REPAIR REPLACEMENT TO ROOF SHEET FALSE CEILING FLOOR TILES PLASTER DOOR AND WINDOW TO TEMP BLDGS AT MIL STN BIKANER

Amount

Taking down cement plaster on brick or conc surfaces including racking out joints hacking for key, scrubbing down with water etc.

Demolition of cement concrete in ground floor and pavings n.exc 15cm thick below or above ground level including tiles and similar works complete all as specified.

Demolition of brick or stone masonary including all necessary arches, pillars, quions etc built in cement mortar.

Taking down chowkhat or frames exc 1.50 Sqm n.exc 4 Sqm (without taking down shutters from the frames)

Do but n.exc 1.50 Sqm

Taking down door shutter of any desc exc 1 sqm but not exc 2 sqm and refixing in the same opening.

Taking up or down steel water tubing 15mm dia and connection ,incl cleaning for refixing

Taking up or down steel water tubing 20mm dia and connection ,incl cleaning for refixing

Dismantling water tanks and removing to store

Dismantling of cast iron or PVC , jointed incement mortar pipes up to 100 mm bore in any position

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

Dismantling structural steel work as in trusses nexc 10.00 mtr span .

Dismantling of existing false ceiling of ac sheet etc

Dismantling Asbestos cement Corrugated sheets in roof covering including ridges .

Dismantling timber scantling 40 sq cm and over in section, in any position complete.

M&L for brick work with fly ash bricks old sized bricks ,straight or curved on plan exc 6 m mean radious built in cement mortar 1:6.

M&L Brickwork with flyash bricks, old sized bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4.

M&L for brick work with sub class 'B" bricks , old sized bricks straight or curved on plan exc 6 m mean radious built in cement mortar 1:6.

M&L steel work in tubular trussess/ purlins incl spl shaped washer etc. using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St-240. complete all as specified and directed by Engineer-In-Charge.

Erection and fixing only steel work in roof trusses including special shape washers et. Complete.

M&L framed brackets of angles or tees with web and flanges cut to shape, drilled and countershunk for screw, including bending and welding angles, as necessary, guser plate, riveting, etc. n exc. 10 kg brackets, confirming to Fe. 290 Gde -E-165 (Brackets over 10 kg each to be measured under structural steel ) complete all as specified and as directed by Engineer-In-Charge.

S&F Mild steel bolts.exc. 5 cm length not exc. 10 cm length (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends, each screwed end to be fittied with washers and one hexagonal or square nut 11 to 15 mm neck dia complete all as specified and as directed by engineer-in-charge.

M&L for rolled section as inframing cladding , glazing and the like fixed with angle cleats and connecting plates conforming to Fe- 410-w (gde-250) quality-B.

S&F(plain or chequered ) channels ,square cut or notched ( oridinary and counter sunk) forming holes , w/o any attatchment.

M&L for pre painted galvalume aluminium zinc coated GI based corrugated steel Sheet high rib profile tile pattern color coated 0.5 mm thick of 550 Mpa Tensile strength sheets as in roof covering and fixed as per manufacturers instruction (design as app by Engg in charge complete all as spfd .

M&L Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

M&L 6mm thick asbestos cement corrugated sheets in roofs, walls fixed with L-type or cranked hook bolts.

Do but fixing only

M&L Asbestos cement two piece adjustable ridge 6mm thick fixed with Lor J hooks / coach screws

M&L Composite cement ceiling board 4 mm thick in ( 595 mmX595 mm ) pannel (Make-everest ramco or eql.) designer ceiling pre finished conforming to IS 14862 type B cateogory three incl GI frame , grid work,hold fast,suspended with suspender along with holding down bolt complete . (Note: Ceiling board shall confirming to IS-14862 ,shall be fire resistant , Moisture resistant and ceiling shall be suspended with suspenter and adjuster .)

Providing and fixing Exposed metal frame ceiling with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600 mm grid.(Framework for the gid will be measured and paid separately)

M&L Anodised aluminium snap grid frame work for false ceiling all as specified

M&L for preformed material for plugging the holes in AC / CGI sheets as reqd .

M&L for hardcore of gauge nexc 63mm , deposited , spread and levelled in layers nex 15cm thick watered and rammed to a true surface in order to raise the low lying area in the plinth plrotection.

M&L for providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified.

M&L for 15mm thick rendering on fair faces of brick surfaces finished even and smooth W/O using extra cement in cm 1:4 complete all as specified and as directed by Engineer-in-Charge.

M&L for 15mm thick rendering on brick or concrete surfaces in cm 1:6 finished even and smooth w/o using extra cement

M&L for rendering 5 mm thick on fair faces of concrete surfaces in ceilings in cement mortar 1:3 and finished fair and even without using extra cement.

M&L for 40-50mm thick sand stone slab not exc 2mtr in length, punched dressed self faced set and pointed in CM 1:4 as in sun-shades, chajjas, shelves, cills landings, cover stone including cutting chasing as directed

M&L for 15mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes.

M&L for 15mm thick rendering on fair faces of brick works in cement mortar 1:4 finished even and fair for receiving tiles as in dado.

M&L for 40 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as floor finishes complete all as specified and as directed by Engineer-in-charge.

S&F 38 mm wide 3 mm thick Glass dividing strips, fixed as per design reqd .

S&F 20-25 mm thick single piece machine cut kota stone slab in flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and mirror polishing as in repairs complete incl roughing the surface all as spd and as directed by Engineer-in-charge.

Cutting to existing kota stone flooring including minor repairs and polishing complete

M&L coloured Non skid ceramic tiles exc 0.11 Sqm and nexc 0.18 Sqm , 7mm thick in floors set and jointed in neat cement slurry and pointed in coloured cement to match the floor .

All as per item above but on vertical surface as in skirting including backing coat in rendering 15 mm thick CM 1:4.

M&L for Vitrified tiles colored 600x600mm and10mm thick as in floors jointed in neat cement slurrry and pointed in white cement sluurry to match the shade of existing surfaces.(Note:The contractor shall have no claim on difference what so ever on shade /colour of tile)

Do but in vertical surfaces including backing coat in rendering 15 mm thick CM 1:4.

M/L for Non Skid ceramic tiles (size of each tile exc 0.06sqm and n exc 0.11 sqm) 7mm thick laid and jointed with cement slurry (in portions) and pointed with coloured cement to match in floor.Colour approved by the Engr in Charge.

S&F galzed ceramic colored tiles as in vertical surfaces 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry (in portions) and pointed with white or colored cement to match

M&L cement concrete (1:4:8) type D2 using 40mm graded stone aggregate as in foudation, filling, sub base and mass concrete all as specified.

M&L for cement concrete rich colored chequered tiles machine pressed with imported pigment finish (mirror/rough cast) of size 300mmx300mmx(25 mm to 40 mm ) thick set and jointed with neat cement slurry

M&L For PCC type B1(1:2:4) using 20 mm graded cushed stone agg as in copingto path ,edging ,benching and the like incl form work

M&L for PCC type C1 1:3:6 using 20mm graded crushed stone aggregate as in surface channel and drain beads including all necessary form work..

S&F 125 x 60mm pressed steel frames for doors with one or more rebate including necessary fixing lugs, hinges lock strike plate etc complete as specified including a coat of shop coat zinc chrome primer.

PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in filling in pressed steel frames complete all as specified and as directed by Engineer-in-Charge

S&F 35mm thick Factorymade second class hard wood plain framed pannelled shutter (two panels and double shutter) with lock rail and pannel or 9mm BWP comerical ply or 12mm venered particle board with comerical face venering on both faces. The size of rail and style as per IS-1003 part kilin seasoned

S&F 2nd class hardwood 35 mm thick glazed and skeleton shutters, open rebated and prepared to receive glass guage, etc. (without sash bars), edges of framing plain, chamfered or rounded. Fitted with cut and mitred beads for securing glass,etc. sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24(a); supplied and fitted to chowkhats complete all as specified and as directed by Engineer-in-charge.

S&F Butt hinges, medium weight, cold rolled mild steel --100-- mm size complete.

S&F mild steel barrel tower bolt, stove enamelled black with bright bolt of 150 mm complete.

S&F mild steel sliding door bolts plate type stove enameled black with bright bolt not less than 12 mm dia with and incl. a minimum of 6 bolts and nuts four on bolt plate and two on staple plate of 300 mm long complete all as specified and as directed by Engineer-In-Charge.

S&F MS pressed handle oval type stove enamel block with bright bolt of 150 mm. complete.

S&F brass 300 mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed by engineer-in-charge.

S&F pressed steel window (box type) factory made glaged and guaged with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded incl a prov of cooler / Ac opening with shutter including one shop coat of red oxide primer complete all specified. Note : i) The window shall be fabricated as per Drg No CEBZ/888R & 889 Sheet 1 to 4. ii) MS fillets, glazing, wire gauge shall be measured and paid separately. iii) opening incl provn shutter for cooler to be provided

S&F 3 mm Sheeet glas ordinary quality and glazing with oil putty in square n exc. 0.5 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.

M&L Galvanised stain less steel wire cloth 0.56 mm nominal dia of wire anfd averqagae width of aperature 1.18mm and fixed with tinned tracks, or galvanised wire spaples.

Do but fixed as in repairs .

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings.

S&F factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement forstyle and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site. complete all as specified.

Supply and fixing of 100 mm But hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified.

S&F steel locking bolts with mils steel electrogalvanised plate and bright bolt ont less than 10 mm dia and 100 mm size, complete all as specified .

S&F for 150mm size aluminium anodised barrel tower bolt of extruded section and fixed.all as specified and directed.

S&F for 150mm size aluminium anodised handle of febricated type and fixed.all as specified and directed.

M&L for Powder coated /anodised aluminum door window frames ,other sections for doors , windows , ventilatorswith one or more rebates , channel for sliding shutters , grills etc including jointing cleats for fixing etc , complete all as spfd .

S&F Powder coated/anodised aluminum American handle cast type 200mm for doors all as spfd...

S&F Powder coated/anodised aluminum handle cast type 100mm collapsible type all as spfd...

S&F Powder coated/anodised 75mm size butt hinges , extruded aluminum alloy ISI marked all as spfd..

Supply only rubber gasket for fixing of glass all as spfd.

S&F aluminum door closer ( aluminum extruded section) hydraullically regulated , designation No 3 , universal type , suitable for door shutters of 851mm to 1000 in width and of weight 61 to 80 kg all as spfd...

S&F doble action floor spring hydraullically regulated made up to 1.25 mm thick aluminum alloy sheet foundation box , main body with stain less steel cover , governing pivot made of brass other parts made of steel heavy duty in old or new position.(Make : Sandhu/ HI-Teck/Smart or add app by Eng-in-Charge

S&F aluminum alloy wire cloth , 0.45 mm nominal dia of wire and avg width of aperture 1.40mm and fixed with aluminum stapples all as spfd..

S&F brass mortice lock four levers (Harrisons) vetrical type size 100mm or above as directed by Eng-in -charge.

M&L for taking down old aluminum shutters and refixing the same after reairing with and including all necessary material.

M&L for rotational moulded polyethylene water storage tank ISI marked double layered (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 500 litres including all accessories, all as specified.

M&L for rotational moulded polyethylene water storage tank ISI marked double layered ,(cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 litres including all accessories, all as specified.

S&F Ball valve high pressure of PTMT with epoxy coated almn rod and high density plastic ball screwed for iron pipe and fixed fixed in repair.of 20mm Make : Prayag or equivalent.

M&L vitreous china squatting pan, orissa pattern sise 580x440mm white with integral foot rest (excluding flushing cistern) including vitreous china ‘P’ or ‘S’ traps connection to trap and to flushing pipe to complete lived in repairs and making good to floor complete.

S&F Viterous china wash down water closet pan pan (pedestal pattern ), white (excluding flushing cistern , flush pipe.(Make: CERA,Perryware,Hindware)

S&F pvc white seat cover incl all necessary hinges

S&F wash hand basin vitreous china size 550x400mm white flat back as approved by GE ,waste,chain plug,pvc connection, pvc waste pipe comp all as specified fixed in repair

S&F PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe, complete as in repairs .

Fixing only Flushing cistern after repairing the old one retrieved from repair work .

S&F in repairs bib taps cast copper alloy chromium plated fancy type 15mm bore with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F in repairs pillar taps cast copper alloy with capstan head, chromium plated, screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

S&F Stop valve cast copper alloy(concealed type) with crutch or butter fly handle screwed both ends & screwed for iron pipe of 15mm dia fixed in repair.

S&F Angle valves, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down high pressure, screwed both ends for 15 mm bore dia iron pipe or for union, ISI marked, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 32/40 mm dia PVC waste pipe for WHB/sink complete all as specified .(Min weight 45 to 60 gms .

S&F tube medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floor bore of pipe 15 mm .

S&F tube medium grade galvanized with all fitting and fixed complete to walls and ceiling or laid in floor bore of pipe 20 mm .

S&F Pvc connection 15mm size with PTMT nuts of length 450mm.

S&F PVC(SWR)single socketed in any length with rubber ring joint 110mm laid in trenches

S&F PVC(SWR)single socketed in any length with rubber ring joint 75 mm Laid in trenches .

S&F PVC SWR branch piece single equal or unequal 110mm

S&F PVC(SWR) bends any radius 110mm.

S&F PVC(SWR) bends any radius 75 mm.

S&F PVC(SWR) reducer socket bends any radius 100 mm.

S&F PVC(SWR)Cowl 75 mm.

M&L for prep of new plastered and unplastered surfaces of walls by applying upto 3 mm thick thin layer of Birla white putty to give uniform surface applying two coats of oil bound distamper on walls old decorated surfaces of desired finish as app by Eng-in-charge in any position

M&L Complete removal of existing treatment of walls and applying two coats of oil bound distemper over a thin coat of wall care putty complete all as specified and as directed by Engineer-in-Charge.

M&L applying one coat of oil bound distemper on old decorated surfaces complete all as specified and as directed by Engineer-in-Charge.

M&L for prep of new plastered and unplastered surfaces of walls and applying two coat of Cement Base Paint on walls oover a coat of priming paint as per manufacturer's instructions by Eng-in-charge in any position

M&L for prepeartion old surfaces of walls and applying one coat of cement based paint complete all as specified and as directed by Engineer-in-Charge.

M&L for three coats of white wash on newly plastered walls surfaces including preparation of surfaces.

Do but one coat on old decorated surfaces.

Ditto but on ceiling .

M&L Preparing new surface of steel of any desc over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer

M&L Preparing old surface of steel of any desc over 10cm width or girth and applying one coat of synthetic enamel paint

M&L for preparation of steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint on prepared surfaces all as specified.

M&L for two coats of synthetic enamel paint on new wooden surfaces incl prep over a coat of pink primmer.

M&L for one coat of synthetic enamel paint on old wooden surfaces .

Taking down shutters exc 1 Sqm and n exc 2 Sqm & removing to stores.

M&L Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified size of frame 105 x 60 mm including a shop coat of red oxide zinc chrome primer.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section in framed work.

GS BUILDERS AND ENGINEERS

N.K. CONSTRUCTION COMPANY

M/S ASHRAFI CONSTRUCTION CO