ADDN ALTN TO ROOF TERRACE ADITI AHILYA COMPLEX AND PROVISION OF PARKING SHED FOR 04 GROUND POWER UNITS (GPUs) AT INS SHIKRA

Amount

Note : ITEMS TO BE EXECUTED AT TERRACE FLOOR OF G+12 BLDG, RATE QUOTED TO BE INCLUSIVE OF NECESSARY SCAFFOLDING, SAFETY MEASURES ETC.

Submission of detailed drawing (plan section ,elevation, side views) structural, electrical, architectural drawings for parking shed for 04 Nos ground power Unit (GPU) designed by structural consultant as recommended by Garrison Engineer.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out any type soil and circumstance all a specified and directed.

Excavation in trencehes n exc 1.5 mr wide & N exc 1.5 Mtr deep and getting out in soft/loose soil all as specified and directed.

Excavation in trencehes exc 1.5 mr not exc 3mtr and getting out in soft/loose soil all as specified and directed.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation all as specified and directed.

Labour only for soil filling , layer not exceeding 15 cm well ramming and watering , excavated earth shall be reused for filling all as specified and directed

Returning, filling in, including spreading, levelling , watering and well ramming in layers not exc 25 cm in hard/ dense soil.

M&L for RCC (design mix), M-30 in foundations, including rafts, footings, foundation beams; bases for columns, etc; basement slabs, under reamed piles and mass concrete

M&L for RCC (design mix), M-30 in beams, plinth beams;cantilevers, bressummers, lintels over 1.5 mtr span

M&L for RCC (design mix), M-30 in Columns, pillars, piers, posts and struts etc.

M&L for RCC (design mix), M-30 in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc

M&L for RCC (design mix), M-30 in chajjas etc.

Use & waste form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foudation and plinth beams, and similar work, vertical of to batter. on flat rough finished surfaces of concrete.

Use & waste form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work , not exceedig 200mm thick on flat rough finished surfaces of concrete.

Use & waste form work to chajjas including edges on flat rough finished surfaces of concrete.

Use & waste form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including suports, overhangs, etc on flat rough finished surfaces of concrete.

Use & waste form work to sides of pillars, posts, sruts, piers, columns and stanchions on flat rough finished surfaces of concrete.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending , hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia.

Ditto as item no 19, but 5 mm dia and over in stirrups, spacers and binders.

M&L brick work with sub class B bricks straight or curved on plan exceeding 6 m mean radius built in CM 1:6 complete all as specified and as directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM (1:4), complete all as specified.

M&L for Providing precast cement concrete louvers and jallies 25 mm thick type B0 1:2:4 12.5 mm graded aggregate including all mouldings but excluding set in cement mortar 1:4 all as specified and directed.

Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point.

M&L for rendering 15mm thick in CM 1:6 on brick surfaces, finished even and smooth without using extra cement on walls complete all as specified and as directed.

M&L for rendering 10mm thick in CM 1:3 on concete surfaces as in ceiling finished even & smooth without using extra cement in ceiling.

M&L for rendering 15mm thick in two coats on brick work or concrete surfaces in cement mortar 1:4 finished even and fair including mixing integral water proofing compound on finishing coat in the proportion as mentioned in manufacturer's instructions (Note-Water proofing compound to be measured and paid for separately).

Supply only integral water proofing compound complete all as specified.

M&L for applying 3mm thick wall care putty on wall surfaces

M&L for applying two coats of oil emulsion distemper over newly plastered/ putty surfaces of wall including preparation of surface all as specified and as directed by Engr in-Charge

M&L for preparation of newly plastered surfaces of ceiling and applying two coat of oil emulsion distemper complete all as specified and directed by Engr in-Charge

M&L for preparation of newly plastered surfaces of wall, soffits, facia roof and applying two or more coats of 100% weather acrylic base paint over one coat of cement based primer with necessary scaffolding etc all as specified and as directed by Engr in-Charge

M&L for anti termite treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surfae area.

M&L for anti termite treating the back fill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surfae area.

M&L for anti termite treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface.

M&L for anti termite treating the soil under plinth protection at the rate of 5 litres of emusion per squaremere of surface area.

M&L for anti termite treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall.

M&L for hardcore of gauge n exc .63 mm , deposited, spread and levelled in layers n exc 15 cm thick , watered and well rammed to a true surface.

M&L for 100 mm thick cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) as in sub base.

M&L for 75 mm thick cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate)as in plinth protection including finishing the surfaes even and smooth without using extra cement.

Supply and fix Pre-painted Galvalume Aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified

S&F pre-painted galvalume aluminium zinc coating GI base plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in ridge of roof covering / cladding to wall, fixed with self tapping screws/L-type or J-type or cranked hook bolts complete all as specified and directed.

S&F steel work roof trusses including special shaped washer etc complete using ERW or induction welded tubes confirming to IS 1161-1979 grade St-240 Complete all as specified and directed by Engr-in-charge.

M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile 0.11 Sqm but n.exc 0.18 Sqm, in neat cement slurry and pointed in white or coloured cement with pigment to match over 15mm thick screed bed in cement mortar (1:6) all as specified and directed.

M&L for coloured glazed ceramic tiles 450x300x7 mm thick but as on vertical surfaces such as skirting/dado including 10mm thick rendering in CM 1:3 al las specified and directed.

M&L for Granite (of any type) 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete.

Tool & labour for Rounding edges of stone slabs , such as in steps, cooking platform and making grooves for lining and other similar work complete all as specified and directed.

S&F Anodised aluminium snap grid size 605x605mm frame work for false ceiling all as specified.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified

M&L for false ceiling made out of 600x600x4 mm thick ( non asbestos fiber cement designer/coloured)ceiliing board / tiles deep panel.

S&F powder coated aluminium (minimum 25 micron thickness of coating) of various section as required for doors, sliding windows/ partion/Ventilator etc including fixing and making the frames for hinges glass/wire gauge etc. Complete incl all fittings like rubber beading, clips locking arrangement,in sliding shutter, sealant etc all as specified and as directed by Engr- in- charge.

S&F aluminium grill with and including suitable aluminium anodised frame F/H section as requird manufactured by approved make as per design No DG- 102, 7.5 mm thick all as specified and as directed by Engr- in- charge.

S&F 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts all as specified.

S&F aluminium anodized barrel tower bolts 200 mm of extruded section and fixed.

S&F 150mm size aluminium alloy handles, febricated type extruded section, ISI marked all as specified.

S&F Stainless steel butt hinges 100 mm.

M&L for MS flat for hold fast. Conforming to Fe-290-0 or Fe-165.

S&F 140 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring all as specified.

S&F Aluminium extruded body door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width of weight not more than 35 kg and fixed as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed bed in CM (1:4) 15mm thick, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete.

M&L for machine cut kota stone slab flooring 20-25mm thick in riser / treads of steps in single piece, skirting, dado and pillar laid over cement screed and jointed withover cement screed bed in CM (1:4) 15mm thick, & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing and rounding the edges where as required complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 20 mm graded stone aggregate cement concrete as in flooring, roof kerb, mud stop course on roof surfaces and coping etc.

M&L for Machine pressed precast concrete interlocking paver block having glossy finish shape and size as approved by GE confirming to IS 15658-2006 of 60mm thickness of M-35 grade, with grey cement and pigments laid over and including 50 mm thick dry sand cushioning and voids filled with dry and surface compact, including compaction by means of surface vibrator complete all as specified and directed.

M&L providing and laying kerb stone , concrete blocks,finished surface even and smooth in position to the requied line level curvature jointed with cement mortar 1:3 including making joints with or with out grooves including making drainage opening where ever requied.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/trenches.

S&F PVC (SWR) bends 110 mm.

S&F 2nd class hard wood (sal) plain, solid, straight chowkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints all as specified.

S&F 40mm thick flush shutters, solid core construction, with block board core and ply wood face panels, commercial type on both side.

M&L for preparation of newly wooden surfaes of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces.

M&L for roughening surfaces of concrete surfaces and 15 mm thick screeding in cement mortar 1:4 finished even and smooth without using extra cement.

M&L for Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification & drawing all as specified and directed.

M&L for Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the styles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification and drawing all as specified and directed.

S&F vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe.

S&F vetreous china coloured Urinal partition size 300X700 mm all as specified and directed.

S&F viterous china ware wash down water closet pan (Pedestal Pattern) coloured and plastic seat and cover with MS CP hinges (excluding fixing bolts), flushing cistern and floor pipe complete.all as specified

S&F vitreous china wash basin coloured, flat back, size 550 x 400mm, fixed with brackets incl 32mm bore CP waste coupling, flexible waste pipe etc ,all as specified and dircted..

S&F PVC valveless syphonic action type flushing cistern, low level,coloured, with inlet, ball valve, float and handle including flush pipe fixing to EWC all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of lentyh 450mm all as specified and directed.

S&F Health faucet (ABS Body) of aprroved make mild steel chromium plated suitable for 15 mm dia pipe with 1.00 metre long spirochrome Flexible tube and wall hook including making connections and fixed in position complete all as specified and directed.

S&F fancy type CP Pillar tap 15 mm dia, with capstan heads, screwed down high pressure, with long screwed shanks and fly-nuts, screwed and fixed complete all as specified.

S&F 15mm bore CPVC pipes of pressure rating 10 Kg/cm2 fixed complete to wall or ceiling or in floor etc. with all fitting and where ever concealled complete all as specified.

S&F 15mm bore stop valves/ Angle valve , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed all as specified and directed.

S&F twin Bib tap 15 mm CP withn srewed for iron pipe or for brass ferrule and fixed all as specified.

S&F 15mm dia concealed fancy type stop valve copper alloy with chromium plated fixed to iron pipe all as specified.

S&F looking mirror 450X600mm with plywood backing and aluminium frame all as specified and directed by Engineer-in- Charge.

S&F Stainless steel Towel rail 600mm long including necessary brackets complete all as specified and as directed.

S&F stainless steel soap dish holder of approved make fixed with brass screw to wall complete all as specified and directed.

S&F 75 mm bore PVC (SWR) Soil, waste and vent pipes double socketed in any length with rubber ring joints fixed to walls complete all as specified and directed..

S&F 100mm bore cast iron cowls all as specified and directed.

S&F PVC (SWR) 'P’ trap 100mm bore all as specified and directed.

S&F PVC (SWR) Floor trap of 75 mm outlet plain with grating including jointing with solvent cement all as specified and directed.

S&F 200mm bore RCC pipe class NP-3 laid and jointed complete with collers as specified including testing all as specified and directed by Engineer-in-Charge.

M&L for cement concrete 1:3:6 type C-2 (using 40mm graded stone aggregate) as in bed to drain pipes including forming cradle after they are laid and tested for 200mm bore RCC pipe complete all as specified and as directed by Engineer-in-Charge.

M&L precast reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in manhole covers and the like set in cement mortar (1:4) duly placed on manholes complete all as specified and directed by Engineer-in-Charge.

Cutting into existing manhole for connecting new drains and making good to pipes and rendering cutting out existing benching for and forming branching for and forming branch channel (1/2 round or ¼ section ) in PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate smooth finished and reforming benching as specified and directed for 150mm dia of pipe complete all as specified.

S&F rotational moulded polythylene water storage tank of 500 ltr capacity hoisted including 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210 grms ) all as specified.

S&F 12 mm MDF board exterior grade fixed with screw on aluminium frame work for cupboard with hinges, latches, handle, lock and all necessory fittings etc complete all as specified and directed.

M&L for Cement concrete (1:3:6) type C-2 by using 40mm graded stone aggregate as in foundations, filling and mass concrete, complete all as specified & directed.

S&F Rolled mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc, as in vertical post and fixing of post with drilling and fixing with fastener of required size conforming to Fe-290 (gde E-165) complete all as specified and directed.

S&F Rolled mild steel in Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-290 (gde E-165) complete all as specified and directed.

S&F Rolled mild steel in wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire, etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work roof including securing bolts, conforming to Fe-290 (gde E-165) complete all as specified and directed.

M&L for Preparation of new steel surafces & apply two coats of black bituminous paint exceeding 10cm in width or girth, complete all as specified.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water, complete all as specified.

M&L for 100 mm thick PCC 1:4:8 type D2 (Using 40mm graded stone aggregate) as in sub base complete all as specified and directed.

M&L for Sand filling under floors or in foundation including watering and consolidation all as specified and as directed.

M&L for Machine pressed precast concrete rubber finished paver block of size approved layout pattern and colour as approved by GE and thickness of 60 mm confirming to IS 15658-2006 of M-35 grade design mix concrete complete all as specified and directed.

M&L for Point wiring complete with 1.5 sqmm single core multistranded FRLS PVC insulated unsheathed copper conductors 1100 volts grade drawn through & including PVC non-metallic casing and caping of size not less than 25mm width, including PVC bend, tee joints etc as per site requirement ISI marked with accessories fixed on wall/ceiling/truss etc with PVC non metallic ISI marked terminal boxes / modular boxes surfacing on wall including one FRLS PVC insulated & unsheathed multistranded green colour copper conductor 1.5 sqmm as earth continuity conductor connected to common earth as earth dolly for the following :

(a) One light point controlled by one switch SP one way.

(b) One ceiling fan point controlled with one 5A switch.

(c) One exhaust fan point controlled with one 5A switch.

(d) One 3 pin socket outlet 5Amps on independant board.

(e) One 3 pin socket outlet 5Amps on same board with other switches.

M&L for point wiring for 15 Amps socket complete with 2.5 sqmm single core multistranded FRLS PVC insulated unsheathed copper conductors 1100 volts grade drawn through and including PVC non-metallic casing and caping of size not less than 25 mm dia including PVC bend, tee joints etc as per site requirement, ISI marked with accessories fixed on wall/ceiling/truss etc with PVC non metallic ISI marked terminal boxes / modular boxes surfacing on wall including one FRLS PVC insulated & unsheathed multistranded green colour copper conductor 2.5 sqmm as earth continuity conductor connected to common earth as earth dolly.

S&F Modular Switch , 6Amp, One way, 1 module, ISI marked.

S&F Modular Switch , 16Amp, One way, 1 module, ISI marked

S&F Modular Socket , 6 Amps, 2/3 pin combined 2 module, ISI marked.

S&F Modular Socket , 16Amps, 6 pin combined 2 module, ISI marked.

S&F Modular type, electronic fan regulator ( 5 step ), 120 Watts, 230 volts, 2 module, ISI marked.

S&F ceiling rose surface bakelite with ISI mark, flush type with ISI mark three terminals complete all as specified.

S&F Modular white cover plate with Frame 3 Module, ISI marked.

S&F Modular white cover plate with Frame 6 Module, ISI marked.

S&F Modular metal flush box 3 module, ISI marked and incluing cutting hole in wall / ceiling/piller etc and making good surface.

S&F Modular metal flush box 6 module, ISI marked and incluing cutting hole in wall / ceiling/piller etc and making good surface.

Supply and fixing LED lights fitting 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fixing submain wiring with proper colour coding, 2 single core FRLS 1100 volts grade cable with stranded copper conductor of size 4 Sqmm in and including PVC non-metallic casing and caping of suitable size not less than 25 mm , ISI marked including 1 single core cable with stranded copper conductor of size 4 Sqmm (green colour) for earthing. Note : (i) 2 runs of 4 Sqmm cable, 1 run of PVC Conduit and 1 run of 4 Sqmm cable shall be measured as 1 Run. (ii) Each Submain Wiring shall run in Seperate PVC Conduit.

S&F double door metallic sheet metal enclosure MCB DB SPN 8 ways, 240 V with 200 Amps rated bus bar complete fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs of cables/wires all as directed.

S&F double door metallic sheet metal enclosure TPN 4 ways, 415 V complete fixed properly on in concealed position and to provide required sizes of flexible conduit at any open surfaces near DBs of cables/wires all as directed.

Supply and fixing TPN 40-100 Amp, 415V 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection complete all as specified and directed.

Supply and fixing MCB SPN 40 to 63 Amp, 240V, 10KA 'C' curve complete all as specified and directed.

Supply and fixing MCB SP 6 to 32 Amp, 240V, 10KA 'C' curve complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed by the Engineer-in-Charge.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm all as specified and directed at site.

Material & Labour for Earthing with galvanised steel earth plate electrode 60 x 60 cm x 6 mm thick, burried directely in ground (earth pit not less than 2.5 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanised earth lead wire 4.0mm with the help of bolts, nuts, check nuts and washers of galvanised iron or steel, including necessary excavation, PCC 1:3:6 type D2 and PCC cover 1:2:4 type B1 watering arrangement with GI pipe funnel, jali, and cast iron cover fixed on top of pit complete all as specified and shown in electrical plate No.3 including connection to the earthing test point and testing on completion.

Supply, laying including testing and commissioning PVC insulated XLPE, armoured LT cable, 1100 Volts grade with aluminium conductor of size 3.5 core 50 Sqmm laid through pipe /ducts or fixed on wall etc complete all connections to LT panel with proper size glands & lugs all as specified & directed.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 240 V, 20 Amp complete all as specified and directed.

S&F Triple pole and earth encolsure with a three pin and earth plug with socket complete with one triple pole MCB 63 Amp 415 Volt complete all as specified and directed.

I.J Enterprises (BID ID -3494934)

M S CONSTRUCTIONS (BID ID -3489004)

HINDUSTAN BUILDERS (BID ID -3489313)

JANKI ENTERPRISES (BID ID -3487361)

GANGAJAL (BID ID -3486428)