SPL REPAIR TO BLDG NO A/4/91, A/4/92, A/4/140 AND PROVN OF PATHWAY FROM BLDG NO A/4/31 TO SPORT COMPLEX IN THE AREA OF AGE B/R-II UNDER GE PANAGARH

Amount

Excavating over areas, n.exc 1.5 m deep and getting out in soft/loose soil complete all as specified and directed.

M&L for 200 mm thick (in two layers of each 100mm thick) in pavings, with mix of fly ash, clinker & stone dust in the proportion of 1:3:6 (ie 10% fly ash, 30% clinker and 60% stone dust ) laying in layers n.exc 30cm thick, watering, ramming and compacted with hand/power roller 8 to 12 tonn roller to required camber and gradient complete all as directed by Engineer-in-Charge.” laid in layers n.exc. 15 cm thick, spread, levelled, and blinded with earth and rammed including watering complete all as specified and directed

M&L for broken stone hardcore of guage n.exc 63mm, deposited, spread and levelled in layers n.exc. 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate) as in sub base complete all as specified and directed

M&L for 75 mm thick PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in hardstanding laid in panels with and including use and waste of formwork and to divide the area in panels and finishing the surface even and smooth with out using extra cement fair complete all as specified and directed

Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’ when thickness of concrete slab is 75mm complete all as specified and directed.

M&L for chequered cement concrete tiles with mixture of grey cement and pigments 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over and including scredd bed or bedding layer of 15mm thick in cement mortar in 1:6 complete all as specified and directed

M&L for cement Concrete, 1:2:4, type B1 (using 20mm graded stone aggregate) as in bed block, coping, lintel upto 1.50 m span, cills, kerbs etc complete all as specified and directed

Removing excavated soil n.exc. 50m and depositing where directed at a level n.exc. 1.5m above the starting point complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles and removing rubbish off from the site complete all as specified and directed

M&L for fly ash brick straight or curved on plan exc 6 mtr mean redious built in CM (1:6) complete all as specified and directed

Taking down cement plaster, any description on brick or stone walls and ceiling, chajja, landing etc including racking of joints hacking for key scrubbing down with water etc and removing rubbish off from the site complete all as specified and directed

M&L for 15mm thick rendering in CM (1:6) on internal surfaces of brick masonry wall finished even and smooth without using extra cement complete all as specified and directed

M&L for 15mm thick rendering in CM (1:4) mixed with water proofing compound on external surfaces of brick masonry wall finished even and smooth with out using exrtra cement fair complete all as specified and directed (Note: Water proofiing item to be paid separately)

Supply only Liquid water proofing compound complete all as specified and directed. (Make : Pidilite Industries/ Impermo/Snowcem India Ltd/Sika)

M&L for preparation of new plastered surfaces of wall and applying three coat of white wash on walss complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. (Make: M/s Apex Ultima of Asian/ Weather Coat all guard of Berger/Xtra Tough of Shalimar)

M&L for completely removal of existing surface and applying two coats of oil bound destemper on wall surface over a coat of alkali resistant complete all as specified and directed.

M&L for preparation of old plaster surfaces after complete removal of existing surface and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed. (Make: M/s Apex Ultima of Asian/ Weather Coat all guard of Berger/Xtra Tough of Shalimar)

Dismantaling (corrugated,semicorugated) sheet in roof covering complete all as specified and directed.

M&L for pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in Ridges fixed with self tapping screws complete as specified and directed.

M&L for flat iron fillets (for securing wire mesh, CGI Sheets etc.), Hand rails, half round or other steel section including embeding in concrete and screwing etc, wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

Taking down chowkhats or frame n.exc 1.5 Sqm each with shutter(s) (without taking off shutters from the frame), complete all as specified and directed.

Taking down chowkhats or frame exc 1.5 Sqm but n.exc 4 Sqm each with shutter(s) (without taking off shutters from the frame), complete all as specified.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge complete shall as specified.

S&F powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge etc complete all as specified

S&F 4mm thick Figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 Sqm in each pane oil putty in square n.exc. 0.5m in each pane.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 100 mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed

S&F for 150 mm aluminium extruded handles, fabricated type anodised complete all as specified and directed

S&F 150 mm long aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed

S&F mild steel flat iron as in hold fast clamps small articles conforming to FE 290 GDE -E- 165 complete all as specified and directed.

M&L for PCC(1:3:6) type C1 (using 20 mm graded stone aggregate) as in bed blocks for hold fast including necesssary formwork, kerb stones etc complete all as specified and directed.

Dismantling floor hearth or wall tilling including cement mortar bedding, removing rubbish off the premises for minor repairs to floor in patches all as specified and directed.

M&L for 75mm thick Cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) as in sub base complete all as specified and directed

M&L for 40mm thick PCC 1:2:4 type B-1 (using 20mm graded coarse aggregate) in flooring complete all as specified and directed.

M&L for coloured non skid joint free ceramic tiles 7 to 8 mm thick (Square/ Rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc set and jointed in neat cement slurry over and including 15 mm thick screed bed or bedding layer in cement mortar (1:6) complete all as specified and directed.

M&L for glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick cement plaster in CM (1:3) on brick or concrete surfaces complete all as specified and directed.

M&L for 75 mm thick PCC type C-1 1:3:6 (using 20 mm gradded stone aggregate) finishing the as in Plinth protection surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in surface channels and drains complete all as specified and directed

Dismantling wrought Iron or mild steel work of any description not otherwise provided for wind tie complete all as specified and directed.

S&F roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. Fe-410-W (Gde-E-250) quality-A complete all as specified and directed

M&L for applying one coat of synthetic enamel paint on old steel surfaces of any description over 10cm in width or girth not otherwise described incl preparation of surfaces and complete all as specified and directed

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on newly steel surfaces of any description over 10cm in width or girth not otherwise described incl preparation of surfaces and complete all all specified and directed.

Taking up or down steel tubing and connection including cleaning for refixing or removed to store, 15 mm dia bore complete all as specified and directed.

S&F GI tubing 15mm bore medium grade with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed

S&F Vitreous China Squatting pan ‘Orissa’ pattern, size 580 X 440 mm, white, with integral foot rests and with ‘P’ or ‘S” trap, (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc and including provision of lime concrete bedding, complete all as specified and directed. (Make: Cat part no.20042 of Hindware or equivalent make of parryware/Cera)

S&f vitreous china wash basin, white, flat back, size 550 x400mm (for hospital use) excluding taps, waste, chain and plug and porcelain stopper but including brackets any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed

S&F viterous China urinals, bowl type (back or corner wall type), of size 465 x 355 x 265mm white complete including providing and fixing plugs, bedding urinal agianst wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed

S&F 15mm bore piller taps cast copper alloy,with capstan heads,chromium plated,screwed down, fancy type high pressure, with or without lettred 'HOT or COLD' with long screwed sunk and fly nuts complete all as specified and directed.

S&F 15 mm bore stop valve cast copper alloy screwed down, high pressure, with crutch or but-ter fly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F PVC connection 15mm size PTMT nuts of length 600mm complete all as specified and directed.

S&F grating square 150mm size of PTMT (minimum weight 100 gms) complete all as specified and directed.

S&F 10 litre capacity PVC valveless, syphonic action type low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size complete (with brackets) complete all as specified and directed. (Make:- Hindware, Parryware, Commander (Slim Line)).

S&F bib taps cast copper alloy 15mm bore with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

Supply flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern complete all as specified and directed.

S&F tubular towel rail /towel ring 20mm dia D type and 60cm long between flanges of brass chromium plated complete all as specified and directed.

S&F shelf of PTMT fixed with and including chromium plated brass screw and wooden/plastic cleats ( min weight 300 gms) complete all as specified and directed.

S&F 75mm PVC (SWR) floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F as in repair 75mm dia PVC pipe fixed to wall or laid in trenches set in cement mortar with and including MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc complete all as specified and directed.

S&F PVC bends plain (any radius) for 75mm bore PVC pipes complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coat oil bound distemper over a coat of alkali resistant primer all as specified and directed.

S&F 2nd class hard wood plain solid straight chowkhat and frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joint complete all as specified and directed.

S&F Factory made 35 mm thick 2nd H.W plain framed panelled shutters( two panel) with lock rail and panel of 9mm thick B.W.P commercial ply . The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed.

S&F 35mm th 2nd class hard wood, glazed & skeleton shutters, open rebated & prepared to receive glass, (two panel to receive wire gauge) gauge etc, eges of framing plain, chamfered as rounded fitted with cut and mitere beads for securing etc complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete complete all as specified.

M&L for preparation of newly wooden surfaces of any description not otherwise described over 10 cm girth or width and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple ( bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and slidibg bolts of extruded section or cast-aluminium alloy complete all as specified and directed.

S&F floor door stopper of brass body 140 mm long and tongue with rubber shoes complete all as specified and directed.

Dismantling of wall or ceilling boards of any thicness including cover fillets complete all as specified and directed

S&F 605mm x 605mm Anodised aluminium snap grid frame work for false ceiling with all necessary aluminum angle & Tee arrangement with and incl fixing cleats screws etc complete all as specified in SSR and directed.

S&F Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long complete all as specified.

S&F 6mm thick (non asbestos fiber) designer building boards fixed in aluminium frame work in ceilling flat or sloping with screw complete all as specified.

Demolition of cement concrete (un-reinforced) n.exc 15 cm thickness of any description and in any position and removing rubbish off from the site complete all as specified and directed

M&L for joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm set and jointed in neat cement slurry and pointed in white cement in verticle surfaces over and including 10mm thick in CM (1:3) complete all as specified and directed.

S&F capacity 1000 Ltrs rotational moulded polyethylene water storage tanks (Cylindrical, vertical with closed top) confirming to relevent IS complete including provision of all inlet outlet overflow and drain pipe fitting complete all as specified and directed by Engineer in Charge

S&F of high pressure PTMT float valve with epoxy coated alluminium rod and high density polythelene ball screwed for iron pipe 25 mm dia with fly nut complete all as specified and directed.

M&L for 25 mm bore gate valve cast copper alloy screwed down high pressure with clutch handle screwed both ends for Iron pipe complete all as specified and directed.

S&F 25 mm bore GI Tubing medium grade in Trenches/ Floor/Pillar and connection including fitting like socket /Union/Tee/Reducer Nipple etc complete all as per specified and directed.

S&F 50 mm bore GI Tubing medium grade in Trenches/ Floor/Pillar and connection including fitting like socket /Union/Tee/Reducer Nipple etc complete all as per specified and directed.

EM PORTION Taking down carefully aluminium conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified and directed.

M&L for point wiring for light point/ fan point, one light/fan/ exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers or modular cover plate with frame of suitable size and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLS PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. (Note: Quoted rate deemed to be included for necessary chasing/cutting and making good the surface)

All as per item No 86.00 mentioned here-in-above but One 3 pin 5 Amps socket out let points on independent board complete all as specified and directed

All as per item No 86.00 mentioned here-in-above but 5 Amp socket on same board with other switches complete all as specified and directed.

M&L for wiring for socket out let on independent Boards controlled by one, one way switch using 4.0 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including Modular pressed steel terminal switch boxes of diffrent module and 4.0 sqmm nominal cross sectioanl area multistranded copper conductor, PVC insulated unsheathed FRLS cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified. (Note: Quoted rate deemed to be included for necessary chasing/cutting and making good the surface)

S&F switch piano flush type, single pole , 5/6 Amps, one way complete all as specified.

S&F switch socket combination 2 in 1 multipurpose 5 pin , (6 Amps ) flush type controlled by one switch complete all as specified.

S&F socket outlets 2 in 1, 3 pin, 5/6 Amps flush type230/240 V complete all as specified and as directed .( For Same Board only)

S&F switch socket combination 5 in 1 , 6 pin , (5/16 Amps ) flush type controlled by one switch complete all as specified.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified.

S&F lamp holder, PVC/polycarbonate type with back plate straight or anfular suitable for batten fittings complete all as specified.

S&F security light fittings 25 watts, minimumm lumen output 100 lumen/ Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete suitable for pole dia 25mm complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as directed.

S&F 18 W LED light fitting wall mounted batten 4'ft , extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 18 watt,6000K including necessary connection complete all as specified and directed.

S&F in repairs epoxy powder coated sheet metal enclosure for DBs, double door, Single pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel, neutral link and incoming contact complete all as directed.

S&F MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed. (Note :-Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

S&F in repairs MCB SPN 6-32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed. (Note :-Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth wire electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth wire encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. (Note :- (i) If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department. (ii) Testing to be carried out by the contractor in presence of Engr- in- Charge , entered in the eath testing register, prepared and to be maintained by the contractor & submited to Concerned JE E/M. (iii) T&P and testing instrument(Meger) to be provided by the contractor at own cost.)

S&F ventilating exhaust fan 300 mm sweep 230 volt AC complete with louver and all accessories including cutting hole of suitable size, making good surface by doing plaster and applying two coat of distemper complete with fixing arrangement to wall connected with twin core twisted flexible copper conductor (23/.0076) of suitable size all as directed.

Taking down carefully aluminium conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified.

S&F stepped type electronic fan regulator flush type 240 Volts ISI marked complete all as specified .

S&F two single core ,6 sqmm nominal cross sectional area multistranded copper conductor FR cable, PVC insulated unsheathed 1100 Volts grade drawing in and including nd including suitable size PVC conduit (ISI marked), concealed, including 6 sqmm nominal cross sectional area multistranded copper conductor FR cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified. (Note: (i) 3 runs cable and conduit pipe will be measured as single unit. (ii) Quoted rate deemed to be included for necessary chasing/cutting and making good the surface).

S&F recessed mounted 2' x 2 ' LED luminaire 36 watts for grid ceiling minimumm lumen output 100 lumen/Watt, pre-treated CRCA frame powder coated with diffused Profied including necessary connection complete all as specified and directed.

S&F Vertical distribution board double door TPN 4 way with IP 43 multiphase outgoing suitable for mounting 100 Amps as incomer with Bus bars, Neutral links complete with all accessories complete all as directed.

S&F MCCB of 4 pole , 415 volts of capacity 100 Amps with breaking capacity of 16 KA Fixed thermal and fixed magnetic setting including necessry connection complete all as specified and directed.

Taking down of AC ceiling fan of any sweep & any height and opening the fan and oiling, greasing and replacement of unserviceable accessories and servicing, complete overhauling and re-assembling and testing complete for efficient functioning and hanging it back in position including provn of 0.5 Sqmm copper flexible twin twisted cable (length n.exc 0.5 metre) from ceiling rose to fan as directed by the Engr-in-Charge. (Note : Accessories such as gun metal bush and split pin and jam nut shall be measured and paid under relavtem here-in-after).

M&L for painting of ceiling fans upto 1400mm sweep carefully, dismantling fan blades and paint with one coat of synthetic enamel paint including filling cavities with filler after cleaning all dust etc complete all as directed.

Supply, laying / fixing / connecting, testing and commissioning of 10 Sqmm x 4.0 core LT under ground cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cable (heavy duty) with multistranded aluminium conductor,1100 Volts grade in trenches/on wall/poles laid in ducts/inside protection pipe of the following cross sectional area including cable glands,lugs and suitable size of MS saddle clips (where ever cable laid in ceilings / walls without cable duct) all as directed by the Engr-in-Charge for the following ratings (Note: Excavation,sand cushioning,brick will be measured and paid separtely).

Excavating in trenches, n.exc 1.5 m wide and n.exc 1.5 m in depth for laying of cables, pipes etc. and getting out including trimming the sides and forming bottom surfaces to required levels in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, and well ramming in layer n.exc 25 cm thick in soft/loose soil complete all as specified and directed.

M&L for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete as specified and directed . (Note : Punned thickness 18 cm shall only be considered for payment)

Supply and lay in trenches fly ash bricks, for cable protection all as specified and directed by the Engr-in-Charge.

S&F Pipes galvanized, 50 mm bore “light grade”, supplied and laid complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement or specified.

MS ROYAL CONSTRUCTION INDEX NO 158 2010 BKP

NATIONAL CONSTRUCTION CO

Hooghly Construction Co.

UNIVERSAL TRADING

SUPARNA TRADING

rahul enterprise

simplex infra project