Signaling work in connection with fencing work in DIWA - PANVEL - ROHA & CSMT - PNVL, TNA (excl.) - Vashi (incl.) Harbour line of Mumbai division.

Supply of PVC indoor cable 1x24x1 mm dia. Color coding of insulation of Inner conductor shall be in eight colour viz, Blue, Red, Grey, Green, Brown, Black, Yellow & white confirming to IRS 76/89 (Amd. 3) or latest.

Supply of Indoor Jumper wire of various colour as per Railways standard practice of type ATC 1x0.6 mm dia. Conforming to IRS/76/89 (Amd.3) of latest.

Supply of Indoor Jumper wire ATC 1x1 mm dia. Conforming to IRS/76/89 (Amd.3) of latest.

Supply of PVC flexible copper cable single core, multistrand 1x16 Sq.mm (126 04 conductor each diameter 0.40 +/- 0.01) as per IS 2465/1984 & IS: 694/2010. with latest amendment if any with insulation thickness of 1.0mm nominal conductor resistance 1.121 ohms/km and test parameters are as per IRS (S) 76/89 (Amd.3)or latest.

Supply of wire 16/0.2 (Blue, Red, Grey, yellow, Brown, Black, White as per site engineer instruction) finolex/polycab/delton make. IRS:S-76/89 (Amd.3), BS: 4808 Part-2. Wire to be procured from RDSO approved vender.

Supply of Program switches with acrylic cover, snap action, base mounting type along with cover and mounting bracket 25A-7 pole 3 position Siemens (3 LAO-25/7Y)/ L&T/HEVELS type. Drg. No.RST.C.106.

Supply of Program switches, snap action, base mounting type along with cover and mounting bracket 63A-7 pole 3 position Siemens (3 LAO-63/7Y)/L&T/HEVELS type Drg.No.RST.C.106.

Supply of Battery charger self regulating floor mounting type with 230 V AC single phase input and output 60 V DC, 20 A as per spec.IRS.S.86/2000 (Amd.4) with latest amendments.

Supply of Battery charger self regulating floor mounting type with 230 V AC single phase input and output 24 V DC, 20 A as per spec.IRS.S.86/2000 with latest amendment for Axle counter application (Amd.4)

Supply of Battery charger self regulating floor mounting type with 230 V AC single phase input and output 24 V DC,30 A t o spec.IRS.S.86/2000 (Amndt-1) with latest amendment for Axle counter application (Amd.4)

Supply of Rubber Mat 5mm thick for use in signaling installation.

Supply of Digital measuring wheel for measuring cable trench/route make: Stanley or Freemens make or similar reputed make.

Supply of Thermo-Shrink cable joining kit (Reinforced) TSF-2 type generally 13 confirming to RDSO specification RDSO/SPN/TC/57/2015 Rev 1 with modified kit contents as per CSTE's Specification No.:CR/SPN/TC/57 (A)/2015 Dt: 06.01.2015 (Table-A) to be suitable for jointing both 10/20/50 pair PIJF and 4/6 Quad cables alongwith sub-kit (Table-B) for armour continuity.

Supply of Electrically operated LIFTING BARRIER complete set without Hand Generator, Operating on 110V AC, with Boom length 9.76M along with one spare boom confirming to RDSO/SPN/208/2012 Ver.2.0 with amendment 1 or latest amendment.

Supply of Paints as per relevant IS specification preferably Asian / Apcolite/ Dulux make in different colour in one kg/2 kg pack

Supply of Epoxy sets consisting of 3kg Gel coat red, 1 kg of thinner and 1kg of hardner. Set shall be of same make. Make: Dr Beck/ASTRAL/3M make.

Supply of 4.5 kg CPO2 type fire extinguisher along with all accesories, extinguisher 17 testing certificate has to be supplied along with - Supply of ISI marked Carbon Dioxide type (BC) fire extinguisher of 4.5 Kg capacity confirming to IS 2878: 2004 from seamless cylinder, with IS marked control value, high pressure mtr., Long discharge hose and horn complete with initial gas charged with carrying handle and wall mounting bracket etc. as required by site Engineer.

Supply of Key Lock Relay with different ward combinations (Three extra set of ward 18 plate for point Machine to be supplied with each relay). Siemens make working on 60V DC/24 DC or functional equivalent without base plates. RDSO/SPN/219/2016 version 1.0 with Amendment No.1 or latest.

Supply, Installation, Testing & Commissioning of Microprocessor based intelligent, addressable, Fire Alarm control Panel with LCD display complying to RDSO/SPN/217/2025 Ver 3.1 or latest modular, 1 loop (minimum 125 detector/devices per loop-expandable to 2 loops) with 320 Character with soft keys for displaying alarm, events and operating functions, Day/Night operation 19 function, Remote maintenance service feature etc. The panel should be multi-protocol i.e. able to support at least 2 different makes of addressable detectors. The panel should have minimum two relay outputs & 1 Monitored Sounder Output. It should have provision to be connected to repeater panels in future. The panel shall capable to operate on 230 volts AC power supply, automatic battery charger, 24 volts, sealed lead acid maintenance free batteries sufficient for 24 hours normal working and then be capable of operating the system for 30 minutes during emergency condition. Panel should be Vds Certified.

Supply of Block filter unit as per IRS:S-68/89 and Block bell equipment as per IRS:TC- 44/88 (Amd. 1).

Supply of Block Bell equipment as per RDSO Drg. No.TCA 15080 and Spec. No IRS-TC- 44/88 (Amd.1) with amendment No. 1 Voltage 24 V DC.

Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92 With holder 1.6 A (System, Rapid or Malnad Make).

Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92 With holder 0.6 A (System, Rapid or Malnad Make).

Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92 With holder 6 A/10A (D- Type Bharat Linder, L&T or HEVELLS Make).

Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92 Without holder 1.6 A (System, Rapid or Malnad Make).

Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92 Without holder 0.6 A (System, Rapid or Malnad Make).

Supply of INDICATIVE TYPE OF FUSE INSERTS. IRS S:-78-92 Without holder 6 A/10A (D-Type Bharat Linder, L&T or HEVELLS Make).

Supply of PPTC Fuse GP 60-185 UL-94 certification (1.6 Amps) for internal / external current. Make: LITTLEFUSE, FUZETEC, TYCO, BOURN, RAYCHEM etc.

Supply of Resisters, condensers, Diodes, LEDs and lugs alongwith bracket and mounting arrangement as per standard Annexure-V of Central Railway.

Lacing thread rolls, black, wax coated (100 mtrs) Each

Design, fabrication and supply of fuse Auto changeover system for 32 Nos external non detorating type fuses or 'G' type fuses from 0.6A Amp to 4A Amp capacities used in signaling circuits. System shall have 8 cards with monitoring arrangement of 4 fuses in one card. As per RDSO spec. RDSO/SPN/209/2012 Ver.2.0 or latest amendment if any. Each

Design, fabrication and supply of fuse Auto changeover system for 24 Nos external non detorating type fuses or 'G' type fuses from 4 A to 10 Amp capacities generally used for point operation circuits. System shall have 6 cards with monitoring arrangement of 4 fuses in one card. As per RDSO spec. RDSO/SPN/209/2012 Ver.2.0 or latest amendment if any.

Supply of Main signal post 140 mm outer dia 3.6 Mtr Length as per spec No.IRS S 6/81 with latest amendments.

Supply of Main signal post 140 mm outer dia 4.6 Mtr Length as per spec No.IRS S 6/81 with latest amendments.

Supply of Main signal post 140 mm outer dia 5.6 Mtr Length as per spec No.IRS S 6/81 with latest amendments.

Supply of Cast Iron Main signal surface base 140mm as per spec No IRS: S-10 and 36 Drg No 2011/M with latest amendments, with CLS Ladder assembly complete for CLS signal 5.5/4.5/3.5 mtrs long as per RDSO Drg no. SA 23156 (Adv), SA 23153 (Adv) & SA 23150 (Adv) Alt.1 respectively with Latest Amendment as the case may be for CLS unit & signal back staging as per extent C.Rly practice.

Supply of Signal No.Plates as per Drg No RST-11393/ SK-842

OFF set bracket 5-1/2" to suit 140 mm dia CLS Post with two no. of "U" Bolts with nut & washer complete as per RDSO Drg No SA-23080 for signals & Routes.

Supply of A/AG/C/P/G/IB Board as per Drg. RST-11444/1(A), RDSO Drg No SA- 39 23460(AG), SA-23461(C) , RST-11445, SA 23456(P), SA 23477(G) & SA 23476-77 (IB) as applicable respectively with Latest Amendment.

Supply of Stop Board / IB Board as per RST-11791 (STOP BOARD)/ RDSO Drg No 7235/B as per extent C.Rly practice.

Supply of different warning Board as per Goods warning Board (SK-784) RDSO Drg No. SA 2380 (Adv), SA 2370/M-, Block section limit Board RDSO Drg No. SA 2373 - Paint and retroreflective arrangement as per Railways drawing.

Supply of Hand Cuff Locks / Godrej Navtal lock with Three common keys.

Supply and Fixing of RE Protective Screens of expanded metal 12 SWG of size 1200 x 1500 mm on signals as per extent practice & as per instruction of Rly engineer at site DRG - No.SK-

Supply of Phenolic 10mm thick sheet, grade P3 in standard size of 1.22x1.22 Mtr as per spec. No. IS 2036 of 1995.

Supply of ARA Terminal blocks with links made of PBT Specn No.IRS/75/2006 (Rev - 2) with latest amendments and RDSO Drg.No.SA-23741A Alt.4., SA-23745 Alt.5, SA-23746, SA-23748 Alt.4, & SA-23756 Alt.3.

Supply of cartridge fuse block made of PBT as per RDSO Drg No SA-23748 Alt 4, SA- 23749 & Spec No.IRS S 75/2006 Rev.02 with latest amendment. Fuse block shall be suitable for round head type voltage fuses.

Supply of round head type non detoriating type low voltage cartridge fuse as per specn No. IRS/S/78/92 with latest amendments - 2A/4A/6A capacity

Supply of Tik-tak, piano type switches, 5 A (as per IS Specification).

Supply of three pole plug and socket 5 Amp (as per IS Specification).

Supply of earth electrode assembly as per Drg.No.CR/S&T/SK-815

Supply and Installation of Lightening & Surge protection device, Single phase + neutral (housed in a suitable impact resistance box) for providing B class protection as per RDSO spec No. RDSO/SPN/165/2012 (Ver 3.0)

Supply and Installation of Lightening & Surge protection device, Single phase + neutral (housed in a suitable impact resistance box) for providing C class protection as per RDSO spec No. RDSO/SPN/165/2012 (Ver 3.0)

Supply of B type choke to specn.No.IRS.S.65/83 (Amd.3 ) with latest amendments.

Supply of adjustable Track Feed Resistance disc type 7.5/15/30 ohms as per RDSO Drg. No. SA 20161-66/M (Adv) with latest amendments ( with phenolic moulded base).

Supply of Channel Pins single groove, galvanised, 7 mm suitable for 4mm dia bonding wire as per spec No. IRS: S 17-75 Revision 3.

Supply of Pre-wired Crank Handle cum key lock relay box (of metal) alongwith LEDs, with approved type push buttons, 8-way terminal strips, string rod, etc. as per Drawing No.RST.C.114

Supply of William stretcher nylong insulation set suitable for ground connection as per RDSO drg No T-10367, T-10368, T-10384 as applicable and to the spec IRS S 23/88 with Amendment No.01 & 40/84 with Amendment No.01 or latest amendments.

Supply of Tongue attachment nylon insulation set consisting of one inlsulating plate as per Drg no: RST-106961 & 3 nos of Ferrules with collars to suite rodding supplied as per RDSO spec & Drg.no: RST-10692

Supply of Gauge Tie Plate nylong insulation as per RDSO drg No: T-10372 Alt2, T- 10368, T-10371 Alt2, T-15083/88/Alt2 & T-11690/Alt2 and to the spec IRS S 23/88 with Amendment No.01 & 40/84 with Amendment No.01 or latest amendments.

Supply of GI bend pipe, B class, 50mm dia for cable entry in point machine alongwith required fixing arrangements as per standard practice on Central Railway. As per Drg No. RST.11835.

Supply of GI pipe, inner dia. 100mm dia. B-class as per spec. No.IS 1239 PT. 1/2004 or latest with sockets and fittings. TATA/JINDAL/ZENITH BIRLA make.

Supply of DIN Channel for the terminals 1 Mtrs each

Fuse terminals block with LED indication up to 2.5 sqmm screw type one in one out (suitable for (400 mA, 630mA, 1 A, 1.6 A, 2 A, 4A, 6.3 A & 10 A ) as per RDSO SPN/189/2004 Ver.03 or latest . (without fuse)

Fuse links of (400 mA, 630mA, 1 A, 1.6 A, 2 A, 4A, 6.3 A & 10A)

Supply of signal group 2 aspect without base plate Siemens make (No.A-RT-RG-A066) or functional equivalent and should be suitable for working with LED based signal lighting unit.

Supply of signal group 3 aspect without base plate Siemens make (No.A-RT-RG-A067) or functional equivalent and should be suitable for working with LED based signal lighting unit.

Supply of signal group, 4 aspect Siemens make (No.A-RT-RG-A057) or functional equivalent without base plates.

Supply of Shunt signal group Siemens make (No.A-RT-RG-A065) or functional equivalent without base plates (suitable for LED signal)

Supply of Point Group RRI, Siemens make (No.RSSK 3515/19) or functional equivalent without base plates.

Supply of Point Chain Group Siemens make (No.RSSK 3515/3) or functional equivalent without base plates.

Supply of Auto signal Block proving Relay Group Siemens make (No.A-RT-RG-A056) or functional equivalent without base plates. Above/

Supply 8-way Terminal strips, made of PBT, isolating barrier type as per IRS-S-79/92 (Amd. 2) & Drg No SA24811 (Alt.2) & SA24812 (Alt.2) with latest amendment.

Supply of PVC flexible copper cable single core, multistrand 1x25 Sq.mm (196 02 conductor each diameter 0.40 +/- 0.01) as per IS 2465/1984 & IS: 694/2010. with latest amendment if any with insulation thickness of 1.2mm nominal conductor resistance 0.780 ohms/km and test parameters are as per IRS (S) 76/89 (Amd.3)or latest.

Supply of QNA1 AC immunized relay, 8F-8B, 24 VDC along with plug, board, retaining clip and connectors conforming to BRS:931A,IRS:S60/78 with Amendment no.1 , IRS:S34/68 with Amendment no.6 & IRS:S23/88 with Amendment no.1

Resin cored wire as per specification No.IS:1921-1975 with Alloying element percentage as 63% SN (Tin) nd / 37% Pb (Lead) with percentage of various impurities not exceeding the values Sb (Antimony 0.2% maximum, Cu (Copper) 0.1% maximum, As (Arsenic) 0.05% maximum, Fe (Iron) 0.02% maximum & other impurities mainly AI, Zn & Cd shall be limited. The flux shall be free from corrosive action as per clause 5.2 & flux percentage may be used as per requirement.

Lacing thread rolls, black, wax coated (100 mtrs) Each

Design, fabrication and supply of fuse Auto changeover system for 32 Nos external non detorating type fuses or 'G' type fuses from 0.6A Amp to 4A Amp capacities used in signaling circuits. System shall have 8 cards with monitoring arrangement of 4 fuses in one card. As per RDSO spec. RDSO/SPN/209/2012 Ver.2.0 or latest amendment if any. Each

Design, fabrication and supply of fuse Auto changeover system for 24 Nos external non detorating type fuses or 'G' type fuses from 4 A to 10 Amp capacities generally used for point operation circuits. System shall have 6 cards with monitoring arrangement of 4 fuses in one card. As per RDSO spec. RDSO/SPN/209/2012 Ver.2.0 or latest amendment if any.

Design, fabrication and supply of fuse Alaram system for monitoring Location fuses (HRC type) of various types with automatic changeover facility alongwith Audio & Visual indications as per technical specifications given in Annexure.unit(1 Number=per fuse)

Supply of Main signal post 140 mm outer dia 4.6 Mtr Length as per spec No.IRS S 6/81 with latest amendments.

Supply of Main signal post 140 mm outer dia 5.6 Mtr Length as per spec No.IRS S 6/81 with latest amendments.

Supply of Cast Iron Main signal surface base 140mm as per spec No IRS: S-10 and 11 Drg No 2011/M with latest amendments, with CLS Ladder assembly complete for CLS signal 5.5/4.5/3.5 mtrs long as per RDSO Drg no. SA 23156 (Adv), SA 23153 (Adv) & SA 23150 (Adv) Alt.1 respectively with Latest Amendment as the case may be for CLS unit & signal back staging as per extent C.Rly practice.

Supply of FIBRE GLASS INSULATING FIRE RETARDENT SHEET OF 10 MM THICKNESS AS PER ISO: 10192-1982, Dielectric strenth -25KV/mm with glass content 25 to 34% in standard size of 1.10x1.10 Mtr as per spec. No.IS:10192-1982

Supply of ARA Terminal blocks with links made of PBT Specn No.IRS/75/2006 (Rev - 2) with latest amendments and RDSO Drg.No.SA-23741A Alt.4., SA-23745 Alt.5, SA-23746, SA-23748 Alt.4, & SA-23756 Alt.3.

Supply of Tik-tak, piano type switches, 5 A (as per IS Specification).

Supply of three pole plug and socket 5 Amp (as per IS Specification).

Supply of Lamp 110V / 24W, 2 pin for Loc.

Supply of earth electrode assembly as per Drg.No.CR/S&T/SK-815

Maintenance Free Earth as per RDSO/SPN/197/2008 or latest consisting of : 1) Copper 18 bond steel electrode 3 Mtr long 17mm dia with copper bonding thickness of min. 250micron & UL listed & marked-01 No. (2) Earth enhancement compound RDSO Approved in sealed bag of 10 kgs - 03 No. (3) Copper strip 150 x 25 x 6mm - 02 No (4) Copper Strip 300 x 25 x 6mm- 01 No (5) 35 Sqmm Copper Cable to connect earth electrode to MEEB - 15Mtr Approx.

Supply of 35 Sq. mm. multistrand single core PVC insulated copper for connecting earth bus bar to earth electrode.

Supply of copper Tape 25x6 mm (Bonding ring conductor) mounted on insulated standoff (1 round).

Supply of 300x25x6 mm Cu equipotential Bus Bar.

Supply of Channel Pins single groove, galvanised, 7 mm suitable for 4mm dia bonding wire as per spec No. IRS: S 17-75 Revision 3.

Supply of PVC jacketed wire rope for Track lead connections. PVC jacketed wire rope 23 should be of Galvanised steel wire rope 6mm dia (6x19 stranded wire with steel core of 6 mm dia) sheathed with PVC 2mm wall thickness, overall thickness being 10 mm. PVC sheath should be made of type 6 compound as per IS 5831 of 1984 Reaffirmed 2001 and steel wire rope as per IS: 2266:2019. Reclaimed for recycled material should not be used.

Supply of 8 SWG GI wire (4mm dia) suitable for track circuit rail bonding. As per IRS Specification S:13-62

Supply of Tuning Unit for AFTC. (Frequency requirement will be given by Railways). Tuning unit should be suitable for existing system.

SUPPLY of Electronic timers for DAC reset arrangement 3 sec to 30 sec with 2NO/2NC contact working voltage 24V/60V DC. Siemens/ABB/L&T or SELEC(642X A programmable electronic timer switch) make.

Fuse terminals block with LED indication up to 2.5 sqmm screw type one in one out (suitable for (400 mA, 630mA, 1 A, 1.6 A, 2 A, 4A, 6.3 A & 10 A ) as per RDSO SPN/189/2004 Ver.03 or latest . (without fuse)

End plate for through terminal block with LED indication.

Fuse links of (400 mA, 630mA, 1 A, 1.6 A, 2 A, 4A, 6.3 A & 10A)

Shorting link insulated Grey in colour Above/

Wiring, fixing & commissioning of modules of fuse 0.6 to 4 Amp rating alarm system having change over arrangement and potential free contact wiring at Datalogger IDF. Etc as per instructions of Railway Engineer. (Module of 32 nos fuses) Each

Wiring, fixing & commissioning of modules of fuse 4 to 10 Amp rating alarm system having change over arrangement and potential free contact wiring at Datalogger IDF. Etc as per instructions of Railway Engineer. (Module of 24 nos fuses)

Excavation and Casting of main signal foundation as per Drg No SK 801 with 03 contractor's own materials including cement and anchor bolts of standard size. The required scaffolding Ferma etc for casting of foundation will have to be brought by the contractor at his own cost.

Erection of CLS post with surface base and signal unit on top or on OFF set Bracket, 04 fixing of front and back staging, ladder and guards, signal name plates/boards if any with contractors own brackets and fixing materials. This also includes erection of auxiliary signals like calling on, shunt signal if any. The work shall be done as per instructions of Rly engineer at site.

Hot dip Galvanizing as per RDSO Specn. ETI-OHE-13 (4/84) - signal post, OFF set Brackets dia 140 mm and length upto 5600 mm.

Hot dip Galvanizing as per RDSO Specn. ETI-OHE-13 (4/84) - Misc M.S. Fabricated items like point roddings, P/D brackets etc. length upto 1200 mm.

Fabrication and fixing of phenolic laminated/Fibre glass sheet in location box by 08 providing all fixtures as per Railway Drawing including fixing of PVC coated/with PVC pipe covered string rods at the back side for cable support with contractor's own materials. The work shall be done as per drg and arrangement similar to SK 783- 1& 2. with latest alterations & as per instructions of Rly engineer at site. a) Single Case

Fixing of cutting in relay bases & wiring of relays with Contractors own material obtained from approved sources in location box as per the instructions of Engineer in charge. Per

Fixing of ARA Terminals and fuse blocks on phenolic laminated sheets and fixing by stainless steel/brass nuts & bolts. This includes provision of two additional holes on the board on either side for cable conductor entry. Per

Termination of cable cores on ARA terminal/fuse blocks in the apparatus cases/ cable termination rack. This includes all associated works of pulling out the cable from underground. The work shall be done as per location plans and instructions of Rly engineer at site.

Excavation and Casting of Apparatus case foundation with contractors Anchor bolts, cement, ballast and other materials. The required scaffolding ferma etc for Casting of foundation will have to be brought by the contractor at his own cost. i) Single Case as per Drg No SK-803

Erection of Apparatus cases. This includes filling of location foundations and plastering .i)Single Case

Installation of earth electrode assembly as per Drg.No.RE/S&T/SIG/Tender/SK726/85 including earth wire connected through GI wire 8 SWG supported on M.S. flat of size 6mm x 40 mm to earth electrode as per drg. No.CR/S&T/SK-815 for sigg. Equipment such as lever frames, 13 apparatus case, signals, relay racks, block instruments, and etc. as per RE manual. The earth value should be less than 10 Ohms including the lead wire. The value should be measured in presence of Rly. supervisor. It should be documented and painted on earth enclosure made of concrete.( only earth electrode will be supplied by Railway). All other material required for provision of earthing will be brought by the contractor.

Fabrication, supply and fixing of various type of MS flat clamps on girder bridges/rocky area on GI pipes/its coupler as per drawing with requisite no. of nut and bolts as per site requirement and as per the instructions of Railway Engineer at site.

Installation, testing and commissioning of the Ring Earth as per RDSO specification 15 No.RDSO/SPN/197/2008 or latest amendment and RDSO drawing no.SDO/RDSO/E&B/001 and 002. All the consumables for mounting the copper tape/bus bar, copper lugs with stainless steel nut and bolts, copper bus bar etc. will be supplied by the contractor free of cost. Material to be procured from the RDSO approved vendor.

Installation of unit earth as per RDSO/SPN/197/ver I or latest, to construct earthing of </=1 Ohm consisting of a digging the earth to required depth, insertion of electrode, filling of earth 16 enhancing compound & construction of chamber, measurement of earth value and all other work of earthing as per code of practice. All the consumables for mounting the copper tape inside the relay room, Exothermic weld materials and tools & fixtures for the welding copper tapes nd Electrodes etc shall be arranged by the contractor.

Connecting main earth electrode to BRC using 35 sqmm copper cable.

Installation of 25x6 mm copper tape (bonding ring conductors) mounted on insulated standoffs (1 round).

Loading, un-loading & transportation of material from the stores of SSE(SIG) depot or any other nominated place & vice-versa. Unit(Per Ton/Per KM=1 set)

Refixing of electrical point machine, ground connection during phase working (Non 20 interlocked working) after removing the existing fitting if any, adjustment if necessary, cable termination, wiring, testing and commissioning of electrically operated point, fixing and connecting point indicator on derail switch if necessary. The work shall be done as per extant practice on C.Rly & the instruction of Rly engineer at site. Unit(PER T/O=1 set)

Fixing of point machine on newly laid turnout on Wooden/MBC sleepers, fixing of ground connections, adjustment and testing with crank handle operations, Removal of ground 21 connection & point machines duly numbered. This will include fixing of bend pipes with welded frame for cable entry to machine. This will also includes necessary adjustment and smithy work, drilling of holes to tounge rails, fitting of insulation for tounge attachment, gauge plate & stretcher bars, cable termination & wiring if required. The work shall be done as per extant practice on C.Rly & the instruction of Rly engineer at site. Unit(PER T/O=1 set)

Excavation of cable trench as per cable route plan, 1.0 mt. deep and 300mm wide along side the track in normal soil/strata, conforming to distances as per cable route plan and refilling after cable laying. This work includes covering of cable laid to trench by loose soil for a layer 22 of 50mm thickness after clearing of route, bushes etc. It shall be ensured that top of the cables laid is at a depth of 0.8 m or more. If it is less, then the width and depth shall be suitably increased and accordingly proportionate payment shall be made. In case depth of trench is not achievable due to site conditions, proportionate payment will be made as per procedure. The work shall be done as per extant practice on C.Rly & the instruction of Railway engineer at site. Drg No SK 805

Excavation of cable trench as per cable route plan, 1.0 mt. deep and 300mm wide along side the track in hard soil, conforming to distances as per cable route plan and refilling after cable laying. This work includes covering of cable laid to trench by loose soil for a layer of 50mm 23 thickness afer clearing of route, bushes etc. It shall be ensured that top of the cables laid is at a depth of 0.8 m or more. If it is less, then the width and depth shall be suitably increased and accordingly proportionate payment shall be made. In case depth of trench is not achievable due to site conditions, proportionate payment will be made as per procedure. The work shall be done as per extant practice on C.Rly & the instruction of Railway engineer at site. Drg No SK 805

Cutting of all types of Roads/platforms (except concrete type) for trenching and 24 excavation to depth of 300mmx300mm wide approx. and refilling after laying of RCC/GI/DWC pipe & to restore them to original condition. The work shall be done as per extant practice on C.Rly & the instruction of Railway engineer at site. Drg No SK 807

Fixing of GI pipes for crossing the culverts, bridges etc. and concreting of ends with brick masonry at both ends as per the instruction of Rly engineer at site.

Digging of trench 1.0 M deep from rail flange/road level (for LC) and, 0.3 Mtr to 0.6 26 Mtrs wide and back filling after placing of DWC/RCC/GI pipe. (Placing of DWC/RCC/GI pipe coverd separately). The ballast disturbed be screened and dressed as required by Engineer-in-charge or his representatives and road tarred immediately. Drg No SK 806

Laying of DWC/RCC pipes alongwith collars / RCC Half round pipes in trenches at places of track and road crossings, platform cutting etc.

Laying of signalling/Power/Telecom cable of various cores/sizes in trenches.

Laying of RCC Trunking and capping and sealing after cable laying as per std practice on C.Rly & the instruction of site engineer.

"Where ever depth of 0.5 m cable trench is not feasible, cable shall be protected as under:- Preparation of cement mixture 1:3:6 with contractor's own materials and spreading cement concrete mixture layer of 100 mm thick over the already laid cables in the excavated trench."

Laying of GI pipes in on bridges/culverts/concrete drain/ mountain ridges etc. with 31 suitable GI bend shall be provided where there is turning of pipe as per instructions of the site engineer. GI Clamps at every 2 m as shown in the drawing to be fixed. Suitable holes to be made in the pipe before laying as per instructions of the site engineer. 100 mm dia. Drg No SK 808

Releasing of cables from old location boxes and taking it into new location boxes. This includes excavating the earth to release the cables. From old location box for taking it into new location. This also includes releasing the old location box and bringing it to nearest station/central cabin. Location (old) will be released only after ensuring all working cables have been shifted in New location. Unit(Per location=1 set)

REMOVAL OF PSC/Wooden SLEEPERS coming in the way of/route of cable trenching, signal/Location foundation/Track Crossing etc. These obstruction will be removed by contractor for ensuring proper execution of related works.

REMOVAL OF Redundant/Old Rails coming in the way of/route of cable trenching, signal/Location foundation/Track Crossing etc. These obstruction will be removed by contractor for ensuring proper execution of related works.

FIXING OF "C" Channel Clamps on Girders along with proper coupling of GI/DWC 35 pipes. The work will be executed as per instruction of site incharge and site incharge may take decision as per site condition. All the fixures, nut bolts, tolls required to fix the channel will be provided by Contractor. Proper safety equipment like Helmet, Retroreflective jacket and whistle, flag is to be made available during execution of work.

Termination of Tail cable inside the point machine through bend pipe this includes preparatory work of pulling the cables, and peeling out the insulation, dressing and lacing after 37 termination etc., pulling of tail cable as per circuit requirement inside point machine through bend pipe, termination of cables on terminal blocks as per instruction of site supervisor the cable shall be entered in such a way that, armouring shall protect the cable near sharp edge of entry point and armouring shall be clamped between pipe fixing bracket and boy of point machine.

"Patching work in old location box consisting 1) Digging of pit, cleaning of earth from 38 all sides, breaking of seal of location boxes removal of sand from location, marking of new cable holes. 2) insertion cable from ground 3) making place for cable termination in old location, shifting ARA, fuse etc after removal and termination including fixing of ARA. 4) Termination of cable in old location. 5) Filling of sand and plastering to all sides upto 50 mm below ground level."

Painting two coats of synthetic enamel paint over one coat of primer on the following after scrapping and cleaning of the surface wherever necessary with contractor own supply of paints. 39 Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge. Epoxy will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.(i)Apparatus Cases Full size.

Painting two coats of synthetic enamel paint over one coat of primer on the following after scrapping and cleaning of the surface wherever necessary with contractor own supply of paints. 40 Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge. Epoxy will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.(ii)Apparatus Cases Half size.

Painting two coats of synthetic enamel paint over one coat of primer on the following after scrapping and cleaning of the surface wherever necessary with contractor own supply of paints. Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- 41 charge. Epoxy will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.(iii)Main signal post with signal Units, Surface base and complete fittings as per Centre Railways standard practice.

Painting two coats of synthetic enamel paint over one coat of primer on the following after scrapping and cleaning of the surface wherever necessary with contractor own supply of paints. 42 Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge. Epoxy will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.(iv)Shunt signal post with signal unit, surface base as per central Railway's Standard Practice.

Painting two coats of synthetic enamel paint over one coat of primer on the following after scrapping and cleaning of the surface wherever necessary with contractor own supply of paints. 43 Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge. Epoxy will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.(v)Track lead Junction Box. (Black enamel outside only)

Painting two coats of synthetic enamel paint over one coat of primer on the following after scrapping and cleaning of the surface wherever necessary with contractor own supply of paints. Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- 44 charge. Epoxy will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.(vi)Point Machine with ground connections complete (Point Machine with Black enamel only outside and ground connections with Red Oxide)

Painting two coats of synthetic enamel paint over one coat of primer on the following after scrapping and cleaning of the surface wherever necessary with contractor own supply of paints. 45 Wherever required contractor shall apply coating of epoxy paint also as per instructions of site-in- charge. Epoxy will be supplied by Railways. NOTE:- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer.(vii)Axle counter devices.

Lettering / Numbering of Signals, Point Machine, Track Lead junction Boxes, Block joints, Apparatus Cases etc.(each item to be taken as One Unit) This work will be carried out as per the standard practice being followed in Central Railway.

Transportation of signaling material/equipments including loading and unloading in 47 10MT vehicle, anywhere to anywhere, and stacking at destination as per instructions of SSE in- charge as per inventory. For carrying heavy materials like cable drums, DG set, Electrical lifting barrier pedstal, IPS, Batteries, Point machine etc.Unit(Per Ton/Per KM=1 set) Above/

Wiring, fixing & commissioning of modules of fuse 0.6 to 4 Amp rating alarm system having change over arrangement and potential free contact wiring at Datalogger IDF. Etc as per instructions of Railway Engineer. (Module of 32 nos fuses) Each

Wiring, fixing & commissioning of modules of fuse 4 to 10 Amp rating alarm system having change over arrangement and potential free contact wiring at Datalogger IDF. Etc as per instructions of Railway Engineer. (Module of 24 nos fuses)

Excavation and Casting of main signal foundation as per Drg No SK 801 with 03 contractor's own materials including cement and anchor bolts of standard size. The required scaffolding Ferma etc for casting of foundation will have to be brought by the contractor at his own cost.

Erection of CLS post with surface base and signal unit on top or on OFF set Bracket, 04 fixing of front and back staging, ladder and guards, signal name plates/boards if any with contractors own brackets and fixing materials. This also includes erection of auxiliary signals like calling on, shunt signal if any. The work shall be done as per instructions of Rly engineer at site.

Termination of tail cable on Main signal units and wiring with contractor own material etc. The work shall be done as per instruction of Rly engineer at site.

Fabrication and fixing of phenolic laminated/Fibre glass sheet in location box by providing all fixtures as per Railway Drawing including fixing of PVC coated/with PVC pipe covered string rods at the back side for cable support with contractor's own materials. The work shall be done as per drg and arrangement similar to SK 783- 1& 2. with latest alterations & as per instructions of Rly engineer at site. a) Single Case

Fabrication and fixing of phenolic laminated/Fibre glass sheet in location box by 07 providing all fixtures as per Railway Drawing including fixing of PVC coated/with PVC pipe covered string rods at the back side for cable support with contractor's own materials. The work shall be done as per drg and arrangement similar to SK 783- 1& 2. with latest alterations & as per instructions of Rly engineer at site. b)Half Case

Fixing of cutting in relay bases & wiring of relays with Contractors own material obtained from approved sources in location box as per the instructions of Engineer in charge. Per

Fixing of ARA Terminals and fuse blocks on phenolic laminated sheets and fixing by stainless steel/brass nuts & bolts. This includes provision of two additional holes on the board on either side for cable conductor entry. Per

Termination of cable cores on ARA terminal/fuse blocks in the apparatus cases/ cable termination rack. This includes all associated works of pulling out the cable from underground. The work shall be done as per location plans and instructions of Rly engineer at site.

Excavation and Casting of Apparatus case foundation with contractors Anchor bolts, cement, ballast and other materials. The required scaffolding ferma etc for Casting of foundation will have to be brought by the contractor at his own cost. i) Single Case as per Drg No SK-803

Excavation and Casting of Apparatus case foundation with contractors Anchor bolts, cement, ballast and other materials. The required scaffolding ferma etc for Casting of foundation will have to be brought by the contractor at his own cost. ii)Half Case as per Drg No SK-804

Erection of Apparatus cases. This includes filling of location foundations and plastering .i)Single Case

Erection of Apparatus cases. This includes filling of location foundations and plastering. ii)Half Case

Installation of earth electrode assembly as per Drg.No.RE/S&T/SIG/Tender/SK726/85 including earth wire connected through GI wire 8 SWG supported on M.S. flat of size 6mm x 40 mm to earth electrode as per drg. No.CR/S&T/SK-815 for sigg. Equipment such as lever frames, 15 apparatus case, signals, relay racks, block instruments, and etc. as per RE manual. The earth value should be less than 10 Ohms including the lead wire. The value should be measured in presence of Rly. supervisor. It should be documented and painted on earth enclosure made of concrete.( only earth electrode will be supplied by Railway). All other material required for provision of earthing will be brought by the contractor.

Installation of unit earth as per RDSO/SPN/197/ver I or latest, to construct earthing of </=1 Ohm consisting of a digging the earth to required depth, insertion of electrode, filling of earth 16 enhancing compound & construction of chamber, measurement of earth value and all other work of earthing as per code of practice. All the consumables for mounting the copper tape inside the relay room, Exothermic weld materials and tools & fixtures for the welding copper tapes nd Electrodes etc shall be arranged by the contractor.

Connecting main earth electrode to BRC using 35 sqmm copper cable.

Installation of 25x6 mm copper tape (bonding ring conductors) mounted on insulated standoffs (1 round).

Installation of 300x25x6 mm Cu equipotential Bus Bar.

Excavation of cable trench as per cable route plan, 1.0 mt. deep and 300mm wide along side the track in normal soil/strata, conforming to distances as per cable route plan and 20 refilling after cable laying. This work includes covering of cable laid to trench by loose soil for a layer of 50mm thickness after clearing of route, bushes etc. It shall be ensured that top of the cables laid is at a depth of 0.8 m or more. If it is less, then the width and depth shall be suitably increased and accordingly proportionate payment shall be made. In case depth of trench is not achievable due to site conditions, proportionate payment will be made as per procedure. The work shall be done as per extant practice on C.Rly & the instruction of Railway engineer at site. Drg No SK 805

Fixing of GI pipes for crossing the culverts, bridges etc. and concreting of ends with brick masonry at both ends as per the instruction of Rly engineer at site.

Laying of DWC/RCC pipes alongwith collars / RCC Half round pipes in trenches at places of track and road crossings, platform cutting etc.

Laying of signalling/Power/Telecom cable of various cores/sizes in trenches.

Lettering / Numbering Termination particulars, equipments names etc., legibly and neatly inside location boxes.(a)Full Case.

Lettering / Numbering Termination particulars, equipments names etc., legibly and neatly inside location boxes.(b)Half Case. Above/

Supply of single section Digital Axle Counter (SSDAC) with two detection point with reset arrangement and vital relay box as per RDSO/SPN/177/2012 Ver.03 or Latest. Each set consist of following:- a) High frequency TX coil and RX coil (Each set consist of web mounting type TX coils-2 Nos. RX coils-2 Nos along with 10 mtr cable-2 sets), b)Track side digital axle counter unit.-2 nos. c) 24V 6F/4B, 1000 ohm "Q" type relay Box duly wired - 2 Nos. d) Clamp with detector plates and hardware etc-4 Nos e) Reset Box 2 Nos ii) Mushroom/Location Box suitable for housing Track side equipment (2 Nos.) 2) Transportation, Installation testing & commissioning:- Transportation, Installation testing & commissioning of equipment field training (one man day per set) at site or as desired by site Engineer. These includes:- a) Foundation & erection of Track side Equipment i.e. 01 Mushroom/ Location Box (If required). This includes supply of all associated materials., b) Individual Earthing of all detection Point for the OEM recommended earth value certified by OEM site engineer. This includes supply & installation of maintenance free earth materials and exothermic bonding and other connecting cable etc as per Railway practice (As per RDSO Spec.no: RDSO/SPN/197/2008 or latest. Resetting equipment to the connected to the EI Ring earth. c) Installation to be carried out by OEM certified Engineer. 3) Tool Kit consisting of :- a) Digital True RMS multi meter of suitable make for above Digital Axle counter system with probe set- 1no b) Train Simulator (High frequency)-1 no c) Extender Card - 1 no d) Dummy wheel-1 no e) Different type of spanners suitable for above Digital Axle counter - 1 set f) Torque wrenches suitable for the aboe-1 no g) Screw driver set suitable for the above - 1 set. h) Carrying Bag for Tools - 1 no i) 6 nos Electrostatic Discharge Wrist Band for cards/ modules protection.

Item Breakup - C1-NON SOR ITEM

Supply of Microcontroller based programmable Numbers 15.00 static switchingmodule of naturally air cooled onlywith an at a glance LCD displaysuitable for break-less switchingbetween two DC supplies of UP to40A for 20-110VDC.(Inspection Agency- RDSO)

Installation and commissioning ofmicrocontroller Numbers 15.00 basedprogrammable static switchingmodule of naturally air-cooled onlywith an a glance LCD displaysuitable for break-less switchingbetween two DC supplies of UP to40A for 20-110VDC. (Inspection Agency-Consignee)

Supply of AC & DC low current clampmeter with Numbers 10.00 range 1 mA to 100 A or higher make FLUKE, RISHABH, or KOICO.(Inspection Agency- Consignee)

Casting of cement concrete to protectS&T cum equipments and laid cables, abovepipes etc by concrete mixture ofcement, sand, stone in the ratio of1:2:4 using 25 mm graded stoneaggregate as per instruction of site incharge of railways. Concrete is to becasted with the help of suitable sizeshuttering form as per siterequirement. Concrete is to be cured forsufficient time as per standard practiceson railways(Inspection Agency- Consignee)

Industrial Compartments. Made out of 18/19 gauge CR sheet with individual locking arrangement (1) size of locker 36 in Width) x 19 in (depth) x 6 foot (Height) (2) with 2 legs of each size 5 inch (H) x 3 inch (W) x 19 inch (D) (3) Size of each compartment 10.74 in (H) x 16.25 in (W) x 19 in (D) 2 in rows and 6 in columns with Siemens gray colour make.(Inspection Agency-Consignee)

Repairing of location foundation with masonary Numbers 100.00 work. This also includes cleaning the locations, sand filling in the location and plastering inside the location(Inspection Agency-Consignee)

Supply of DPM meter (AC measurements) range 0 Numbers 10.00 to 750VAC operating on 230V AC auxillary suply equivalentto MECO/Rishi orsimilar.(Inspection Agency-Consignee)

Supply of DPM meter (DC measurements) range 0 Numbers 10.00 to 200VDC operating on 230V AC auxillary suply equivalentto MECO/Rishi orsimilar.(Inspection Agency-RDSO)

Supply of GPS tagging featured cable route Numbers locator/tracer set suitable for detecting underground armoured optic fiber cable (OFC) and signaling cables with LCD Graphic Display active/passive modes and depth range. 3M-10m. Model STLOC10 GPS make Stanlay or equivalent. (Inspection Agency-RDSO)

Twist Adaptor 19mm weldon for 13 mm (part no. Numbers 210245FS(Inspection Agency-Consignee)

Twist adaptor 19 mm Weldon for 7.2 mm (Part Numbers 10.00 No: 210253FS)(Inspection Agency-Consignee)

Twisted Drill size 13 x 19 mm (Part no. 5223118) Numbers 12.00 (Inspection Agency-Consignee) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

Battrey oprated drill m/c cutter 22.5 mm Rail TCT Numbers 10.00 Cutter 22.5x 55 mm (Part No: 240289)(Inspection Agency-Consignee)

Hiring anddressingground/dismantlingstructures ,Removalof jungle, clearing ofearth, lowering highcess etc., along sidethe track between upand down linesobstructing drainagesof rain water, clearingof bushes obstructingvisibility at curvesand Level Crossingswith all lead and liftetc. complete and asdirected by theEngineer-in- charge.All labour, tools andplants consumablesstores includingsupply of JCB/Hitachiwith crew to beprovided by thecontractor at his owncost. The contractorshall arrange roadpermit for vehicle forall the States ofoperation, as perinstructions ofengineer in- chargeand vehicle shall notbe more than threeyears old. Paymentshall be made foractual working hoursat site.(Inspection Agency- Consignee)

Battery operated High performance LED area with Numbers 10.00 3000 lumens output light weight & unbreakable as per specification attached (1) Product specification M18 HAL -+ M18 NRG 502B (2) Article No. 493345123 (3) Battery compatibility all Milwaukee M18 Batteries (4) Battery capacity (Ah) 5.0 (5) Battery type Li ion (6) No of Battery charger supplied 01 No. (7) Full Battey charging time 59 min (8) Max light output 3000/1500/650 (9) Max run time battery 2/4/9 hr. (10) No. of batteries supplied 2 Nos. (11) Voltage (AC) (V) 220-240 (12) Voltage (DC) (V) 18 (13 Wight with battery pack (kg) 3 (14) One year onsite warranty, installation & training free of cost mak Eibenstock/Milwaukee or equivalent.(Inspection Agency-Consignee)

"Printing & Supply of various Signal maintenance Numbers 500.00 register paper size A-4, Thickness 70 GSM Minimum, 'A' Grade white paper 9 X 11"" size Both size printing Black colour with hard bound with top cover color printing having label, name, number of register etc.. Register would be contained total 200 Nos of pages on average. Register names, Format details are attached as annexure-A IN NIT (UNITNUMBER SHOULD BE READAS PER REGSITER) (Inspection Agency- Consignee)"

High speed steel twist drill bit dia 7mm/13 mm Numbers 250.00 suitable for battery operated drill machine make Eibenstok. Drill bit make: MAKITA/BOSCH/FEIN or Other reputed brand(Inspection Agency- Consignee)

"RETRO REFLECTIVE STICKER: Retro Reflective Square Self Adhesive, Yellow: 900Sq.feet, Red:500Sq.feet, Foot Black:100Sq.feet. Make:3m,(Inspection Agency- Consignee)"

Supply & commissioning of Thermo vision imager Numbers alongwith drive & power tools & equipments spares as per RDSO's specn. No. TI/SPC/OHE/TIPS/1030(6/2005) REV-1 or latest(Inspection Agency-Consignee)

Execution of S & T work related toenginnering Job /Signalling block ofCTR/TTR/TSR or others, in oneblock, five unskilled manpowerhave to be provided during blockfor S&T connection removing &refixing as per Railway siteengineer instruction.(Inspection Agency-Consignee) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

Supply of Cable fault locator as per specification. Numbers Make : Tempo, Stanlay or Greenlee. Module SIDEKICK PLUS 1155-5001(Inspection Agency- Consignee)

Supply of Smoke detector (Optical) Apollo make Numbers 50.00 or similar for fire alarm system.(Inspection Agency-Consignee)

Supply of Fire alarm Control cum Indication Panel Numbers equipped with 4 zone cards together with electronic hooter & all other acessories. (Inspection Agency-Consignee)

Installation of Fire Alarm System (this includes Numbers fixingof smoke detectors over relay racks, CT racks, powerpanel, power equipments, indication panel and otherfire prone areas), wiring of smoke detector & systemmonitor with contractor's wiring & fixing material. Thework shall be done as per extant practice on C. Rly &the instruction of site engineer(Inspection Agency-Consignee)

Supply of DC-DC Convertor 24-40V DC/5A/10A as Numbers 40.00 per RDSO/SPN/165/2012(Ver3.0) or latest, including all accessories required for making a slot in the DCDP, holding Statcon IPS DC-DC convertor of lower rating, compatible for DC-DC Convertor 24-40V DC/10A working at rated Load. (Inspection Agency-RDSO) Total 9018598.72

Item Breakup - C2-NON SOR ITEM

Supply of counting head ZP 43 V complete with Numbers sensor for Siemens make MSDAC (Inspection Agency Consignee)

Supply of GLF Tape Abration resistance with Numbers 50.00 masting compound in size of 51 mm x 1.27mm x 2.6 Mtrs Rolls of Stanvac Chemicals, Permacel, ICC, Nitco or 3 M make. (Inspection Agency Consignee)

Supply of portable hole drilling machine in rail Numbers web suitable for holding 7-8 mm drill bit. (Inspection Agency Consignee)

Supply of DWC pipe 40 mm inner dia, 50 mm Metre outer dia, in length of 6 mtr or different as per convience of OEM with couple and socket as per BS EN 50086-1 and BS EN 500086-2-4 (Inspection Agency Consignee)

Casting of cement concrete to protectS&T cum equipments and laid cables, abovepipes etc by concrete mixture ofcement, sand, stone in the ratio of1:2:4 using 25 mm graded stoneaggregate as per instruction of site incharge of railways. Concrete is to becasted with the help of suitable sizeshuttering form as per siterequirement. Concrete is to be cured forsufficient time as per standard practiceson railways (Inspection Agency Consignee)

Supply of HSS straight shank jobber Drill ground Numbers 50.00 flute to IS 5101/DIN 338/ BS 328 ISO of size 7.1 mm of Addison, JK make of similar (Inspection Agency Consignee)

High speed steel twist drill bit dia 7mm/13 mm Numbers 50.00 suitable for battery operated drill machine make Eibenstok. Drill bit make: MAKITA/BOSCH/FEIN or Other reputed brand (Inspection Agency Consignee) MUMBAI-CST-DIVISION-S AND T/CENTRAL RLY

"12V 42AH LEAD ACID SMF BATTERY (GEM OFFER Numbers 20.00 EXIDE 12.0 Volt Volt Lead Acid Battery (EXIDE)Model | Exide Power safe Plus EP 42-12 AS PER GEM CONTRACT) (Inspection Agency Consignee)"

Battery operated High performance LED area with Numbers 3000 lumens output light weight & unbreakable as per specification attached (1) Product specification M18 HAL -+ M18 NRG 502B (2) Article No. 493345123 (3) Battery compatibility all Milwaukee M18 Batteries (4) Battery capacity (Ah) 5.0 (5) Battery type Li ion (6) No of Battery charger supplied 01 No. (7) Full Battey charging time 59 min (8) Max light output 3000/1500/650 (9) Max run time battery 2/4/9 hr. (10) No. of batteries supplied 2 Nos. (11) Voltage (AC) (V) 220-240 (12) Voltage (DC) (V) 18 (13 Wight with battery pack (kg) 3 (14) One year onsite warranty, installation & training free of cost mak Eibenstock/Milwaukee or equivalent. (Inspection Agency Consignee).

Arrangment of battery operated rail core drill Numbers alongwith additional 18 mm TCT rail core drill.Maximum core cutting capacity 36mm,rated speed 250/450ZRPM, Battery type Li-on,Battery voltage 50V,Battery pack capacity 4AH,Number of battery supplied-2No. Charger-1No. Special design pressurised internal spindle cooling to give maximum life of core cutter by avoiding heating.3 sets of of 22,13,16,7.1 gauge drills adapters with drill bit is to be provided along with the machine.weight of machine with battery-18.5Kg Make- Eibenstok,Bosch,KPTL. (Inspection Agency Consignee)

WELD LESS MODULAR TYPE SS MEDUIM SIZE Numbers LOCATION BOX (Inspection Agency Consignee)

WELD LESS MODULAR TYPE SS POST BOX Numbers LOCATION BOX (Inspection Agency Consignee)

Supply of Reset box for MSDAC R D S O / S P N / 1 7 6 / 2 0 0 5 . (Inspection Agency Consignee) Total 1962107.46