Master Plan Works for Arulmigu Arunachaleswarar Thirukkovil, Tiruvannamalai

Amount

Removing old paint from iron surface with sand paper (W-0113)

Removal of Cut Stone Slabs (W-0021)

Removal of Corrugated Iron Sheet Roofing without roof timbers (W-0026)

Dismantling of Brick Masonry in cement mortar walls under 3m high (W-0015)

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

For Temple Internal , External and Pallikondan pattu

Refilling with excavated soil (other than sand) complying with standard specification for filling in foundation and basement. W-0075

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

For Temple Internal

For Temple External

For pallikondanpattu

Supplying and Filling Gravel in 'foundation and basement with filling crushed stone sand in layers of not more than 15cm.thick well rammed watered and compacted -1m3 etc., complete complying with standard specification..

For Temple Internal

For Temple External

Construction of Granular Sub base by providing well graded material (25 mm to 4.75 mm IRC HBG metal @ 65 %,4.75 to 2.36mm IRC HBG metal @20%&2.36 mm below IRC HBG metal @15%)& (the material passing 425 microns sieve shall have liquid limit and plasticity index not more than 25 & 6% repectively) spreading in uniform layers with motor grader on prepared surface mixing by mix in place method with rotovator at OMC and compacting with three wheel 80-100 KN capacity and finished in accordance with the requirements of the specification and thickness as per approved plans or as directed by the Engineer (Mix -in - place method) ..

Cement Concrete 1:3:6 (One cement, Three crushed stone sand and Six hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers.

For pallikondanpattu

Cement Concrete 1:5:10 (One cement, Five crushed stone sand and Ten hard broken stone) using 40 mm gauge hard broken jelly for flooring including laying, consolidating, finishing, rendering the top surface rough to receive the floor, curing, etc. complete complying with standard specification. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers.

For Temple Internal

For Temple External

Providing and laying in position, standardised concrete Mix M-20 Grade in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation & Basement Concrete

For Temple Internal

For Temple External

Foundation & Basement Concrete

For Temple External

Providing and laying in position, Standardised Concrete Mix M-25 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cementcontent of 350 kglms and maximum water cement ratio of 0.50, including admixture (plasticiser / superplasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation & Basement Concrete

For Temple Internal

For Temple External

Ground Floor Concrete

For Temple Internal

For Temple External

First Floor Concrete

For Temple External

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Foundation & Basement Concrete

For Temple internal, External and Pallikondanpattu

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silveroak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For Temple Internal , External And Pallinondanpattu(For 0.00-3.30m)

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

For Temple Internal , External And Pallinondanpattu(For 0.00-3.30m)

For Curved surface of all RCC items of work

For Temple Internal , External And Pallinondanpattu(For 0.00-3.30m)

Brick work using Country Bricks of size "8-3/4" x 4-1/4" X2-3/4" in Cement Mortar 1:5 (One cement and five crushed stone sand) including curing neat finishing, etc., complete complying with standard specifiction.

In Foundation and Basement

For Temple Internal

For Temple External

Brick work using using Country Bricks of size 8-3/4" x 4-1/4" X2-3/4" in Cement Mortar 1:6 (One cement and six crushed stone sand) including curing neat finishing, etc., complete complying with standard specifiction.

In Ground floor

For Temple Internal

For Temple External

In First Floor

For Temple External

Brick partition walls using best quality using Country Bricks of size 8-3/4" x 4-1/4" X2-3/4" in Cement Mortar 1:3 (One Cement and Three crushed stone Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

For Temple Internal

For Temple External

R.R Masonary in cement mortar1:5(one cement,and five crushed stone sand) for foundation and basement including simultaneously pointing above ground level with the same mortar etc.,complete complying with standard specification as directed by departmental officers

For pallikondanpattu

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

For Temple Internal

For Temple External

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers.

For Temple External

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering sand), 12mm thick in all floors including curing etc., complete complying with standard specification and as directed by the departmental officers.

For Temple Internal

For Temple External

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

For Temple internal, External and Pallikondanpattu

Painting the wall two coats with approved weather proof water Based Exterior Emulsion paint over one primer coat of over cement plastered wall surface ect., complete including brushes etc complying with standard specification as directed by departmental officers

For Temple internal

Supplying and fixing of Teak Wood ornamental temple type door shutter using Teak wood frame of size 150mm x 120mm of double leaf in position using 50mm thick planks shutters with necessary brass hinges 125x30mm - 10 nos ,brass aldrops 300x16mm - 2 nos,tower bolts 400mm long x 12mm dia - 4 nos ,brass handle 200mm long - 4 nos, aluminium door stopper - 2 nos including two coat of varnishing and inlcuding labour charges for fixing in position etc.,complete as directed by the departmental officers. ( Fittings provided shall bear ISI mark. The quality, design of panel door and brand of door shutter and furniture fittings should be got approved by the Executive engineer before use)

For Temple internal, External and Pallikondanpattu

Best Indian Teak Wood wrought and putup for frames of doors, windows, ventilators, cupboards and any other similar joinery works with necessary plugs, rebates for shutters, plaster grooves on all faces etc., including labour charges for fixing hold fast complying with revevent standard specification etc., in all respects.

For Temple internal, External and Pallikondanpattu

Supplying and fixing of soild core Flush shutters with Teak ply on both sides with teak wood lipping all-round 35 mm thick including cost and labour for fixing the Aluminium furniture fittings viz. 2 no. of Door Handle 3 nos. of 5" Aluminium Butt hinges, 2 nos. of 6"x1/2" Tower bolt,1no. of 10"x5/8" Aldrop, 1no. of Rubber bush,1no. of door stopper with rubber bush, with required screws etc. all complete complying with relevant standard specifications and as directed by the departmental officers.

For Temple internal, External and Pallikondanpattu

Supplying and fixing wood polymer composite board solid door frame and 25mm thick shutter frame corners of extruded outer size 75mm X 50mm the inner core more rigid WPC composite with minimum shore hardness of 55 and bulk density 0.8 Grams per cubic centimeters. The frame shall be fixed to the wall using 10 X 100 mm long MS screw through the frame through the pvc fastener. Minimum three numbers of screw to be provided for each vertical member. The overall size of frame shall be with suitable rebate for housing shutter and shutter consist of 25mm polymer composite board single core exhaust with one side embo printing design. To avoid duplicate from the printing design shall have logo of the WPC board shall be bount aid proved by kept official. The shutter shall be provided with 3 Nos of 4” SS butt hinges, 2 Nos of 4” Stainless Steel handles, 3 Nos of 6” Stainless Steel tower bolts with required Stainless Steel screws including labour charges for fixing the shutter frame, shutter and furniture fittings in position and finished smooth with template etc., all complete in all respects complying with relevant standard specification and as directed by the departmental officers

For Temple internal, External and Pallikondanpattu

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x6mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers

For Temple internal, External and Pallikondanpattu

Providing and fixing factory made uPVC white sliding glazed window upto1.50 m in height dimension comprising of uPVC multi-chambered frame with inbuilt roller track and sash extruded profils duly reinforced with 1.60 ± 0.2 mm thick appropriate dimension of uPVCextruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body withsingle nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8mm size for fixing frame to finished wall and necessary stainless steel screwsetc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled withweather proof silicon sealent over backer rod of required size and of approve quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.

For Temple internal, External and Pallikondanpattu

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

For Temple internal, External and Pallikondanpattu

Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive ofhood covers, transportation charges etc

For Temple internal, External and Pallikondanpattu

Supplying and fixing of mild steel grills to windows and ventilators including cost of necessary screws and cost of applying priming coatof paint etc.,- 1 Kg

For Temple internal, External and Pallikondanpattu

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over One coat pf zinc chromite primer in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should begot approved by the Executive Engineer before use on works.)

For Temple internal, External and Pallikondanpattu

Polishing the teak wood door with two coats of best French (Lac) polish with approved quality and brand over a coat of bee's waxing including preparing the wooden surface to receive polishing, etc., complete complying as per the standard specifications. (The make, quality and colour of french polish, bees vax should be got approved by the Executive Engineer before use on works.)

For Temple internal, External and Pallikondanpattu

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

For Temple internal, External and Pallikondanpattu

Paving the floor with best quality Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

For Temple internal,

For Temple External,

Supplying and laying of Joint free Rectified Glazed Ceramic Flooring Tiles 305 x 305 x 8mm (Anti Skid) thickness laid in cement mortar 1:3( One of cement and three of sand) 20mm thick for flooring including cost of tiles fixing in position cutting the tiles to the required size wherever necessary pointing the joints with white/ colour cements neatly curing, finishing including cost of cement mortar etc complete and as directed by the departmental officers. Note:( The colour and quality shall be approved from the E.E before use only one particular size of ceramic wall tiles to be used for one building)

For Temple internal,

For Temple External,

Dadooing walls with following best approved quality, white glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two crushed stone sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

For Temple internal,

For Temple External,

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

For Temple internal,

For Temple External,

Paving the floor with Fully polished Rajastan kota stone slab of size 600 x 600 of 18 / 20mm in all floors laid in of cement mortor 1:3 (one cement three crushed stone sand), 20mm thick and pointed with colour cement neatly including polishing with polishing stone and oxalic acid etc., so as to perfectly smooth and glossy and including hire charges for polishing machine and power consumption charges etc. The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

For Temple internal,

For Temple External,

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use

For Temple internal,

Paving the floor with pre-polished concrete anti-skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

For Temple internal,

Refixing cutstone Slab and pointing lime mortor including all labour charges etc complete.,

For Temple internal,

Providing cutstone flooring machine cutting edges 600x600mm not less than 100mm thick top surfaces dressed and pointing lime mortor including all labour charges etc complete., (Three line Dressing)

For pallikondanpattu

For pallikondanpattu

Providing cutstone flooring machine cutting edges 600x600mm not less than 100mm thick top surfaces dressed and pointing lime mortor including all labour charges etc complete., (Single line Dressing)

For Temple Internal

For Temple External

Supplying and laying of interlocking Paver blocks of 63 mm thickness using rubber mould, approved make with grey colour including cost of conveyance of interlocking blocks and filling sand and spreading of sand to a thickness of 3 cm for cussion below the interlocking blocks and consolidating, vibrating labour charges for laying to proper level slope etc. as directed by the dept. officers (Design and colour of interlocking blocks should be got approved by EE before using)

For Temple Internal

Supplying and laying of interlocking Paver blocks of 83 mm thickness using rubber mould, approved make with grey colour including cost of conveyance of interlocking blocks and filling sand and spreading of sand to a thickness of 15 cm for cussion below the interlocking blocks and consolidating, vibrating labour charges for laying to proper level slope etc. as directed by the dept. officers (Design and colour of interlocking blocks should be got approved by EE before using)

For Temple Internal

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between.The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete complying with relevant standard specification and as directed by the departmental officers.

For Temple Internal , External And Pallikondanpattu

FALSE CEILING WITH GYPSUM PLAIN TILES Providing and fixing true horizontal level false ceiling using SAINT - GOBAIN GYPROC or Equivalent make with 24 mm Grid system using hot dipped galvanised Steel Section, exposed surface chemically cleaned caping prefinished in backed polyestar paint wall angle of size 24mmX24mm used in the periphery of the ceiling fixed to the wall partition R.C. Column bandwalls with the help of screws at 600mmc/c. Main runner of size 32X24mm suspended at 1200mm c/c max by using securely fixed to the structural soffit of R.C.C. slab by using 6mm Nylon Rawl plug at every 1200mm (Max) and 1200mm long Cross Tee of size 24X24mm to interlocked between Mainrunner at 600mm c/c (max) to form a grid of 1200mmX600mm. 600mm long Cross Tee of size 24X24mm is inserted to form a grid of 600mmX600mm and finally tiles laying with 12mm Gypsum plain Tiles (600mm x 600mm) and Painting with two coat of plastic emulsion paint over one coat of primer.

For Temple Internal , External And Pallikondanpattu

Supply and Fixing Polycarbonate Sheet 6mm thick. (M-0718)complete complying with standard specification and as directed by the departmental officers.

Supply & Fixing of FRP Panels thickness of 6 mm mixture of calcium carbonate, fiberglass and resin. a pebble texture or smooth texture front side. Panel color shall be per specification quality standards are (complies with ASTM D5319): complete complying with standard specification and as directed by the departmental officers.

For Temple Internal ,

Supplying and fixing Toughned glass of thickness 12mm over the Trusses and fins at spacings corresponding to the width of the glazing panels that Spacings of 1.5 m . using appropriate attachments to stainless steel rod, or wire hangers. , cantilevered arms with pivot supports as per standarad specfications and as directed by the department officers The rate is inclusive of the charges for materials , cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete complying with relevant standard specification and as directed by the departmental officers.

For Temple Internal ,

Supplying and fixing of prepainted Galvanized iron PUP PANEL 50 mm thick Roof covered with Top sheet heat resistance at bottom layer of polyurethene bottom of GI Sheet - colour coated - Galvanuume sheet the cost including all material cost, fixing , labour charges , cost of self threaded screws, Conveyance charges etec. complete as directed by departmental officers . The open edge of pupsheet covered with Galvanume sheet tightly

For Temple Internal ,

Supplying and fixing Relevant steel tubular box section including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

For Temple Internal ,

Supplying and fixing Relevant steel tubular box section including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

For Temple Internal ,

Weathering course in brick jelly lime concrete using broken brick jelly of size 25mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the departmental officers.

For External

For pallikondanpattu

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

For External

For pallikondanpattu

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

For Internal

For pallikondanpattu

Ornamental Brick work in LIME MORTAR 1:2 mix using II Class Ground Moulded Chamber Burnt Bricks of size 9" x 43/8" x 23/4" all vari vargams, moulds, sthambas, mukapatram, koodu, nasi, and all ornamental brick work complete panchavarnam agaraies, karnakoodus etc forming core walls rajagopuram/vimanams complete in cluding cement al labour chages in kalkaram

For External

Ornamental Brick work in LIME MORTAR 1:2 mix using II Class Ground Moulded Chamber Burnt Bricks of size 9" x 43/8" x 23/4" all vari vargams, moulds, sthambas, mukapatram, koodu, nasi, and all ornamental brick work complete panchavarnam agaraies, karnakoodus etc forming core walls rajagopuram/vimanams complete in cluding cement al labour chages in kalkaram

For Temple Internal

For Temple External

Providing vargapoochu over the corewalls of Vimanams/Gopurams, with lime martor.1:1.5 complete including shaping the mukhapathram, mahannasi,koodu all arnamental works to proper shape, by embedding broken bricks or shaped/chiselled bricks, rough - plastering with Lime mortar.1:1.5and finishing with final ornamental plastering and nayam theervai including cost and conveyance of all materials labour therefore, lifting of materials, all woeking in heights curing with water etc, complete - including all extra for folding and including clearing the debris from the vimanams/ Gopurams - Upto 25'0" height Excluding Kalkaram

For Temple External

Painting water based with multicolour (Panchavarnam ) good Emultion paint complete for the Vimanams/Gopurams, including cost and conveyance of all materials, labour charges includingArtist painter, working in heights , lifting of materials, cost of brushes etc., complete - which include all extra for foldings - Upto 25'0" height

For Temple Internal

Providing new sudhai vigrahams in the vimanams and Rajagopurams with galvanised iron rod reinforcement of suitable dia with binding wires wherever necessary, shaping the core with broken bricks set in Lime martor.1:1.5 finishing the same with Lime martor.1:1.5, bringing go the correct shape (Lakshana in conformity with silpa sastra inclusive of special ornaments, weapons, peedam etc., Complete and providing Lime martor.1:1.5 Nayam theervai wherever necessary, inclusive of cost and conveyance of all materials, such as cement broken bricks, sand G.I rods,binding wire, all labour for working in height, curing lifting of materials etc., complete, including cement painting 2 coats iver a primary coat (one vigraham is accountable with one head, 4 hands with weapons , ornamental costumes etc, as per prathima Lakshana, vigraham height is measurable from the crown top to the bottom of foot only. If peetam is provided the rate with peetam may be adopted as detailed thereunder).

Painting water based with multicolour (Panchavarnam ) good Emultion paint complete for the Vimanams/Gopurams, including cost and conveyance of all materials, labour charges includingArtist painter, working in heights , lifting of materials, cost of brushes etc., complete - which include all extra for foldings - Upto 25'0" height

Upto 5 feet length 0 to 5 feet

above 5 Feet length upto 10 feet length

Above 10 Feet length upto 14 feet length

Labour Charges for cutstone ornamental works dressing, fixing, finishing etc complete Complying with standard specifications

Chitra vanam

Pristharam - Uthiram,Kambu,Eluthagam

Pavukkal

Vyalavari

Thoon

Koodu

Scaffolding charges for Vimanams and Gopurams with casurina posts coconut or palm trees wherever necessary for main, form work and providing with net lawn / PVC mesh coverings, providing ladder arrangements, country wood plank for working, inspection etc. complete, hire charges only for erection, maintenance and removing the same on completion of the work. Vimanam / Gopuram

upto 15' - 0' height

For Pallikondanpattu

upto 50' - 0' height

For Temple External

Providing expansion joint of 12.5mm wide in between RCC twin columns from top of pedastal to full height including filling the inner space with suitable non-absorbent, flexible and well compressible filler materials of approved quality and brand; finishing the sides of RCC columns with polysulphide sealents for a depth of 7.5mm on either side covering the inner space filled with filler materials as above etc., complete complying with standard specifications and as directed.

For Temple Internal , External And Pallikondanpattu

Planting of Song of India Plant ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge

Water supply Arrangement

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc.,complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

110 mm Dia

For Temple Internal , External And Pallikondanpattu

160 mm Dia

Supplying, laying and jointing UPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

50 mm Dia

For Temple Internal , External

32 mm Dia

For Temple Internal , External

25 mm Dia

For Temple Internal , External

20 mm Dia

For Temple Internal , External

Supplying and fixing of GM Gate valve following Dia heavy duty labour for fixing etc, all complete and as directed by the departmental officers., (The quality and brand of fittings should be got approved from Executive Engineer before use).

50 mm GM Gate

For Temple Internal and External

32mm GM Gate

For Temple Internal and External

Supplying and fixing of GM Wheel valve following Dia heavy duty labour for fixing etc, all complete and as directed by the departmental officers., (The quality and brand of fittings should be got approved from Executive Engineer before use).

32 mm Wheel valve

20 mm Wheel valve

Supply and fixing in position of best Indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

For Temple Internal and External

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm White glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

For Temple Internal and External

Supply and fixing in position of best Indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

For Temple Internal and External

Supplying and fixing of Health faucet including cost of fittings labour for fixing etc, all complete and as directed by the departmental officers., (The quality of fittings should be got approved from Executive Engineer before use).

For Temple Internal and External

supplying and fixing of marble of 0.61*1.22m.,18/20mm thick in all floors for urinal partition including for labour charges for fixing and polishing etc.,Complete complying with satandard specifications and as directed by departmental officers

For Temple Internal and External

Supplying and fixing in position best quality and approved make Indian made white glazed earthernware wash hand basin of size 550 x 400mm ( without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

For Temple Internal and External

Supplying and fixing in position best quality approved make white glazed earthernwere sink of size of 600 x 450 x 200mm including cost of 32mm dia CP waste coupling, 32mm dia PVC waste pipe with rubber plug and chain, 15mm dia brass nipple including fixing the sink in position and testing for leakages etc., complete complying with standard specificationsexcluding CI brackets. [The sink and specials should be got approved by the Executive Engineer before use on works]

For Temple Internal and External

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works).

For Temple Internal and External

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.5mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

For Temple Internal and External

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

For Temple Internal and External

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

For Temple Internal and External

Supplying and fixing approved best quality brass CP towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

For Temple Internal and External

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Nahani Trap of size 100 x 75mm with stainless steel gratings

For Temple Internal

For Temple External

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three crushed stone sandand Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.

For Temple Internal

For Temple External

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

75mm dia PVC soil / waste pipe

For Temple Internal and External

110mm dia PVC soil / waste pipe

For Temple Internal and External

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and UPVCving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to oriUPVCnal condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive EnUPVCneer before use on works).

For Temple Internal and External

elbow

door elbow

Door Tee

elbow

door elbow

Construction of INSPECTION CHAMBER following clear sizes including earth work excavation, CC 1:5:10 of 10 cm thick and brick work in Cement Mortar 1:5 [One cement and Five sand] using best quality of second class Table Mould Bricks of size 9" x 43/8" x 23/4" with Plastering with Cement Mortar 1:3 [One Cement and Three Plastering Sand] 12 mm thick to inner and outer sides and wearing coat 1:3:6 [One Cement, Three crushed stone sand and Six Aggregate] 15 cm thick and covered with precast slab 5 cm thick etc., complete complying as directed by the departmental officers as per standard specification.

For Temple Internal

For Temple External

For Temple Internal

For Temple External

For Temple Internal

For Temple External

Supplying and Fixing the PVC water tank super thick of approved quality and best quality conforming to ISS and with ISI mark of the following sizes including cutting threading and fixing PVC specials but excluding cost of such specials.etc., complete complying with standard specification.

For Temple Internal and External

Supplying and erecting in position of following liters capacityIndustrial Model Reverse Osmosis Water-cum-Purifier todeliver Potable Water with World Health Organisation (WHO)Standards with following accessories.(a) MS Skid - 1 No.(b) Media 11054 No. Vessel with 20 nb Multiport Valve (withMedia Pubble and Fine Sand and Activated Carbon Filling) set(c) Feed Pump 0.50 HP – 1 No.(d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No.(e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic(USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No.& Pressure Gauge - 2 Nos.(f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., LowPressure Switch - 1 No., Level Switch - 1 No. & NecessaryCPVC Pipes and Fittings.The system shall be provide with Two Panel Control Systemwith necessary Stainless Valves and Fittings and Float Controletc. The rate should be inclusive of all civil works, wherevernecessary to install the System in position and intact.

(50 Litres)

(250 Litres)

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

For Temple Internal and External

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4 kg. / sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers

For Temple Internal and External

Supply and delivery of Electric Monoset centrifugal pump conforming to IS9079:2002 as amended from time to time, with CI FG 200 Casing ,hydraulically and dynamically balanced Bronze grade LTB-2 impeller, impellerring and casing ring, stainless steel shaft capable of discharging requiredquantity of water against a total head noted below due to all causes. Pumpshall of BEE 3 Star Rated and capable of discharging the specified quantityat the head noted at the minimum NPSHA at site conditions. The shut offhead shall be atleast 25% over and above the head at duty point. The pumpshall be suitable for operation in AC three phase , 415 V+/- 10% , 50 Hz +/-5%. Squirrel cage induction motor for continuous operation. The speed ofthe Pump and Motor 300 LPM

For Temple Internal and External

BOREWELL ARRANGEMENTS

Geophysical Investigation charges for carrying out new borewell etc, complete

Drilling of 150 mm dia bore well in Hard Rock area using DTH rig including cost of transportation charges for rig and others supporting vehicle etc.

150 mm Cs type

150 mm Bore cap MS

150 mm dia Casing Pipes assembly

125 lpm x 125 m head

Supply and delivery of 2.50 Sq.mm PVC insulated and sheathed 3 core flat type copper cable confirming to IS 694/1990 with ISI mark.

Supply and delivery of MS Kiosk of size 0.75m x 0.45m x 0.75m made up of MS angle of size 50mm x 50mmx4mm alround covered with 16 gauge MS sheet and kiosk door made up of MS plates of size 25 mm x 3 mm including cutting, welding, grinding, locking arrangements and labour charges etc.

50 mm GM Non Return Valve

50 mm GM gate valve

50 mm Flange set

50 mm dia GI pipe

50 mm dia UPVC column pipe for downward extention of pump

50 mm GI Coupling

50 mm GI bend

50 mm GI Union

50 mm MS Clamp set

32 Amps Porcelain fuse unit (500 V)

Supply and run of 4 x 6 sq.mm. (84/0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in 32mm dia GI pipe (Class 'B') suitably bent at both ends with necessary angle iron up right and end supports for mains .

Supply and run of 4 x 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V on 7 / 20 GI bearer wire for service connection mains .

Labour charges for Errection of Supplied Submercible Pump Set in Deep Bore Well including connection of submercible cable all charges

ELECTRICAL ARRANGEMENTS

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with painting of Suitable colour for Open PVC Light point / fan point (for electronic regulator))

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End.

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling and switch drop portion PVC rigid pipe concealed in wall with PVC accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with painting of Suitable colour for Open PVC Light point / fan point (for electronic regulator) ( 5 points / Coil) Higher End

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling and switch drop portion PVC rigid pipe concealed in wall with PVC accessories with Module GI switch box in flush wall with 6A one way module switch with module front plate with painting of Suitable colour for Open PVC Light point / fan point (for electronic regulator) ( 6 points / Coil) Higher End

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC Rigid pipe on wall and ceiling and switch drop portion PVC rigid pipe concealed in wall with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with painting of Suitable colour with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire for Open PVC conduit Plug point ( 8 points / Coil) Higher End .

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no. 6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection by 2.5 sq.mm. PVC insulated SC unsheathed copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point ( 8 points / Coil) Higher End

Fittings & Fan

Supply and fixing of 4' 20W LED fitting with LED on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting (Higher end)

Supply and fixing of 15W LED bulb for BH point

Supply and fixing of 6W LED Mirror fitting with LED with PVC unsheathed copper leads from terminals to the fitting (Higher end)

supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting

supply and fixing of 18W LED square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of 15W LED Wall washer light Up/down light fitting onWall with PVC unsheathed copper leads from terminals to the fitting (Higer End)

Supply and fixing of 15W LED COB Spike light fitting on ceiling with PVC unsheathed copper leads from terminals to the fitting (Higer End)

Supply and fixing of 60W LED Well Glass outdoor Down light fitting for Arch on ceiling with PVC unsheathed copper leads from terminals to the fitting (Higer End)

Supply and fixing of Recess mounted Adjustable 12W LED Down light fitting on false ceiling with PVC unsheathed copper leads from terminals to the fitting (Higer End)

Supply and fixing of 80W LED flood light fitting on ceiling with PVC unsheathed copper leads from terminals to the fitting

Supply and fixing of 50W LED flood light fitting on ceiling with PVC unsheathed copper leads from terminals to the fitting (Higer End)

supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting .

supply and fixing of 6 Metre Length Single Bracket GI Steel Tubular Pole with Base Plate(250 x 250 x 6mm) 76.10mm OD x 3.65mm Thick x 6000mm Length 6 duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour .

supply and fixing of 6 Metre Length Double Bracket GI Steel Tubular Pole with Base Plate(250 x 250 x 6mm) 76.10mm OD x 3.65mm Thick x 6000mm Length 6 duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 2 nos of 48W LED street light fitting with LED (Higher end) for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour .

supply and fixing of 6 Metre Length Pole with Base Plate(250 x 250 x 6mm) 76.10mm OD x 3.65mm Thick x 6000mm Length duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 2 nos. 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 2 nos of 50W LED Flood light fitting with LED (Higher end) on suitable special angle brackets with clamps with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour .

supply and fixing of 6 Metre Length GI Steel Tubular Pole with Base Plate(250 x 250 x 6mm) 76.10mm OD x 3.65mm Thick x 6000mm Length duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 50W LED Flood light fitting withLED (Higher end) on suitable special angle brackets with clamps with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour .

supply and fixing of 6 Metre Length GI Steel Tubular Pole with Base Plate(250 x 250 x 6mm) 76.10mm OD x 3.65mm Thick x 6000mm Length duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 2 nos. 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 2 nos of 80W LED Flood light fitting with LED (Higher end) on suitable special angle brackets with clamps with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour with Concreteing & Construction of masonary pedastal for fixing the post with connections. .

Supply, Erection of 8m Free Standing Single Arm Bracket 8 sided Octogonally continously tapered structured pole with base plate of size 300 x 300 x 12mm as per IS-875 with following specification. Bottom Pole Dia - 130mm Top Pole Dia - 70 mm Thickness of Pole - 3 mm The pole should be hot dip galvanized confirming to BESN ISO 1461 with thickness of 65 Micron octongonal post with supply and fixing of 80W LED street light fitting with 1no 6A SP MCB switch,2/4 way connector on suitable hylem sheet for switch control with Concreteing & Construction of masonary pedastal for fixing the post with connections.

Design, Supply , Testing and commissioning of 10 Meters Mini mast lighting unit Bajaj Philips make of ISI equivalent complete with hot dip galvinized and suitable for 45 Met/sec wind Velocily and above. The Mini mast structure should have hend hence. Single ring and provided with galvanized lantern carriage suitable for and with 4 Nos of 150W LED Luminaries with manual ladder arrangement with safety Rung &feeder pillar Box with Automatic timer system including wiring etc, complete as specified in the relevant ISS.

Design, Supply , Testing and commissioning of 10 Meters Mini mast lighting unit Bajaj Philips make of ISI equivalent complete with hot dip galvinized and suitable for 45 Met/sec wind Velocily and above. The Mini mast structure should have hend hence. Single ring and provided with galvanized lantern carriage suitable for and with 6 Nos of 150W LED Luminaries with manual ladder arrangement with safety Rung &feeder pillar Box with Automatic timer system including wiring etc, complete as specified in the relevant ISS.

Erection of the High Mast by providing Concreting 1:2:4 Mix R.C.C masonary foundation pedestal. The RCC pedestal projection should be 30 cms above the ground level. The feeder pillar box should also be mounted in RCC pedestal with projection of 30 cms above the ground level & foundation suitable to the safe bearing capacity of the soil at 12T /M2 at 1.5m depth of below ground level and necessary galvanized foundation bolts nuts washers and Anchor plate & Tmeplate etc. complete as per standard specification of IS -875-1987.

supply and fixing of 1200mm (48") sweep AC ceiling fan complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 600mm down rod with fan clamp with side plates and cross arm of size 450mm (18")

supply and fixing of 1200mm (48") sweep AC ceiling fan complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

supply and fixing of 1400mm (56") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 600mm down rod with fan clamp with side plates and cross arm of size 450mm (18")

supply and fixing of 1400mm (56") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm (18")

supply and fixing of 400mm) sweep AC Wall Mounting fan with wall mounting clamp with Connections

Supply and fixing of 300mm (12") sweep (Heavy duty) AC exhaust fan complete without provision of hole in the wall .

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan

Supply and fixing of 375mm (15") sweep (light duty) AC exhaust fan complete without provision of hole in the wall

Supply and fixing of louvers shutters arrangements for375 mm (15") sweep light duty AC Exhaust fan

Run of Mains

Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour

Supply and Run of 2 of 2.5 sq.mm. (36/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade insuitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting ofsuitable colour

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.

Supply and run of 2 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade insuitable PVC rigid pipe concealed in wall and ceiling with contiinuous earth wire connection of 14 SWG TC wire andmaking good of the concealed portion with suitable colour.

Supply and run of 4 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour.

Supply and run of 4 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour.

Supply and run of 4 of 6 sq.mm. (84 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth Wire connection of 14 SWG TC wire with painting of suitable colour

Supply and Run of 4 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 4 sq.mm. PVC insulated SC unsheathed copper wire with painting of suitable colour.

Supply and run of 3 Core 2.5 sq.mm. Copper wire in Suitable PVC rigid pipe concealed in wall and ceiling with making good of the concealed portion with suitable colour

Supply and Laying of 3 Core 2.5 sq.mm. Copper wire in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Wall Socket

Supply and fixing of 2nos.6A two module 5 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 2nos.6/16A two module socket , 2 nos. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End.

Supply and fixing of 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End .

Supply and fixing of 1 no. 16A 3 pin two module socket with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End .

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug)

Supply and fixing of 32A DP MCB with sheet steel enclosure in flush wall with earth connection (Higher end)

Supply and fixing of 32A 4P MCB with sheet steel enclosure on wall with earth connection (Higher end)

Supply and fixing of 40A 4P RCCB with sheet steel enclosure on wall with earth connection (Higher end)

Supply and fixing of 63A 4P RCCB with sheet steel enclosure on wall with earth connection (Higher end)

DB'S & Piller Box

Supply and fixing of 4 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB as incoming and 2 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 1 no 32A 3P MCB,9 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 6 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 3 nos 32A 3P MCB,9Nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 6 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 18 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 6 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 2 nos 32A 3P MCB,12Nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

supply and fixing of 6 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board ( with MCCB Incomer ) with double door (metal door) with 1 no. 125 A 4 P MCCB switch as incoming and 2 nos. 63A 3P MCB , 12 nos. 6A to 32A SP MCB as outgoing with suitable cable end box on wall with earth connection only. Higher End .

Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 24 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End.

Supply and fixing of pillar box made up of 16SWG MS sheeet of size 3'x 3'x2' with lock and key arrangements with Suitable AI frame leg support with concrete and construction of masonry pedestal to house 1 no 12 way SP MCB DB ,1 no 32A DP MCB,10 nos 6A/32A SP MCB,L& T 4 pole Contactor MCX-3 32A,Havells 24 Hour Analog timer Switch DHTED 30016,3Nos Backlite 4Way Connector,3Nos Backlite 2Way Connector with earth conection and inter conection only Higer End.

Supply and fixing of pillar box made up of 16SWG MS sheeet of size 3'x 3'x2' with lock and key arrangements with Suitable AI frame leg support with concrete and construction of masonry pedestal to house 1 no 4 way VTPN MCB DB ,1 no 63A 4P MCB,12 nos 6A/32A SP MCB,L& T 4 pole Contactor MCX-3 32A,Havells 24 Hour Analog timer Switch DHTED 30016,3Nos Backlite 4Way Connector,3Nos Backlite 2Way Connector with earth conection and inter conection only Higer End.

Supply and fixing of pillar box made up of 16SWG MS sheeet of size 3'x 3'x2' with lock and key arrangements with Suitable AI frame leg support with concrete and construction of masonry pedestal to house 1 no32A 4P MCB with encloser,L& T 4 pole Contactor MCX-3 32A,Havells 24 Hour Analog timer Switch DHTED 30016,3Nos Backlite 4Way Connector,3Nos Backlite 2Way Connector with earth conection and inter conection only Higer End.

LTCT Meter Box

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit (500V) 32A neutral link and earth link (1" x 1/8" copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit

Supply and fixing of 32A aerial fuse unit (500A) on suitable 100 x 100mm TW concealed box with hylem sheet on the tapping pole with necessary clamps

Supply and fixing of TNEB meter board suitable for 32A three phase service connection with 3 Nos. 32A fuse unit (500V) 32A neutral link and earth link (1" x 1/8" copper flat) on TW plank of size 600mm x 450mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit

Supply and fixng of TNEB meter board suitable for 3 phase 63A service connection made up of suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1/2 feet of 6mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 63A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with earth connection complete.

Supply and fixng of TNEB meter board suitable for 3 phase 100A service connection made up of suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1-1/2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 100A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with earth connection complete.

UG Cable

Supply and Laying of 2 x 6 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clarnping of 2 x 6 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.

Supply and clarnping of 2 x 6 sq.mm. PVC LTUG armoured cable with 19mm GI pipe on post or on wall with MS clamp.

Supply and fixing of brass cable gland for 2 x 6 sq.mm. PVC LTUG armoured cable with earth connection .

Supply and Laying of 2 x 10 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clarnping of 2 x 10 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.

Supply and clarnping of 2 x 10sq.mm. PVC LTUG armoured cable with 19mm GI pipe on post or on wall with MS clamps.

Supply and fixing of brass cable gland for 2 x 10 sq.mm. PVC LTUG armoured cable with earth connection

Supply and Laying of 2 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clarnping of 2 x 16 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and clarnping of 2 x 16sq.mm. PVC LTUG armoured cable with 32mm GI pipe on post or on wall with MS clamps)

Supply and fixing of brass cable gland for 2 x 16 sq.mm. PVC LTUG armoured cable with earth connection

Supply and Laying of 4 x 10 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clarnping of 4 x 10 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.

Supply and clarnping of 4 x 10sq.mm. PVC LTUG armoured cable with 32mm GI pipe on post or on wall with MS clamps.

Supply and fixing of brass cable gland for 4 x 10 sq.mm. PVC LTUG armoured cable with earth connection

Supply and providing cable end termination of 4 x 10 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and Laying of 4 x 16 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clarnping of 4 x 16 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps.

Supply and fixing of brass cable gland for 4 x 16 sq.mm. PVC LTUG armoured cable with earth connection

Supply and providing cable end termination of 4 x 16sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and Laying of 3 1/2 x 25 sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clarnping of 3 1/2 x 25 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and clarnping of 3 1/2 x 25sq.mm. PVC LTUG armoured cable with 32mm GI pipe on post or on wall with MS clamps

Supply and fixing of brass cable gland for3 1/2 x 25 sq.mm. PVC LTUG armoured cable with earth connection

Supply and providing cable end termination of 3 1/2 x 25sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and Laying of 3 1/2 x 50sq.mm. PVC armoured LTUG cable in suitable size HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good.

Supply and clarnping of 3 1/2 x 50 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for3 1/2 x 50 sq.mm. PVC LTUG armoured cable with earth connection

Supply and providing cable end termination of 3 1/2 x 50sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

EARTHING

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Supply and run of 1 of No.8 SWG GI wire for earth connection

Earthing as per the ISI specification with an earth electrode of 2.10 metre Class 'B' GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mm x 6mm with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry

Earthing as per PWD standard with an earth electrode of 2 metre Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry worK.

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps / supports on wall / floor / ground for earth connection

Supply and fixing of 100 A Three phase 500V 4 Pole Change over Switch on suitable angle iron frame work with MS cable entry boxes with earth connection only

62.5 KVA DG Set

Supply, erection, testing and commissioning of 62.5 KVA Diesel Silent Generator set 0.8 PF 3 Ph, 415V, 50 HZ with AMF Panel as Details below. A.Engine: Water cooled Diesel Engine type suitable for generating application with a Shaft output of suitable capacity of 83 BHP at 1500 RPM under NTP conditions. As per the BSS 5414/ISO 3046 The Engine Shall comprise the following standard Fittings.(Kirloskar/Cummins/Equivalent) B.Alternator: Capacity of 62.5/50 kw/36 kw, 0.8 PF self exited, self regulated design to run a 1500 RPM under NTP condition confirming to BS 5000 /IS13364(part II) 1992 to be coupled directly to the Diesel Engine and Test Certificate. (Kirloskar/Stamford/Equivalent) C.Battery: 1No.12V 88/100 AH Battery with copper leads and terminals, Battery Make EXIDE/AMCO/AMARON

.Acoustic Enclosure: supply of acoustic Enclosure for 62.5 KVA Diesel Generator Set. The Acoustic enclosure is made of 1.6/2 mm thick CRCA sheets in munsel Green shade and s Structural Sheet metal base frame Painted in Black. The walls of the enclosure are insulated with the retardant foam so as to comply with the 75 DBA at mtr sound levels specified by Ministry of enforcement.

I The enclosure should be completed with 1. Arrangement for power cable for connection. 2. Residential exhaust silencer, with flexible base arrangements. 3. Suction louvers. 4. Discharge Louvers. 5. Openable and lockable doors on both sides with air tight Neoprene rubber gasket. 6. Lifting arrangements. 7.Interior lighting arrangements J. Erection, Testing and Commissioning of the genset comprising the following: 1. Providing suitable concrete foundation with plain cement concrete 1:2:4 with sand cushion all around and alternator with acoustic enclosure. 2. Erection of generator set complete with acoustic enclosure, fuel tank, engine control Panel, standard control Panel, base frame complete on the above foundation and lifting arrangements. 3. First charging of lub oil and first charging of Battery

Supply and installation of exhaust piping of sufficient length with suitable MS pipes so as to extend outside the generator room with necessary thermal insulation.

Supply and providing RCC Bed concereting for 62.5 KVA DG set

PA SYSTEM

supply and installation of 32 watts wall mounted speaker ( Higher end) with suitable supports with connections

Supply and Installation of 500W PA Mixer Amplifier (Higher end)

Supply and Installation of 12U Wall Rack(Higher End)

Supply and Installation of Cordless Mic UHF(Higher End)

supply and installation of 75 inches LED TV (with full HD with following features. Resolution 3840 x 2160, HDMI , audio in, built in speaker , 24/7 operation. (Higher end)

Supply and Installation of TV Socket on sutiable module box with front plate

Supply and Run of Armoured CO-AXIAL RG-11 Cable for TV in sutiable PVC rigid pipe on wall or on ceiling with connection.

Supply and Run of 2 core 1.5 sq.mm shielded copper speaker wire in sutiable PVC rigid pipe on wall or on ceiling with connection

FURNITURE

ADUPPU For Dosa, Appam & Boonthi Body: It is made out of SS 304 Grade 16 SWG SS Sheet rame Fabric+D13:D32S Plate Cutting Top Covering: 4 Side covering. Side glass wool & fire brick Insulation with SS 4' Square Chimney Pipe Burners: T 78 Burner 1 Nos Leg: 1 1/2' SS 304 Grade pipe with adjustable boot Dimension: 34" OD x 26" ID x 30" Ht

DOUBLE BURNER (PULIYOGARA) Frame: 1 1/4” x 1/4” MS Angle Top & Cover: 16 SWG & 18 SWG 304 Grade SS Sheet Leg: 16 SWG 1 1/2” 304 grade SS square tube With adjustable nylon boot Cast Iron Grate : 016” Burners: G10 2 No Dimension: 54” x 24” x 18” Ht

LPG GAS LINE WORK 10 MANIFOLD SYSTEM MS 1/2' Gasline Pipe , 1/2' MS Bend, 1/2' MS Elbow, Gas Line Union, 3/8 MS BUSH, Clamp, 1/2' GAS Line Dummy -1, Red Paint-1/2L, Wood- 1 Pack, 1/2' Ball Valve -4 , Wooden Screw- 1 Packet, Rod- 1 Packet, 1/2' Hex Nipple, 1/2' Tee,4' Reg,2' Reg,Meter,Adaptor,NC Valve, Flexible Hose, Caller & Other Unit Fitting Materials. Inclusive of Labour Charges

BATTER STAND Top: 16 SWG SS Sheet. Bottom: 18 SWG SS Sheet. Leg: 16 SWG 1 1/2” SS square tube With adjustable nylon boot Dimension: 16” x 16” x 32” Ht

DELIVERY STAND WITH OIL FILTER Made: It is made out of 18 SWG / 16 SWG SS 304 Grade Sheet Fabricated Filter: 22' x 22' x 8' Depth (Both Side Tapper with SS Stand With Oil Collection Tray Dimension: 22” x 22” x 30” Ht

SS PULVERIZER Made: It is made out of Fully SS Sheet Fabricated. Food Contacting SS 304 Grade 8' SS Pulverizer Motor: 2 HP, Three Phase

SS BATTER MIXER Made: It is made out of Fully SS Sheet Fabricated. Food Contacting SS 304 Grade Gear Box Setup Motor: 1 HP, Three Phase Capacity: 50 Kg

SS TRAY It is made out SS 1.2 mm 304 Grade N4 Sheet Fabricated Dimension: 18" x 16" x 2" Depth

SS TRAY It is made out SS 1.2 mm 304 Grade N4 Sheet Fabricated Dimension: 21" x 21" x 4" Depth

AL VATTA WITH LID Aluminium Vatta with LID Dimension: 26" ID x 15" Ht

SS RICE STAINER Stainless Steel SS Stainer for Rice with Cut Dimension: 24” OD x 18" Ht

SS THUDUPPI Stainless Steel Thuduppi Dimension: 7" OD Head + 31" L Handle

SS PLATFORM STAND (FOR STORE) Leg 1 1/2' Square Pipe. Frame & Support 1 1/2' x 3/4', 3/4' Square Pipe Dimension: 96" x 24" x 6" Ht

SS STORE PLATFORM STAND (FOR STORE) Leg 1 1/2' Square Pipe. Frame & Support 1 1/2' x 3/4', 3/4' Square Pipe Dimension: 48" x 24" x 6" Ht

SS THUDUPPI Stainless Steel Thuduppi Dimension: 7" OD Head + 25" L Handle

SS CHARMY Stainless Steel Charmy Dimension: 6" OD Head + 24" L Handle

SS DELIVERY TROLLEY Top: 5' Depth SS Dismantle Tray Bottom: Under Shelve with 3 Side SS Covering (Handle Side Open) Leg & Handle: It is made out of SS 304 Grade 1.6 mm 1 1/2' Sq. Pipe Fabricated Top & Bottom Tier Attached with 4 Nos of 6' wheels Dimension: 40" x 36" x 38" Ht

DOSA STORAGE TRAY WITH STAND It is made out SS 304 Grade Sheet Fabricated Tray Dimension: 44" x 44" x 5" Depth Stand Dimension: 29" Ht + 5" Tray Depth

SS OIL KADAI LID Stainless Steel Dimension: 32" OD

SS DOSA DELIVERY TRAY Stainless Steel 1.2 mm SS 304 Grade N4 Dosa Delivery Tray 100 Nos of Dosa Capacity with Lid Dimension: 30" x 30" x 8" Depth

SS PROVISION RACK - 5 TIER (FOR STORE) Made: SS 304 Grade 1.2 mm Sheet Fabricated 5 Tier SS Rack Covering: 3 Side SS Covering Leg: 1 1/2' SS 304 Grade Sq Pipe with adjuatable nylon boot Dimension: 84" x 20" x 84" Ht

DINING TABLE SEATING BENCH FIXED TYPE Top: 18 SWG SS 304 Grade N4 Sheet Fabricated Leg: 1 1/4" Sq Pipe, Bench Attached to 1 1/4" Round Pipe Capacity: 4 Nos Size: 92" x 21" x 30" Ht

Supply and fixing Chrome plated metal Three seater should be got approved from the Executive Engineer before use on work

SUB TOTAL

PRIDE CONSTRUCTIONS (BID ID -1108384)