CA NO. GE AF NO.1/GUR-72/2023-24 REPAIR TO SECURITY/COMPOUND WALL, PATH, RAIN WATER HARVESTING PIT, AREA DRAIN, FENCING, CULVERT ETC AT AF STN GURGAON UNDER GE (AF) GURGAON NO.1

Amount

Demolition of brick work built in cement mortar including all quoins, arches, pillars, etc. of any descriptions, complete all as specified and as directed.

Taking down cement plaster, any description on brick walls or on concrete surfaces including raking out joints, hacking for key, scrubbing down with water, etc., and removing same from the site(s), complete all as specified and as directed.

M&L for plain cement concrete 1:4:8 type D-2 using 40mm graded aggregate as in foundation, filling and mass concrete complete all as specified and directed by Engr-in-Charge.

M&L for reinforced cement concrete (nominal mix), 1:1.5:3, A-1 using 20mm graded crushed stone aggregates as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete including necessary formwork complete all as specified and directed by Engr-in-Charge.

M&L for reinforced cement concrete (nominal mix) 1:1.5:3, A-1 using 20mm graded crushed stone aggregates as in columns, pillars, piers, posts and struts including necessary formwork complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in as in coping cill, rounded or chamffered on edges including necessary formwork complete all as specified and directed by Engr in Charge.

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L TMT steel bars 6mm to 8mm dia and over cut to length bent shape required, including cranking bending binding with mild steel wire (annealed) not less than 0.9mm dia quality conforming to relevant IS complete all as specified and directed.

M&L for Brick work with sub-Class ‘B’ bricks (with old size bricks), straight or curved on plan exc. 6m mean radius, built in cement mortar 1:6, complete all as specified and as directed.

M&L for Rendering 15mm thick on vertical surfaces of brick wall in cement mortar 1:4, finished plastered surfaces even and smooth without using extra cement, complete all as specified and as directed. (Note:- WPC required shall be measured and paid separetly as supply only rate under respective item of Schedule)

Excavation in post holes n exc 0.5 cum each, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, ramming and removing surplus soil to a distance n exc 50 m and making good surface for soft/loose soil, completed all as specified as directed.

M&L for plain cement concrete 1:3:6 type C-2 using 40mm graded aggregate as in foundation, filling and mass concrete complete all as specified and directed by Engr-in-Charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed by Engr-in-Charge.

S&F for MS as in posts and struts in fencing angle including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing with mesh etc including all necessary drilling bolting or riveting etc and similar work confirming to Fe-290 (Gde-E-165 quality-B. Note:-Posts/struts of angle iron made to shape shall be welded to existing angle iron bracket of security wall, contractor shall make his own arrangement for welding for boundary wall by using gen sets or any alternative arrangement all as specified and directed by Engr-in-Charge.

S&F in repair Galvanized 2 stand Steel Barbed wire 2.00mm dia barbed with dia barbs at 75 mm spacing and straining and fixing to any type of stsnderd rails, straining bolts,including securing or tying at crossings with and provisuion of galvanised mild steel pins, etc incl taking down of existing barbed wire as directed (each line wire to be measured) complete all as specified and directed by Engr-in- Charge.

S&F in repair 950/650/450 mm dia concertina coil reinforced punched(chrome razor or blade wire with barbed top of 0.5mm thick galvanised sheet and core wire of dia 2.5mm of high tensile steel wire incuding galvanised MS staples/ Clips for tying at crossing complete including taking down of existing concertina coil all as specified and directed by Engineer–in-Charge.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long and 5 to 10mm dia all as specified and directed by Engineer–in-Charge.

M&L for preparation of new steel surface exc 10 cm in width or girth and applying two coats synthetic enamals paint over a coat of red oxide/zinc chrome primer complete all as specified as directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. in soft / loose soil complete all as specified and directed.

Removing excavated material (soil) exc 1.5 KM and not exceeding 5 KM and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

Demolition of concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

S&F 0.50 mm thick pre coated thick galvalume aluminium zink coated GI based corrougated steel sheeting of any colour having tensile strength of 550 MPA as in roof covering/glading to wall fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

Dismantling of stone slab and tiles of any description or thickness in floor laid dry complete all as specified and directed.

M&L 75mm thick plain cement concrete 1:2:4 type B-1 using 20mm graded aggregate finished even and smooth w/o using extra cement complete all as specified and directed by Engr-in-Charge.

M&L for 60 mm Machine pressed pre casted pressed cement concrete inter locking paver blocks glazed coloured up to 6mm on the top in any shape and size, strength not less than M-35 with grey cement and pigment complete all specified and directed by Engr-in-Charge.

M&L for sand filling under floors or in foundation including watering and consolidated complete all as specified and directed.

M&L for washed stone grit plaster on exterior walls in two layers under layer 12mm cement plaster 1:4 (1cement 4coarse sand) furrowingthe under layer with scratching tool applying cement slurry @ 3kg/sqm top layer 15mm cement plaster 1:1/2:2 ( 1white cement 1/2 coarse sand : 2 stone chipping coloured 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing & washing the top layer with brushes & water to expose the stone chipping complete all as speacified pattern decided by Engr-in-Charge.(payment for providing grooves shall be made separately). Note:- Top layer of shade be of white cement using colouring pigment & stone chipping of desired colour as approved.

M&L for Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge

M&L one coat of red oxide two coat of aluminium paint including preparation of old steel surface exe 10cm width or girth, complete all as specified and directed by Engr-in-Charge

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and directed by Engr-in-Charge

M&L for cleaning/ desilting of existing bed of the drains constructed in any masonry, average thickness not exceeding 10cm including removal of vegetarians, growth or bushes, roots and getting out including disposing off excavated silt, soil, vegetarians, shrubs etc 1.5 km to 5.00 km above the starting point complete all as specified and directed

M&L providing, precast cement concrete 1:2:4, type B-1 using 20mm graded crushed stone aggregates in cover slabs (for manholes etc) chullah hoods, chajjas, water troughts, mangers, shelves and similar articles with plain faces and setting in cement mortar 1:4 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles from site and rubbish off the premises complete all as specified and directed.

Rounding to edge of stone slabs one edge such as steps, cooking platform and similar situation complete all as specified and directed.

M&L 18 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20mm thick screed bed or bedding payer in cement mortar 1:6 complete all as specified and as directed.

M&L for aluminium composite panel 4mm thick in multiple colours to fixing with screws at columns, fascia, and ceiling with silicon is used for good looking , fixed as in repair complete all as specified and as directed. Note: The work is to be carried out at any height of all etc. Necessary T&P, scaffolding, to carry out the above work is also included in quoted rate, complete all as specified and directed.

M&L chequered cement concrete tiles 20mm x 25mm thick, set jointed and pointed in nexe cement slurry in floors with gray cement and pigments including 20mm thick screed bed or bedding layer in layer in cement mortar 1:6 complete all as specified and as directed

Note :- The amount of Rs 2,18,000/- against Schedule of Credit on Srl Page 130 shall be deducted from the total amount quoted against Sch 'A'

NAVYUG VYAPARI

shakti construction

Phogat Builders

MOHIT ENTERPRISES

Dhirendra Singh & Sons

J M V D Enterprises