CERTAIN BR AND EM MAINTENANCE WORKS AT REASI KALAKOTE SAMOTE BUDHAL MAHORE ADBAS SARH AND GOOL UNDER AGE REASI OF GE NAGROTA

Amount

Demolition of brick work or stone/ boulder Masonry, built in cement mortar including all quoins, pillars etc. complete all as spd & directed.

Material & Labour Brick work with sub class 'B' bricks built in CM 1:6 straight or curved on plan exc 6 m mean radius complete all as spd & directed..

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. complete all as spd & directed.

M & L for Rendering 10 mm thick on other than fair faces of walls of brick work or concrete surfaces in cement mortar 1:6 compound finished even and smooth without using extra cement complete all as specified and as directed.

M&L for Rendering 15mm thick in two layers [base layer 10mm in CM 1:4 & finishing layer 5mm thick in cement mortar (1:4)] using water proofing compound in 2nd layer only on brick work or concrete surfaces of wall, surfaces finished even and smooth using extra cement complete all as specified & directed. Note : WPC shall be measured and paid separately

Supply only liquid water proofing compound complete all as specified and directed.

Material & Labour Preparation of newly plastered wall surfaces and applying two coats of distemper oil emulsion over one coat of 2 to 3mm thick white putty 1mm thick preparatory to distempering complete all as specified and directed.

Material & Labour for priming new surface of wall with alkal iresistant priming paint of and applying two coats of cement base paint complete all as specified and directed.

Taking down Chowkats or frames n. exceeding 1.5 Sqm each (Without taking off shutters from the frame). complete all as spd & directed.

Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4.00 Sqm each (Without taking off shutters from the frame). complete all as spd & directed.

Taking down Shutter exceeding 1.0 Sqm but not exceeding 2.00 Sqm each. complete all as spd & directed.

Taking down Shutter exceeding 2.0 Sqm each. complete all as spd & directed.

Supply & Fix Pressed steel frames factory made for doors out of 1.25mm thick PBI sheet with one of more rebates including necessary flat iron lugs,hinges, lock strike plate, hinges etc complete, size of frame 125x60mm including tarring ends and back of chowkats and lugs including back filling of PCC 1:3:6 for chowkats & PCC 1:2:4 for block for hold fast including two coats of synthetic enamel paint over a coat of red oxide primer on exposed surfaces all as specified and directed.

Supply & Fix 35 mm thick 2nd class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply & Fix 35mm thick, 2nd class hard wood glazed and skelton shutter, open rebated and prepare to receive glass, gauzed etc(without sash bars) edges of framming plain , chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR PART I Section 8 clause 8.24(a) supplied and fitted to chowkhat complete all as specified and directed.

Supply & Fix 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commerial type of one side and another face is covered with aluminium sheet, 0.5mm thick, fixed with aluminium alloys screws complete all as specified and directed.

Material & Labour preparation of new wooden surfaces over10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer complete all as specified and directed.

Supply & Fix Steel windows/ventilator with tubular frame factory made with double shutter (wire gauged shutter & glass/glazed shutter, (wire cloth and glass panes shall be measured and paid separately) of size 79mmx39mm,16 gauge rectangular tubular frame with side hung shutter with glazing bars 12x3mm flat iron incl box type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100mm long and 10mm square bar grills complete, two coats of synthetic enamel paint over one coat of red oxide primer including taking down old windows/ventilators all as specified & as shown on drg .CEUZ/TD/1269/2008 SHT 1/1 to 1/3.

Supply and Fix Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as perspecification & drawing complete all as specified and directed

Supply and Fix Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2,4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing including all fittings complete all as specified and directed

Supply & Fix Floor door stopper of aluminium alloy body and tongue,anodised, with hard drawn steel spring, fixed in floor Door Stopper 140 mm complete all as specified and directed

Supply & Fix Galvanised mild steel wire cloth,0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed

Supply & Fix Aluminium anodised handle extruded section of size 150mm complete all as specified and directed.

Supply & Fix Aluminium anodised handle extruded section of size 125mm complete all as specified and directed.

Supply & Fix 100 mm butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as specified and directed.

Supply & Fix Aluminium alloy, anodised, sliding door bolt of length 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of sections or cast-aluminium extruded alloy and fixed complete all as specified and directed.

Supply & Fix Aluminium anodised barrel tower bolts extruded section of size 200 mm, all as specified and directed.

Supply & Fix Aluminium anodised barrel tower bolts extruded section of size150 mm, all as complete all as specified and directed

Supply & Fix 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed

Supply only Galvanised mild steel wire cloth,0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as spd & directed.

Supply only MS Mortice lock, vertical type, 4 levers of size 75/65 mm complete all as spd & directed.

Supply & Fix Powder coated Anodised aluminium frame(Thickness of powder coating not less than 50 micron) for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed

Supply & Fix Powder coated Anodised aluminium door shutters,aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, mortice lock,screws etc. complete all as specified

Supply & Fix Powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sectionsweighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1no.) complete all as specified complete all as specified and directed

Supply & Fix 5.5mm thick plain sheet glass as in window and door shutters with and including rubber gasket and natural colour anodized 15micron snap on aluminium beading/glazing, clips etc complete all as specified and directed.

Supply & Fix Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as spd and direcetd.

M & L for Hacking out old broken glass (any thickness, size, quality or description) from wooden/ steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads. complete all as specified and directed

Supply & Fix 3 mm thick figured glass pin headed quality and glazing with oil putty or fixed with bead/glazing pins in squares any size in each pane all as specified and directed.

Supply & Fix sheet glass ordinary quality 3 mm thick in squares and glazing with oil putty or fixed with bead/ glazing n exc 0.5 sqm each pane and glazing with complete all as specified and directed.

M & L for Securing glass of any description in existing glass in metal frames glazed with putty/ beads including removing loose or decayed putty/ beads, painting/oiling one coat on rebates, grooves, reputtying and painting/oiling puttied surface to match existing work (New length of frame reputtied shall be Measured )

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Demolition of floor concrete in ground floors and pavings n exc15 cm thickness (below or above ground level) complete all as specified and directed.

Material and Labour for Non - skid coloured eramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes complete all as specified and directed.

Material and Labour for Non - skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes complete all as specified and directed.

Material & Labour vitrified tiles double charged,10 mm thick ,area of each tile exc 0.36 Sqm but n.exc 0.42 sqm, in floor etc set and jointed in neat cement slurry including 15 mm screed bed in CM 1:4 complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B0 using 12.5mm graded stone agg as in levelling coarse under floor complete all as specified and directed.

Material & Labour Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including incl 10mm thick plaster in cm 1:4 complete all as specified and directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings. complete all as specified and directed.

Material & Labour Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Supply & Fix Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation board/slabs/blankets/AC boards etc any thickness . complete all as specified and directed.

Supply & Fix Anodised aluminium snap grid frame work for false ceiling all as specified. (Size of grid 605 X 605 mm) complete all as specified and directed.

Supply & Fix 6mm thick Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws.) fixed in ceiling surface complete all as specified and directed

Supply & Fix 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. complete all as specified and directed

Supply & Fix Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as spd and directed.

S & F in repairs 15mm Chromium plated fancy type Bib taps, cast copperalloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified

Supply only 15mm dia bib tap standard of PTMT any colour, high pressure screwed for iron pipeand fixed (minimum weight 90 gms) complete all as specified and directed

Supply & Fixed in repairs 15mm fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed

S & F in repairs cast aluminium (extruded section body) door closer by hydraulically regulated, designation No.3 univrsal type, suitable for door shutters up to 851mm to 1000 mm in width and of weight between 61 to 80 kg fixed complete alll as specified and directed.

Supply and fixing in replacement of following GI fittings of size 15mm bore pipe

Long bend

Socket

Elbow

Nipple upto 100 mm long

Reducer socket 15/20mm

Reducer socket 25/20mm

Reducer socket 25/15mm

Supply and fixing in replacement of following GI fittings of size 20 mm bore pipe

Long Bend

Socket

Elbow

Nipple 100 mm long

Nipple 150 mm long

Supply only 15 mm Stop/Angle Valves, fancy type, chromium platedcast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete alll as specified and directed.

S & F in repairs grating doom 125mm dia with waste hole of PTMT fixed on floor/nahani trap with cement mortar, fixed in repairs complete all as specified and directed. (Minimum weight 40 gms)

Supply & Fixed in repairs CP Brass shower rose 125mm of size with or with out swivel joints any size including fixing to steel pipe or union as fixed in repair complete all as specified and directed.

Supply & Fix PVC connections 15mm size 600 mm long as fixed in repairs complete all as specified and directed.

Supply & Fixed in repairs brass float valves high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed to iron pipe of bore 20mm complete all as specified and directed.

Supply & Fixed in repairs brass float valves high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule and fixed to iron pipe of bore 15mm complete all as specified and directed.

Dismantling water tanks and removing to store capacity exceeding 250 ltrs and not exceding 500 ltrs complete all as specified and directed.

Dismantling water tanks and removing to store capacity exceeding 500 ltrs and not exceding 1000 ltrs complete all as specified and directed.

Supply & Fix rotational moulded PVC water tank Triple layered (Cylindrical vertical with closed top) 1000 ltrs capacity hoisted and fixed in positoin all as specified in SSR part I complete alll as specified and directed.

Supply & Fix rotational moulded PVC water tank Triple layered (Cylindrical vertical with closed top) 500 ltrs capacity hoisted and fixed in positoin all as specified in SSR part I complete alll as specified and directed.

Supply & Fixed in repairs PVC body valve less syphonic action type flushing cistern white low level with inlet ball valve float and handle including brackets 10 lits capacity with 32mm dia PVC bend pipe for low level cistern complete all as specified and directed.

Supply & Fixed in repairs vitreous china pedestal pattern type white wash down water closet pan with Antimicrobial Solid Seat Cover but excluding flushing cistern and flush pipe complete all as specified and directed.

Supply & Fixed in repairs Vitreous China Squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rests complete all as specified and directed.

Supply & Fixed in repairs Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

Supply & Fixed in repairs PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/floor of 110 mm bore inclding dismantling of old U/S pipes complete all as specified and directed.

Supply & Fixed in repairs PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/floor of Bore 75 mm inclding dismantling of old U/S pipes complete all as specified and directed.

Supply & Fixed PVC (SWR) bends 75 mm dia radius complete all as specified and directed.

Supply & Fixed PVC (SWR) bends 110 mm dia radius complete all as specified and directed.

Supply & Fixed PVC (SWR) bends with access door of 75 mm dia radius complete all as specified and directed.

Supply & Fixed in repairs PVC (SWR) bends with access door of 110 mm dia radius complete all as specified and directed.

S & F PVC (SWR) junction single(single T) equal or unequal bore of pipe 75 mm bore complete all as specified and directed.

S & F PVC (SWR) junction single(single T) equal or unequal with access door bore of pipe 110mm bore complete all as specified and directed.

Supply & Fixed in repairs PVC (SWR) vent cowl 110 mm dia complete all as specified and directed.

Supply and Fix in 32mm dia waste coupling of PTMT (minimum weight 45 gms) with PVC waste pipe for WHB/urinal 750mm long complete all as specified and directed.

Supply and Fix in 40/50mm Sink waste coupling of PTMT with PVC waste pipe for Sink 750mm long complete all as specified and directed.

S&F in repair vitreous china wash basin with pedastal, white flat back size 550x400mm excluding chain and plug and porcelain stopper but including brackets, including 32mm bore CP based fittings and PVC waste pipe suitable for 32mm bore complete all as specified & directed

Taking up or down 15 mm bore steel tubing and connections, including cleaning for Refixing or removal to store. complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for Refixing or removal to store complete all as specified and directed.

S& F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors. complete all as specified and directed.

Supply & Fix 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed

Supply and fix of Brass chromium plated 15mm wall mixer valve 3-in-1 for mixing hot and cold water, fancy type complete alll as specified and directed.

Supply and Fix in repairs Health faucet (Hand shower) with 1metre flexible tube with wall hook, Chromium Plated complete alll as specified and directed.

S & F plastic water closet seat cover, white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device of make fixed with CI brackets fixed in repairs complete all as specified and directed.

Taking down cement plaster on brick wall including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M & L for Rendering 10mm thick on fair faces of brick work in cement mortar 1:6 finishing even and smooth without using extra cement upto any height, work to be carried out in patches complete all as specified and directed.

M & L for Rendering 15mm thick on fair faces of brick surface in cement mortar 1:4 finished even and smooth without using extra cement, upto any height from GL, work to be carried out in patches complete all as specified and directed.

M & L for Rendering 10mm thick in CM 1:3 as in ceilings or concrete surfaces such as chajjas, upward facia, downward facias and similar items finished even and smooth including dubbing coat without using extra cement complete all as specified and directed.

M & L for Preparation of newly plastered surfaces of ceilling,upward facias etc and applying three coats of white wash complete all as specified and directed.

M &L for 3mm thick wall care putty on wall complete all as specified and directed.

M & L for Preparation of newly plastered surfaces of wall and applying two coats of Oil bound distemper over one coat of primer complete all as specified and directed.

M&L for preparing the external newly Plastered surfaces of walls and applying two coat of Cement base paint over one coat of chalk whiting complete all as specified and directed.

M&L for Preparation of old decorated surface of wall including brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil, greasy spots and applying One coat of Oil Bound Distemper on wall complete all as specified and directed.

M&L for Preparation of old decorated surface of wall including brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil, greasy spots and applying two coat of Oil Bound Distemper on wall complete all as specified and directed.

M&L for Preparation of old decorated surface including brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil, greasy spots and applying two coat of cement base paint on wall complete all as specified and directed.

M&L for Preparation of old decorated surface including brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts, trading oil, greasy spots and applying one coat of cement base paint on wall complete all as specified and directed.

M&L for Complete removal of existing treatment and applying two coat of apex exterior quality over a coat of primer complete all as specified and directed.

M&L for Preparing Old steel painted surface to receive painting, including washing and cleaning, etc. over 10cm in width or girth, not otherwise described & applying one coats of synthetic enamel paint in any pattern complete all as specified and directed by Engineer in charge.

M&L for Preparing Old wood and wood based surface to receive painting, including washing and cleaning, etc. over 10cm in width or girth, not otherwise described & applying one coat of synthetic enamel paint complete all as specified and directed.

Supply & Fix in 32mm dia PVC waste pipe for WHB/urinal 750mm long complete all as specified and directed.

Supply Fix 50/63mm dia PVC waste pipe suitable for sinks 750mm long complete all as specified and directed.

Supply & Fix 75mm diaPVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and as directed by the Engineer-in-Charge.

S&F Vitreous China Urinal bowl type or half stall pattern , white including flush pipe and waste pipe) including CP Spreader and other accessories and Bracket with fixing arrangement complete all as directed by the Eng-in-Charge

S&F urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (Minimum weight 60 gms ) complete all as directed by the Eng-in-Charge

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as directed by the Eng-in-Charge

Supply & fix in Shelf of PTMT fixed with including chromium plated brass screw and wooden/plastic cleats (Minimum weight 300 gms ) complete all as directed by the Eng-in-Charge

M& L for aluminium dividing strips width 28mm and , 1.5mm thick as in door stopper inserted in position conform to design complete all as directed by the Eng-in-Charge

Supply & Fix fancy type stainless steel Drapery rods 19/20 mm bore for curtain rails with fixing stainless steel brackets, fency stainless steel stops and curtain rings (06 Nos per mtr) complete all as specified and directed .

M& L for Cleaning of sewage lines which are blocked /filled with sludge, semi solid/ material etc by roding manholes to manholes manually or by sewage cleaning machine without causing any damage to sewage line / manholes manholes covers taking out and refixing the covers and removing the sludge to a non inhabitant area or buried into ground all as specified for the 150mm internal dia of pipe complete alll as specified and directed.

M& L for Cleaning of sewage lines which are blocked /filled with sludge, semi solid/ material etc by roding manholes to manholes manually or by sewage cleaning machine without causing any damage to sewage line / manholes manholes covers taking out and refixing the covers and removing the sludge to a non inhabitant area or buried into ground all as specified for the 100mm internal dia of pipe complete alll as specified and directed.

M& L for Cleaning of septic tanks, soakage well of any capacity and manholes by Desludging / dewatering including inlet/ outlet chambers, removing out all scum, silt, residuals sludge (both organic and inorganic nature) after plugging the incoming sewage lines through combined high pressure water jetting cum suction (Vacuum) type machine mounted on LCV/HCV facility of high pressure vacuum and removing the same in the tank to a place outside cantonment at the place meant for the purpose by local municipality,complete alll as specified and directed.

M& L for Cleaning of blockage of any type of wc (Indian/pedestal) from WC pan to Ist manhole in single storied bldg including resetting/ refitting of asccess door in soil pipe where opened without causing any damage to the wc pan 'P' or 'S' trap and pipe including fitting complete all as speciffied

M& L for Cleaning of blockage of any type in Nahani trap provided in bath room, kitchen and indoor waste water pipe of kitchen sinks and WHB and removing all the sludge and foreign material from the trap and waste pipe from blocked trap to gully trap/ surface drain wherever opened or without causing any damage to the trap and pipe complete all as speciffied and directed

M& L for Cleaning of service RCC/Ferro/PVC service/over head tank cleaning process as under (a) Dewatering using submerssible pump/bailing out of water to dispose the minimum level of dirty water from the tank. (b) Cleaning the tank/ UG sump bottom, walls and ceiling using high pressure water jet to dislodge the algae calcinations, dirt etc. (c) Disposing the dirt water sludge etc., using specially designed sludge removal pump. (d) Cleaning the tank inside throughly by using industrial grade vaccum pump to make the tank inside free from dirt, algea and sludge etc. (e) Treating the inside walls, bottom, ceiling of tank including all nooks and corners by using and spraying anti bacterial agent such as hydrogenperoxide (bio degradable) for disinfection of tank inside. (f) Total disinfection and sterlisation of tank hyginecally cleaned and bacteria free and safeby Eco-Friendly for storage of water. Note :- Incl cleaning of outlet pipe upto stop cock/gate valve by removing and refixing the same and making the line serviceable after cleaning & Qty of tank are consider for cleaning twice in a Year and Date of cleaning to be written over head tank after cleaning.

Exc. 250 ltrs and not exc 500 ltrs capacity

Exc. 501 ltrs and not exc 1000 ltrs capacity

Exc. 1001 lt and not exc 2000 lt capacty

Exc. 2001 lt and not exc 5000 lt capacty

S&L in repair 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as speciffied and directed

Excavation in trenches in soft/ loose soil exc 1.5 m deep and getting out including forming bottom to required level or slop for laying pipe, concrete bed manhole etc n.exc 10 Sqm on plan complete all as speciffied and directed(pipe and concrete bed shall be measured and paid separately )

Returning filling in soft/ loose soil including spreading levelling ,watering and well ramming in layers not exc 25 mm thick complete all as speciffied and directed

Removing of excavated surplas materials to a distance exc 50 m but nexc 100 mm and depositing where directed a level n.exc 1.5 mtrs above the starting point complete all as speciffied and directed

Demolition or breaking up 150 mm dia drain pipe including fittings of any desciption in any position and removing rubbish upto a distance of n. exc 50 mtr complete all as speciffied and directed

M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested in cement concrete 1:3:6 type C-2 for 150 mm bore of pipe complete all as speciffied and directed

M&L Reinforced concrete pipes, class NP3, laid and jointed complete with collars 150 mm bore laid in trenches and jointed with CM 1:1complete all as speciffied and directed

M&L for brick work built in CM 1:4 with sub class 'B' bricks straight or curved on plan exc 6 m mean radius complete all as speciffied and directed

M&L rendering 15 mm thick on other than fair faces of brick surfaces or concrete surfaces and finished surfaces even & fair in CM 1:6 complete all as speciffied and directed

Demolition of reinforced cement concrete as in cover slabs of any description, removal of debris to beyond MD land as directed complete all as speciffied and directed

M&L for precast RCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in manhole cover slab with plain fair faces and set in CM 1:4 complete all as speciffied and directed

M&L TMT mild steel bars 6 mm to 8 mm dia cut to length, bent to shape required, including cracking, bending,spirally for hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as speciffied and directed

All as per item no.137 above but 10 mm dia MS round bar as in handle complete all as speciffied and directed

M& L Excavating in post holes (or similar holes)in hard dense soil each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm all as specified and as directed

M&L PCC 1:4:8 Type D2( using 40mm graded crushed stone agg) , as in fdn filling and mass concrete. complete all as speciffied and directed

S& F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165, including two coats of synthetic enamel paint over a coat of red oxide primer on exposed surfaces all as specified and directed.

SCHEDULE-A PART-II (E/M WORKS) Taking down carefully surface aluminium or copper point wiring with PVC casing-caping or conduit (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, regulators, sockets, light fittings etc and making good disturbed surfaces complete all as speciffied and directed

M&L for Concealed Point wiring using FRLSH PVC insulated unsheathed multi strand copper conductor cable 1100 volt garde 1.5 sqmm including 1.5 Sqmm FRLSH PVC insulated unsheathed multi strand copper conductor earth wire drawn in and including PVC conduit medium grade ISI marked not less than 20 mm dia concealed in wall & surface on ceiling with all conduit fittings etc terminated in and incl concealed sunken box readily available for fixing switches , sockets , fan regulators etc incl testing and making good to disturbed surface to match existing surface for modular type one light/fan/bell point complete all as specified and directed.( Sunken Box & cover plate shall be measured & paid for seperately)

All as per item no 143 but One socket outlet 6 amp controlled by one switch on the same board with other switches complete all as speciffied and directed .

All as per item no 143 One socket outlet 6 amp controlled by one switch on indepdendent board complete all as speciffied and directed .

M&L for point wiring in repair with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including PVC casing-caping not less than 32x16 mm ISI marked ivory colour with all conduit fittings / fixing accessories and unwelded sunken galvanized pressed steel terminal boxes of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets for one 16 amp socket outlet point controlled by one switch on independent board. complete all as speciffied and directed

S&F angle holder,in repair insulated polycabonate body with back plate complete all as speciffied and directed

S&F in switch piano flush button single pole one way 6 amp complete all as speciffied and directed

S&F in switch piano flush button single pole one way 16 amp complete all as speciffied and directed

S&F in socket outlet 2 in 1, 3 pin 6 & 16 amp flush type complete all as speciffied and directed

S&F in socket outlet 2 in 1, 2 & 3 pin, 6 amp, flush type complete all as speciffied and directed

S&F in Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp flush type universal omplete all as speciffied and directed

S&F in Switch socket combination 2 in 1, 3 pin, 5 Amp flush type universal complete all as speciffied and directed

S&F in Plug Top of socket outlet 6 amp complete all as speciffied and directed

S&F in Plug Top of socket outlet 16 amp complete all as speciffied and directed

S&F in Switch socket combination 2 in 1, 3 pin, 5 and 15 Amp box type complete universal complete all as speciffied and directed

S&F in Switch socket combination 2 in 1, 3 pin, 5 Amp box type complete universal complete all as speciffied and directed

S & F in Modular switch 5/6 Amps suitable for 1 Module complete all as speciffied and directed

S & F in Modular socket 5 pin 5/6 Amps suitable for 2 Module complete all as speciffied and directed

S & F in Modular switch 15/16 Amps suitable for 1 Module complete all as speciffied and directed

S & F in Modular socket 5/6 pin 15/16 Amps suitable for 2 Module complete all as speciffied and directed

S & F in Modular Fan step Regulator electronic, 120 watts 2 Module complete all as speciffied and directed

S&F in ceiling rose 3 plates polycarbonate body complete all as speciffied and directed

S&Fin hum free electronic step fan regulator 120 - 280 volts of 100 watt capacity (socket type) including connecting up complete all as speciffied and directed

S&F in bell push, flush type, 6 amp 240 volts complete all as speciffied and directed

S&F in door bell, AC, 240 volts, single pole complete all as speciffied and directed

M&L in replacement of sub main wiring with two single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 4Sq mm drawing through and including concealed rigid non metallic PVC conduit medium grade ISI marked minimum 20 mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 4sq mm as earth continuity conductor connected to commen earth and earth dolly complete all as specified and directed

M&L in replacement of sub main wiring with two single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6 Sq mm drawing through and including concealed rigid non metallic PVC conduit medium grade ISI marked minimum 25 mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6 sq mm as earth continuity conductor connected to commen earth and earth dolly complete all as specified and directed

M&L in repair for earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including 15 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work complete all as speciffied and directed

S&F in repair MCB distribution board, powder coated, CRCA steel sheet, degree of protection IP 43 - IK 09 with reversible double door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required with following ratings & ways:-

SPN, 240 volts, 4 ways.

SPN, 240 volts, 8 ways.

SPN, in repair 240 volts, 12 ways.

TPN, 415 volts, 4 ways.

S&F in repair MCBs of 'C' series having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs of following ratings:-

Single pole 6 to 32 amp.

Single pole 40 to 63 amp.

Double pole 10 to 32 amp.

Double pole, 40 to 63 amp.

Four pole 40 to 63 amp.

S&F in repair LED tube light batten (1.2 m) made of CRCA sheet housing with a PC glossy difusser and mounting accessories duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficacy of 105 lumens per watt and total power consumption not more than 22 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD < 10% and PF > 0.95 complete all as speciffied and directed

All as pr Item No 172 here in before but for LED tube light batten warm type (Yellow Lumen) complete all as speciffied and directed

S&F in repair LED tube light batten (2 Fit ) made of CRCA sheet housing with a PC glossy difusser and mounting accessories duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficacy of 105 lumens per watt and total power consumption not more than 10 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD < 10% and PF > 0.95 complete all as speciffied and directed

S&F in repair LED (bulb) 18 watt including connection complete all as speciffied and directed

S&F in repair LED (bulb) 12 watt including connection complete all as speciffied and directed

S&F in repair LED (bulb) 10/9 watt including connection complete all as speciffied and directed

S&F in repair LED bulkhead fitting 9 watt IP 66 & IK 09 with pressure diecast aluminum housing & polycarbonate diffuser duly prewired connection with 0.75 sqmm PVC insulated & sheathed three core flexible multi stranded copper conductor cable complete all as speciffied and directed

S&F in repair energy efficient recessed mounted LED luminaire suitable for 2'x2' , 36 watt 230 V 50 Hz, grid ceiling with flat diffuser and lumen output of 3300 lumens having constant current electronic driver duly connected with 0.5 sqmm white colour PVC insulated & sheathed three core flexible multi stranded copper conductor cable in renewal of any type luminaire as required complete all as speciffied and directed

All as pr Item No 179 here in before but for LED luminaire warm type (Yellow Lumen) complete all as speciffied and directed

Dismantaling /Opening of upper portion of Diesel Engine 62.5 KVA (Make : Greaves/ Kirloskar/ Cummins or any other make) air cooled,turbo charged ,Vertical type for top over hauling, repair/ servicing of engine including taking out rediator /fuel pump,water Pump,Turbo charger etc (Egnine oil and coolent reaquired for this job is deemed to be included in the quoted rate. (a) Dismantaling/Opening of complete cyllinder head assebly rockers arms assemblypiston head assembly ,sleeves byremoving nuts &bolts for repair complete. (b) Servicing & washing of complete engine partswith kerosine oil ( c) Re- assembling of engine after replacementof UNSV/defective parts with new parts as listed in given below per job shall be deemed to be included in this rates and testing of engineas per company recommendation after reassembling all parts as directed to the satifaction of the Engr-in -Charge Note : Repair and Transportation (BY JCB / HYDRA OR ANY OTHER MEANS) charge for carrying out repair & reinstall on same installation back shall be deemed to be included in this rates

Supply inreplacement of following parts given below rates shall be deemed to be above job included .

Valve Exhaust

Valve inlet

Insert Valve Seat

Guide Valve

Cup Injector

Fip Element

Gasket Set

Hose Pipe

Fuel Filter

Lubrication Oil Filter

Super By Pass Fillter

Hose Clip Set

Piston set Complete

Ring Set Complete

Cyllinder Linner

Connecting Rod Bearing

Gasket Set Cyllinder Head

Callibration of Fuel Pump

Head Repair Work

Callibration of injectors of Nozzels

Lubrication Oil Pump

O ' Ring Set Complete

Set of Fuel Flexible Pipe

Stem Seal

Dismantaling /Opening of upper portion of Disel Engine 30 KVA (Make : Greaves/ Kirloskar/ Cumiuns or any other make) air cooled,turbo charged ,Vertical type for top over hauling, repair/ servicing of engine including taking out rediator /fuel pump,water Pump,Turbo charger etc (Egnine oil and coolent reaquired for this job is deemed to be included in the quoted rate. (a) Dismantaling/Opening of complete cyllinder head assebly rockers arms assemblypiston head assembly ,sleeves byremoving nuts &bolts for repair complete. (b) Servicing & washing of complete engine partswith kerosine oil ( c) Re- assembling of engine after replacementof UNSV/defective parts with new parts as listed in given below Per job shall be deemed to be included in this rates and testing of engineas per company recommendation after reassembling all parts as directed to the satifaction of the Engr-in -Charge Note : Repair and Transportation (BY JCB / HYDRA OR ANY OTHER MEANS) charge for carrying out repair & reinstall on same installation back shall be deemed to be included in this rates

Supply inreplacement of following parts given below rates rates shall be deemed to be above job included .

Valve Exhaust

Valve inlet

Insert Valve Seat

Guide Valve

Cup Injector

Fip Element

Gasket Set

Hose Pipe

Fuel Filter

Lubrication Oil Filter

Super By Pass Fillter

Hose Clip Set

Piston set Complete

Ring Set Complete

Cyllinder Linner

Connecting Rod Bearing

Gasket Set Cyllinder Head

Callibration of Fuel Pump

Head Repair Work

Callibration of injectors of Nozzels

Lubrication Oil Pump

O ' Ring Set Complete

Set of Fuel Flexible Pipe

Stem Seal

M & L for Servicing of DG Sets of capacity 62.5 KVA of make (Make : Greaves/ Kirloskar/ Cummins or any other make) by the authorised Engineer of respective manufacturer of DG Set continous operational condition including the following checkings all as specified and directed by Engr-in -charge (Egnine oil and coolent reaquired for this job is deemed to be included in the quoted rate. (i) Removing the existing engine oil, clean the oil sump and refilling with required quantity of new engine oil 20W40 & coolant upto top. (ii) Checking of fan motor hub (iii) Checking exhaust and inlet manifold belt and cap screw (iv)Cleaning of radiator inside and out side thoroughly with solution (caustic soda) to the entire satisfaction of Eng-in-charge by removing and re-fixing in original position after cleaning. (v) Checking and adjusting injector and valves, tappet and replace the gasket including cost of gasket. (vi) Cleaning fuel inlet connections and screw, (vii) Checking of vibration damper and rectified. (viii) Servicing of turbocharger by checking, leakage tightening of mounting screws & nuts and replace oil. (ix) Checking water temperature safety control (x) Checking and correcting up impeller of water pump for excess play. (xi) Servicing of governer and Changing of governor oil. (xii) Checking and adjusting all fan belt. (xiii) Any other check as per manufacturer`s instructions Note:- Necessary spare parts required if any will be measured and paid under relevant items

S & F in repairs Kit, fuel filter and ring complete all as specified & directed.

S & F in repairs Element for Lubrication oil filter. complete all as specified & directed.

S & F in repairs Kit, Element of super bypass filter complete all as specified & directed..

S & F in repairs Seal, O Ring and Air cleaner. complete all as specified & directed.

S & F in repairs Kit Conversion complete all as specified & directed.

S & F in repairs Gasket, Rocker lever cover b complete all as specified & directed.

All as per item no.185 above but DG Sets of Capacity 30 KVA DG set complete all as specified & directed.

S & F in repairs Kit, fuel filter and ring complete all as specified & directed.

S & F in repairs Element for Lubrication oil filter. complete all as specified & directed.

S & F in repairs Kit, Element of super bypass filter complete all as specified & directed..

S & F in repairs Kit Conversion complete all as specified & directed.

S & F in repairs Gasket, Rocker lever cover complete all as specified & directed.

M&L for Rewinding of armature of Dynamo/alternators 12V/24V volts with `F' class copper wire to match existing gauge including dismantling of old coil , cleaning thoroughly winding with super enameled copper wire of existing size and gauge,varnishing, drying etc and fixed with dynamo/alternator properly tesing and commissioning complete all as specified & directed.

S & F repair radiator hoses of size 40mm dia or as per existing dia and 60 cm length for any capacity of DG set including jublee clip, clamp nuts etc are properly fixed and connected. complete all as specified & directed to the satifaction of the Engr-in -Charge

S & F in replacement of flexible pressure pipe for lubricant size of 60 cm length for oil and fuel connection for complete suitable for 40/62.5/82.5 KVA Engineas complete all as specified & directed. the satifaction of the Engr-in -Charge

Supply only Engine oil 20W/40f make (Castroll/Kirloskar/HP) complete all as specified & directed.

Supply only distilled water packed in sealed gallan of 5 Ltrs complete all as specified & directed.

Supply Only water coolant(diluted)in radiator (make volve line or equivalent) including removal of old water/coolant, complete all as specified & directed.

Dismantling and removing of water pump assembly of any capacity any type of DG Set complete from the engine,repair/overhauling the same by replacing tornout components like bearing,impeller,bushes, oil seal,water seal,gaskets etc. reassembling,refixing and testing complete all as specified & directed. to the satifaction of the Engr-in -Charge

Repair/overhauling of self starter 12V/24V including replacement of worn out clutch assembly,bush,spring,plunger assembly, solenoid switch,carbon brushes,brush spring etc. complete all as specified & directed. to the satifaction of the Engr-in -Charge for the 40/62.5/82.5 KVA DG Set

M & L for replacement of totally damaged self starter 12V/24V complete assembly suitable for any capacity of DG Set complete all as specified & directed.

Repair/overhauling of dynamo including replacement carbon, brushes holder, spring, commutator /slipring assembly bearing, regulator etc. of any make, type and capacity. complete all as specified & directed.

Supply in replacement of electrically operated fuel shut down valve assembly complete testing and commissioning as specified and directed by Engr.in-charge including dismantling and removal of old U/S valves of any capacity DG set. complete all as specified & directed.

Disconnecting and dismantling the alternator unit of 30 to 62.5 KVA DG Set from the base plate of the DG set and transporting to workshop for repair, dismantling the unit, further separating the armature from the startor carefully, cutting and taking out the burnt windings of the alternator carefully, cleaning the slots and , duly applying the insulation and assembling the stampings inserting in position in the startor including applying slot insulation and rewinding of the alternator startor winding with super enameled copper conductor of same gauge and same number of turns as that of existing one including replacement of carbon brushes tapping the windings and bringing out the coil conections for production of 3 phase 415 volt 50 HZ AC supply and preheating the windings and applying insulating varnish and drying the windings in oven and assembling the unit and transporting back to installation and fixing on base plate and coupling with the DG set and testing complete all as specified and directed.

Supply in replacement of diode assembly complete suitable to match the existing one of 62.5/40 KVA alternator excitor unit. complete all as specified & directed.

Supply in replacement of PVC insulated battery lead with 16 Sq.mm copper conductor cable of length 2 mtr with copper/brass clamps and lugs for fixing on battery terminals and self starter complete as specified and as directed.

Supply in replacement of rectifiers for alternators suitable for Gensets upto 40/62.5/82.5 KVA capacity complete as specified and as directed.

Supply in replacement of water temperature gauge complete with cable and accessories at the last range 0 to 150 degree centigrate complete as specified and as directed.

Supply in replacement of oil temp gauge as per existing site requirement complete as specified and as directed.

Supply in replacement of oil pressue gauge as per existing site requirement complete as specified and as directed.

Dismantling the defective Fuel Injector Assembly of any capacity from the existing foundation and engine including taking down all electrical connections transporting to approved authorised workshop, after setting up opening the complete, connector plate, gasket & complete overhauling re- assembling the Fuel Injector after transporting back to site re-installing carrying out alignment of complete DG set reconnecting up all electrical connections testing and commissioning complete the following capacity of DG set (Note:- (a) Rate quoted shall be deemed to be inclusive making good the distrubed surfaces (b) The DG set shall be tested for the satisfaction of Engr -in -charge to achive designed parameters.

62.5 KVA DG

30 KVA DG

Attending compliant and inspection/trouble shooting/repair the AMF panel of any rating 3 phase 415V 50Hz AC supply including checking the serviceability of individul components, cleaning / tightning of loose connections, identification of defective parts including replacement of minor parts like jumper conneting cables, connectors, lugs, fastners etc, complete as specified and as directed. Note : Defective parts / repair work to individual parts shall be measured and paid separately.

Supply and replacing the following spares including connecting into electric circuit, testing and commissioing.

Solonoid valve 24V of suitable for 62.5 KVA to 82.5 KVA complete all as specified & directed.

Solonoid valve 12/24V of suitable for 30 KVA to 40 KVA complete all as specified & directed.

Changer relay AC 230V suitable for DG set AMF panel of rating 30 KVA to 82.5 KVA complete all as specified & directed.

Changer relay DC 24V suitable for DG set AMF panel of rating 30 KVA to 82.5 KVA complete all as specified & directed.

Time relay AC 230V suitable for DG set AMF panel of rating 30 KVA to 82.5 KVA complete all as specified & directed.

Time relay DC 24V suitable for DG set AMF panel of rating 30 KVA to 82.5 KVA complete all as specified & directed.

Coil 230/430V +/- 5% AC 50Hz complete all as specified & directed.

Supply and fixing in replacement of Digital volt meter as per existing size complete all as specified and directed.

Supply and fixing in replacement of Digital Amp meter as per existing size complete all as specified and directed.

Supply and fixing in replacement of Digital Frequency meter as per existing size complete all as specified and directed.

Supply and fixing in replacement of indicator lamp assembly complete LED type suitable for the existing system supply voltage for the existing system supply voltage 230V / 440 V AC including taking down old lamp assembly complete all as specified & directed.

Supply and fixing in replacement of AVR unit of 62.5 KVA to 30 KVA for matching the existing AVR unit, complete all as specified and directed by Eng-in charge.

S & F in repair battery terminal brass superior quality suitable for 180 AH 12 Volts Battery complete all as specified & directed.

S&F free lead acid battery 12 volts 180 AH complete all as specified and as directed by Engr-In-Charge.

M&L for servicing/ cleaning of MS diesel tank of DG set 62.5/40/30 KVA by draining out the diesel from tank, cleaning the tank with soap water/ suitable solution and painting the external surface with one coat of synthetic enamel paint of existing colour including repalcement of drain valve, outlet pipe complete all as specified and as directed.

S&F in replacement, fan belt suitable for 40/30 KVA DG set complete all as specified and as directed.

S&F in replacement, fan belt suitable for 62.5 KVA DG set complete all as specified and as directed.

Dismantling/ taking down complete radiator assembly of DG set 62.5 KVA and transporation to market for repair by :- (i) Opening the radiator assembly with brazing/ welding for repair/ services. (ii) Cleaning of all water tube with diluted solution of HCL & cleaning with water preasure & removing the sludge and dust from inside the tank by flushing out. (iii) Repair of fins by soldring/ brazing. (iv) Repair of bottom brass water tank by soldring/ brazing. (v) Repair of radiator hose assembly. (vi) Fixing the complete radiator assembly to its orignal position and testing complete

Dismantling/ taking down complete radiator assembly of DG set 30 KVA and transporation to market for repair by :- (i) Opening the radiator assembly with brazing/ welding for repair/ services. (ii) Cleaning of all water tube with diluted solution of HCL & cleaning with water preasure & removing the sludge and dust from inside the tank by flushing out. (iii) Repair of fins by soldring/ brazing. (iv) Repair of bottom brass water tank by soldring/ brazing. (v) Repair of radiator hose assembly. (vi) Fixing the complete radiator assembly to its orignal position and testing complete

S&F in replacement of Change over switch off load type with enclosure, conforming IS 13947 part I & III 415V, 4 pole of rating 100 amps, including taking out unservicable one complete all as specified and directed by Engineer-in -Charge.

S&F in replacement of Change over switch off load type with enclosure, conforming IS 13947 part I & III 415V, 4 pole of rating 200 amps, including taking out unservicable one complete all as specified and directed by Engineer-in -Charge.

S&F MCCB four pole 125 Amps, 35 KA fixed thermal & fixed magnetic setting including 4 spreder link set of same make as that of MCCB for connection and lugs as required all as complete as specified and directed.

S&F MCCB four pole 63 Amps, 25 KA fixed thermal & fixed magnetic setting including 4 spreder link set of same make as that of MCCB for connection and lugs as required all as complete as specified and directed.

Attending compliant / servicing / repair the servo controlled voltage stabilizer of capacity 25 KVA to 200KVA single/3 phase, (having input voltage of 160V to 260V and out put voltage stabilized at 220+9% for single phase and 300 to 460V input (Approx) and out put voltage stabilized at 430+ 1% V for 3 phase) with balanced / unbalanced load including checking the serviceability of individul components, cleaning / tightning of loose connections, including replacement of minor parts like jumper conneting cables, connectors, lugs, fastners etc complete all as specified and directed.

Taking out/removing the defective barrier assembly/ dimmer coil from the volatage stabilizer by manually/using chain pully block, transporting to workshop, removing the burnt windings cleaning and rewinding, with existing size super enamelled copper wire, varnishing, heating and transporting to site for refixing for the following capacity of stabilizers. Note : Old burnt copper winding will be measured and issued to contractor under Sch of credit.

25 KVA single/3 phase

50KVA to 75KVA single/3 phase

M & L for Filtration of transformer oil of Voltage Stablizer oil type up to 150 KVA capacity installed at different sub stations/locations using filtration plant , dehydration and improving di-electric strength of the oil to withstand 40 KV for one minute including testing of oil as specified and directed. NOTE : Stablizer oil test kit shall be provided by the contractor at site for testing of oil.

Supply and Filling in with new transfor oil for Voltage stabilizer oil EHV grade low viscosity of approved make as per IS-335 of 1992 and die-electric strength 20 KV when tested at 1mm gap incl submission of certificate fro IS approved lab for desired value of die-electric strength complete all as specified.

M & L for Cleaning the internal surfaces of volage stabilizer to free from dust/sediments/rust, removing transformer oil (where ever exists) and refilling, refixing the barrier assembly including connecting all electric/electroni/mechanical components, testing and commissioing for the following sizes:

25KVA single/3 phase

50KVA to 75KVA single/3 phase

Disconnecting the input/output electri supply 3 phase and Neutral AC 50Hz/single phase conections, removing the top cover for taking out defective voltage stabilizer including disconnecting connected electri/electronic/mechanical components of the following capacity stabilizers for repair after repair refixing the same position complete etc all as specifiedand directed. Note : Defective parts/ repair work to individual mparts shall be measured and paid separately.

25 KVA single/3 phase

50KVA to 75KVA single/3 phase

Supply and fixing in repair following spares including removing of respective defective spares of servo controlled Voltage stabilizer single/3 phase having standard input/out put voltages.

Push button switch

Auto manual switch

DPDT switch

Micro switch

Panel phase indication lamp

Potential meter

High low indicator lamp

Voltmeter 0 to 500 Volts

Ampere meter 20 to 100Amps

Current transformer 5VA to 10VA class 0.5 of rating 30, 50, 60, 75, 100, 150, 200/5A

Electronic circuit card including Control drive transformer with wiring.

PCB Holder

Rotary switch 5A for 3 phase.

Servomotor for 25 KVA to 50 KVA Voltage stabilizer

Servo motor for 75 KVA Voltage stabilizer

Carbon brush

Carbon brush holder with spring

Drive assembly upto 25KVA per phase

Drive assembly 75 KVA per phase

Toggle switch single pole one way 5Amps

Motor gear pinion

Digital Control panel with circuit board for High/Low voltage cut suitable upto 50 KVA 3 phsae voltage stabilizer.

Digital Control panel with circuit board for High/Low voltage cut suitable for 75 KVA 3 phsae voltage stabilizer.

M & L for Dismantling from electric circuit cleaning to free from dust/rust/oil/grease etc preparation of external surfaces and spray painting with two coat of synthetic enamel paint of approved colour for Voltage Stabilizer and refixing the same with new thimble, washers etc all as specified and directed.

S&F of 35 W LED Street Light luminaire confirmining incliding all necessary arrangemet for fixing on Pole made up SITC of high quality integrated LED street light with a minimum system lumen of 4500 Lm and system wattage not exceeding 35 W with nominal effiiciency 110 lumen/Watt. CCT of 5700K with SDCM of <5 and CRI>70. The housing should be of non- Corrosive high - pressure die cast aluminum with heat resistant toughened clear glass to with stand extreme environments with PF>0.95. Life time of 50K Hrs @L70. The ingress protection should be minimum IP 66 with IK ratingof 0.7. The luniunaire should have 5 KV internal 10 KV external surge protection in the luminaire. incl takin down old unsv light fittings complete all as specified and directed.

S&F of 60 W LED Street Light luminaire confirmining incliding all necessary arrangemet for fixing on Pole made up SITC of high quality integrated LED street light with a minimum system lumen of 6600 Lm and system wattage not exceeding 60 W with nominal effiiciency 110 lumen/Watt. CCT of 5700K with SDCM of <5 and CRI>70. The housing should be of non- Corrosive high - pressure die cast aluminum with heat resistant toughened clear glass to with stand extreme environments with PF>0.95. Life time of 50K Hrs @L70. The ingress protection should be minimum IP 66 with IK ratingof 0.7. The luniunaire should have 5 KV internal 10 KV external surge protection in the luminaire. incl takin down old unsv light fittings complete all as specified and directed.

S&F of 70W LED Flood Light luminaire made up of Matt black ptextured powder coated pressure Die Cast aluminum housing and frame with heat resistant toughened clear glass fixed with SS screw/ Ant dust exposed lens, sturdiness and embossed brand name/ logo name of manufacturer on fixture. The luminaire should have a minimum system lumen output of 10800 lumens and 70 Watts. The fixture shall have a CRI of minimym 70. The fixture shall be designed for a system life of 50000 hours @ 70 % lumen maintenence , Ingress protection of IP 66 (lamp and gear compartement) and Mechanical impact resistance rating of IK>=07. The fixture driver should have an operaing voltage rang of 20-277V, surge protection of 10 KV, PF. 0.95, THD<10% inc taking down old unsv light fittings complete all as specified and directed

MAMTA ENTERPRISES (BID ID -3383381)

M/s Rahat Traders (BID ID -3376036)