Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹2.8 LAccepted-Finance | L1 | Accepted-Finance First lowest | |
| 2 | L2₹2.9 L+₹6,085 (2.18%)Accepted-Finance | L2 | Accepted-Finance Second lowest |
Tender Value
Refer Docs
EMD Value
₹5,164
Closing Date
26 Mar 2024, 6:00 pmClosed
Executive Engineer Civil
Executive Engineer Civil BSNL Civil Division 3rd Floor Telephone Bhawan Shaheed Chowk Ranchi
Construction of E A Shed in T E Campus at Ranchi
2024_BSNL_191901_1
69/NIT/EE(C)/BCD/ RCH/2023-24
Open Tender
Civil Works
Item Rate
30 days
T E Campus Ranchi
Please refer Tender documents.
4 documents required · 4 mandatory
₹590
Accounts officer Cash Olo the GMTD BSNL Ranchi
₹5,164
30 Mar 2024
19 Mar 2024
28 Mar 2024
19 Mar 2024
26 Mar 2024
19 Mar 2024
Amount
SH: EARTH WORK
Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.
All kinds of soil.
SH: CONCRETE WORK
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to V level:
1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
SH: STEEL WORK
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete
Hot finished welded type tubes
Providing and fixing bolts including nuts and washers complete.
SH: ROOFING
Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
Extra for providing and fixing wind ties of 40x 6 mm flat iron section.
SH: FINISHING
Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:
Two or more coats on new work
SH: DISMANTLING & DEMOLISHING
Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.
Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)
DINESH KUMAR SINGH
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .