REPAIR TO STROM DRAIN PATH AND COMPOUND WALL AT DRDO ESTATE UNDER AGE BR PASHAN

Amount

Demolition of brick work or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins,pillars,arches etc, and clearing off the premises, complete all as specified and as directed by Engineer-in-Charge.

Demolition of reinforced cement concrete of any description and in any position above or below ground level, complete all as specified and as directed by Engineer-in-Charge.

Taking down cement plaster on brick / concrete / stone surface including raking out joints, hacking for key scrubbing down with water etc, complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Cement concrete 1:4:8, type D-2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete, sub base etc, complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6, complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 but except stone, complete all as specified and as directed by Engineer-in-Charge.

Material and labour for pre-cast cement concrete block masonrytype C1 1:3:6 (20mm graded aggregate) with solid blocks exc.10cm in width and setting in cement mortar 1:6, Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for cement concrete for copping in PCC 1:3:6 Type C-1 ( 20mm graded aggregate) including necessary formwork, Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for PCC 1:3:6 type C2, (using 40 mm graded stone aggregates) as in surface channel and drains, Complete all as specified and as directed by Engineer-in-Charge.

Extra over stone walling for hammer dressing to face stones and dressing or face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses with maximum depression 20 mm on face from straight edge held against the dressed surface Granite or Trap Stone, complete all as specified and as directed by Engineer-in-Charge.

Material and labour for keyed pointing to random rubble, uncoursed or brought upto courses in CM 1:3, complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement, Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for precast cement concrete type B1 1:2:4 (using 20 mm graded aggregate) as in Drain cover slabs, culvert slab etc and similar articles with plain faces set in cement mortar(1:4), complete all as specified and as directed by Engineer-in-Charge.

Material and labour for mild steel deformed TMT bars 8 to 10 mm dia cut to length bent to shape required including cranking bending spirally etc and binding with M.S. wire (annealed) not less than 0.9 mm dia or securing clip, Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fix in repairs 110mm dia PVC ( SWR) Pipes single socketed, in any length with rubber ring joints, fixed to wall or laid in trenches etc, Complete all as specified and as directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), Complete all as specified and as directed by Engineer-in-Charge.

Dismantling of kerb stones set and pointed using cement mortor complete all as specified and directed.

Material and labour for factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3, including making joints with or without grooves (thickness of joints except at sharp curve shall not be more than 5 mm), including making drainage opening for wherever required complete all as specified and directed.

Material and labour for Cement concrete 1:4:8, type D-2(using 40mm graded stone aggregate) 75 mm thick as in sub base, complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 15 mm thick screed bed in CM 1:6 or bedding layer for laying floor finishes, Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for cement concrete paving tiles 300X300X25mm thick, rubber moulded; with white cement and pigments set, jointed and pointed in net cement slurry in floors, and cut and polished, Complete all as specified and as directed by Engineer-in-Charge.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of (crushed stone sand) sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand, Complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15 cm thickness (below or above GL), Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Cement concrete 1:2:4, type B -1 (using 20mm graded stone aggregate) 100 mm thick as in hardstanding, Complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces, Complete all as specified and as directed by Engineer-in-Charge.

Dismantling of wrought iron and steel work of any description and in any position as any fencing grills, Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for MS angle posts, struts in fencing including cutting to shape as directed and drilling holes, notching for wire etc, flat iron fillets, bolts etc including all necessary drilling, bolting, riveting, welding etc and similar work conforming to Fe 290-) or grade E-165, Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe-290 (Gde E-165), Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fix in Hard drawn steel wire fabric, mesh size 50mm x 3.0mm dia each way , weight n. exc 4Kg per sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia, Complete all as specified and as directed by Engineer-in-Charge.

Dismantling fencing wire mesh, any type, Complete all as specified and as directed by Engineer-in-Charge.

Fixing only PVC coated chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire, Complete all as specified and as directed by Engineer-in-Charge.

Supply only PVC coated Chain link MS galvanised fencing, any size or type, Complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm & n exc 10cm long, Complete all as specified and as directed by Engineer-in-Charge.

Demolition of precast concrete articles/ precast concrete block walling etc, Complete all as specified and directed by Engineer - in Charge

OM GANESH CONSTRUCTION

VENKATESHWARA ENTERPRISES

SLB Enterprises