8148 CONSTR OF TOILETS AND BATH AT SC STY DEPOT FOR ACCOMMODAION OF 41 ARTY DIV PRO UNIT ADDN ALTN TO BLDG NO P 61 MI ROOM SPECIAL REPAIRS TO BLDG NO ET 28 AT AFSMC AND CERTAIN MINOR WORKS UNDER GE CENTRAL PUNE

Amount

Demolition of brick masonry built in cement mortar including all quoins, arches, pillars etc all as specified and directed and removing rubbish of the premises complete.

Dismantling of asbestos cement (corrugated, semi corrugated etc) sheets in roof covering and removing from site of work complete all as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exc. 1.50 Sqm and n exc 4.0 Sqm each and removal from site complete all as directed.

Taking down cement plaster on brick of stone walls of concrete surfaces etc incl racking out joints, hacking for key, scrubbing down with water etc and removing rubbish off the premisses complete all as directed.

Surface excavation n exc 30 cm deep and averaging 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

Rough excavation not exc 1.5 m deep and getting out in soft/loose soil complete all as specified and directed.

Excavation over area n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed.

Excavating in trenches n exc 1.5 m wide and n exc 1.5 m in depth, for foundation etc or for shafts wells, cesspits, manholes, pier holes, etc n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Removing excavated soil exc 250 metre but n exc 500 metre and depositing where directed at a level n exc 1.5m above the starting point.

Removing excavated soil exc 1.50 Km. & n exc 5 km & depositing out side of MoD Land complete all as specified and directed.

M & L for hard core of gauge exc 63 mm but not exc 100mm using broken stone or boulders deposited spread levelled not exc 15 cm thick watered and rammed to true surfaces complete all as specified and directed.

M & L for sand filling under floor under interlocking tiles including watering and consolidation complete all as specified and directed.

M&L for loose filling with broken bricks of gauge 80 to 150 mm in soakage pits complete all as specfied and directed.

M & L for PCC 1:4:8 type D2(using 40 mm graded stone aggregate) in foundation complete all as specified and directed.

All as per item No 15 here-in-before but PCC(1:3:6) type C2.

M & L for PCC (1:3:6) type C1 using 20mm graded agg. for fixing of hold fasts etc including necessary formwork complete all as specified and directed.

M & L for PCC 1:2:4 type B1 using 20 mm graded aggregate as in benching of manhole complete all as specified and directed.

M & L for PCC 1:2:4 type B0 using 12.5 mm aggregate as in coping of manhole including necessary formwork and kerb in interlocking tiles complete all as specified and directed.

M & L for precast RCC cover slab using 1:2:4 type B1 (20 mm graded aggregate) and set in CM 1:4 complete all as specified and directed.

M& L RCC Design mix M- 25 (using 20 mm graded stone aggregate) for Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

All as per item no 21 here-in-before but for Beams, cantilevers, bessummers, lintels over 1.5m span etc.

All as per item No 21 here-in-before but for columns, pillars, piers, posts and struts.

M&L for precast cement concrete block masonry exceeding 10cm in width with solid blocks of PCC (1:5:8) gde C-5 and setting in CM 1:6 complete all as specified and directed.

Cutting openings through walls for door, windows and othr openings or enalrging existing openings, etc or cutting out defective masonry for underpinning including providing fixing and removing, shoring, cleaning and removing rubbish off the premises complete all as directed.

Cutting holes in brick wall, built in CM for inserting hold fast and making good dismantled portion in CM 1:3 depth of embedded portion of hold fast or lugs measured from the face of the jamb into the wall etc. half brick but n exc one brick thick complete all as specified and directed.

Cutting chases, pinning in making good to facings where required and pointing in CM 1:4 for concealed water tubing etc complete all as specified and directed.

M & L for damp proof course 40mm thk to horizontal or vertical surfaces in cement concrete 1:2:4 type B-0 with WPC as per manufacturer’s instructions including necessary formwork complete all as specified and directed. Note : WPC shall be measured and paid separately.

Use and waste of formwork to sides of rough finished surface of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter.

All as per item No 29 here-in-before but to sides of pillars, posts, struts, piers, columns and stanchions.

All as per item No 29 here-in-before but to sides and soffits of roof beam, lintels etc. including supports,overhangs and also splays between floors and beams.

S&F plain, framed, panelled shutters, 2nd class hard wood, 30mm thick (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, suppliedd and fitted to chowkats as specified and directed by Engr-in -Charge.

S & F solid PVC door frame of size 50mm x47mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC sheet and edges will be painted to match with prelam sheet reinforced with MS square tube, supplying and fixing in opening all as specified and directed.

S & F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face all as specified and directed.

S & F butt hinges 100mm size MS cold rolled medium weight all as specified and directed.

M & L Mild steel barrel tower bolts, 200 mm long stove enamelled black, with bright bolt and fixed complete all as specified and directed.

M & L Mild steel pressed handles,150 mm long oval type, stove enamelled black complete all as specified and directed.

M & L Mild steel sliding door bolt 300mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed.

S & F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M & L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) 0.9mm dia or securing with clips quality complete all as specified and directed.

All as per item No 40 here-in-before but 5mm dia and over upto and including 10mm dia in stirrups, spaces and binders.

M & L for rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle leats or other connecting plates complete all as specified and directed.

M & L mild steel rolled section as in joist, channel, angle, rafter, purlins or tee sections, fixed independently, without connecting plates etc (cut to ordinary lenghs i.e within 20mm of the length indicated) complete all as specified and directed.

S & F MS work in small articles such as hold fast etc. all as specified and directed.

M & L 125 mm x 60 mm with 1.2 mm thick (PBI sheet with PCC 1:3:6 filling in inner core of frame) Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

S & F ventiltors/ louvers with partially guaged shutter using 5 mm thick x 10 cm wide frosted glass strips and following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make and rubber beading etc all as directed. (a) SP 20048 (b) Glazing clips 19352

S & F powder coated three track sliding window with two or more shutter witth 4 mm thick tinted glass , one shutter of stainless steel wire cloth 0.36 mm nominal dia & 1.18 mm width aperture for mosquito proofing with good quality bearing, handle lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified directed by Engr-in-Charge. (a) Bottom frame 20620 (b) Top frame & Verrtical 20621 (c) Handle (side) 20606 (d) Shutter inter lock 20724 (e) Shutter top & Bottom 20844 (f) Glazing Clip 19352

S & F powder caoted anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complee all as specified and directed.

S & F Aluminum single leaf door on pivst of powder coated frames alongwith hydrulic door closer (Aluminium Extruded section), door lock, handles, 5mm thick tinted glass in top and 12mm thick prelaminated particle board (both side laminated) in bottom panel, fixed with rubber beading and glazing clips using 'JINDAL, Catalogue complete all as directed by Engineer-in-Charge.

S & F stainless steel angle flat square or rectangular pipe in railing (grade 304-316 corrosion resistance) with ornamental and intericate design complete.

S & F Pre painted galvalume aluminium zinc coating GI based plain profil sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering /clading to wall fixed with self taping screws all as specified and directed.

All as per item No 51 here-in-before but plain sheet on ridges.

M & L for false ceiling with 8 mm thick PVC panels (coloured/designed) including decorative comices/ moulding of pattern as per approved by Engr-in-Charge on GI grid frame work consisting grid & GI main tee 32 x 24 mm, cross tee 25x24 mm and angle of walls of size if grid not less than 600x 600 mm hung from ceiling using 2 mm GI wire suspendors spacers at 1.2 mtrs c/c on main runners including making nitches for light, fan decorative/concealed light fittings and fasteners if required complete all as specified and directed.

M & L for Gypsum ceiling board for ceiling prepainted, perforated finish, 600 x 600 x 9 to 9.5mm thick in size, of approved brand/make, laid over and including grid work of size 600 x 600mm, made out of 0.5mm thick G.I tee 32 x 24 mm for main, 25x25mm for cross tee and 20 x 20mm angle fixed on wall, powder coated finish on exposed faces of tee and angle, hung from ceiling using 2mm thick G.I Suspension wires spaced at 1200 mm on main runners including making niches or fans/light at as specified and directed.

M & L for PCC 1:4:8 type D2(using 40 mm graded stone aggregate) 100 mm thick and finishing cement conc. surface in sub base complete all as specified and directed.

M & L 75 mm thick PCC 1:3:6 type C2 ( using 40 mm graded stone aggregate) as in plinth protection/ path etc finished even and smooth without using extra cement complete all as specified and directed.

M & L for PCC 1:2:4 type BO (12.5 mm graded aggregate) 25 mm thick and finishing the surface even and smooth with using extra cement for floor finishing of the tank complete all as specified and directed.

M & L for PCC (1:2:4) type B0 25mm thick (12.5 mm graded aggregate) in floor to receive top layer like tiles etc complete all as specified and directed.

M & L for non skid coloured ceramic tiles (of any colour) flooring 7 to 8 mm thick, area of each tile exceeding 0.11 sqm and not exc 0.18 sqm with joint free tiles set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15mm thick cement screed bed in CM 1:6 complete all as specified and directed.

M & L for 450 x 300 x 6 to 7 mm thick, coloured glazed ceramic tiles as in skirting/dado laid and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick rendering in cement mortar (1:4) including triangular filleting on top complete all as specified and directed.

M & L (Light shade) Virified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the colur of tiles over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

M & L for machine cut cudappa stone slab 20-25 mm thick laid and jointed with grey cement slurrg using as support of washing basin platform including rubbing and polishing complete all as specified and directed.

M & L granite (of any type) work (table rubbed and polished) 18 to 20 mm thick in steps, jambs, pillars, window cill, cooling platform, wash basin platform including cutting and flooring in CM 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite with and including screed bed or bedding layer 15 mm thick, in CM 1:6 on stone masonry surfaces.

M & L for machine mode precast cement concrete interlocking Paver block (glossy finish) any shape and size coloured conforming to IS 15658-2006 of 60 mm thickness M-35 grade laid over and including 30mm thick sand cushioning laid dry complete all as specified and directed.

M & L for coloured glazed chequered cement concrete tiles of size 30 cm x 30 cm x 25 mm thick, with grey cement and pigments, et, jointed and pointed in neat cement slurry complete all as specified and directed.

M & L for 10mm thick cement plaster in CM 1:6 on brick surface and finished even and smooth without using extra cement complete all as specified and directed.

M & L for 15mm thick cement plaster in CM 1:4 on brick or concrete surfaces using water proofing compound as per manufacturer's instruction and finished with sponge finish complete all as specified and directed. Note : WPC shall be measured and paid separtely.

Supply only integral water proofing compound.

M & L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over one coat of primer complete all as specified and directed.

M & L for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

M & L for preparation of new wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer all as spd and directed.

M & L for preparation of new steel or iron surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

S & F salt glazed stone ware gully traps square of size 150 x 150 mm including setting & jointing to drains in CM (1 : 2) including earth, concrete in beds, surrounds, kerbs ettc and CI grating etc complete fixed in repairs, all as directed by Engr -in- Charge.

S & F PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

All as per item No 76 here-in-before but 75mm dia pipe.

All as per item No 77 here-in-before but laid in trenches.

M & L PVC (SWR) 110 mm dia bends any radius complete all as specified and directed.

All as per item No 79 here-in-before but 75mm dia.

M & L 100mm dia PVC (SWR) branch piece, double (double Y) equal or unequal complete all as specified and directed.

M & L 75mm bore PVC (SWR) vent cowl complete all as specified and directed.

S & F waste pipe PVC low density polytheline 32 mm dia complete all as specified and directed.

S & F 1000 lit Rotational moulded polythylene water storage tanks double layered (cylindrical vertical with closed top) hoisted and fixed in position including 20mm dia. ball brass valves, high pressure, with polythene float and fly nut complete all as specified and directed.

S & F 20mm bore gun metal globe or gate valves with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S & F GI tubing "medium grade" galvanized with all fittings and fixed complete to walls and ceilinng or laid in floors etc complete all as specified and directed :-

15mm bore

20mm bore

S & F for brass chroumium plated tubular towel rail 20 mm dia "D" type 60 cm long complete all as specified and directed.

S & F in repairs vitreous china wash down water closet pan ( pedestal pattern ), white including connection to drain ( or outgoing pipe ) and to flushing pipe with and including S & F plastic water closet, seat white closed pattern with flat bottom, cover and mild steel hinging device.

S&F for PVC Valve less syphonic action type flushing cistern low level white ,with inlet ball valve float and handle including brackets & flush pipe of polyethylene of low or high density PVC 32 mm dia for low level cistern to squatt pattern closet etc.

S & F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed.

S & F vitreous china squatting pan (Orissa pattern) size 580 x 440mm white with integral footrest Including provision of cement concrete bedding complete all as specified and directed.

S & F for vireous china wash basin, white, flat back, size 630x450 mm excluding taps, waste pipe and but including waste coupling and brakets complete all as specified and directed.

S & F in repairs 15 mm bore bib taps, fancy type cast copper allowy chromium plated with crutch or butterfly handle, screwed down and screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repair 15mm bore stop valve cast copper alloy chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in repairs 15 mm bore pillar taps, fancy type cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lattered "HOT" or "COLD" with long screwed shanks and fly nuts, complete.

S & F PVC connection 60cm long 15mm dia, with 2 Nos CP brass check nuts all as specified and directed.

S & F 150mm size square grating of PTMT (min weight 100gms) complete all as specified and directed.

M & L for reinforced concrete pipes class NP2 150 mm bore laid and jointed complete with collars all as specified and directed.

M & L for Concrete bed to drain pipes including packing under and haunching against the sides of pipe and completely surrounding pipes with concrete after they are laid and tested, in cement concrete 1:3:6 type C2 for 150 mm complete all as specified and directed.

Supply and laying 20mm bore pipe Galvanized, medium grade includingall fittings complete.

Cutting existing steel tubing for alterations or addition of size 20mm for proper connection complete all as directed.

M & L for Point wiring using colour coding as per IS with 1.5 Sq mm multistranded copper conductor single core FRLS PVC insulated sheathed 1100 Volts, ISI-694 marked drawn through Casing & Capping on wall /roof/ floor along with suitable fittings, with MS sunken boxes of 1.6 mm thick of suitable size including making good disturbed surfaces to match with existing finishes including 3mm thick laminated sheet ISI marked for having switches sockets etc along with1.5 Sq mm copper conductor FRLS, PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly including taking dwon old existing point wiring fixtures nad fittings complete all as specified for the following :-

One light point controlled by one, one way switch

One ceiling fan point controlled by one, one way switch and regulator.

One three pin 5 Amps socket outlet point controlled by one No one way switch on same board

One three pin 5 Amps socket outlet point controlled by one No one way switch on independent board

All as per Item No 103 here-in-before but with stranded copper conductor 2.5 Sq. mm (nominal area), single core, PVC insulated and unsheathed multistranded FRLS cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent, including PVC insulated multistranded FRLS copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly.

S & F for Switch piano, flush type single pole, one way 5 Amp all as specified.

S & F for Switch piano, flush type single pole, one way 15 Amp complete all as specified.

S & F for Socket outlet 2 in 1, 3 pin, 5A complete all as specified.

S & F for Socket outlet 2 in 1, 3 pin, 5 and 15 amp flush type complete all as specified.

S & F Single pole and neutral metal clad type enclosure with a two pin and earth plug and socket complete with one single pole 20 A MCB for AC, all as specified.

M & L point wiring complete with and including single core FRLS PVC insulated un- sheathed flexible bright annealed multi stranded copper conductor cables 1.5 sqmm (22/0.30mm ) 1100Volts grade drawn through and including heavy grade PVC rigid conduits 20 mm or higher dia as required at site, totally concealed in walls /floors/ceiling/roofs etc. including all conduit accessories/fittings/junction boxes/inspection covers etc. of heavy grade, ISI marked and modular type sunken boxes factory made including 1.5 sqmm 1100 V grade FRLS PVC insulated, unsheathed flexible multi stranded copper conductor cable as continuous earth wire connected to metallic bodies of luminaires/fans etc. at one end to common earth dolly at other end, complete all as specified. Note- (i) Making good of distrubed surfaces matching with the surrounding will be done by contractor without any extra cost (ii) Cutting in chases and making good to facings and pointing in cement mortor will be done by contractor without any cost.

One light/fan point controlled by one, One-way switch complete all as specified

One 3/5 pin 6 Amp Socket outlet point on same board with other switches including earth wire.

S & F modular switch 6A SP one - way 230V white ivory finish complete all as specified

S & F modular socket outlet 2/3 pin 6 amps, multipurpose 2 module 230 Volts, single pole one way suitable for plug tops, complete all as specified.

Supply and fixing in replacement the following accessories -:

White cover plate with frame, 2 module complete all as specified.

White cover plate with frame, 6 module complete all as specified.

S & F for ceiling rose 2/3 terminals, PVC/ polycarbonate, isolated body ISI marked complete all as specified.

S & F for MCB DB, SPN, sheet metal enclosure, 8 way with 200 amps rated bus bar double door, fixed on wall good to disturbed surfaces, and connecting with cable complete all as specified.

S & F for MCB double pole of rated capacity 32 amps, 240 volts breaking capacity 10 KA, C-curve complete all as specified.

S & F for MCB Single pole rated capacity 6 to 32 amps, 240 V breaking capacity 10 KA ,C- curve complete all as specified.

S & F LED light fitting 10 watt complete in all respect having high luminaire, integrated LED channel with white acrylic cover of 10W cap.Cat Part No BCLSB10WH of Bajaj or equivalent model from the specified make given in PS.

S & F LED light fittings 2'x2', 28 watts environmental friendly, new genereation, aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source 230 volts with all accessories internally pre wired and necessary mounting arrangements, including taking dwon old existing llight fittings complete all as specified and as directed. Make :- Make HAVELLS Cat part No. PLUTONEO2X2PLR28WLED840S (HSN 9405) 28 W or equivalent model from the specified make given in PS.

S & F LED Tube light fittings wall mounted, 18 W LED 6500K with Opal white Poly Carbonate diffuser provided with high efficient integral constant current LED Driver 230 V etc. complete with mounting batten including all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size from ceiling rose to connector Conforming to Cat Part No. BLRB DB 118 & BLRB18 W CW LED Make :- Bajaj or Equivalant model from the specified make given in PS.

S & F LED energy efficient Security light fitting 25 Watt LED, pressure die cast aluminium housing in heat resistant glass covered with IP 65 Protection and including GI pipe as required length and size with fixing accessories including taking down old existing light fittings complete all as specified and directed. Make - Bajaj Cat Part No. BCLST 25W LED I V2 or equivalent model from the specified make given PS.

S & F LED security light of 30 watt capacity complete with all accessories and wall mounting bracket of suitable size including clamps, nut bolts etc. prewired Conforming to Bajaj Cat Part No. BCLST 30W LED I or equivalent model from the specified make given in PS.

M & L Sub main wiring with 2 single core FRLS PVC insulated unsheathed, multi-stranded flexible copper conductor 1100 volts grade cables 4.0 sqmm, drawn through and including rigid FRLS PVC heavy grade on and including Casing Caping with 1 single core 4.0sqmm 1100 volts FRLS grade PVC insulated unsheathed multi stranded flexible copper conductor cable as countinous earth wire and connecting to common earth terminals including taking dwon old existing submain wiring complete all as specified and directed.

S & F Energy Efficient Ceiling Fan of 1200 mm sweep, high speed, low power consumption, Superior Aluminium Blades and provision of 3 core flexible copper conductor cable of size 23/0.19 from ceiling rose to ceiling fan complete with and including electronic fan regulator all as specified and as directed. Conforming to Cat Part No. KASSELS STAR of Make :- Bajaj or Equivalant model from the specified make given in PS.

S & F exhaust fan of sweep 300mm with louver heavy duty single phase suitable for 230 volts 50 HZ,1400 rpm and connecting up complete including provision of 3 core flexible cord from ceiling rose to connector of fan with cable of suitable size. Make :- Bajaj, Item Code - 70068 SUPREME PLUS or equivalent model from the specified make given in PS.

Taking down ceiling fan/ exhaust fan of any sweep, keeping with safe custody and refixing the same with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal over hauling the fan, Painting of ceiling fans complete with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc. complete all as specified.

M & L for earthing with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm buried directly in ground earth pit not less than 2.25 m deep below normal ground level, with top edge of the plate vertically to depth of not less than 1.5 m below ground level connected to and incl GI wire 4 mm dia and GI pipe 20 mm dia light grade for protection to the extent of 7.5 m as earthing lead by means of GI bolts and nuts etc connecting to equipment with provn of charcoal and salt etc all as per electrical plate No 3 of SSR Pt-I incl RCC cover and MS angle iron frame, watering arrangement with GI pipe 20 mm dia and MS funnel, concrete pit incl excavation and earth work in any type of soil and testing on completion etc complete.

M & L for reinforced concrete pipe of dia 100mm 2 Nos half round (for bottom and top) complete all as specified and directed.

Supply, lay and testing XLPE insulated armoured heavy duty electric power cable 1100 volt grade with standered aluminimum conductor of size 10 Sqmm 2 core complete all as specified and directed.

M & L for 15mm thick cement plaster in CM (1:6) on bricks/ block masonry and finisheing the surface even and smooth with using extra cement complete all as specified and directed.

M & L for preparation of old painted steel surface of any description over 10cm in width or girth and applying one coat of syntetic enamel paint complete all as specified and directed.

durga consrtruction

Suma Construction