Provn of 01x Guard Room alongwith Guard Post and Special Repairs to 06x SWT at Khalsar under AGE BR-II of GE Partapur

Amount

M&L for surface excavation n.exc. (not exceeding) 30cm deep and averaging 15cm deep and getting out in hard/dense soil.

M&L for excavation in trenches, n.exc. 1.5m wide and n.exc. 1.5m in depth; for foundations, etc. or shafts, wells, cesspits, manholes, pier holes, etc. n.exc. 10sqm on plan and n.exc. 1.5m in depth and getting out in hard/dense soil.

M&L for cement concrete type D2 1:4:8 (40mm graded aggregate) in foundations, filling and mass concrete.

M&L for reinforced cement concrete (Design mix) M-30 (20mm graded stone aggregate) as in foundations, including raft, footings, foundations beams, plinth beams; bases for columns, etc. basement slabs, under reamed piles and mass concrete.

M&L for reinforced cement concrete (Design mix) M-30 (20mm graded stone aggregate) as in columns, pillars, piers, posts and struts

M&L for reinforced cement concrete (Design mix) M-30 (20mm graded aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like.

M&L for reinforced cement concrete (Design mix) M-30 (20mm graded aggregate) as in Beams, cantilevers, bressummers, lintel over 1.5m span.

M&L for TMT bars mild steel bars, 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-500D.

M&L for TMT bars mild steel bars, 5 mm dia and over upto and including 10mm dia in stirrups, spaces and binders

M&L for Pre-cast cement concrete Type C1, 1:3:6 (20mm stone aggregate) block masonry with solid blocks, exc. 10 cm in width and setting in CM 1:6, complete.

M&L for providing precast cement concrete Type C1, 1:3:6 (20mm stone aggregate) solid building blocks or slabs 10 cm thick (with plain or interlocking joints as directed) setting in CM 1:6 complete, in walls.

M&L for rendering 10mm thick on fair faces of brick work or concrete surface finished even and smooth (without using extra cement) in CM 1:6

M&L for rendering 15mm thick on fair faces of brick work or concrete surface finished even and smooth (without using extra cement) in CM 1:4

M&L for rendering 5mm thick on fair faces of brick work or concrete surface finished even and smooth (without using extra cement) in CM 1:3 on ceiling.

M&L for 100mm thick Cement Concrete 1:4:8 type D2 using (40mm graded aggregate as in sub base.

M&L for 25mm thick Cement Concrete 1:2:4 type B1, (20 mm graded aggregate) as in flooring.

M&L Screed bed or bedding layer of mortar 15mm thick in Cement Mortar 1:6 for laying floor finishes.

M&L for Non Skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tiles exceeding 0.06sqm but not exceeding 0.11sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match.

M&L for Glazed ceramic coloured tiles in vertical surfaces 300 x 200 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match.

M&L 9mm thick Pre- laminated particle board, interior grade, prelaminated one side with, decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work at wall.

M&L 9mm thick Pre- laminated particle board, interior grade, prelaminated one side with, decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work at ceiling.

M&L second class softwood plain filllets, rectangular in section, clean swan, secured with nails exc 13 and n.exc 25 Sqcm.

M&L second class softwood plain fillets, bullnosed, splayed, chamfered or rounded on one edge or face n. exc 3 Sqcm.

S&F Plain framed, factory made panelled shutter 35mm thick (two panel) 2nd class hardwood rail and stile with lock rail and panel 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS 1003 (Part-I) Kiln seasoned and chemically pressure treated

S&F Plain, solid, straight chowkats of 2nd class hardwood and frames wrought, framed rebated on solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed.

S&F 150mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed.

S&F 100mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed.

S & F 250mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed.

S & F butt hinges 100mm, medium weight, cold rolled mild steel and fixed.

S & F butt hinges 75mm, medium weight, cold rolled mild steel and fixed.

S & F 150mm mild steel pressed handles, oval type, stove enamelled black.

S & F 100mm mild steel pressed handles, oval type, stove enamelled black.

S&F 30cm long hold fast conforming to Fe.290. Gde-E-165 of Sectiion 25x6mm

S & F glazed and skeleton shutters of 2nd class hardwood in 25 mm, open rebated and prepared to receive glass,gauze,etc.(without sash bars),edges of framing, plain,chamfered or rounded.fitted with cut and mitred beads for securing glass,etc;sizes of members of shutters as specified in SSR Part -I, section 8, clause 8.24(a);supplied and fitted to chowkats

S & F 3.00mm sheet glass, ordinary quality and glazing with oil putty in square n. exc 0.5 sq.m in each pane.

S & F in repairs vitreous china water closet sqatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests (excuding flushing cistern and flush pipe) incl making good complete all as specified and directed

S&F PVC valveless, syphonic action type 10.00 ltrs flushing cistern, low level white with inlet, ball valve, float and handle including brackets.

S&F PVC Connections 15mm size with PTMT nuts of length 450mm

S&F 20mm outer dia 3-layer PP-R poly-propylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stavlized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceiling or floors etc.

S&F 15mm bore bib taps cast copper alloy with crutch or butterfly handle screwed down ,screwed for iron pipe or brass ferrule complete and fixed.

S&F 15mm Stop valves, fency type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for uniuns and fixed

S&F Rotational moulded polythene water storage tank (cylendrical or vertical top) hoisted and fixed in position all as specified in SSR Part-I, capacity 500 ltrs.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete.

M&L for form work to edges of concrete flats, treads breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs n.exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal of sloping and similar work exc 10cm but n.exc 20cm wide for rough finished surface of concrete.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; verticle or to batter for rough finished surfaces of concrete flat.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paints.

M&L for preparation of newly plastered surfaces and applying three coats of whitewash on ceiling.

M&L for preparation of newly wooden surfaces and applying two coats of synthetic enamel paint over a coat of primer.

S&F pillar taps fency type 15mm bore size, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

S & F in repairs aluminium anodised tubular towel rail, 20mm dia ‘D’ type, 60CM long between flanges, fixed in repair.

M&L PVC(SWR)I floor trap plain with gratings including jointing to waste pipes with solvent cement size 75mm bore complete all as specified or as directed by Engineer-in-Charge.

S&F in vitreous china urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, granting and union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waster pipe)

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in trenches or in floor 110mm bore

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints,laid in trenches or in floor 75mm bore

PVC bend any radius size 110mm bore with access door

PVC bend any radiius size 75mm bore with access door

Removing of hard soil excavated material n.exc 50m and depositing where directed at a level n.exc 1.50m above the starting point and complete.

Returnig, filling in, incl spreading, leveling watering and well ramming in layers not exc 25 cm thick above or below ground level complete all as specified and as directed

Providing cement concrete type C-1, 1:3:6 ( using 20mm graded stone aggregate), 75 mm thick as in plinth protection laid in bays not exceeding 2 Sqm each and finishing even and fair on top without using extra cement with 6mm wide joints throughout the thickness of plinth protection in concrete bays.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm thick (below or above ground level); thrown away from the site ,complete all as specified and as directed.

PCC 1:3:6 Type C2 using 40mm graded crushed stone aggregate as in foundations , filling and mass concrete all as specified.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc.

M&L for 15mm thick cement plaster with water proofing compound in cement mortar 1:4 on brick or concrete surfaces including finishing surfaces even and smooth using extra cement. Note : WPC shall be measured and paid under respective item.

Supply only liquid water proofing admixture.

Constr of soakage well (1.80 mtr dia x 3.00 mtr deep) incl excavation in any type of soil, foundation in PCC 1:3:6 type C2,(using 40mm graded crushed stone aggregate),walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of brick masonry in CM,RCC cover slab in M25 /SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size

Constr of RCC hume pipe septic tank designed to carry sewage and sullage water,excavation in any type of soil,PCC 1:4:8 below foundation, Vent shaft,connection etc,complete, all as directed by Engr-in-charge.

Plain cement concrete (1:3:6) type C2 (using 40mm graded crushed stone aggregate) as in bed to drain pipes incl packing under and hauching against the side of pipes after they are laid and tested for 150mm bore Reinforced concrete (class NP2) pipes complete Note-(i) Thickness of concrete bed shall be 100mm.

S&F 150mm bore Reinforced concrete pipes, (class NP2) laid and jointed complete with collars in trenches and all as specified and directed by Engr-in- Charge.

M&L Cement conrete type C2 1:3:6 40mm graded aggregate in surface channels and drains complete all as specified and directed by Engr-in-charge

M&L, providing precast reinforced cement concrete cover slab for manhole/drain cover with plain faces set in cement mortar 1:6, type C1 1:3:6(using 20mm gradedaggregate), complete all as specified and directed by Engr-in-charge

S&F PVC (SWR) pipes, Single socketed, in any length, with rubber rings 110mm dia, vent cowl as specified ad as directed.

Supply, laying,fixing, passing through pipe or laid in trenches and testing underground XLPE insulated heavy duty electric cable with aluminium conductor 1100 volts grade cross section area 10 sqmm 2 core complete all as specified and directed.

Sand cushioning for under ground cable 8 cm before laying the cable and 15 cm after laying and streching the cable complete all as specified and directed by Engineer-in-Charge.

M&L Un-reinforced precast factory made concreate cable covers, class LV type-I, with flat size 250x150x40 mm Complete all as specified and directed.

Material and labour for point wiring with 1.5 sq mm PVC insulated unsheathed single core stranded copper conductor FRLSH cable 1100 Volts grade, drawn through and including 20 mm size PVC surface casing and capping , medium grade along with 1.5 sq mm continuous PVC insulated unsheathed stranded copper conductor FRLSH cable for earth continuity wire, connected to earth dolly and to be terminated in pressed steel sunken boxes (having wall thickness not less than 1.22 mm for boxes upto a size of 200 mm x 300 mm and beyond that the wall thickness shall be not less than 1.63 mm), concealed type, covered with 3.0 mm thick bakelite sheet for mounting switches, sockets, fan regulators etc including testing on completion complete all as specified and as directed by the Engineer-in-Charge for one light point/Fan point/bell point controlled by one switch complete all as specified and directed.

All as per item No 77 above but for one three / five pin switch-socket outlet, 5 Amps on the same board all as specified and as directed

All as per item No 77 here in before but one 3 pin socket out let 5 Amps on independent board.

All as per item No 77 here-in-before but for one 15 Amp 6 pin switch socket outlet, independent, with 4 sq mm single core stranded copper conductor along with 4 sq mm continuous PVC insulated unsheathed stranded copper conductor cable for earth continuity wire, all as specified and as directed by the Engineer-in-Charge.

S&F in replacement switch socket combination 5 pin, 5 Amps 2 in 1 flush type (multipurpose) suitable for 2 pin / 3 pin pulg. Complete all as specified and directed by Engineer-in-Chage.

S&F in replacement switch socket combination 5 pin, 16 Amps 2 in 1 flush type (multipurpose) suitable for 2 pin/3 pin plug complete all as specified and directed by Engineer-in-Chage.

S&F in replacement switch piano flush type single pole one way 5 Amps. Complete all as specified and directed by Engineer-in-Charge.

S&F in replacement ceiling rose surface bakelite 65x50mm two to three therminal conforming to ISI. Complete all as specified ans as directed by Engineer-in-Charge.

Supply and fixing only lamp holder, PVC/ polycarbonate type with back plate straight or angular suitable for batten fitting, complete all as specified and directed.

Supply and fixing surface and wall mpounted LED batten with ppolycarbonate housing and intergrated electronic driver tube light fitting 20W 4 ft long 220V and connecting to ceiling rose with three core twisted flexible copper cable of suitable size complete all as specified and directed

Supply only LED 7 W Ball Lamp LED Lamps ( Dualite Series ) - B22 Base (6500K~3000K) all as specified and as directed. Make : SYSKA Model : SSK-PAG-7W-2 IN 1

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet 10 Watt 220Watt 220V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

Supply and fix exhaust fan 250mm sweep plastic type (Make : Havells Ventil Air DX or equivalent) all as specified and directed

Supply and fixing sheet metal enclosure for double door MCB DBs, phosphatised, powder coated, Single Pole & Neutral (SPN), suitable for 4 way, 240 volts, IP 43 & IK 09 fixed on wall with din rail, neutral and earth bar, in proper position all as directed by the Engineer-in-Charge. (Make: Legrand Cat No : 6077 11 or equivalent L&T/ ABB).

Supply and fixing MCB Single Pole (SP) of capacity 6 Amps to 32 Amps, 240 V AC, breaking capacity 10 KA, C series, fixed in proper position complete all as directed by the Engineer-in-Charge. Make : Legrand cat no 408587 or equivalent model of make L&T, ABB

Supply and fixing MCB Single Pole and Neutral (SPN) of capacity 32 Amps, 240 V AC, breaking capacity 10 KA, C series, fixed in proper position complete all as directed by the Engineer-in-Charge. Make : Legrand cat no 408518 or equivalent model of make L&T, ABB

Supply and fixing Single pole and neutral enclosure with a two pin and earth plug and socket complete with one double pole MCB 20 Amps

M & L for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanized steel earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work in soft loose soil, P.C.C pit with (1:3:6) type C-I, with 50 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab (reinforced with 8 mm dia TMT bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, complete in all respect, GI earth wire protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion complete all as specified and as directed by the Engineer-in-Charge.

Deduct Schedule of Credit of Rs (-) NIL (Minus) as listed in Schedule 'A' Part-II. Contract Sum shall be arrived after deducting the credit amount. Note :- Tenderers will not quote against this item being a firm amount.

M/S SONAM RIGZIN

M/S SONAM angchok