Loading
Loading…
Loading…
Tender Value
₹1.0 Cr
EMD Value
₹2.0 L
Closing Date
6 Apr 2026, 4:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
ELECT.G
17 conditions · 5 needing a document upload
Financial Eligibility Criteria: (Ref: RB letter No. 2022/CE-I/CT/GCC- 2022/POLICY : Advance Correction Slip No.-1 dt 14.07.2022) The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-I, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The intending tenderers should possess a valid electrical contractor license at the time of opening of tender, issued by any state government & same should be submitted along with tender documents by all bidders including working contractors of this unit otherwise offer shall be summarily rejected....... IT SHOULD BE NOTED BY THE TENDERER THAT ELECTRICAL LICENSE UNDER RENEWAL AT THE TIME OF TENDER OPENING WILL NOT BE CONSIDERED AND OFFER WILL BE SUMMARILY REJECTED. IT IS THE RESPONSIBILITY OF TENDERER TO UPLOAD VALID ELECTRICAL CONTRACTOR LICENSE ON THE DATE OF TENDER OPENING.
All requisite documents mentioned in clause 3.7 of the tender document attached pertaining to constitution of firm/concern. (As applicable).
33 conditions · 5 needing a document upload
The rate to be quoted by tenderer shall be inclusive of all state/central taxes including GST. THE TENDERER SHOULD UPLOAD VALID GST REGISTRATION CERTIFICATE ALONG WITH THE OFFER.
The tender shall comply with General Condition of contract (GCC),2022 of Indian Railways (file attached). and its latest amendment, if any. The tenderer shall submit the offer after duly satisfying himself/herself with the GCC,2022 in general.
Tenderers are required to upload the Bank details as per Annexure-XII (Real Time Gross Saving (RTGS)/National Electronic Fund Transfer (NEFT) Model Mandate Form)of tender document.
Tenderers are required to upload requisite details as per Annexure-VIIB (DETAILS OF CONTRACTUAL PAYMENT RECEIVED IN LAST THREE FINANCIAL YEARS AND CURRENT FINANCIAL YEAR) without which the offer is liable to be rejected.
Tenderers are compulsorily required to upload Affidavit as per Annexure-XXIV along with tender document, without which the offer will be considered incomplete and will be rejected summarily.
All requisite documents/credentials mentioned in clause 3.5 of the tender document attached pertaining to his/their technical and financial eligibility. (As applicable).
All requisite documents mentioned in clause 3.7 of the tender document attached pertaining to constitution of firm/concern. (As applicable).
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Upload your bank details i.e. Name of the Bank along with Bank Branch Code, Account Number, IFSC Code as per Annexure-J (Real Time Gross Saving (RTGS)/National Electronic Fund Transfer (NEFT)(Model Mandate Form)) of tender document
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
No post tender correspondence for submission of additional documents shall be entertained after opening of the Technical & Commercial offers. Even suo-moto post tender letters of the tenderer/s shall be treated as Null & Void.
This tender complies with Public Procurement Policy (Make in India) Order 2017, dated 15/06/2017, issued by Department of Industrial Promotion and Policy, Ministry of Commerce, circulated vide Railway Board letter no. 2015/RS(G)/779/5 dated 03/08/2017 and 27/12/2017.
IF ANY DISCREPANCY IS FOUND IN THE TENDER DOCUMENT, NAMELY SOR ITEM DESCRIPTION, SPECIAL TENDER CONDITION ETC., CLARIFICATION CAN BE SOUGHT FROM THE OFFICE OF SRDEE/G/DLI, DRM OFFICE, STATE ENTRY ROAD, NEW DELHI.
This tender complies with Railway Board instructions for Startups (recognized by Department of Industrial Policy and Promotion, Ministry of Commerce and Industry) for exemption from payment of Bid Security as detailed in GCC 2022 as amended from time to time. Such Startup firms may note that no other exemption is applicable to them in this particular tender.
On account payment, contractor shall submitted indemnity bond with validity up to the completion/extended period in the prescribed format (please refer Annexure-XXVIII) at the contractor's cost, vesting the ownership of such material with the railways.
After opening of tender, any document/credential pertaining to technical, financial eligibility and available Bid Capacity constitution of firm etc. shall neither be asked nor be entertained/ considered under any circumstances and no claim or representation whatsoever from the tenderer in this regard shall be entertained. Scanned copy of the documents, uploaded by the tenderer shall be clear & readable. However Railway reserves the right to ask for any clarification on the documents/credentials already submitted by the tenderer along with the offer. ii)Tenderer may have to produce the original Documents in physical form at short notice whenever asked by Railway at any stage of tender evaluation process or even after finalization of tender. iii)In E-tender, all submissions of documents are to be uploaded on web-site. There may be last minute hic-cups and delay in uploading the Documents and payment of Earnest Money etc. Tenderer's/Prospective bidders are advised to upload their offer well in time. Railway will not be responsible for any delay/non submission of offer due to any reason whatsoever
Payment clause as per special conditions 100% payment will be done after successful supply, installation, testing and commissioning of actual work done by the tenderer and on certification by the Railway representative. No part payment shall be made for supply of material.
Electrical work regarding development of heavy repair and maintenance facilities for Heritage rolling stock at steam locomotives at Rewari.
67-SRDEE-G-DLI-2025-26
67-SRDEE-G-DLI-2025-26
Open
Works - General
12 Months
Delhi, Delhi
₹0
₹2.0 L
6 Apr 2026
13 Mar 2026
23 Mar 2026
97 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 10124356.00 Below/P | ||
| — | 210.00 | — | — | ||
| "Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required confirming to CPWD General Specifications for Electrical Works Part-I Internal - 2023, CPWD DSR (E&M) 2022 & as per Explanatory Note. Group C | — | — | — | 2,96,100 | |
| — | 500.00 | — | — | ||
| Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required of reputed make as per IS, IE rules and site requirement and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023, CPWD DSR (E&M) 2022 & as per Explanatory Note. Size: 2 x 2.5 sq. mm + 1 x 2.5 sq. mm earth wire | — | — | — | 1,32,000 | |
| — | 500.00 | — | — | ||
| Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required of reputed make as per IS, IE rules and site requirement and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023, CPWD DSR (E&M) 2022 & as per Explanatory Note. Size : 2 x 4 sq. mm + 1 x 4 sq. mm earth wire | — | — | — | 1,39,500 | |
| — | 200.00 | — | — | ||
| Wiring for circuit / submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required of reputed make as per IS, IE rules and site requirement and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023, CPWD DSR (E&M) 2022 & as per Explanatory Note. Size : 2 x 6 sq. mm + 1 x 6 sq. mm earth wire | — | — | — | 72,200 | |
| — | 100.00 | — | — | ||
| Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per Explanatory Note. | — | — | — | 44,400 | |
| — | 50.00 | — | — | ||
| Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per Explanatory Note. | — | — | — | 27,850 | |
| — | 50.00 | — | — | ||
| Supplying and fixing 3 pin, 5A ceiling rose on the existing junction box/wooden block including connections etc. of reputed make complete as per IS, IE rules and site requirement and conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023, CPWD DSR (E&M) 2022 & as per Explanatory Note. | — | — | — | 3,500 | |
| — | 600.00 | — | — | ||
| Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation((upto 75-100 cm depth and not less than 35 cm wide ), sand cushioning, protective covering and refilling the trench etc. as required as per detail drawing approved by competent authority and conforming to IS 1255 (Reviewed in 2016) or latest & as per Explanatory Note. Upto 35 sq. mm | — | — | — | 2,11,200 | |
| — | 600.00 | — | — | ||
| Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation((upto 75-100 cm depth and not less than 35 cm wide ), sand cushioning, protective covering and refilling the trench etc. as required as per detail drawing approved by competent authority and conforming to IS 1255 (Reviewed in 2016) or latest & as per Explanatory Note. Above 35 sq. mm and upto 95 sq. mm | — | — | — | 2,52,600 | |
| — | 600.00 | — | — | ||
| Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation((upto 75-100 cm depth and not less than 35 cm wide ), sand cushioning, protective covering and refilling the trench etc. as required as per detail drawing approved by competent authority and conforming to IS 1255 (Reviewed in 2016) or latest & as per Explanatory Note. Above 95 sq. mm and upto 185 sq. mm | — | — | — | 2,80,200 | |
| — | 200.00 | — | — | ||
| Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation(upto 75-100 cm depth and not less than 55 cm wide & maintaining gap not less than 20 cm between the cables), sand cushioning, protective covering and refilling the trench etc as required as per detail drawing approved by competent authority and conforming to IS 1255 (Reviewed in 2016) or latest and explanatory note. Upto 35 sq. mm | — | — | — | 53,800 | |
| — | 200.00 | — | — | ||
| Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation(upto 75-100 cm depth and not less than 55 cm wide & maintaining gap not less than 20 cm between the cables), sand cushioning, protective covering and refilling the trench etc as required as per detail drawing approved by competent authority and conforming to IS 1255 (Reviewed in 2016) or latest and explanatory note. Above 35 sq. mm and upto 95 sq. mm | — | — | — | 57,200 | |
| — | 200.00 | — | — | ||
| Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation(upto 75-100 cm depth and not less than 55 cm wide & maintaining gap not less than 20 cm between the cables), sand cushioning, protective covering and refilling the trench etc as required as per detail drawing approved by competent authority and conforming to IS 1255 (Reviewed in 2016) or latest and explanatory note. Above 95 sq. mm and upto 185 sq. mm | — | — | — | 65,000 | |
| — | 200.00 | — | — | ||
| Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. In case of any demolition of PCC, RCC, road, wall surface etc. the contractor should ensure repairing of the same on own expenses as per site requirement and satisfaction of railway representative conforming to IS 1255 (Reviewed in 2016) or latest & as per Explanatory Note. Upto 35 sq. mm (clamped with 1mm thick saddle) | — | — | — | 11,000 | |
| — | 200.00 | — | — | ||
| Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. In case of any demolition of PCC, RCC, road, wall surface etc. the contractor should ensure repairing of the same on own expenses as per site requirement and satisfaction of railway representative conforming to IS 1255 (Reviewed in 2016) or latest & as per Explanatory Note. Above 35 sq. mm and upto 95 sq.mm (clamped with 25x3mm MS flat clamp) | — | — | — | 26,000 | |
| — | 200.00 | — | — | ||
| Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. In case of any demolition of PCC, RCC, road, wall surface etc. the contractor should ensure repairing of the same on own expenses as per site requirement and satisfaction of railway representative conforming to IS 1255 (Reviewed in 2016) or latest & as per Explanatory Note. Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) | — | — | — | 32,800 | |
| — | 25.00 | — | — | ||
| Earthing with 40 mm dia GI pipe class 'B' 4.5 meter long earth electrode as per IS:3043 (latest version)to achieve earth resistance less than 5 ohms including construction of masonry enclosures with hinged cover plate of cast iron with locking arrangement (approx. size 400 mmx 400 mm) on top, provision of earth plate, connections from earth electrode to switch gear/pole as per drawing & as per Explanatory Note. | — | — | — | 1,43,775 | |
| — | 125.00 | — | — | ||
| Supplying and laying 25 mm X 5 mm G.I strip confirming to relevant IS as per IS:3043 (Latest version), fixing on surface or as per site condition, clamping or fixing with suitable arrangement as per site requirement, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50 mm) & as per Explanatory Note. | — | — | — | 19,250 | |
| — | 500.00 | — | — | ||
| Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required as per IS:3043 (Latest version) and as per Explanatory Note. | — | — | — | 27,500 | |
| — | 2.00 | — | — | ||
| Earthing with 600x600x3mm thick copper plate earth electrode as per IS 3043(Latest version), to achieve earth resistance less than one ohm, including construction of masonry enclosure with hinged cover plate of cast iron with locking arrangement (Approx. size 600x600 mm) on top, watering pipe, connections from earth plate to top with 40x6mm copper stip in 50 mm dia pipe class 'B' provision of earth plate as per drawing and as per Explanatory Note. | — | — | — | 21,834 | |
| — | 10.00 | — | — | ||
| Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode confirming to relevant IS as per IS:3043 (Latest version), including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm) conforming to CPWD DSR(E&M) 2022 & as per Explanatory Note. | — | — | — | 9,720 | |
| — | 65.00 | — | — | ||
| "Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal(Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body. Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based) for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply, Ceiling Fan compliant to IS 374:2019 or latest fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required. 1400mm, service value >= 6.0 CM/Min/Watt, air delivery 245 CM/Min (Minimum) conforming to CPWD DSR(E&M) 2025 item no. 9.2.4 & as per Explanatory Note. | — | — | — | 1,77,905 | |
| — | 700.00 | — | — | ||
| Supply and recessing/fixing of PVC conduit pipe of 40mm size conforming to IS:9537 Part-III:1987 (or Latest version) with accessories junction box, bends etc. including making chase, plastering/clamping etc. as per site requirement conforming to IS 9537 (Part 3) latest & as per Explanatory Note. | — | — | — | 41,300 | |
| — | 700.00 | — | — | ||
| Supply, Fixing, testing & commissioning of following sizes FRLSH PVC insulated multi stranded copper (annealed) conductor single core cable conforming to IS 694 (or Latest Version), and drawing in Laid (recessed /surface) PVC conduit pipe for wiring of point wiring / circuit wiring / sub main / main as required including connections, testing and commissioning. Size = 1x1.5 sq.mm. & as per Explanatory Note . | — | — | — | 9,100 | |
| — | 2100.00 | — | — | ||
| Supply, Fixing, testing & commissioning of following sizes FRLSH PVC insulated multi stranded copper (annealed) conductor single core cable conforming to IS 694 (or Latest Version) , and drawing in Laid (recessed /surface) PVC conduit pipe for wiring of point wiring / circuit wiring / sub main / main including connections, testing and commissioning. Size = 1x2.5 sq.mm . & as per Explanatory Note . | — | — | — | 37,800 | |
| — | 400.00 | — | — | ||
| Supply, Fixing, testing & commissioning of following sizes FRLSH PVC insulated multi stranded copper (annealed) conductor single core cable conforming to IS 694 (or Latest Version) , and drawing in Laid (recessed /surface) PVC conduit pipe for wiring of point wiring / circuit wiring / sub main / main including connections, testing and commissioning. Size = 1x4.0 sq.mm. & as per Explanatory Note . | — | — | — | 10,400 | |
| — | 300.00 | — | — | ||
| Supply and recessing/fixing of PVC conduit pipe of 25mm size conforming to IS:9537 Part-III:1987 (or Latest version) with accessories junction box, bends etc. including making chase, plastering/clamping etc. as per site requirement conforming to IS 9537 (Part 3) latest & as per Explanatory Note. | — | — | — | 9,300 | |
| — | 300.00 | — | — | ||
| Supply Laying, testing and commissioning of 2Cx2.5 sq. mm copper armoured cable complete as per latest IS and IE rules & as per Explanatory Note. | — | — | — | 34,500 | |
| — | 50.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED light luminaire, having system wattage 1x18-20 watt complete. LED tube and inbuilt LED driver, CRCA body powder coated, complete with all mounting arrangement, accessories. The LED based 4 ft. tube light (lamp) shall be conforming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per Explanatory Note. | — | — | — | 32,150 | |
| — | 60.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED light luminaire, having system wattage 2x18-20 watt. LED tube and inbuilt LED driver, CRCA body powder coated, complete with all mounting arrangement, accessories. The LED based 4 ft. tube light (lamp) shall be confirming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per Explanatory Note. | — | — | — | 65,280 | |
| — | 20.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED down lighter, housing aluminum die cast, white powder coated and PMMA diffuser having system wattage 15-18 Watt complete with all mounting arrangement, accessories complete confirming to CEE/NR's spec. No. CEE/NR/121- Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121- Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per Explanatory Note. | — | — | — | 14,880 | |
| — | 10.00 | — | — | ||
| Supply, fixing, testing and commissioning of 380mm sweep, 1400 rpm (approx) propeller type exhaust fan complete in all respect as specification and as per site requirement, including grouting of nut, bolts, washer and with the suitable fasteners conforming to IS 2312 & IS 302 or latest and other relevant IS/IEC standards . Make Bajaj, Usha, Havells, Orient or equivalent and as per explanatory note | — | — | — | 32,380 | |
| — | 15.00 | — | — | ||
| Supply fixing testing and commissioning of Heavy duty wall mounted air circulator fan 600 mm (24 inch), 1200 RPM industrial weather proof air circulator fan complete as per IS 2312 & IS 302 or latest and other relevant IS/IEC standards & as per explanatory note. | — | — | — | 1,10,115 | |
| — | 10.00 | — | — | ||
| Supply & erection of hot dip galvanized octagonal pole 5 Mtrs. long Double Arms, confirming to IS 2629/BSEN ISO 1461 latest version with top 70 mm and bottom 130 mm around face made of 3 mm thick, steel base plate size 200 x200x12 mm complete with appropriate sleeve at the top of the pole for mounting arm bracket 300 mm long (or as per site requirement) suitable for LED street light fittings including casting, muffing with cement concrete foundation (1:2:4) painting, earthing and foundation GI nut, bolts with washer and smart pack junction box with 1A single pole MCB and terminals. Pole junction box shall be sealed with water proof tape and display of danger sticker. Scope of work also include designing of pole for achieving uniform illumination and desired lux level as per Rly. Board guidelines and contractor shall get this design through computer modelling method from reputed manufacturer and will be submitted in hard/soft copy to Railways for approval. Note- Wiring in between pole junction box to fitting shall be done through 3 cores 1.5 sq. mm double insulated weather proof cables conforming to IS 456 & other relevant IS/IEC standards & as per Explanatory Note | — | — | — | 90,180 | |
| — | 20.00 | — | — | ||
| Supply, fixing, testing and commissioning of 45-50 watt LED based street light luminary with cool white light, pressure die cast aluminum housing, IP 66 or better having system complete confirming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per Explanatory Note. | — | — | — | 59,300 | |
| — | 125.00 | — | — | ||
| Supply, fixing, testing and commissioning of LED based highbay luminary with IP 66 having system wattage 150-155 Watt complete confirming to CEE/NR's spec. No. CEE/NR/121- Elect/PS/2018 (Rev-'3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121- Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per Explanatory Note. | — | — | — | 11,61,250 | |
| — | 1.00 | — | — | ||
| Supply, Eraction, Testing & Commissioning of 16 meter high mast system suitable for 9 Nos. LED flood light luminaries with the help of suitable equipment including accessories & control panel for high mast system, shall have provision of RCBO in place of MCB from I/C side. Each high mast shall also have one twin dome aviation obstruction light with 2 nos. LED lamp of Make BAJAJ, Osram, PHILIPS, GE or equivalent ; conforming to IS 875 (Part 3) (latest version) for wind load considerations, IS 2062 (latest version): For structural steel used in pole fabrication, IS 17740 :2022 (or latest ) : For high mast lighting system design and installation & as per Explanatory Note. | — | — | — | 2,45,192 | |
| — | 9.00 | — | — | ||
| Supply, fixing, testing and commissioning of 150 watt LED based flood light luminary with cool white light, pressure die cast aluminum housing, IP 66 or better having system wattage complete confirming to CEE/NR's spec. No. CEE/NR/121-Elect/PS/2018 (Rev- '3') or latest at Tech Spec-I attached & PCEE/NR's spec. No. PCEE/NR/121-Elect/PS/2019 (Rev- '4') at Tech Spec-II attached or latest & as per Explanatory Note. | — | — | — | 63,450 | |
| — | 1.00 | — | — | ||
| Supply, Fixing, Testing & Commissioning of astronomical timer based control panel for High Mast tower lighting suitable for 25A 4 P. contactor as per model No. Alpha Rex3 D21, 1 channel Cat Part 412654 of Legrand or equivalent. Panel should be double door weather proof type complete and conforming to IEC 61439-1 & 2, IEC 60947 and as per explanatory note. | — | — | — | 9,479 | |
| — | 1.00 | — | — | ||
| Fabrication, supply and erection of Fencing around the high mast in square shape size 2M x 2M and height 1.5M from ground level fabricated from MS angle size 40x40x6mm, MS Flat size 40x6mm and wire mesh made of 8SWG wire and 1M wide hinged type lockable door as per drawing approved by Railway including grouting, CC platform around the high mast above 0.30M above ground level and painting, danger plate etc. complete as per site requirement and as per explanatory note. | — | — | — | 7,230 | |
| — | 2.00 | — | — | ||
| Supply, fixing, testing and commissioning of 150 liter/Hrs L water cooler. Storage type self contained drinking water cooler, operation on 230V AC 50 Hz (Non CFC refrigerant), cooling cap. (in L/hr )-150, storage Cap. (in Lts) 150, Max Energy Consumption -1550 W, Power Factor = or more than 0.85, Tank sheet material-Stainless steel (Grade A-IS304), Thickness of sheet (in mm) 0.8. equal to or more than, Water Tank cover material -Stainless steel (Grade A IS304) thickness 0.8 and lid bottom sheet material and thickness-Alluminium sheet material & thickness-Aluminium sheet 1.5 (in mm ), operating voltage 230 V ac single phase 50 Hz, Confirming to IS -1475 or latest, ISI marked, warranty on site as per IRS terms & conditions or OEM whichever is maximum, warranty on compressor as per IRS terms & Condition or OEM whichever is higher. Make:- SIDWAL,BLUESTAR or equivalent & as per Explanatory Note | — | — | — | 98,500 | |
| — | 2.00 | — | — | ||
| Supply, installation, testing & commissioning of 25 ltrs. stationary storage type electric water heater (Geyser) having BEE star rating:- 5 star, installation: Vertical, ABS Body, element, Tank Capacity: 25 ltrs complete, confirming to IS: 2082:2018 or latest and IS: 302 latest and as per site requirement and as per Explanatory Note. | — | — | — | 22,588 | |
| — | 4.00 | — | — | ||
| Supply, fixing, testing and commissioning of 25A/32A, DP, 30 mA RCCB AC type confirming to IEC 60947 with 10KA short circuit withstand capacity complete with enclosure conforming to CPWD General Specifications for Electrical Works Part-I Internal - 2023 & as per explanatory note. | — | — | — | 10,760 | |
| — | 10.00 | — | — | ||
| Design, manufacturing, supply, fixing, testing and commissioning of rolling examination LED based lights complete with 03 Nos. 30 watt LED flood light, IP-66 with cover and suitable locking arrangement as per drawing approved by competent authority and as per actual site requirement complete & as per Explanatory Note. (The mounting structure should be G.I angle iron size 50x50x3 mm, Iron Zali 32 mm x32 mm) | — | — | — | 2,37,500 | |
| — | 10.00 | — | — | ||
| Supply, fixing, testing and commissioning of LT distribution board surface mounting/recessed double door out door type made up of CRCA sheet sheet with anti corrosion treatment and suitable, IP 54 phosphatised powder painted complete with neutral link, earth point, Din rail and prewired confirming to IEC 60947 or latest of make ABB, Siemens, L&T, Schneider, Legrand or equivalent with following items of matching make to be fixed in distribution board, confirming to IEC:61439 or latest, IE rules and site requirement. It should be rodent entry proof. It should also include well dressing and coding of circuit. It should also include proper tagging on electrical wires/cables which clearly indicate the incoming point and outgoing point of wires/cables & as per Explanatory Note 63A 4P RCBO 100 mA= 01 No. (Incoming) 6-32A MCB SP ""C"" Series =18 Nos. (Outgoing)" It should be rodent entry proof. It should also include well dressing and coding of circuit IP2X terminal , reversible door with 180 degree opening, cement spill protection, detachable gland at top and bottom and short link for MCBs. | — | — | — | 1,32,070 | |
| — | 2.00 | — | — | ||
| Design, Supply, fixing, testing and commissioning of front operated double door type weather proof outdoor type feeder pillar body made of CRCA sheet sheet with anti corrosion treatment and suitable having IP 65 protection (MCCB - Incoming & MCCB - Outgoing) comprising with the following MCCB's fixed in it of make: Siemens, L&T, Schneider, Legrand or equivalent conforming to IEC 60947 & IS/IEC:61439 or latest with digital measuring instrument & bus-bar arrangement and as per latest IS, IE rules and site requirement. It should be dust and vermin proof and powder coating as per IS 13871-2021 (or latest version) & as per Explanatory Note. 4P MCCB 250Amps 36 kA with adjustable thermal & fixed magnetic release = 01 No. (Incoming) 4P MCCB 125Amps 36 kA with adjustable thermal & fixed magnetic release = 02 No. (outgoing) 4P MCCB 63Amps 36 kA with adjustable thermal & fixed magnetic release = 04 No. (outgoing) | — | — | — | 2,15,818 | |
| — | 1.00 | — | — | ||
| "Design, manufacturing and supply of package type 11 kV/433 V outdoor substation, 630 KVA made from GI enclosure complete as required conforming to IEC 62271-202 only and relevant IS ,as per explanatory note ,specification and Tech Spec-III as applicable for the rating , internal arc of 21 KA/1 sec. IAC A & B on HT compartment. 630 KVA 11 KV/433 V DYN oil type, hermetically sealed energy efficiency level 2 transformer (BEE star Rated 2) with corrugated wall , without conservator , type of design & Top Bushing for HT & LT with off load tap switch of rating +5% to -5% @ 2.5%. 11 kV 630 A 21 KA/3 sec Non extensible Ring main unit compact switchgear consisting of 3 no. fixed motorized VCB module in SF6 insulated stainless steel enclosure (2.5 mm thick, SS304 grade) and with Bus PT metering module. Incomer from transformer : 800 Amps 433 V 4P 50 Hz 50 KA fixed motorized type Air circuit breaker (ACB)- 01 No. 400 A MCCB 4P 36 KA with adjustable thermal & fixed magnetic release = 02 Nos.(Outgoing). 200/250 A MCCB 4P 36 KA with adjustable thermal & fixed magnetic release = 02 Nos.(Outgoing)" | — | — | — | 49,80,000 | |
| — | 500.00 | — | — | ||
| Laying, testing and commissioning of 11kV HT PVC/XLPE armored power cable of the following size in ground/ under the road/ under the track/ on pole/ in existing GI pipe/ Hume pipe etc. including excavation sand cushioning, protective covering and refilling the trench etc. as per Explanatory Note. size 3Cx150 sq.mm. | — | — | — | 2,88,500 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC-2022-ACS10_merged.pdf
ATTACHMENT
TECHSPEC-I.pdf
ATTACHMENT
TECHSPEC-II.pdf
ATTACHMENT
TechSpecIIICSSspec.pdf
ATTACHMENT
TenderDocument67-SRDEE-G-DLI-2025-26.pdf
ATTACHMENT
SpecialConditions67-SRDEE-G-DLI-2025-26.pdf
ATTACHMENT
ExplanatoryNote67-SRDEE-G-DLI-2025-26.pdf
ATTACHMENT
2026_03_13IndianRailwaysStandardGeneralConditionsofContractApril2022AdvanceCorrectionSlipNo_111.pdf
CORRIGENDUM
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .