SPECIAL REPAIR TO BLDG NO P-378 AND P-379 (OTM ACCN) AT UDAIPUR MIL STN

Amount

Demolition of cement concrete(unreinforced) of any description and in any position not otherwise specially provided for not exceeding 15cm thickness below or above ground level and removing material from site complete all as specified and directed.

Taking down wooden chowkats or frames area not exceeding 1.50 Sqm (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1, complete all as specified and as directed. (Note – The quoted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts and no separate item for making good of hold fasts shall be paid).

Taking down wooden chowkats or frames area exceeding 1.50 Square metre and not exceeding 4.00 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes for taking out existing hold fasts and making good in cement mortar (1:3) or PCC 1:2:4 type B1, complete all as specified and as directed. (Note – The qouted rate shall be deemed to include for fixing of hold fast in the same opening irrespective of position of hold fasts and no separate item for making good of hold fasts shall be paid).

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

Material and Labour glazed ceramic light coloured tiles in vertical serfaces 600 x 300 x 7-8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces as backing for tiles, complete all as specified and directed.

Material and Labour for non skid ceramic light colored jointless tiles of Size 400mm x 400mm x 6-8mm thick as in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Material and Labour 40mm thick PCC as in floor type B-1, (1:2:4) using 20mm graded stone aggregate rough Finished complete all as specified.

Material and Labour for double charged vitrified light coloured tiles 600mm x 600mm x 8-10mm thick polished, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM (1:4), complete all as specified.

Supply and fixing double charged vitrifiedlight coloured tiles 600mm x 100mm, 8-10mm thick as in skriting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster in CM (1:4), complete all as specified.

Material & Labour for Udaipur Green Marble work 16 to 18 mm thick (table rubbed and polished) in steps, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade and including 10mm thick screed bed in CM 1:6 set and jointed in neat cement slurry complete all as specified and directed.

Material and Labour 16-18 mm thick Granite south black (Z/Telephonoc black) work (table rubbed and polished) in cooking platforms and like in CM(1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick Screed in CM (1:4) complete all as specified and directed.

Material and labour for 50mm thick, PCC 1:3:6 type C-1 (using 20 mm graded mechanically crushed stone aggregate) as in plinth protection/PCC path, and paving, finished the surface even and fair without using extra cement, laid in alternate bays, complete all as specified.Note : Joints 12 mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

Supply and fixing PVC low level flushing cistern of 10 ltr capacity, valveless syphonic action type complete with inlet ball valve float valve bends brackets all as required incl taking down existing high level/low level flushing cistern any type disconnecting pipes and jointing with new one etc and making good the floors/walls as per existing floor finish/wall finish including 32 mm bore PVC flush pipe and jointing with Water closet of any type complete all as specified and directed. (Make-Cera/Hindware/Parryware/Pryag)

Supply and fixing vitreous china wash basin white flat back size 550 x 400mm with pedestal excluding taps, waste, chain & plug and porcelain stopper but including brackets or fixed to walls with anchor fastners all as specified and directed. (Make-Cera/Hindware/Parryware/Pryag)

Supply and fixed in repair, vitreous China squatting pan of Orrisa pattern size 580mmx440mm white (Ist quality) with ‘P’ or ’S’ trap, front or back inlet and integral foot rests of any pattern complete including provision of lime concrete bedding, trap and connection to flush pipe complete all as specified. (Make-Cera/Hindware/Parryware/Pryag)

Supply and fixing Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe). (Make-Cera/Hindware/Parryware/Pryag)

Supply and fixing Plastic water closet seat, white closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device all as specified and directed by Engr-in-charge. (Make-Cera/Hindware/Parryware/Pryag)

Supply and fixing CP jet spray with flexible tube etc complete all as specified & directed. (Make-Cera/Essco/Coronet/Prayag)

Supply and fixing in repair 15mm bore 2 way angle valves cast copper alloy screwed down high pressure with crutch or butter fly handles screwed both ends for iron pipe or for union all as specified and directed by Engr-in-charge. (Make-Cera/Essco/Coronet/Prayag)

Supply & fixed in repair fancy type shower rose125mm dia size of Rim and 30cm long CP brass pipe with swiwel joint complete all as specified. (Make-Cera/Essco/Coronet/Prayag)

Supply and fixed in repairs,15mm bore pillar tap, fancy type, chromium plated cast copper alloy with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks , compete all as specified. (Make-Cera/Essco/Coronet/Prayag)

Supply and fixing in repair, bib tap screwed down high pressure, cast copper alloy,fancy type, chromium plated, ISI marked, with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified. (Make-Cera/Essco/Coronet/Prayag)

Taking up or down 15mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connections by disconnecting fittings/tubing from existing tubing were required including cleaning for refixing or removal from site complete all as specified and directed.

Supply & fixed GI tubing medium grade 15mm dia incl fittings, cutting threading and fixing to walls or fixing in concealed walls or in floors etc, and making good the surfaces matching to exsiting surafaces of walls/ floor to the entire satisfaction of Engineer-in-charge.

Description all as per Srl item No.26 here in before but 20mm complete all as specified.

Supply and fixed (in repair) stop/angle valves, 15 mm dia pipe, chromium plated, ISI marked, screwed down, high pressure with crutch or butterfly handle (concealed type) with long shank, screwed both ends for iron pipes or for unions, complete all as specified. (Make-Cera/Essco/Coronet/Prayag)

Supply & fixed in repair PVC connections 45cm long including 15mm bore PTMT nuts on both ends complete all as specified. (Make-Prayag/Cera/Plumber)

Supply & fixed in repairs CP steel grating openable 100mm dia without hole including fixing with white cement complete all as specified.

Supply & fixed in repair CP brass soap tray fixed to plug with cromium plated brass screw complete all as specified. (Make-Cera/Essco/Coronet/Prayag)

Supply and fixing for mild steel framed work as in door chowkats /gate of angle or other section of grade Fe-290-Gde E-165 with gusset plate rails, braces etc welded/drilled to fixing of steel sheeting or other covering doors etc. to be prepared for sliding or hanging with and including either hooks and hinges or steel hanging door fittings (exclusive steel sheeting or other covering, running rails & guides).

Material & Labour for PCC1:3:6 type C-1 (using 20 mm graded stone aggregate) as in hold fast, back of pressed steel chowkats complete all as specified and directed.

Supply and fixing Plain framed, panelled shutter 35mm thick (two panel) with lock rail & panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. 2nd Class HW rail & style of size as per IS: 1003 (Part I), kiln seasoned & chemically pressure treated

Supply and fixing IInd class (hollock) factory made 35mm thick glazed skelton shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I), complete all as specified and directed.

Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge

Supply and fixing PVC factory made shutter solid, PVC moulded prelam coloured on both side door shutter with particle board core 28 to 30 mm thick (stiles), with 2, 4 or 6 raised panel design in framing at site as per specifications & drawings.

Supply & fixed 200 mm long aluminium anbodised barrel tower bolts of extruded section and fixed complete all as specified and directed

Supply & fixed 150 mm long Extruded aluminium alloy handles, fabricated type anodised complete all as specified.

Supply & fixed 100 mm butt hinges, medium weight cold rolled mild steel and fixed complete all as specified and directed.

Supply and fixing 200 mm mild steel barrel tower bolts, ISI marked, stove enameled black with bright bolt and fixed, complete all as specified.

Supply and fixing mild steel pressed handles, oval type, enameled black 150mm long, complete all as specified.

Supply and fixing 300 mm mild steel sliding door bolts, ISI marked, stove enameled black, with bright bolt not less than 16mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple, complete all as specified.

Supply & fixed MS helical door spring150 mm long fixed with screws to wooden chowkhats or fixed with welding to steel chowkhats.

Supply and fixing Aluminium anodised or powder coated door, window, ventilator frame with one or more rebates and shutter sliding or casement windows as reqd. including jointing cleat, glazing clips with EDP gasket for fixing, rubber packing etc, complete all as specified and directed.

Supply & fixed for anodised aluminium grill (anodised transperent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design /pattern, with approved standard section and fixed to the existing window frame with CP brass /stainless steel screw @ 200 mm centre to centre, including cutting th grill to proper opening sixe for fixing and operation of handle and fixing approved anodised aluminium standard section around th opening, a;; complete as per requirement and direction of Engineer -in - charge.

Supply & fixed steel for 5mm thick figured glass, ordinary quality and glazing rubber beading in square nexc 0.5 sqm in each pane complete.

Supply and fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staple or fixing with beads to wooden joinery when fixed in panels of joinery, complete all as specified.

Supply & fixing in repairs stainless steel type curtain rod 22 to 25mm dia as per sample as in repair including stainless steel decorative fincals, brackets and wall to wall as required.

Taking down cement plaster from brick walls ,concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc complete all as specified and as directed.

Material and labour for 15mm thick rendering in cement mortar (1:6) on brick or concrete surface of any description, finished the surface even and smooth without using extra cement complete all as specified.

Material and Labour for 15mm thick rendering ontop of RCC Chajjas fair faces of brick work/concrete surfaces in cement mortar 1:4 mixed with WPC @3% by weight of cement or as per manufacturer’s instructions, finished even and fair, complete all as specified. (Note : WPC shall be measured and paid separately)

Material and labour 10 mm thick cement plaster in cement mortar 1:3 on ceiling, finished even and smooth without using extra cement all as specified and directed.

Material & Labour for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over 1mm thick wall care putty on plastered for neat and smooth finishing including preparation complete. alll as specified.

Material & Labour for preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper over 1mm thick wall care putty on plastered for neat and smooth finishing including preparation complete. alll as specified.

Material and labour for preparation of new plastered surfaces of walls and applying two coat of weather coat over a coat of Alkali resistant primer over 1mm thick putty complete all as specified.

Material and labour for complete removal of existing treatment and preparation of old Plastered or un-plastered surfaces of ceiling by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying two coats of oil bound distemper over 1mm thick wall care putty on plastered for neat and smooth finishing including preparation complete. alll as specified.

Material and labour for Preparation of old Plastered or un-plastered surfaces of walls ,cornices etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying two coat of white wash on walls complete all as specified.

Complete removal of existing treatment of wall and applying two coats of oil bound distemper over 1mm thick wall care putty on plastered for neat and smooth finishing including preparation complete. alll as specified.

Complete removal of existing treatment and applying two coat of weather coat over one coat of Alkali resistant primer over 1 mm thik putty complete all as specified.

Supply & fixed for sheet glass 3mm thick, ordinary quality and glazing with oil putty, in square n.exc 0.5 Sqm each and glazing with oil putty to steel window complete all as specified.

Material and Labour for two coat of synthetic enamel painting to wood surface of any description, not otherwise described over 10cm width or girth including preparation of new surfaces over a coat of pink primer cpmplete all as specified and directed.

Description all as per ser item No 77 herein before but on steel surface over a coat of red oxide primer complete all as specified.

Dismantling of PVC drain pipes, jointed in cement mortar and taking out complete all as specified and directed.

Supply and fixing PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors

Supply and fixing PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors

Supply and fixing PVC (SWR) bends with access door of any radius 110mm dia

Supply and fixing PVC (SWR) branch piece, single (single Y) equal or unequal 110mm dia

Supply and fixing PVC (SWR) bends with access door of any radius 75mm dia

Supply and fixing PVC (SWR) branch piece, single (single Y) equal or unequal 75mm dia

Material and labour in repairs 75mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate all as specified and directed.

Dismantling water tanks 500 to 1000 Ltrs capacity (Steel/AC/RCC tanks) & removing from site all as specified.

Supply & Fixing, Routational moulded, polythene water tank 1000 ltr capacity 3 layered (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified and directed.

Material & labour for PCC 1:2:4 type B-1 (using 20mm graded mechanically crushed stone aggregate) as in coping & bed blocks, side of interlocking tiles etc complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specially provided for including cutting of steel reinforcement as required to facilitate demolition, complete all as specified.

Supply only liquid water proofing compound, ISI marked complete all as specified and directed.

Material and labour Preparation of old painted wood or wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint of approved shade & quality complete all as specified and directed.

Material and labour Preparation of old painted steel or iron based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint of approved shade & quality complete all as specified and directed.

Material and labour for providing reinforced cement concrete 1:2 :4 type B1 using (20mm graded stone aggregate ) as in slab supported on wall, beam and kitchen cooking platform complete all as specified.

Material and labour mild steel TMT bars, 8 mm dia , cut to length, bent to shape required including cranking, binding spirally for hooping or column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

Dismantling of brick work or stone masonary, precast cement concrete walling built in cement mortar including all quoins, arches, pillars etc., complete all as specified.

Material and labour for brick work with sub class ‘B’ bricks, locally known as “Awwal” straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6), complete all as specified.

Material & Labour for brickwork with subclass 'B' brick to any radious in half brick thick in CM 1:4 complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs any thickness, including cover fillets complete all as specified.

Supply and Fixed suspended false ceiling system using Chicago metallic (E - grid) exposed suspended system, grid size 600mm x 600mm comprising of GI powder coated Main Runner of dimensions 39mm x 24mm x 0.8 mm thick (Thickness comprising of GI/0.4 mm+ PPPCGS/0.3 mm & weight of runner 1.35 kg for 3600 mm length), Cross Tee of dimensions 29mm x 24mm x 0.8mm thick (Thickness comprising of GI/0.4mm + PPPCGS/0.3mm & weight of Tee 0.195 kg for 600mm length) and Wall angle of dimensions 22.2mm x 22.2mm x 0.65mm thick (Thickness comprising of GI / 0.35mm + PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length) with and including 6mm thick HPSC (High pressure steam cured) pre primed, self embossed, textured designer board to be placed in the grid system duly suspended with 4mm dia GI wire hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt-0.007 kg/clip), hold down clips (wt-0.0035 kg/clip), with provn of light fixture complete all as per manufacturer instructions and as directed.

Material & Labour 18/19mm thick block board, grade 2 quality interior grade, commercial type fixed with screw to timber frame work including taking down complete all as specified and directed.

Material & Labour Decorative laminate type 1 of 0.9 mm thick surface finish, colour and pattern as approved, fixed with approved adhesive as manufacturer's complete all as specified and directed.

Supply & fixed Continious piano hinges, continuous type of mild steel bright finish or electro galvanized with width of flap (when open) 30mm complete all as specified.

Supply & fixed 75mm long stainless steel handle fixed with nut and screws to cupboard shutter complete all as specified and directed.

Supply & fixed magnetic ball catches with 8mm dia steel ball brass body and striking plate including letting in and fixed, overall length of cover plate 140mm long complete all as specified

Demolition cement concrete in any position not other wise specifically provided for complete all as specified

Material and Labour for PCC 1:2:4 type B-0 using (12.5 mm graded stone aggregate) as in padding on roof top including WPC as per manufacturers instructions to achieve the slop required and finished even and fair without using extra cement. (WPC shall be measured and paid separately

Material and Labour for 10 mm thick screed bed or bedding layer in CM 1:3 mixed with water proofing compound as per manufacturer instructions on concrete roof surface finished fair and even to maintain the proper slope of roof surface etc complete all as specified and directed.

Material and Labour for Providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing memberane comprising of the following for Non Approachable roofs-

(a) Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.30 kg/Sqm on top of dry surface of finished cement mortar plaster.

(b) One coat of hot blown bitumen of grade 85/25 @ 1.2kg /sqm shall be applied over primed surfaces.

(c) One layer of polymeric water proofing membrane of weight not less than 3 kg/Sqm consisting 90 micron thicken of central core shall be unrolled surfaces with lap of 100 mm and the over lap shall be sealed by flame.

(d) Applying two coats of aluminum paint on top of membrane @ 0.10Kg/Sqm.

Supply & Fixed in repairs 20mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed.

Supply & Fixed in repairs 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed. (Make-Leader/ Zoloto/ Sant)

Supply and fixing coloured Vetrified Ceramic tiles 600mm x 600mm, 8-10mm thick (square/rectangular) polished, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM(1:4), complete all as specified.

Supply and fixing coloured Vetrified Ceramic tiles 600mm x 600mm, 8-10mm thick (square/rectangular) as in skriting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster in CM(1:4), complete all as specified.

Supply & fixed in repairs stainless steel sink with drainage board , made out of 1.00mm thick sheet for kitchen oe laboratory with plug,washers, waste pipe, cast irn cantilever bracket of overall size 1040x510x203mm bowl size 510x405x203mm including waste pipe, coupling etc, complete all as specified.

Supply and fixing ball bearing slide length 17 " width 46mm and 12mm thick complete all as specified and directed (for measurement length shall be measured in close position) (Make: Haffle/Godrej/Hettich)

Supply and fixing beading 1st class soft wood of cross sectional area area 19mmx3mm fixed with the help of head less nails duty polished complete all as specified.

Supply and fixing for PCC coloured interlocking (glossy finishing) paver blocks confirming to IS-15658-2006 of 80 mm thickness, M-40 grade as in hardstanding etc. laid over and including 40 mm thick screed or bedding layer of sand, complete all as specified.

Material and Labour PCC type C2 (1:4:8) using 40 mm graded stone aggregate as in sub base/mass concrete and finished the top surface even and fair without using extra cement complete all as specified.

Material and Labour for Vitrified out door tiles 40 cm x 40 cm x 10 mm thick digital design set, jointed and pointed in neat cement slurry as in floors with grey cement over & including over screed bed or bedding layer of mortar 20 mm thick Cement Mortar 1:6. (Make-H & R Johnson, Brand-Endura digital designer series or equivalent)

Supply and fixing Polyester plain or coloured large size vertical Venetian Blinds office windows, solid pattern back tab type slats or vanes width 75 mm to 125 mm and minimum window widht 1.5 mtr.

Removing building materials etc. to a distance of 1.5 KM or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination.

Taking down old unserviceable copper/aluminium point wiring (light, fan, socket or power) complete including fittings and fixtures such as switches, ceiling rose, pendants, regulators, sockets, light fitting etc. and making good disturbed surfaces of walls, floors, etc. all as directed by engineer in charge.

Material and Labour for point wiring with 1.5 Sqmm multistranded,1100 volt grade copper conductor cable of PVC insulated, FRLS and unsheathed type alongwith 1.5 Sqmm PVC insulated stranded copper conductor cable for continous earthing in & including PVC rigid conduit concealed with accessories having ISI mark fixed on wall surfaces / ceiling including provision of PVC box of appropriate size for fixing switches sockets etc. all as specified (Make of cable: Kalinga/Havells/Anchor)for One light point / Fan/ bell point controlled by one switch.

(a) One light point controlled by one 5 Amps switch

(b) One Fan/exhaust fan point controlled by one 5 Amps switch

(d) One socket 3 Pin 5A pin socket oulet 5Amps on same board with cables 1.5 Sqmm size

(e) One socket 3 Pin 5A pin socket oulet 5Amps on indepndent board with cables 1.5 Sqmm size.

(f) One socket 3 Pin 15A pin socket oulet 15Amps on indepndent board with cables 4 Sqmm size

Supply and fixing switch piano flush type single pole one way 5/6 Amps. Make : Anchor / Leader/ Kinjal.

Supply and fixing stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd. Make : Anchor / Leader/ Kinjal.

Supply and fixing lamp holder Angle / batton type insulated body with back plate and to be fixed on PVC bock. Including dismantling old one. Make : Anchor / Leader/ Kinjal.

Supply and fixing socket outlet 5 pin 5/6 Amps flush type multipurpose suitable for 3 pin/2 pin plug complete including dismantling old one. Make : Anchor / Leader/ Kinjal.

Supply and fixing of switch piano15 Amp 230 Volt, flush button single pole one way complete all as specified and directed by Engr-in-Charge including dismantling old one. Make : Anchor / Leader/ Kinjal.

Supply and fixing socket outlet 2 in 1, 3 pin 5/6 Amps and 3 pin 15/16 Amps flush type including old one. Make : Anchor / Leader/ Kinjal.

Supply and fixing ceiling rose surface tpe 3 terminals to be fixed on PVC block including dismantling old one. Make : Anchor / Leader/ Kinjal.

Supply and fixing LED integrated batten tube light fittings 20/22 Watt 4 Feet long complete up with twin core twisted flexible copper conductor cable of size 23/0.0076 complete all as specfied and directed. Make Havells/CG/ Phillips

Taking down old Sheet metal/wooden enclouser and supply and fix new sheet metal enclouser cubical type factory fabricated made out of 1.6 mm thick CRCA sheet with front side openable single door system powder coated painted to shade RAL 7032, PL Gasket, hinged single door ,IP-55 mounting plate made out of 2mm thick CRCA sheet steel and earth bolts etc. of size 600x500x200mm all as speceified & directed by Engr-in- charge. Make : Havells / Legrand / Schneider/Standard. Note :-- Cost of any minor modification if required in fixing of the sheet metal enclouser as per site requirement and making good the disturbed surfaces matching with existing finish, will be deemed to be included in the cost of this item.

Material and Labour MCB SPN DB sheet metal enclosure double door suitable for mounting MCB 240 Volts with busbar 8 way including dismantling old one. Make : Havells / Legrand / Schneider/Standard

Supply and fixing MCB TPN 415 Volts 63 Amps. Make : Havells/Legrand/Standard/ C&S

Supply and fixing MCB SPN 230 Volts 32 Amps. Make : Havells/Legrand/Standard/ C&S

Supply and fixing MCB SP 230 Volts 6- 32 Amps. Make : Havells/Legrand/Standard/ C&S

Dismantling carefully ceiling fans of size 1200 mm sweep of any make and cleaning, oiling, greasing, painting with exinsting colour, replacement of fan clamp, refixing including provision of cable from ceiling rose or connector to fan and testing all as specified and directed by Engr-in-Charge.

Taking down old exhaust fan, depisited into MES store and Supply and fixing exhaust fans AC single phase 230/240Volts of size 300 mm sweep with louver and complete accessories, including making hole with suitable size for Exhaust Fan, tightend with required nut, bolt, washers etc, after completion of work, finishing with cement and plastering and repainting with exisitng color all as specified and directed by Engr-in-charge.

Material & labour for earthing complete with galvanised steel earth plate electrode 60x60cmx6.0 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below the ground level) with top edge of the plate not less than 1.5 mtrs below normal ground level, connected to galvanised earth wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or of steel all as shown in electrical plate No 3 of SSR part-I 2009 connected to main switch board all as specified and testing on completion including. Necessary excavation, earthwork, PCC works and CI earth pit cover with watering pipe 20mm dia GI pipe medium grade, funnel with wire mesh and lugs and GI pipe 15 mm dia of light grade, for protection of earth lead complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5core.

Supply, laying and testing cable XLPE Insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 6 sqmm 4 core.

Excavating in trenches n.exc 1.5 m width and n.exc 1.5m in depth for taking out cable and cable cover and getting out in any type of soil

Returning, filling in, including spreading levelling, watering and well ramming in layers n.exc 25 Cm

Removing excavated materials n.exc 50 mtr depositing where directed at a level n.exc 1.5m above the starting point

Material and Labour for sand cushioning to PVC/ XLPE cables with tibba sand and punning to provide required cover to UG cables. Note :- For the purpose of payment only punned thickness will be measured.

Material and labour for stone slab ( patti) roughly hammer dressed stone 25 to 35 mm thick 25 to 30 cm wide and not less than 60 cm long laid dry and abutting each other with gap between adjacem,ent salb not exceeding 10 mm over underground cables for protection.

Taking out old unserviceable protection Pipe and supply and fix light grade 50 mm dia GI pipe fix complete to Wall, Poles etc with suitable clamp for protection of cable complete all as directed

Taking out old unserviceable protection Pipe and supply and fix light grade 40 mm dia GI pipe fix complete to Wall, Poles etc with suitable clamp for protection of cable complete all as directed

Taking down of window/split type A/C, depposited into store and refixing including washing and cleaning of cooling coil, condenser with caustic soda. Replacement of air filter, oiling of fan motor, checking, testing and refixing the same after replacing the air filter all as directed.

Supply and fixing Submain wiring in PVC Coonduit alongwith earth wire with the following sizes of 2x2.5 sqmm + 1x1.5 sqmm FR PVC insulated copper conductor, single core cable in surface/recessed as required.

Supply and fixing Submain wiring in PVC Conduit alongwith earth wire with the following sizes of 2x 4.0 sqmm + 1.25 sqm FR PVC insulated copper conductor, single core cable in surface/recessed as required.

L AND J CONSTRUCTION CO.

M/s SUNIL ENTERPRISES

M/s Ajay kumar Garge