the same to specified values in case of brush type. (xi) Checking of all hoses and cleanup,change/tighten if required. (xii) Checking of all hoses and cleanup if required. Also changing air filter elements,if required. (xiii) Oiling,Greasing and checking for proper & smooth functioning. etc and refitting, testing on load complete (Note :- Spares parts/ Engine oil/coolant /distilled water etc. will be measured and paid separately .)
Material and labour for conducting ‘B’ check of DG Set 160 KVA capacity Make: Kirloskar at High Lift Pump House DG sets of above capacity installed at above location to carry out maintenance / servicing as given below all as directed:- (i) Change of diesel filter/oil filter/Air filter/top up/replacement of engine oil, coolant if required. (ii) Check and clean engine, alternator battery,instrument panel, elect panel, Timer, Contactors ,Meters and others etc. (iii) Tightening of all nuts & bolts of DG set and its accessories. (iv) Check for any diesel lekage from any point and rectify if observed. (v) Check and adjust fan belt tension, replace the fan belts if found damaged. (vi) Check leakage of smoke from exhaust system/silencer,Repair if required. (vii) Check electrical connections of engine .The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order (viii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged.AVM to be provided by contractor. (ix) Check exhaust pipe, flange and lagging Repair if found damaged. (x) Check output of alternator ,if found OK adjust the same to specified values in case of brush type. (xi) Checking of all hoses and cleanup,change/tighten if required. (xii) Checking of all hoses and cleanup if required. Also changing air filter elements,if required. (xiii) Oiling,Greasing and checking for proper & smooth functioning. etc and refitting, testing on load complete (Note :- Spares parts/ Engine oil/coolant /distilled water etc. will be measured and paid separately .)
Material and labour for conducting ‘B’ check of DG Set 100 KVA capacity Make: Kirloskar at 183 MH & 57 MDSR, DG sets of above capacity installed at above location to carry out maintenance / servicing as given below all as directed:- (i) Change of diesel filter/oil filter/Air filter/top up/replacement of engine oil, coolant if required. (ii) Check and clean engine, alternator battery,instrument panel, elect panel, Timer, Contactors ,Meters and others etc. (iii) Tightening of all nuts & bolts of DG set and its accessories. (iv) Check for any diesel lekage from any point and rectify if observed. (v) Check and adjust fan belt tension, replace the fan belts if found damaged. (vi) Check leakage of smoke from exhaust system/silencer,Repair if required. (vii) Check electrical connections of engine .The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order (viii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged.AVM to be provided by contractor. (ix) Check exhaust pipe, flange and lagging Repair if found damaged. (x) Check output of alternator ,if found OK adjust the same to specified values in case of brush type. (xi) Checking of all hoses and cleanup,change/tighten if required. (xii) Checking of all hoses and cleanup if required. Also changing air filter elements,if required. (xiii) Oiling,Greasing and checking for proper & smooth functioning. etc and refitting, testing on load complete (Note :- Spares parts/ Engine oil/coolant /distilled water etc. will be measured and paid separately .)
Material and labour for conducting ‘B’ check of DG Set 62.5 KVA capacity Make: Kirloskar at 183 MH & KLP Pump House, DG sets of above capacity installed at above location to carry out maintenance / servicing as given below all as directed:- (i) Change of diesel filter/oil filter/Air filter/top up/replacement of engine oil, coolant if required. (ii) Check and clean engine, alternator battery,instrument panel, elect panel, Timer, Contactors ,Meters and others etc. (iii) Tightening of all nuts & bolts of DG set and its accessories. (iv) Check for any diesel lekage from any point and rectify if observed. (v) Check and adjust fan belt tension, replace the fan belts if found damaged. (vi) Check leakage of smoke from exhaust system/silencer,Repair if required. (vii) Check electrical connections of engine .The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order (viii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged.AVM to be provided by contractor. (ix) Check exhaust pipe, flange and lagging Repair if found damaged. (x) Check output of alternator ,if found OK adjust the same to specified values in case of brush type. (xi) Checking of all hoses and cleanup,change/tighten if required. (xii) Checking of all hoses and cleanup if required. Also changing air filter elements,if required. (xiii) Oiling,Greasing and checking for proper & smooth functioning. etc and refitting, testing on load complete (Note :- Spares parts/ Engine oil/coolant /distilled water etc. will be measured and paid separately .)
Material and labour for conducting ‘B’ check of DG Set 30 KVA to 45 KVA capacity Make: Kirloskar at 27 R&O Flt & E/M complaint Cell, DG sets of above capacity installed at above location to carry out maintenance / servicing as given below all as directed:- (i) Change of diesel filter/oil filter/Air filter/top up/replacement of engine oil, coolant if required. (ii) Check and clean engine, alternator battery,instrument panel, elect panel, Timer, Contactors ,Meters and others etc. (iii) Tightening of all nuts & bolts of DG set and its accessories. (iv) Check for any diesel lekage from any point and rectify if observed. (v) Check and adjust fan belt tension, replace the fan belts if found damaged. (vi) Check leakage of smoke from exhaust system/silencer,Repair if required. (vii) Check electrical connections of engine .The wiring shall be maintened properly and engine starting system from engine instrument panel is to be kept in order (viii) Check and tighten the AVM pads nuts and bolts, change AVM pads if found damaged.AVM to be provided by contractor. (ix) Check exhaust pipe, flange and lagging Repair if found damaged. (x) Check output of alternator ,if found OK adjust the same to specified values in case of brush type. (xi) Checking of all hoses and cleanup,change/tighten if required. (xii) Checking of all hoses and cleanup if required. Also changing air filter elements,if required. (xiii) Oiling,Greasing and checking for proper & smooth functioning. etc and refitting, testing on load complete (Note :- Spares parts/ Engine oil/coolant /distilled water etc. will be measured and paid separately .)
Supply only the following spare parts/items for DG set capacity 500 KVA complete as specified and as ditected. (Make : Kirloskar) (Note: Make of spares parts shall be of the same original manufacturer as per existing) :- (6.01) Diesel fuel filter assembly (Pre filter & Micro filter) (Set of 02 Nos)
(6.02) Air filter assembly
(6.03) V' belt as per existing make/model
(6.04) Fuel pipe
(6.05) Radiator hose pipe with clamps for top and bottom
(6.06) Battery terminal leads copper with lugs
(6.07) Oil filter assembly
Supply only the following spare parts/items for DG set capacity 160 KVA complete as specified and as ditected. (Make : Kirloskar) (Note: Make of spares parts shall be of the same original manufacturer as per existing) :- (13.01) Diesel fuel filters assembly (Pre filter & Micro filter) (Set of 02 Nos)
(13.02) Air filter assembly
(13.03) V' belt as per existing make/model
(13.04) Fuel pipe
(13.05) Radiator hose pipe with clamps for top and bottom
(13.06) Battery terminal leads copper with lugs
(13.07) Oil filter assembly
(13.08) Self Starter assembly including complete accessories of ISI Marked
(13.09) Carbon brush as per existing make and model.
(13.10) High pressure oil pipe as per existing make and model.
Taking down & opening of cylinder head of 100KVA DG Set and replacement of new piston ring, inlet valves, exhaust valves, oil seal, cylinder gasket, replacement of Engine Oil and reassembling the same in its original position and testing complete all as specified and directed.
Supply only the following spare parts/items for DG set capacity 100 KVA complete as specified and as ditected. (Make : Kirloskar) (Note: Make of spares parts shall be of the same original manufacturer as per existing) :- (24.01) Diesel fuel filters assembly (Pre filter & Micro filter) (Set of 02 Nos)
(24.02) Air filter assembly
(24.03) V' belt as per existing make/model
(24.04) Fuel pipe
(24.05) Radiator hose pipe with clamps for top and bottom
(24.06) Battery terminal leads copper with lugs
(24.07) Oil filter assembly
(24.08) Inlet & Exhaust valve set of 06 Nos
(24.09) Packing kit
(24.10) Push rod set
(24.11) Oil pressure gauge
(24.12) Flange with Rubber coupling
(24.13) Set Nozzle
(24.14) Oil seal set
(24.15) Piston assembly with piston ring set
(24.16) Oil pump assembly
(24.17) Cylinder liner with JT ring
(24.18) Valve Guide assembly
(24.19) Valve seat assembly inlet
(24.20) Valve seat assembly exhaust
(24.21) Gasket set complete
(24.22) Set of various sizes nut bolt, washers for joints
(24.23) LLOP sensor as per existing make/model
Supply only the following spare parts/items for DG set capacity 62.5 KVA complete as specified and as ditected. (Make : Kirloskar) (Note: Make of spares parts shall be of the same original manufacturer as per existing) :- (47.01) Diesel fuel filters assembly (Pre filter & Micro filter) (Set of 02 Nos)
(47.02) Air filter assembly
(47.03) V' belt as per existing make/model
(47.04) Fuel pipe
(47.05) Radiator hose pipe with clamps for top and bottom
(47.06) Battery terminal leads copper with lugs
(47.07) Oil filter assembly
(47.08) Turbo filter assembly
(47.09) Engine start relay 12/24 Volts compitable with existing AMF panel complete all as specified.
(47.10) Over and under voltage relay 3 phase 415 Volts compitable with existing AMF panel complete all as specified.
(47.11) Auxiliary relay 8 pin /11 pin compitable with existing AMF panel complete all as specified.
(47.12) Timer switch AC/DC compitable with existing AMF panel complete all as specified.
(47.13) High pressure oil pipe as per existing make and model.
Supply only the following spare parts/items for DG set capacity 45 KVA complete as specified and as ditected. (Make : Kirloskar) (Note: Make of spares parts shall be of the same original manufacturer as per existing) :- (60.01) Diesel fuel filters assembly (Pre filter & Micro filter) (Set of 02 Nos)
(60.02) Air filter assembly
(60.03) V' belt as per existing make/model
(60.04) Fuel pipe
(60.05) Radiator hose pipe with clamps for top and bottom
(60.06) Battery terminal leads copper with lugs
(61.07) Self Starter assembly including complete accessories of ISI Marked
(60.08) Ignition switch
(60.09) Oil filter assembly
(60.10) Carbon brush as per existing make and model.
(60.11) High pressure oil pipe as per existing make and model.
Supply only the following spare parts/items for DG set capacity 30 KVA complete as specified and as ditected. (Make : Kirloskar) (Note: Make of spares parts shall be of the same original manufacturer as per existing) :- (71.01) Diesel fuel filters assembly (Pre filter & Micro filter) (Set of 02 Nos)
(71.02) Air filter assembly
(71.03) V' belt as per existing make/model
(71.04) Fuel pipe
(71.05) Radiator hose pipe with clamps for top and bottom
(71.06) Battery terminal leads copper with lugs
(71.07) Oil filter assembly
(71.08) Ignition switch
(71.09) Self Starter assembly including complete accessories of ISI Marked
(71.10) LLOP sensor as per existing make and model
(71.11) Carbon brush as per existing make and model.
(71.12) High pressure oil pipe as per existing make and model.
M&L in replacement of old engine oil from the sump of DG Sets installed at various locations after cleaning the oil sump throughly supply & filling new Lub oil, SAE 15W40 grade complete all as specified and directed by Engineer-In-Charge.
Supply and filling radiator coolant in 5 ltrs sealed pack for DG sets installed at various locations complete all as specified and directed.
M & L for dismantaling of FIP for ovarhaulling and caliberation in authorised workshop including replacement of wornout rings plungers, damper plate, gaskit etc and reassembling testing complete for DG sets of capacity 30 KVA to 45 KVA complete all as specified and directed.
M & L for dismantaling of FIP for ovarhaulling and caliberation in authorised workshop including replacement of wornout rings plungers, damper plate, gaskit etc and reassembling testing complete for DG sets of capacity 62.5 KVA to 100 KVA complete all as specified and directed.
M&L for repair overhalling of self starter including replacement of worn out clutch assembly bush, plunger assembly, solenoid switch, corbon brushs, spring, ball bearing etc for DG sets of capacity 30 KVA to 45 KVA complete all as specified & directed. (Note :- Spares parts like clutch assembly, solenoid assembly, planetary gear assembly, bendix drive, copper winding of motor will be measured and paid separately.)
Supply only bendix drive pinon assembly of self starter of capacity 30 KVA to 45 KVA DG set
Supply only cluch assembly of self starter of capacity 30 KVA to 45 KVA DG set
Supply only solenoid assembly of self starter of capacity 30 KVA to 45 KVA DG set
Supply only planetary Gear assembly of self starter of capacity 30 KVA to 45 KVA DG set
Supply only Bearing of starter of capacity 30 KVA to 45 KVA DG set
Supply only Bush of starter of capacity 30 KVA to 45 KVA DG set
M&L for repair overhalling of self starter including replacement of worn out clutch assembly bush, plunger assembly, solenoid switch, corbon brushs, spring, ball bearing etc for DG sets of capacity 62.5 KVA to 100 KVA complete all as specified & directed. (Note :- Spares parts like clutch assembly, solenoid assembly, planetary gear assembly, bendix drive, copper winding of motor will be measured and paid separately.)
Supply only bendix drive pinon assembly of self starter of capacity 62.5 KVA to 100 KVA DG set
Supply only cluch assembly of self starter of capacity 62.5 KVA to 100 KVA DG set
Supply only solenoid assembly of self starter of capacity 62.5 KVA to 100 KVA DG set
Supply only planetary gear assembly of self starter of capacity 62.5 KVA to 100 KVA DG set
Supply only Bearing of starter of capacity 62.5 KVA to 100 KVA DG set
Supply only Bush of starter of capacity 62.5 KVA to 100 KVA DG set
M&L for repair overhalling of self starter including replacement of worn out clutch assembly bush, plunger assembly, solenoid switch, corbon brushs, spring, ball bearing etc for DG sets of capacity 160 KVA complete all as specified & directed. (Note :- Spares parts like clutch assembly, solenoid assembly, planetary gear assembly, bendix drive, copper winding of motor will be measured and paid separately.)
Supply only bendix drive pinon assembly of self starter of capacity 160 KVA DG set
Supply only cluch assembly of self starter of capacity 160 KVA DG set
Supply only solenoid assembly of self starter of capacity 160 KVA DG set
Supply only planetary gear assembly of self starter of capacity capacity 160 KVA DG set
Supply only Bearing of starter of capacity capacity 160 KVA DG set
Supply only Bush of starter of capacity capacity 160 KVA DG set
M&L in repair of rewinding of self starter motor of DG Set 30 KVA to 160 KVA, strip opening and removal of burnt winding wire, rewinding the motor with suitable size of heavy grade (ISI mark ) copper winding wire, duly providing leathoride sheets, cotton tape, insulation sleeves, varnish, etc 6 month waranty period shall given by the dealer/contractor after repair including testing complete all as specified and directed.
M&L for Repair/ overhauling of dynamo/charging alternator including replacement carbon, brushes holder, spring commutator/slipring assembly bearing regulator its of any make, type for 500 KVA capacity, complete all as directed. (Note: The quoted rate per unit shall deemed to be inclusive of repair/ replacement of carbon brushes, holder, spring commulator, ball bearing etc.)
M&L for Repair/overhaling of dynamo/charging alternator including replacement carbon, brushes holder, spring commutator/slipring assembly bearing regulator its of any make, type 30 KVA to 160 KVA capacity, complete all as directed. (Note: The quoted rate per unit shall deemed to be inclusive of repair/ replacement of carbon brushes, holder, spring commulator, ball bearing etc.)
M&L for cleaning of the fuel tank of DG sets of of capacity 500 KVA after decaning the diesel, after throughly cleaning with kerosene oil including replacement of level indicator pipe complete all as directed by EIC.
M&L for cleaning of the fuel tank of DG sets of of capacity 160 KVA after decaning the diesel, after throughly cleaning with kerosene oil including replacement of level indicator pipe complete all as directed by EIC.
M&L for cleaning of the fuel tank of DG sets of of capacity 100 KVA after decaning the diesel, after throughly cleaning with kerosene oil including replacement of level indicator pipe complete all as directed by EIC.
M&L for cleaning of the fuel tank of DG sets of of capacity 62.5 KVA after decaning the diesel, after throughly cleaning with kerosene oil including replacement of level indicator pipe complete all as directed by EIC.
M&L for cleaning of the fuel tank of DG sets of of capacity 30 KVA to 45 KVA after decaning the diesel, after throughly cleaning with kerosene oil including replacement of level indicator pipe complete all as directed by EIC.
M&L for dismantling and removing of water pump assembly complete from the engine repair/overhaulling the same by replacing worn components like bearing, impeller, bushes, oil seal, water seal, gaskit etc. reassembling, refixing and testing complete for DG sets of capacity 500 KVA complete all as specified & directed. (Note: The quoted rate per unit shall deemed to be inclusive of repair/ replacement of bearing, oil seal, water seal, gasket etc etc.)
M&L for dismantling and removing of water pump assessmbly complete from the engine repair/overhaulling the same by replacing worn components like bearing, impeller, bushes, oil seal, water seal, gaskit etc. reassembling, refixing and testing complete for DG sets of capacity 100 KVA to 160 KVA complete all as specified & directed. (Note: The quoted rate per unit shall deemed to be inclusive of repair/ replacement of bearing, oil seal, water seal, gasket etc etc.)
M&L for dismantling and removing of water pump assessmbly complete from the engine repair/overhaulling the same by replacing worn components like bearing, impeller, bushes, oil seal, water seal, gasket etc. reassembling, refixing and testing complete for DG sets of capacity 30 KVA to 62.5 KVA complete all as specified & directed. (Note: The quoted rate per unit shall deemed to be inclusive of repair/ replacement of bearing, oil seal, water seal, gasket etc etc.)
M & L for Automatic voltage regulator suitable for DG set of capacity 500 KVA as per existing Make & model and as directed by EIC.
M & L for Automatic voltage regulator suitable for DG set of capacity 45 KVA to 160 KVA as per existing Make & model and as directed by EIC.
M & L for replacement of fuel shutdown/solonoid valve assembly complete testing including replacement of old unsv valves of any capacity DG set, complete all as directed by EIC .
M & L for replacement of existing make and model fly wheel ring including heating for press fitting for engine of DG sets of capacity 100 KVA to 160 KVA complete all as specified & directed.
M & L for replacement of existing make and model fly wheel ring including heating for press fitting for engine of DG sets of capacity 30 KVA to 62.5 KVA complete all as specified & directed.
M & L for Dismantling of radiator of DG set of capacity 100 KVA to 160 KVA and transporting to work shop for servicing/cleaning after dismantling twin tanks, replacement of gasket packing, nuts, bolts, washers, descaling with appropriate chemical and welding of copper brazing of damaged fins/tubes and reassembling & refixing in same position after testing complete all as specified & directed.
M & L for Dismantling of radiator of DG set of capacity 30 KVA to 62.5 KVA and transporting to work shop for servicing/cleaning after dismantling twin tanks, replacement of gasket packing, nuts, bolts, washers, descaling with appropriate chemical and welding of copper brazing of damazed fins/tubes and reassembling & refixing in same position after testing complete all as specified & directed.
M&L for scraping the peeled oil Paint on 100 to 160 KVA DG set including alternator,Engine and Fuel tank, Preparing the surfaces, cleaning the dust, dirt and applying two coats of synthetic enamel paint of approved shade and writing SM No on the DG set and all as directed by Engineer-In-charge.
M&L for scraping the peeled oil Paint on 30 KVA to 62.5 KVA DG set including alternator,Engine and Fuel tank, Preparing the surfaces, cleaning the dust, dirt and applying two coats of synthetic enamel paint of approved shade and writing SM No on the DG set and all as directed by Engineer-In-charge.
M & L for repairing/replacing of complete GENSET engine wiring of 30 KVA to 160 KVA capacity with all accessories including extension of existing PVC insulated , stranderd copper conductor wire of suitable size for control/ signal circuit complete with & including flexible conduit, copper lugs, PVC ties, fasteners & synchronisation and calliberation of AMF panel with engine control panel complete all as specified & directed.
Supply and fix in replacement with Micro-processor based generator set monitoring and control system including an intuitive operator interface that allows for complete generator set control as well as system metering, fault annunciation, configuration and diagnostics, LED backlit LCD display with tactile feel soft-switches & generator set status LED lamps, remote START-STOP suitable for DG set of capacity 160 KVA of existing make and existing model including taking out old one complete all as specified and directed by Engr-in-Charge
Supply and fix in replacement with Micro-processor based generator set monitoring and control system including an intuitive operator interface that allows for complete generator set control as well as system metering, fault annunciation, configuration and diagnostics, LED backlit LCD display with tactile feel soft-switches & generator set status LED lamps, remote START-STOP suitable for DG set of capacity 100 KVA of existing make and existing model including taking out old one complete all as specified and directed by Engr-in-Charge
Supply and fix in replacement with Micro-processor based generator set monitoring and control system including an intuitive operator interface that allows for complete generator set control as well as system metering, fault annunciation, configuration and diagnostics, LED backlit LCD display with tactile feel soft-switches & generator set status LED lamps, remote START-STOP suitable for DG set of capacity 30 KVA of existing make and existing model including taking out old one complete all as specified and directed by Engr-in-Charge
M&L for replacement of SMPS based Electronic Battery Charger suitable for 12 / 24 Volts battery charging system complete all as specified & directed.
S&F in replacement with new Exhaust silencer suitable for DG Set of 45 KVA to 100 KVA capacities all as specified and directed by Engineer-In-Charge.
M&L for replacement of On Load change over switch 4 Pole, 415 Volt, in sheet steel enclosure of capacity 125 Amps complete all as specified & directed.
M&L for replacement of On Load change over switch 4 Pole, 415 Volt, in sheet steel enclosure of capacity 200 Amps complete all as specified & directed.
M&L for replacement of On Load change over switch 4 Pole, 415 Volt, in existing panel of capacity 200 Amps complete all as specified & directed.
M&L for filling / pouring distilled water packed in 20 / 25/ 35 litre PVC containers & top up of electrolite for servicing of battery complete all as specified & directed .
Supply and installation of maintenance free battery lead acid type of capacity 12 Volt 180 AH for DG Sets installed at various locations Complete all as specified & directed by Engineer-in-charge. (Make Exide express/ Amaron/ Microtek)
Supply, laying, Jointing and testing in replacement of LT UG cable XLPE insulated,PVC bedded galvanised steel strip or wire armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 120 sqmm 3.5 core laid in trenches / on poles / walls / in ducts / passing through pipes and including necessary cable lugs, bolts, nuts and washers complete all as specified and directed. Note : Excavation, earthwork and cable protection shall be measured and paid separately under relevant items of Sch 'A'.
All as per serial item No. 141 above but for 95 Sqmm 3.5 Core.
All as per serial item No. 141 above but for 70 Sqmm 3.5 Core.
All as per serial item No. 141 above but for 50 Sqmm 3.5 Core.
All as per serial item No. 141 above but for 35 Sqmm 3.5 Core.
All as per serial item No. 141 above but for 25 Sqmm 4 Core.
All as per serial item No. 141 above but for 16 Sqmm 4 Core.
All as per serial item No. 141 above but for 10 Sqmm 2 Core.
S&F in replacement of aluminium cable lugs for cable size 10 Sqmm to 25 Sqmm complete all as specified and directed.
S&F in replacement of aluminium cable lugs for cable size 35 Sqmm to 70 Sqmm complete all as specified and directed.
S&F in replacement of aluminium cable lugs for cable size 95 Sqmm to 120 Sqmm complete all as specified and directed.
Excavation in trenches not exc 1.5 mtr wide and not exc1.5 mtr in depth for laying of cables etc. in any type of soil and getting out complete all as specified and directed
Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm as in soils complete all as specified and as directed.
Removing excavated materials to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 mtr above the starting point as in soils complete all as specified and as directed.
Supply and spread sand in trenches as sand cushioning to underground cable for protection with dry fine river sand and provide required cover after punning down 18CM will be measured and paid complete all as specified and directed. (Note: Thickness of sand cushion after punning down will be measured and paid.)
Supply and laying well burnt sub class ‘B’ bricks ( designated 75) locally available best quality, laid dry in trenches for protection of underground cablecomplete all as specified and directed.
Supply and laying in repair of 50 mm bore GI tube light grade as in cable protection pipe including all fittings complete all as specified and directed.
M&L for taking out existing Panel and shifting of LT panel of any size with all accessories and fixing it to other location as directed by Engr-in-Charge at site, connecting cable connection with connecting accessories, incl foundation of suitable size in PCC 1:3:6 type C2 as per Engr-in-Charge complete all as specified and directed.
Material & Labour for repairs/Servicing to AMF Panel of DG set 500 KVA capacity including checking loose connections and tight connection and cleaning inside/out side all connection, replacing all cable glands,thimbles and lugs as per the size of existing cable, applying petroleum jelly on the contactors, providing new insulation tape to bus bars, repair to broken /hanging doors by fixing hinges or welding the door to make it servicable and testing the entire panel board after the completion of servicing up to the satisfication of Engr-in-charge all as directd and specified. (a) Cleaning inside the panel and all incoming and out going feeders i.e includinging MCCB/ Changeover switches/ Contactors thorouly with help of Vaccum Cleaner. (b) Checking the loose connections of incoming and out going feeders and rectifify the same with help of new GI nut bolts and washers (c) Repair/ replacement of burnt out closing coil, tripping coil, shunt coil, SMPS etc. (c) Replacing the burnt out colour coated PVC Sleeve of main and feeder bus bar with appropriated size of New PVC heat shrinkable sleeves (d) Replacing Burnt out Voltmeters/Ammeters/Indicating Lamps. (e) Replacing burnt out control wiring of Ammeter/Voltmeter/Indicating lamps and CT'swith 2.5/1.5 Sqmm copper single core,1100V grade copper conductor cable (Note :- Spares parts/closing coil, tripping coil, shunt coil, indicators etc. will be measured and paid separately .)
Supply only closing coil
Supply only tripping coil
Supply only shunt coil
Supply only RYB indicator AC
Supply only RYB indicator DC 24 Volt
Material & Labour for repairs/Servicing to AMF Panel of DG set 100 KVA capacity including checking loose connections and tight connection and cleaning inside/out side all connection, replacing all cable glands,thimbles and lugs as per the size of existing cable, applying petrolium jelly on the contactors, providing new insulation tape to bus bars, repair to broken /hanging doors by fixing hinges or welding the door to make it servicable and testing the entire panel board after the completion of servicing up to the satisfication of Engr-in-charge all as directd and specified. (a) Cleaning inside the panel and all incoming and out going feeders i.e includinging MCCB/ Changeover switches/ Contactors thorouly with help of Vaccum Cleaner. (b) Checking the loose connections of incoming and out going feeder and rectifify the same with help of new GI nut bolts and washers (c) Repair/ replacement of burnt out closing coil, tripping coil, shunt coil, SMPS etc. (c) Replacing the burnt out colour coated PVC Sleeve of main and fedders bus bar with appropriated size of New PVC heat shrinkable sleeves (d) Replacing Burnt out Voltmeters/Ammeters/Indicating Lamps. (e) Replacing burnt out control wiring of Ammeter/Voltmeter/Indicating lamps and CT'swith 2.5/1.5 Sqmm copper single core,1100V grade copper conductor cable (Note :- Spares parts/DG C6 relay, indicators, DC Charger, contactor etc. will be measured and paid separately .)
Supply only RYB indicator AC
Supply only RYB indicator DC 12 Volt
Supply only DG C 6 relay
Supply only DC Charger 12 V capacity
Supply only contactor 4 pole, 65 to 150 Amp, 415 Volt with contactor coil, integrated auxiliary contacts : 2 NO + 2 NC conforming to IS / IEC 60947-4-1 and compitable with existing AMF panel complete all as specified and directed.
Supply and fix in repair of MCCB 4 Pole, 415 V, 100 Amps with breaking capacity 16 KA complete all as specified and directed.
Supply and fix in repair of MCCB 4 Pole, 415 V, Adjustable type, 125 Amps with breaking capacity 16 KA complete all as specified and directed.
Supply and fix in repair of MCCB 4 Pole, 415 V, 160 Amps with breaking capacity 36 KA complete all as specified and directed.
Supply and fix in repair of MCCB 4 Pole, 415 V, 200 Amps with breaking capacity 36 KA complete all as specified and directed.
Supply and fix in repair of MCCB 4 Pole, 415 V, 250 Amps with breaking capacity 36 KA complete all as specified and directed.
Material and labour for repairing of acoustic enclosure (Canopy) of 100 KVA to 160 KVA capacity including replacement of dameged/ broken hinges and door locks, broken door glasses, removing rust, applying two coats of synthetic enamel paint and making good for both sound proof and weather proof and after repair the canopy to be tested to ensure its functionality and weather resistence complete all as specified and directed by Engr-in-Charge
Material and labour for repairing of acoustic enclosure (Canopy) 30 KVA to 45 KVA including replacement of damaged/ broken hinges, broken glasses and door locks removing rust, applying two coats of synthetic enamel paint and making good for both sound proof and weather proof and after repair the canopy to be tested to ensure its functionality and weather resistence complete all as specified and directed by Engr-in-Charge
Supply and fix fuel tank of capacity 500 Ltrs made of 3 mm thick MS sheet with and including drain plug, air vent, inlet and outlet connection, level indicator and provision for cleaning complete mounted on angle iron frame of size 40x40x5 mm all as specified and directed by Engr-in-Charge.
Material & Labour for repairs/Servicing to Existing LT electric panel including checking loose connections and tight connection and cleaning inside/out side all connection, replacing all cable glands,thimbles and lugs as per the size of existing cable, applying petrolium jelly on the contactors, providing new insulation tape to bus bars, repair to broken /hanging doors by fixing hinges or welding the door to make it servicable, spray painting (silver colour) / powder coating and testing the entire panel board after the completion of servicing up to the satisfication of Engr-in-charge all as directd and specified. (a) Cleaning inside the panel and all incoming and out going feeders i.e includinging MCCB/ Changeover switches with help of Vaccum Cleaner. (b) Checking the loose connections of incoming and out going feeders and rectifify the same with help of new GI nut bolts and washers (c) Replacing the burnt out color coated PVC Sleeve of main and fedders bus bar with appropriated size of New PVC heat shrinkable sleeves (d) Replacing Burnt out Voltmeters/Ammeters/Indicating Lamps. (e) Replacing burnt out control wiring of Ammeter/Voltmeter/Indicating lamps and CT'swith 2.5/1.5 Sqmm copper single core,1100V grade copper conductor cable (Note: The tenders quoted rate per unit shall deemed to be inclusive of taking out burnt MCB/MCCB/Voltmeter/Ampiermeter /CT/LED lamps of any type and description etc and refixing the same)
M&L in repair for Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanized earth strip of size 32 x 6 mm by means of galvanized iron or steel bolts nuts check nuts and washers and other end connected with earthing testing point including providing suitable testing points as directed including funnel, watering pipe of 20mm bore, light grade galvanized iron pipe, wire mesh charcoal of coal dust and common salt in alternative layer all around the earth electrode compacted thickness 15cm with concrete pit in PCC 1:3:6 type C1 50mm thick pre cast RCC 1:2:4 type B1 cover slab set in CM (1:4) re-enforcement with 8mm dia deformed bars @ 15cm C/C and suitable handle of 10mm dia MS round bars, including earth work in hard/dense soil as required complete all as shown in electrical plate No 3 of MES Schedule Part I and testing on completion complete all as specified and as directed. (Note: Earth strip beyond 7.5 m length will be measured & paid separately)
Material and labour for cutting of road/ hard standing n exc 20cm width and n exc 40cm in depth for laying of cable protection pipe including making good the disturbed road/hard standing by providing PCC (1:2:4) type B1 to match with existing surface complete all as specified and directed.
MAURYA CONSTRUCTIONS (BID ID -3357108)
M/S MANGANG RENOVATIONS (BID ID -3357874)
M/s Ritz Marketing (BID ID -3357183)
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .