Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹1.9 CrAccepted-Finance | ₹1.9 Cr | L1 | Accepted-Finance as per boq |
| 2 | L2₹2.1 CrAccepted-Finance | ₹2.1 Cr | L2 | Accepted-Finance as per boq |
| 3 | Rejected-Technical 223 02 WARD NO 10 A DHURI DISTT SANGRUR | DHURI | SANGRUR | PUNJAB | - | - | Rejected-Technical Disqualfied as per comparative chart |
| 4 | Rejected-Technical | - | - | Rejected-Technical Disqualified as per comparative chart |
| 5 | Rejected-Technical | - | - | Rejected-Technical Disqualified as per comparative chart |
Tender Value
₹2.5 Cr
EMD Value
₹5.1 L
Closing Date
14 Feb 2026, 6:00 pmClosed
Executive Engineer
JKPHC JAMMU
Construction of Civil Defence Office / Control Room At Akhnoor Village Mawa Karora Karangi (C. No.75)
2026_DGPJK_302411_1
75 of PHC JAMMU DIV /2025-26 Dated-05-02-2026
Open Tender
Civil Works
270 days
AKHNOOR-JAMMU
REFER PQ TERMS AND CONDITIONS
3 documents required · 3 mandatory
₹3,000
Executive Engineer, JKPHC Division Jammu
₹5.1 L
Executive Engineer, JKPHC NARWAL JAMMU
31 Mar 2026
5 Feb 2026
16 Feb 2026
5 Feb 2026
14 Feb 2026
5 Feb 2026
5 Feb 2026 - 9 Feb 2026
10 Feb 2026
Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soil.
Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil :
Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.
Extra for every additional lift of 1.5 m or part thereof in excavation/bankingexcavated or stacked material
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.
Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete.
Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :Treatment of soil under existing floors using chemical emulsion (Chlorophriphos/Lindane E.C. 20% with 1% concentration) @ one litre per hole, 300mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floor:
Providing and laying in position cement concrete of specified grade including curing butexcluding the cost of centring and shuttering. All work upto plinth level with:Providing and laying P.C.C in1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)
Providing and laying in position cement concrete of specified grade including curing butexcluding the cost of centring and shuttering. All work upto plinth level with:Providing and laying P.C.C in 1:2;4(1cement:2coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete
Providing and laying non-pressure of specified class R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement: 2 fine sand) including testing of joints etc. completeNP-3class(medium duty). 600 mm dia. R.C.C. pipe
Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)
Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) and curing complete
Applying a coat of residual Petroleum bitumen of grade VG-10 of appproved quality using 1.7 kg per square metre ondamp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soakedin kerosene oil
Providing and laying in position cement concrete of specified grade excl. the cost of centering and shuttering. All work up toplinth level 1:1.5:3 (1 cement: 1.5 fine sand: 3 graded stone agg. 20 mm nominal size) crushed.
Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)
Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete at all levels:- Thermo-Mechanically Treated bars of grade Fe-500D or more.
FORM WORK:- Centering and shuttering including strutting, propping etc. and removal of form for:
Foundations, footings, bases of columns etc. for mass concrete.
Columns, Pillars, Piers, Abutments, Posts and Struts
Lintels, beams, plinth beams, girders, bressumers and cantilevers
Suspended floors, roofs, landings, balconies and access platform
Edges of slab under 20cm wide
Stairs (excluding landings) except spiral staircases.
Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:6 ( 1 cement : 6 coarse sand)
Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level
Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand)
Extra for half Brick masonry in superstrcture above plinth level upto floor level
12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 coarse sand)
15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 6 ( 1 cement : 6 coarse sand) )
6mmcement plaster to ceiling of mix 1:3( 1cement :3 fine sand)
15mm cement plaster on the rough side of single or half brick wall finished with a floating coat of neat cement of mix : 1 : 4 ( 1 cement : 4 fine sand)
Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50mm thick with 20 mm nominal size stone aggregate.
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and pigmen etc. complete Size of tile 600x600 mm
Providing and laying Ceramic glazed floor tiles 300x300 mm Antiskid (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete In colour such as White, Ivory, Grey, Fume Red Brown
Providing and fixing 1st quality ceramic glazed wall tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. Size of tile 300x450 mm
Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade (Area of slab over 0.5 sqm) 18mm thick:-
Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite Work
Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2 mm thick
Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on new work ( two or more coats) over and including priming coat with water thinnable cement primer.
Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28litre/10sqm over and including base coat of waterproofing cement paint applied@ 2.20kg/10sqm); of approved brand and manufacture Asian/Nerolac/Berger/Dulux paints only all complete including scaffolding etc.; at all floor levels complete:- (Including cost / Carriage of material by Mechanical transport)
Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Sal wood
Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).
Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings /wooden frames with rawl plugs screws etc.
Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws 35mm
Extra for providing and fixing flush doors with decorative veneering instead of non-decorative ISI marked flush door shutters conforming to ISI: 2202 (Part-I) On one side only
Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :250x10 mm
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :150x10 mm
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125mm
Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :100mm
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.twin rubber stopper
Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.
Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.
Providing and fixing fly proof wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions all complete. With stainless steel grade 304 wire gauge with wire of dia 0.50 mm . With 2nd class teak wood beading 62x19 mm sqm
providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Second class deodar wood
Providing and laying integral cement based water proofing treatment including preparation of surfaces as required for treatment of roofs, balconies, terraces etc. consisting of following operation. A) Applying a slurry coat of neat cement using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/Brick Bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand ) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 ( 1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of Junctions of walls and slabs) c) After two days of proper curing appling a second coat of cement slurry using 2.75kg/sqm of cement admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick joint less cement mortar of mix 1 : 4 ( 1 cement : 4 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge including laying finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm/sq 3mm deep. e) The whole terrace so finished shall be flooded with waterf for a minimum period of two weeks for curing and for final test. all above operations to be done in order and as directed and specified by Engineer-in-charge. with average thickness of 120 mm and minimum thickness at Khurra as
Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design. In 75x75 mm deep chase.
Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement: 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete
Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge.
Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc. including welding, grinding, buffing, polishing and making curvature (wherever required ) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge complete including carriage, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.
Supplying and stacking of good earth at site including royalty (earth measured in stacks will be reduced by 20% for payment)
Supplying and stacking at site dump manure from approved source including carriage complete (manure measured in stacks will be reduced by 8% for payment) Screened through sieve of I.S. designation 16 mm
Mixing earth and sludge or manure in proportion specified or directed by officer in charge.
Spreading of sludge, dump manure or/and good earth in required thickness as per directions of officer in-charge (cost of sludge, dump manure or/and good earth to be paid separately)
Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.
Carriage of Materials with avg. lead upto 10km Sand
Stone agg. 10 Km by MT
Bricks 10 Km by MT
Providing and fixing tiled False Ceiling of specified materials of size 595x595mm in true horizontal level suspended on inter locking metal gridof hot dipped galvanized steel sections (galvanized @ 120 gms/sqm both side inclusive ) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick(minimum) sheet spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard manufactured from natural gypsum as per IS 2095 part-I and laminated with white 0.16mm thick fire retardant PVC film on the face sideand 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.
Conducting & providing soil investigation /bearing capacity test & preparation of site plan tree set on A2 size , architectural drawings , design of structure from reputed architect and structuraldesigner and also vetting of structural drawings from IIT/NIT/GCET or DIQC before execution of the work
( PLUMBING AND SANITARY INSTALLATIONS) SH: I China Ware
Providing and fixing white vitreous china pedestal type water closet(European type) with seat and lid , 10 liter low level white vitreous chinaflushing cistern and CP flush bend with fittings and C.I. brackets, 40mmflush bend, overflow arrangement with specials of standard make andmosquito proof coupling of approved municipal design complete,including painting of fittings and brackets, cutting and making good thewalls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.
Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer
Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.
Providing and fixing white vitreous china battery based infrared sensoroperated urinal of approx. size 610 x 390 x 370 mm having pre &post flushing with water (250 ml & 500 ml consumption), havingwater inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction ofEngineer-in-charge.
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as perI.S. 13983 with C.I. brackets and stainless steel plug 40 mm, includingpainting of fittings and brackets, cutting and making good the wallswherever required Kitchen sink with drainboard:510x1040mm bowl depth 250mm
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: Semi rigid pipe - 40 MM DIA
SH:II C.P Fitting and Accessories
Providing and fixing mirror of superior glass (of approved quality) and ofrequired shape and size with plastic moulded frame of approved makeand shade with 6 mm thick hard board backingRectangular shape 1500x450 m
Providing and fixing toilet paper holder with Flap made out of C.P Brass
Providing and fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106gms. .
Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms.
Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge
Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931
Providing and fixing 15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms
Providing and fixing 15 mm nominal bore C.P. stop cock (concealed) of standard design and of approved make conforming to IS : 8931
Providing and fixing 15 mm nominal bore C.P. brass angle valve forbasin mixer and geyser points of approved make conforming to IS : 8931
Providing and fixing 15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg.
SH III : SOIL, WASTE AND VENT PIPES
Providing and fixing soil, waste and vent pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing.110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B
Providing and fixing soil, waste and vent pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing.75 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B
Providing and fixing of Rain Water pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing.110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-A
Providing and Fixing of Floor Traps 110 mm with double chrome plated Cover one Grated and one closed and all other fittings required. Makes:- Astral/SFMC/Finolex
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement: 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominalsize), foundation concrete 1:4:8 mix (1 cement : 4 coarsesand (zone- III): 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finishedwithfloating coat of neat cement and making channels in cement concrete1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mmnominal size) finished with a floatingcoat of neat cement complete as perstandard design :Inside size 90x80 cm and 45cm deep including C.I. cover withframe (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg andweight of frame 15 kg) :With common burnt clay F.P.S. (non modular)bricks of classdesignation 7.5
SH IV: WATER SUPPLY
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot and cold water supply, including allCPVC plain and brass threaded fittings. This includes jointing of pipesand fittings with one step CPVC solvent cement and testing of jointscomplete as per direction of Engineer-in-charge.(SDR-11)Internal work Concealed fixing the pipe with clamps at1.00 meter spacingincluding cutting chases and making good thewall etc.
15mm nominal outer dia pipes
20mm nominal outer dia pipes
25mm nominal outer dia pipes
Providing and fixing on wall face un plasticised rigid PVC rain water pipes
Making soak pit 2.5 m diameter 3.0 meter deep with 45x45 cm dry brickhoney comb shaft with common burnt clay (non modular) bricks of classdesignation 7.5 bricks and S.W. drain pipe 100 mm diameter, 1.8 m longcomplete as per standard design
Providing and fixing 1 HP motor complete Job.
Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
Electrical items
Wiring for light point / ceiling fan point/exhaust fan point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
Providing Installation testing and commissioning of Ceiling Fans of approved brands with connections etc as required
Supply & Fixing of additional Fan rods
Supplying and fixing two module Stepped type electronic Fan Regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
Supply,installation,testing and commissioning of Ceiling LED Surface Light 12 watt day milky fitting with connections as required
Supply & Installation of Exhaust Fans With Stylish Plastic Exhaust 200 mm(8") in the existing opening including connections,testing commissioning etc as required
Supply & Installation of Bulk Head Lights including connections,testing commissioning etc as required
Providing ,installation,testing and Commissioning of 100 watt LED Flood light with connection etc as required
Supply and fixing of Ceiling rose on the existing junction box/wooden box including connections as required
Supply and fixing Modular Blanking Plate on the existing modular plate and switch box excluding modular plateas required
Supplying laying & making outdoor connections including aluminium lugs and other jointing materials for 3.5X 95 sqmm LT Power Cable ,Almunium Conductor, ARMOURED
Supplying laying & making outdoor connections including aluminium lugs and other jointing materials for 3.5X 50 sqmm LT Power Cable ,Almunium Conductor, ARMOURED
Supply ,instalation,fabrication and commissioning of Low voltage Sub Main Panel on 415 volts 3 phase 50 htzs of 1.6mm thick CRCA / Sheet of powder size 4X5 rft with stand . a)Providing and fixing of 250 amp TPN Al.Bus bar with required no. of thimbles etc (02 NO) b)250 amp 4 pole MCCB with breaking capacity 35KA c)100 amp 4 pole change over switch d)63 amp TPN (4No.) e)VSS meter/switch f) ASS meter/ switch g)CTs 200/5 amp rating h) 32 amp DP MCB 4No. I) 40 amp DP MCB 4No.
Supplying and fixing of following way horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
6 way (4 + 18) double door
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator
16 way, Double door
Supply & Fixing following size TPN MCB
Supply & Fixing following size DP MCB
Supplying and fixing of 5 amps to 32 amps rating 240/415 volts "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required of Approved Brand.
Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. Make :- /Anchor/finolex/polycab or Equivalent
2x1.5 sq. mm
2 x 2.5 Sqmm + 1 x 2.5 sqmm
2 x 4 Sqmm + 1 x 4 sqmm
2 x 6 Sqmm + 1 x 6 sqmm
2 x 10Sqmm + 1 x 6 sqmm earth wire
4 x 10Sqmm + 2 x 6 sqmm earth wire
Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc.& Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections for HEATING points etc. as required.
6 Module (200mmX75mm)
6 pin 15/16 A socket outlet & 15/16 A switch
5 pin 5/6 A socket outlet & 5/6 A switch
Supplying and fixing following 5 pin 5/6 A modular switch /socket on the existing modular plate & swich box including connections etc. as reqd.
Disposal of unwanted mulba/ material from the site of work including cheselling & repairing whereever required
Providing and fixing of 2 way AC Box with MCB mounting and connections etc as required.
Supply & fixing testing & commissioning of 2 Ton Hot & cold AC Inverter Series,3 Star including Copper pipe etc. as required
Supply & fixing testing & commissioning of wall mounted stabilizer for AC
Supplying and fixing of 1x18 watt LED fiiting 4 feet long wall /surface mounted including connections etc as required
Providing and fixing Single Bracket /Wash Basin Light decorative type surface mounted and complete with 9 watt LED Bulb
Supply and fixing Indicator on the existing modular plate and switch box excluding as required
Supply and fixing of modular Computer socket on modular zinc passivated box of 2 module
Providing & Laying Cat-6 Computer wire in existing Conduit
Spare Box for Cat 6
Supply & drawing 2 pair0.5 sqmm FR PVC Insulated annealed copper conductor,unarmoured Telephone cable in the existing surface/recessed steel/ PVC Conduit as required
Supplying and fixing of Telephone Socket outlet modular Switch/ Socket on the existing Modular Plate and switch box including connections but excluding modular plate as required
SITC of Photoelectric smoke detector of approved brand
SITC of manual call point of approved brand
SITC of Hooter of approved brand
SITC of 4 zone Fire Alarm Panel with battery backup of approved brand
SITC of 2x1.5 sqmm copper FRLS cable of approved brand
Analog CCTV cameras 2 MP HD; with colour night vision
16 CH DVR 1080P.
4 TB HDD
Connector
DC Pin
2250 INVERTER with Double battery
HDMI cable 2 mtr
3+1 CCTV cable
Supply and fixing of modular RACK for CCTV Cable etc.
PVC Conduit 25 mm
Supplying, Installation, Testing and Commissioning of 82.5 KVA, 3 Phase, 50 Hz ,415 volts. 0.8 pf Silent DG Set Diesel Engine & Alternator both mounted and aligned on a common MS base frame complete with AMF panel, fuel tank, Residential Exhaust Silencer, with batteries, AVM Pad,12 volt Battery lead fitted in Sound Proof acoustic enclosure with first fuel fill.
SITC of 100KVA Copper wound, Servo controlled automatic voltage stabilizer with MCCB and Bye Pass Switch and with of approved brand following specifications; a) Input voltage range = 300Volts to 460Volts (Phase to Phase) , b) Output voltage range = 415Volts + 1% (Phase to Phase),Frequency: 50 HZ. d) Capacity overload = 10% overload for four hour. e) Protection : Over Load & Short Circuit f) indoor type g) Unbalance type, Cooling shall be ONAN.
Construction of Tin Shed & Concerete Plate form for D G Set & Servo as required and as per the directions of the Engineer in charge
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
Chemical Earthing complete
Please Enable Macros to View BoQ information
stage.html
html • 0.04 MB
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.89 MB
BOQ_981360.xls
BOQ • 0.41 MB
Download all tender documents and submit your bid