Certain repair to joinery, plumbing, plastering, tilling etc and sunken treatment of Md accn of JCOs/OR at Yadunath and Manekshaw enclave under AGE B/R-I, GE Gurdaspur.

Amount

Demolition of cement concrete of any description and in any position(above/below of ground level) not otherwise specifically provided as in sunken floor, plinth protection, roof kerb, foundation etc. all as specified and directed.

M&L plaster 15mm thick in cm 1:3 in sunken portion of slab using waterproofing compound all as specified and directed Note : Water proofing compound shall be measured and paid separately.

Supply only integral water proofing compound.

M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) incl bitumen primer @ 0.40kg/ sqm laid on applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m by forced application with butane torch over entire roof area with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in after cleaning surface complete all as specified and directed and all as per manufacturer's instructions.

M&L for PCC 1:5:10 type E2 using 40 mm graded stone agg as in filling, fdn and mass concrete in sunken floor complete all as specified and directed.

M&L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in sub base for receiving the floor finishes complete all as specified and directed.

S&F prepartion of new surface and applying two coats of aluminum paint on above of APP Membrane complete all as specified and directed.

Roughing the surface of old concrete floor picking sweeping clean and washing down with water to remove dust/mud etc.and brushing neat cement slurry @ 3kg/Sqm.

M&L for cement concrete 1:2:4 type B-0 using 12.50mm graded stone aggregate as in roof padding averaging thickness of 50 mm complete all as specified.

M&L for ceramic glazed dark shade coloured tiles of size 350x250x 7mm/ 450x350x7mm thick joint free on and including 10mm thick screed bed in CM(1:4) set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles on vertical surfaces of wall as in skirting/ dado and dismantling of existing tile complete all as specified.

M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm to 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:4 and dismantling of existing tile complete all as specified.

M & L for Green Marble work 16-18 mm thick (table rubbed and polished) in steps, jambs, pillars window cills, cooking platforms, stair case and like in cement mortar ( 1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 15 mm thick screed bed in CM 1:4 and dismantling of existing marble with screed complete all as specified and directed.

M&L for 75mm thick cement cocnrete type C-1 (1:3:6) (20mm graded aggregate) as in plinth protection finishing the surface even and fair complete all as specified and directed by EIC.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone agg) as in roof kerbs or mud stops, rounded or chamfered on edges with WPC complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be measured and paid separately.

Demolition of brick work or stone boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc

M&L for brick work with sub class 'B' old size bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.

Material and Labour for repairing of RCC projections, chajjas, roofs, facia etc. by necessary preparations i.e. scrapping, cutting, chiseling, dusting and cleaning exposed reinforcement, surfaces of damaged, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete (1 : 2 : 4) using 12.5mm graded crushed stone aggregate and finished with cement sand mortar (1:3) using coarse sand in patches area n.exc 5 Sqm each and thickness of RCC member exc 50mm including applying two coats of Finishes to match with the existing surfaces in at any height complete all as specified. Note: - Cost of formwork and welded mesh, bldg ht upto 12 mtr, shall be deemed to be included in unit rate quoted by the Contractor.

Taking down cement plaster of any description on brick walls on concrete surfaces etc including racking out joints hacking for key,scrubbing down with water etc from walls and ceiling surfaces of any description complete all as specified and directed.

M&L for rendering 15mm thick plaster in cement mortar 1:4 on brick or concrete surfaces of walls, finished surface even and fair with WPC upto ht. 12 mtr complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be measured and paid separatel

M&L for rendering 12mm thick plaster in cement mortar 1:6 on brick or concrete surfaces of walls, finished surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 5mm thick plaster on ceiling in cement mortar 1:3 finished surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L preparation of new plaster surface and applying two coats of cement base paint on wall surface complete all as specified and directed by EIC.

M&L preparation of new plaster surface and applying two coats of Oil bound distemper of wall over a coat of chalk whiteing primer on plastered surface wall complete all as specified and directed by EIC.

M&L preparation of new plaster surface and applying three coat of white wash on wall complete all as specified and directed by EIC.

M&L preparation of new plaster surface and applying three coat of white wash on ceiling complete all as specified and directed by EIC.

S&F steel window box type made of ERW tube hollow P section of size 60mmX25mm double rebated outer frame comprising double shutters i.e. guaged skelton & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 complete incl one shop coat of zinc chromate primer with two coat of synthetic enamel paint incl taking down old existing window :- (i) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (ii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iii) MS Tower bolt 150mm long-02 Nos per leaf (iv) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (v) Cleat 55mm long of hollow square 15mmX12mm -02 Nos per leaf (vi) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (vii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). (viii) Painting with one shop coat of zinc chromate primer. Note: Wire cloth, glass shall be measured and paid for separately

S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts, painting with one shop coat of zinc chromate primer incl one shop coat of zinc chromate primer with two coat of synthetic enamel paint incl taking down old existing window/ventilator complete all as specified and directed. Note: Glass/ wire cloth shall be measured and paid for separately

Demolition of cement concrete (Reinforcment) of any description upto 12 m ht. All as specified and directed by Engr-in charge.

Form work to rough finished surface of concrete flat to soffits of shelve, chajja, fins etc including supports over hangs.

S&F 6mm dia and over TMT bar cut to length bent to shaps including cranking binding spirraly, hooping, hooking end and binding with MS wire (anealed) not less then 0.9 mm dia or securingwith clips as specified and directed.

M&L for RCC in 1:2:4 type B-1(using 12.5 mm graded stone agg) as in chajjas facia, shelves etc and similar work all as specified.

S&F in repair Stainless steel cockroach trap with hole, round 101mm dia complete all as specified and directed Make:- Prayag (Cat No. FT-21 M) or equivalent.

M&L for Preparation of old plastered surface of walls rubbing down, making good holes, cracks, etc and stopping etc on existing distempered surfaces and applying one coats of cement base paint on wall ht upto 12m incl cleanning the floor/, joinery, surfaces, glass pans complete all as specified and directed by EIC.

M&L for preparation of old plastered surface of walls rubbing down, making good holes, cracks, etc and stopping etc on existing distempered surfaces and applying one coat of oil bound distemper over a coat of 1mm thick wall putty complete all as specified and directed.

M&L for Preparation of old plastered surface of walls rubbing down, making good holes, cracks, etc and stopping etc on existing distempered surfaces and applying one coats of oil bound distemper on wall incl cleanning the floor/, joinery, surfaces, glass pans complete all as specified and directed by EIC.

M & L for preparation of old plastered surfaces of wall by brooming down, making good holes, cracks, etc and applying one coat of white wash ht upto 12m incl cleaning the floor/ joinery surfaces, glass pans all as directed by Eng-in-charge

M & L for preparation of old plastered surfaces of ceiling by brooming down, making good holes, cracks, etc and applying one coat of white wash incl cleaning the floor/ joinery surfaces, glass pans all as directed by Eng-in-charge

M&L for preparation of old painted wooden surface exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted steel surface exc 10cm width or girth and applying one coat of synthetic enamel paint ht upto 12m complete all as specified and directed.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter for the chowkats) complete all as specified and directed.

Taking down chowkats with shutter exc 1.50 Sqm but n exc 4.00 sqm each (without taking off shutter for the chowkats) complete all as specified and directed.

Taking down shutter of any description exc 1.00 Sqm but n.exc 2.00 Sqm each complete all as specified and directed.

S&F pressed steel frame for doors with one or more rebate including necessary fixing lugs, hings, lock strike, plate etc complete of size 105x60mm all as spd including two coats of painting over a coat of primer and filling PCC 1:2:4 (type-B0) in the frames complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.

S&F 30 mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels on both side complete all as specified and directed.

S&F 2nd class hard wood (Hallock) factory made glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc. but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc , sizes of members of shutters as specified in SSR Part-I, Section 8 clause 8.24 (a) complete all as specified and directed.

S&F Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F in repair Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each complete all as specifiwd and directed.

S&F in repair 4mm thick sheet glass ordinary quality and glazing with oil putting in squares nexc 0.50 Sqm each incl hacking out of old broken glass panes from wooden or steel frame complete all as specified and directed.

M&L for preparation of new wooden surface exc 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surface exc 10cm width or girth and applying two coat of synthetic enamel paint complete all as specified and directed.

S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs, including roller and roller plate joint through welding/bolt in metal/wooden frame to be carried out complete all as specified and directed.

S&F Aluminium anodized barel tower bolt of extruded section 150mm long ISI marked complete all as specified and directed.

S&F aluminium alloyed handle fabricated type anodized of size 150 mm long ISI Marked complete all as specified and directed.

S&F 100mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 through bolt or with screw complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door 300 mm long ISI Marked bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified and directed.

Supply and fixing in repair cutrain rod 20mm dia of Mild steel with PVC Coated with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug including taking down existing curtain rod complete all as specified and directed.

S&F in repair 18 mm thick plywood , grade BWR, laminated on both side with decorative choice lamination , Incl fire resistant, moisture resistant type fixed with screws to timber/steel frame work Incl 6mm thick lipping fixed with nails on all sides on cupboard, kitchen cabinets and like complete all as specified and directed by EIC.

S&F aluminium alloyed handle fabricated type anodized of size 100 mm long complete all as specified and directed.

S&F 75mm size hasp and staple safety type aluminium anodised brass with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed.

Repairs, easing & adjusting of shutter without taking down shutters of any description exc 1.00 sqm & nexc 2 sqm each.

M&L cement concrete type D-2, 1:4:8 using 40mm stone aggregate as in sub base complete all as specified and directed. (to raise level only)

Dismantling of existing tiles and M&L for 60 mm thick PCC (M-35) factory made with gray cement and no pigment interlocking tiles/ paver block of shape/ size as conforming to IS 15658, joints will be filled with fine sand, complete all as specified and as directed by Engr-in-Charge. Note Sand will be paid under relavent item.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

S&F in repair stainless steel L-type jet spray with 1m hose pipe for fitting in WC complete all as specified and directed by Engineer-in-Charge.

S&F 500 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks (cylindrical vertical with closed top) hoisted and fixed in postition all as specified in SSR Part I including dismantling of water tanks complete all as specified and directed.

S&F in repair ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 20mm bore complete all as specified and directed.

S&F in repair stop value 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repair stop valves or angel valve cast copper alloy 15mm bore fancy type chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed. Make:- Prayag (Cat No. 7510) or equivalent.

S&F in repair bib taps cast copper alloy 15mm bore fancy type chromium plated alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make:- Prayag (Cat No. 7506) or equivalent.

S&F in repair Pillar taps, cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore and fixed. Make:- Prayag (Cat No. 7502) or equivalent.

S&F in repair Brass chromium plated shower rose fancy type 125mm size with swivel joints, any size, including fixing to steel pipe or union with brass CP arm 195mm long, 15 mm size complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia, D type, 60 cm long with flanges complete all as specified and directed by Engr-in-Charge.

S&F machine cut kota stone slab flooring 20-22mm thick over cement screed base 20mm thick in 1:6 jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (with bees wax polish) including demolition existing complete all as specified and directed by Engineer-in-Charge.

S&F in repairs vitreous china wash down water closet (pedestal pattern) fixing with bolts ,white colour, incl SS L-type jet spray with 1 m hose pipe, connection to trap, and to flushing pipe, anti-syphonage pipe, etc. incl seat covercomplete including making good to floor complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with internal foot rest with `P’ or `S’ trap, integral foot rest including water connection to trap and flushing pipe etc complete and bedding in PCC 1:7:12 type F-2 complete all as specified and directed.

S&F in repair vitreous China wash basin, with pedestal white flat back, size 550x 450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets and coupling complete all as specified and directed.

S & F in repair PVC low level flushing cistern 10ltr capacity, with syphonic, action PVC float valve, brackets and 32mm bore PVC flush pipe etc complete all as specified and directed.

S&F in repair PVC waste pipe 32mm dia 800mm to 1200 mm long fixed to wash fitting of wash basin and sink all as specified and directed.

S & F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair brass spindle with nylon washer and removing leakage of water of any concealed type suitable for 15 to 25mm bore pipe complete all as specified.

S&F in repair tap/valve head/ handle 15mm dia cast copper alloy fancy type chromium plated round/square hole complete all as specified and directed.

S&F in repair Grating doom 100 mm dia with waste hole of PTMT. complete all as specified and directed.

S&F GI tubing 15mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked including taking up and down complete all as specified and directed.

All as per Srl item No 88 above but fixing only (old serviceable pipe re-used).

S&F GI tubing 20mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked including taking up and down complete all as specified and directed.

All as per Srl item No 90 above but fixing only (old serviceable pipe re-used).

S&F GI tubing 32mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings including taking up or down old pipe complete all as specified and directed.

Dismantling of cast iron ,PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches , if required.

S&F PVC (SWR)pipes 110mm dia in any length with rubber ring joint fixed to wall/floor upto 12m height complete all as specified and directed.

S&F PVC (SWR)pipes 75mm dia in any length with rubber ring joint fixed to wall/floor upto 12m height complete all as specified and directed.

S&F in repair PVC (SWR) bends 110mm dia, in any radius, complete all as specified and directed.

S&F in repair PVC (SWR) bends 75mm dia, in any radius, complete all as specified and directed.

S & F in repair 110 bore PVC(SWR) Branch pieces (Single T), single (equal or unequal ), ordinary or inverted ) ( or with parallel branches with oval access door complete all as specified and directed.

S & F in repair 75 bore PVC(SWR) Branch pieces (Single T), single (equal or unequal ), ordinary or inverted ) ( or with parallel branches with oval access door complete all as specified and directed.

S&F in repair PVC vent cowl of size 110mm.

M&L in repair for PVC(SWR) floor trap plain including jointing with solvent cement 100mm dia complete all as specified and directed.

M&L in repair for PVC(SWR) floor trap plain including jointing with solvent cement 75mm dia complete all as specified and directed.

S & F in repair Stack clamps (110 mm pipe) out of 20 mm by 1.5 mm galvanised Mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S & F in repair Stack clamps (75 mm pipe) out of 20 mm by 1.5 mm galvanised Mild steel incl stays, bolt and nuts and securing ends of stays to wall or roof complete all as specified and directed.

Note: A Schedule of Credit for old/unserviceable demolished/dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

Harbhajan electric co (BID ID -3083409)

KAILASH CONSTRUCTION CO (BID ID -3081019)