Chief Minister Development Fund

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing & Fixing Air Walker of make Arihant/ Kompan/ Koochie/ Hugo / Ok Play/Leo. 1. Dimensions (LxWxH): 1100 x 450 x 1300mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. ‘U’ shaped main frame of NB 80mm (G.I.) ‘C’ Class Pipe, Leg Support frame of NB 50mm (G.I.) ‘C’ Class Pipe. 4.Handle frame pipes of NB 32mm (G.I.) ‘C’ Class. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored. 9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment made to EN16630 International standard for outdoor fitness equipment.

Providing & Fixing Situp Station of make Arihant/ Kompan/ Koochie/ Hugo / Ok Play/Leo. 1. Dimensions (LxWxH): 1500 x 1150 x 650mm 2. Fabricated with main frame of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 25mm (G.I.) ‘C’ Class Pipe. 4. Leg support of NB 65mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. Perforated MS Sheet for Back Support. 6. The back support Fixed on its top is made of perforated MS sheet of 2mm thickness. 7. All pipes are powder coated using Akzo Nobel or equivalent Paint of 80-120 micron thick. 8. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 9. Zinc primer paint is applied at all welding points prior to finishing. 10. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 11. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 12. Once the concrete is set, the equipment is fixed on to it. 13. High tensile steel with galvanized nut bolts are used for assembly. 14. Equipment made to EN16630 International standard for outdoor fitness equipment. 15. Self-Explanatory stainless steel label fixed on equipment for ease of use. 17. For the laying of foundation of equipment cc work shall be paid separately.

Providing & Fixing Air Swing of make Arihant/ Kompan/ Koochie/ Hugo / Ok Play/Leo. 1. Dimensions (LxWxH): 1150 x 900 x 1250 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Leg Support frame of NB 50mm (G.I.) ‘C’ Class Pipe. 4. Handle support frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 10. Foothold made of MS Sheet Metal with rounded edges to prevent impact and injury. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to EN16630 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use. 18. For the laying of foundation of equipment cc work shall be paid separately.

Providing & Fixing Horse Rider Station of make Arihant/ Kompan/ Koochie/ Hugo / Ok Play/Leo. 1. Dimensions (LxWxH): 1000 x 600 x 1100 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make 3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. Handle support frame of NB 50mm (G.I.) ‘C’ Class Pipe and other pipes of NB 32mm & NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 9. Foothold made of NB 32mm (G.I.) ‘C’ Class Pipe. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to EN16630 International standard for out door fitness equipment. For the laying of foundation of equipment cc work shall be paid separately.

Providing & Fixing Leg Press of make Arihant/ Kompan/ Koochie/ Hugo / Ok Play/Leo. 1. Dimensions (LxWxH): 2000 x 550 x 1600 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Seat Main frame of NB 50mm (G.I.) ‘C’ Class Pipe and Pipe connecting main post to seat main frame of NB 65mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 8. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe. 9. Seats made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment made to EN16630 International standard for outdoor fitness equipment. 16. Self-Explanatory stainless steel label fixed on equipment for ease of use. 17. For the laying of foundation of equipment cc work shall be paid separately.

Providing & Fixing Exercising Bar of make Arihant/ Kompan/ Koochie/ Hugo / Ok Play/Leo. 1. Dimensions (LxWxH): 1800 x 550 x 1500 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class pipe of approved make. 3. Main frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 8. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 9. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 10. High tensile steel with galvanized nut bolts are used for assembly. 11. Equipment made to EN16630 International standard for outdoor fitness equipment. 12. Self-Explanatory stainless steel label fixed on equipment for ease of use. 13. Pipe and sheet components should be cut by atleast 2KW laser machine having CNC made components welded using robot with atleast 2 metre welding range. 14. For the laying of foundation of equipment cc work shall be paid separately.

Providing & Fixing Arm Wheel of make Arihant/ Kompan/ Koochie/ Hugo / Ok Play/Leo. 1. Dimensions (LxWxH): 850 x 800 x 1800 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Wheel frame of NB 32mm with connecting spokes of NB 25mm, Pipe connecting main pilar with wheel frame of NB 50mm. All pipes must be (G.I.) ‘C’ Class Pipes. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 8. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 9. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 10. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 11. High tensile steel with galvanized nut bolts are used for assembly. 12. Equipment made to EN16630 International standard for outdoor fitness equipment. 13. Self-Explanatory stainless steel label fixed on equipment for ease of use. 14. For the laying of foundation of equipment cc work shall be paid separately.

Providing & Fixing Double Cross Walker of make Arihant/ Kompan/ Koochie/ Hugo / Ok Play/Leo. 1. Dimensions (LxWxH): 1600 x 600 x 1600 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Handle main frame of NB 50mm and other connecting pipes of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 4. Foot support frame of 96 x 46 x 3mm MS rectangular pipe. 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored. 9. Foothold made of Co-Polymer Plastic with rounded edges to prevent impact and injury. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment made to EN16630 International standard for outdoor fitness equipment. 16. Self-Explanatory stainless steel label fixed on equipment for ease of use. 17. For the laying of foundation of equipment cc work shall be paid separately.

Providing & Fixing Twister (Triple Standing) of make Arihant/ Kompan/ Koochie/ Hugo / Ok Play/Leo. 1. Dimensions (LxWxH): 1300 x 1300 x 1650 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Handle Main frame of NB 32mm (G.I.) ‘C’ Class Pipe. 4. Handle frame spokes of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 5. Foothold plate of made of MS Sheet Metal of 3mm thickness. 6. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 7. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 8. Zinc primer paint is applied at all the welding points prior to finishing. 9. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 10. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 11. Once the concrete is set, the equipment is fixed on to it. 12. High tensile steel with galvanized nut bolts are used for assembly. 13. Equipment made to EN16630 International standard for outdoor fitness equipment. 14. Self-Explanatory stainless steel label fixed on equipment for ease of use. 15. For the laying of foundation of equipment cc work shall be paid separately.

Providing & Fixing Rowing Machine of make Arihant/ Kompan/ Koochie/ Hugo / Ok Play/Leo. 1. Dimensions (LxWxH): 1250 x 800 x 1150 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. Handle support frame of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 9. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to EN16630 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use. 18. For the laying of foundation of equipment cc work shall be paid separately.

Providing & Fixing Pull Chair of make Arihant/ Kompan/ Koochie/ Hugo / Ok Play/Leo. 1. Dimensions (LxWxH): 2400 x 800 x 2000 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Seat main frame of NB 50mm (G.I.) ‘C’ Class Pipe, Pipe connecting main post with handle frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. Handle frame of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to EN16630 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless steel label fixed on equipment for ease of use. 18. For the laying of foundation of equipment cc work shall be paid separately.

Providing & Fixing Seated Chest Press of make Arihant/ Kompan/ Koochie/ Hugo / Ok Play/Leo. 1. Dimensions (LxWxH): 1800 x 700 x 2000 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make. 3. Seat Main frame of NB 50mm (G.I.) ‘C’ Class Pipe. 4. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and Environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to EN16630 International standard for outdoor fitness equipment. 17. Self-Explanatory stainless-steel label fixed on equipment for ease of use. 18. For the laying of foundation of equipment cc work shall be paid separately.

OUTDOOR EFFECT EPDM Flooring 36mm (30+6). Providing & laying 36mm EPDM Play Ground Safety Flooring (30mm SBR bottom layer + 6mm EPDM top layer) EPDM GRANULES of make OUTDOOR EFFECT manufactured under quality management system of ISO 14001-2015 compliance and Antimicrobial & Antifungal Tested Material, standard grain size 1.0- 4.0mm and laying in 4 layers i.e. Layer- 1, Polyurethane based primer coating. Layer-2, 36mm black rubber base particle long rubber stands/ SBR rubber crumb mix with 15% above component PU base binder styrene butadiene rubber/ synthetic rubber. Layer-4, 6mm EPDM GRANULES CHEMICALLY bonded with MDI 18-20% with single component of Diphenylmethane Discocyanate and paraffinic oil etc. Desing on base top layer by specialized team of installers according to the specification and shade as per the direction of engineer in-charge or manufacturer specification (C:C work for sub-base not i/c) and not in the scope of installation team.

Please Enable Macros to View BoQ information